Doesn't change generated code.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the retrn value check which testing the wrong variable
in cfg_queues_uld().

Fixes: 94cdb8bb ("cxgb4: Add support for dynamic allocation of
resources for ULD")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nelson Chang says:

====================
net: ethernet: mediatek: add HW LRO functions

The series add the large receive offload (LRO) functions by hardware and
the ethtool functions to configure RX flows of HW LRO.

changes since v3:
- Respin the patch by the newer driver
- Move the dts description of hwlro to optional properties

changes since v2:
- Add ndo_fix_features to prevent NETIF_F_LRO off while RX flow is programmed
- Rephrase the dts property is a capability if the hardware supports LRO

changes since v1:
- Add HW LRO support
- Add ethtool hooks to set LRO RX flows
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the dts property for the capability if the hardware supports LRO.
Signed-off-by: Nelson Chang <nelson.chang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The codes add ethtool functions to set RX flows for HW LRO. Because the
HW LRO hardware can only recognize the destination IP of TCP/IP RX flows,
the ethtool command to add HW LRO flow is as below:
ethtool -N [devname] flow-type tcp4 dst-ip [ip_addr] loc [0~1]

Otherwise, cause the hardware can set total four destination IPs, each
GMAC (GMAC1/GMAC2) can set two IPs separately at most.
Signed-off-by: Nelson Chang <nelson.chang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The codes add the large receive offload (LRO) functions by hardware as below:
1) PDMA has total four RX rings that one is the normal ring, and others can
   be configured as LRO rings.
2) Only TCP/IP RX flows can be offloaded. The hardware can set four IP
   addresses at most, if the destination IP of the RX flow matches one of
   them, it has the chance to be offloaded.
3) There three RX flows can be offloaded at most, and one flow is mapped to
   one RX ring.
4) If there are more than three candidate RX flows, the hardware can
   choose three of them by throughput comparison results.
Signed-off-by: Nelson Chang <nelson.chang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allocate resources dynamically to cxgb4's Upper layer driver's(ULD) like
cxgbit, iw_cxgb4 and cxgb4i. Allocate resources when they register with
cxgb4 driver and free them while unregistering. All the queues and the
interrupts for them will be allocated during ULD probe only and freed
during remove.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 311b2177 ("sctp: simplify sk_receive_queue locking"), a call
to 'skb_queue_splice_tail_init()' has been made explicit. Previously it was
hidden in 'sctp_skb_list_tail()'

Now, the code around it looks redundant. The '_init()' part of
'skb_queue_splice_tail_init()' should already do the same.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The XDP_TX action can fail transmitting the frame in case the TX ring
is full or port is down.  In case of TX failure it should drop the
frame, and not as now call 'break' which is the same as XDP_PASS.

Fixes: 9ecc2d86 ("net/mlx4_en: add xdp forwarding and data write support")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mahesh Bandewar says:

====================
IPvlan introduce l3s mode

Same old problem with new approach especially from suggestions from
earlier patch-series.

First thing is that this is introduced as a new mode rather than
modifying the old (L3) mode. So the behavior of the existing modes is
preserved as it is and the new L3s mode obeys iptables so that intended
conn-tracking can work.

To do this, the code uses newly added l3mdev_rcv() handler and an
Iptables hook. l3mdev_rcv() to perform an inbound route lookup with the
correct (IPvlan slave) interface and then IPtable-hook at LOCAL_INPUT
to change the input device from master to the slave to complete the
formality.

Supporting stack changes are trivial changes to export symbol to get
IPv4 equivalent code exported for IPv6 and to allow netfilter hook
registration code to allow caller to hold RTNL. Please look into
individual patches for details.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In a typical IPvlan L3 setup where master is in default-ns and
each slave is into different (slave) ns. In this setup egress
packet processing for traffic originating from slave-ns will
hit all NF_HOOKs in slave-ns as well as default-ns. However same
is not true for ingress processing. All these NF_HOOKs are
hit only in the slave-ns skipping them in the default-ns.
IPvlan in L3 mode is restrictive and if admins want to deploy
iptables rules in default-ns, this asymmetric data path makes it
impossible to do so.

This patch makes use of the l3_rcv() (added as part of l3mdev
enhancements) to perform input route lookup on RX packets without
changing the skb->dev and then uses nf_hook at NF_INET_LOCAL_IN
to change the skb->dev just before handing over skb to L4.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
CC: David Ahern <dsa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add _nf_register_hooks() and _nf_unregister_hooks() calls which allow
caller to hold RTNL mutex.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
CC: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make ip6_route_input_lookup available outside of ipv6 the module
similar to ip_route_input_noref in the IPv4 world.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
net: return offloaded stats as default and expose original sw stats

The problem we try to handle is about offloaded forwarded packets
which are not seen by kernel. Let me try to draw it:

    port1                       port2 (HW stats are counted here)
      \                          /
       \                        /
        \                      /
         --(A)---- ASIC --(B)--
                    |
                   (C)
                    |
                   CPU (SW stats are counted here)

Now we have couple of flows for TX and RX (direction does not matter here):

1) port1->A->ASIC->C->CPU

   For this flow, HW and SW stats are equal.

2) port1->A->ASIC->C->CPU->C->ASIC->B->port2

   For this flow, HW and SW stats are equal.

3) port1->A->ASIC->B->port2

   For this flow, SW stats are 0.

The purpose of this patchset is to provide facility for user to
find out the difference between flows 