Add SVC operations for fine grain control over vsys, refclk, and unipro
port power.

Testing done: used "new" firmware boot sequence to verify that modules
              were correctly detected and booted.
Signed-off-by: Jeffrey Carlyle <jcarlyle@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

This reverts commit 571348253032a86e4f0102d4dfadd390d0ea7e64.

With this patch gb_bootrom_timedout was getting called in interrupt
context and then proceeding to call functions that might block. In
practical terms, this was leading to a kernel BUG at mm/vmalloc.c:1650.
Signed-off-by: Jeffrey Carlyle <jcarlyle@google.com>
Acked-by: Johan Hovold <johan@hovoldconsulting.com>

As per greybus specification, the AP can apply, implementation
dependent, timeouts for:

- The time interval between the Find Firmware Response and the first
  Fetch Firmware Request.
- The time interval between a Fetch Firmware Response and the next Fetch
  Firmware Request.
- The time interval between a Fetch Firmware Response and the Release
  Firmware Request.
- The time interval between the Find Firmware Response and the Release
  Firmware Request.

This patch implements those timeouts.

The timeout period for the first three cases is fixed to one-second and
the timeout for the last one is finalized at runtime, dependent on the
total size of the firmware.

There can be two possible paths now, which may race for freeing or
getting the 'struct fw_request'. They are:
- Request handler: initiated from the Module side.
- Timeout handler: initiated on timeout of the programmed timer.

And so a mutex is added to avoid races.

Every caller which needs to access the 'struct fw_request' increments
the reference count, so that the structure doesn't get freed in
parallel. Once the structure is freed and reference is put by all the
users, the structure is freed.

If we timeout while waiting for a request from the Module, the AP frees
the 'struct fw_request', but does *not* free the request-id. This is
done to guarantee that a delayed request from the Module for the expired
id, doesn't get access to a new 'struct fw_request' allocated later with
the same id.

Tested with gbsim by hacking its code to delay the release request and
indefinitely fetch the same section of the firmware package. Both timed
out on the AP side and the 'struct fw_request' is free properly. Further
requests work fine after few are timed out. And rmmod (followed by more
similar testing) works just fine.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

This patch updates the fw-download core to manage firmware requests with
kref. This is required for the next patch, which will introduce timeouts
for firmware downloads.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

This patch simplifies and improves the readability of the internal state
transition logic of arche platform driver state transition logic by:

1. Making a dedicated function to state-transition the platform code.
2. Condense the decision to swtich states down to a single switch
   statement instead of four separate if/else clauses.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Suggested-by: Alex Elder <elder@linaro.org>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

With the addition of the timesync driver and looking at the hardware
interfaces we have, its clear we need to add a new arche-platform state.

This patch adds ARCHE_PLATFORM_STATE_TIME_SYNC to the arche-platform driver
to facilitate transition to the TIME_SYNC state if-and-only-if the
arche-platform driver is in the ACTIVE state.

This is mainly needed as wake/detect lines are shared between TIMESYNC
operation and basic control functionality of APBs. So during TIMESYNC
we want to make sure that the events on wake/detect lines are
ignored by the arche-platform APB reset logic.

This patch adds one exported function, which can be invoked from
timesync driver code, allowing, switching between
ARCHE_PLATFORM_STATE_TIME_SYNC <=> ARCHE_PLATFORM_STATE_ACTIVE states.

[ bryan.odonoghue@linaro.org: Added mutex, massaged commit text ]
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Suggested-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

With addition of exported function, required for TIMESYNC operation,
we need more locking mechanism for driver state, so to avoid confusion
rename existing spinlock variable to its appropriate name.

Testing Done: Tested on DB3.5 platform.
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

In order to verify TimeSync functionality we require a TimeSync-ping
operation where the AP can command the SVC to initiate a single strobe of
downstream TimeSync slaves, and report the FrameTime at the strobe. Ping
will only be valid after the system has transitioned to a TIMESYNC_ACTIVE
state.

In the active state each TimeSync slave will graph a single incoming SVC
strobe as a ping and will store its frame time. The AP will then gather
each last-event FrameTime for presentation to user-space in the AP and/or
further automation based on the reported FrameTimes at the SVC ping.

This patch adds the SVC ping command definition to greybus_protocols.h.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Its necessary to establish an initial state on the wake-detect lines before
enabling timesync on APB/GPB in order to ensure all GPIO edge-transitions are
correctly interpreted by the receiving processor.

This patch adds the operations defined in the Greybus specification to
greybus_protocols.h, this involves adding the
SVC_TIMESYNC_WAKE_PINS_ACQUIRE and SVC_TIMESYNC_WAKE_PINS_RELEASE commands
and moving the 'strobe_mask' parameter from 'struct
gb_svc_timesync_enable_request' to 'struct
gb_svc_timesync_wd_pins_acquire_request' since the communication of the
strobe_mask will be communicated before preparing any of the bridges to
receive the TimeSync pulses.

A separate patch to the greybus specification describes the transition
between the wake sub-state and the timesync sub-state.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

We should use tabs not spaces when indenting multi-line macros and ensure
that the relevant '\' characters are aligned to each-other.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

This was done long back and was probably the best bet then, but it looks
really bad to have it this way now.

Kill the hack and implement proper driver init()/exit() routines to do
the same thing.

Tested using gbsim by hotplugging uart manifest and removing it later.
Also tried removing the gb-phy module to test the exit path properly.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Update the documentation (sysfs-bus-greybus) for recent conversion of
bridged-phy drivers to real drivers.
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

This converts the USB driver to be a gpbridge driver, moving it away
from the "legacy" interface.

It's not like this code even does anything at the moment, how much
trouble could we cause with this change?  :)

Testing Done: Tested on gbsim.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
[vaibhav.hiremath@linaro.org: 1.Changed code to retain init/exit fns of
drivers. 2.Exit path fix. 3. Fixed review comments]
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

This converts the SPI driver to be a gpbridge driver, moving it away
from the "legacy" interface.

Testing Done: Tested on gbsim.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
[vaibhav.hiremath@linaro.org: 1.Changed code to retain init/exit fns of
drivers. 2.Exit path fix. 3. Fixed review comments]
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

This converts the SDIO driver to be a gpbridge driver, moving it away
from the "legacy" interface.

Testing Done: Tested on gbsim.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
[vaibhav.hiremath@linaro.org: 1.Changed code to retain init/exit fns of
drivers. 2.Exit path fix. 3. Fixed review comments]
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

This converts the GPIO driver to be a gpbridge driver, moving it away
from the "legacy" interface.

Testing Done: Tested on gbsim.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
[vaibhav.hiremath@linaro.org: 1.Changed code to retain init/exit fns of
drivers. 2.Exit path fix. 3. Fixed review comments]
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

This converts the I2C driver to be a gpbridge driver, moving it away
from the "legacy" interface.

Testing Done: Tested on gbsim.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
[vaibhav.hiremath@linaro.org: 1.Changed code to retain init/exit fns of
drivers. 2.Exit path fix. 3. Fixed review comments]
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

This converts the PWM driver to be a gpbridge driver, moving it away
from the "legacy" interface.

Testing Done: Tested on gbsim.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
[vaibhav.hiremath@linaro.org: 1.Changed code to retain init/exit fns of
drivers. 2.Exit path fix. 3. Fixed review comments]
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

This converts the UART driver to be a gpbridge driver, moving it away
from the "legacy" interface.

Testing Done: Tested on gbsim.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
[vaibhav.hiremath@linaro.org: 1.Changed code to retain init/exit fns of
drivers. 2.Exit path fix. 3. Fixed review comments]
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

gb_connection_disable_rx() fn is required to be used by other modules
(e.g. bridged-phy drivers) and so export it.

Testing Done: Tested on gbsim.
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

In order to help bridged-phy drivers to define init()/exit()
functions, define helper macro in gpbridge.h file.

Testing Done: Tested on gbsim.
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

This creates a gpbridge "bus" that will be used to create devices that
are the bridged phy devices that correspond to the protocols being
implemented.

Testing Done: Tested on gbsim.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
[vaibhav.hiremath@linaro.org: 1.Changed code to retain init/exit fns of
drivers. 2.Exit path fix. 3. Fixed review comments]
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

This reverts commit b957ade7b3e4ab8c149c53346dbf02e977b7f3a7.

The interface version is now managed as part of the firmware-management
protocol. This operation is already removed from the greybus
specifications.

Drop interface version support from greybus.

Tested with gbsim (sysfs file not available after this patch).
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Acked-by: Sandeep Patil <sspatil@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Function gb_audio_manager_remove_all() to remove all audio modules,
doesn't control correctly 'ida' counting.
Signed-off-by: Dinko Mironov <dmironov@mm-sol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

SW-4894, SW-4389, and share a common root cause, namely that
the power-on reset configuration of the APBridgeA-Switch link of PWM
Gear 1, 1 Lane, Slow Auto, is insufficient to handle some required
traffic loads, such as 3 audio streams plus boot-over-UniPro or 4 audio
streams.

The correct long-term solution is to implement a UniPro Power Mode
Manager as in that considers the demands placed on the network,
and adjusts power modes accordingly.

The present commit implements a short-term, brute-force hack to allow
continued system testing:
- Upon receiving an SVC HELLO request, schedule deferred work to
  reconfigure the APB1-Switch link to PWM G2, 1 lane, Slow Auto
- When the Camera driver transitions a White Camera module from active to
  inactive, return the APB1-Switch link to PWM G2, 1 lane, Slow Auto

The Camera driver already steps up the APBridgeA-Camera link speed while a
camera module is active, which affords sufficient margin for simultaneous
audio and hotplug activity, and the Camera driver already steps down the
link speed thereafter: the change made by the present patch is simply to
tweak the stepped-down power mode to match the new baseline configuration.
Signed-off-by: Mitchell Tasman <tasman@leaflabs.com>
Tested-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

The new ctrl device under interface is missing a MODULE uevent var,
add it.

Testing Done:
cat 'uevent' from ctrl device.
$ cat 1-3.3.ctrl/uevent
DEVTYPE=greybus_control
BUS=1
MODULE=3
INTERFACE=3
GREYBUS_ID=fffe0001/ffee0011
Signed-off-by: Sandeep Patil <sspatil@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Its possible that the Module may fail to download the next stage
firmware, or to jump into it and boot into the new personality.

We have already seen examples of both of these cases on EVT 1.5.

This patch implements timeouts in the bootrom bundle driver, which now
expects the next request from the Module to be received at the AP within
1 second of the previous request/response. The time interval can be
increased later if required.

The timeouts are added between:
- AP_READY and FIRMWARE_SIZE operations
- FIRMWARE_SIZE and GET_FIRMWARE operations
- Two GET_FIRMWARE operations
- GET_FIRMWARE and READY_TO_BOOT operations
- READY_TO_BOOT operation and the call to the ->disconnect() event of
  the bootrom bundle (once the new hotplug request is received).

The timeout for the last case is kept at 5 seconds right now (random
value), as it may take a bit longer.

Because 'bootrom->fw' can be accessed simultaneously (from timeout
handler and incoming requests) and one of them can potentially free the
'->fw' structure, a mutex is also added to take care of such races while
accessing 'bootrom->fw' structure.

Also note that the '!bootrom->fw' check is moved to free_firmware()
routine.

Tested on EVT 1.5, by faking errors on certain requests, so that the
bootrom doesn't send any more requests. Normal case is working just
fine for audio and GP modules.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Use standard API greybus_set_drvdata() while setting private
data pointers for mgmt & data connection.
Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Earlier codec->lock protects almost complete register/unregister
module function. This can be reduced to specific operations.
Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Modify sequence of register_module & unregister_module in bundle
driver. This would affect the uevent generated for above user
space. Accordingly, we need to modify snd_soc_xxx sequence in
register_module() in codec driver.
Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Each module maintains connected status & a lock to protect it.
Using codec->lock we can safely serialize ASoC specific callbacks
(in response to mixer_ctl update or dai_ops) and gb module
disconnect. Thus is_connected field can be removed.
Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Remove unnecessary lock & list maintained in GB audio bundle
driver
Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

read/write_lock_irqsave mechanism was used to protect modules
list & kobject_xxx() in gb_audio_manager. Since kobject_xxx calls
can sleep spin_lock variants can't be used there. So use rw_sem
for protecting modules_list.
Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Create a macro representing the length of the firmware file's name and
use that instead of using magic number in the code.
Suggested-by: Greg Kroah-Hartman <gregkh@google.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

This patch adds Firmware Download Protocol support to firmware core,
which allows an Interface to download a firmware package over Unipro.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Jun Li <li_jun@projectara.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

The invalid request type has been redefined as 0x7f.

Also remove the redundant redefinition of the invalid type from the
operation header.

Note that operation type 0x00 has been repurposed for the new generic
ping operation, which will be used to implement proper connection tear
down.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Define the SVC version request, which need not need to stay the same as
the legacy version request.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Remove the unsupported version request from the loopback-driver request
handler.

Unsupported requests are already handled and logged using the default
case.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Implement the unidirectional mode-switch operation.

This operation will be used in the implementation of the new generic
mode-switch functionality.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Add helper functions for initiating unidirectional operations and
waiting for them to have been acknowledged as sent by the host device.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>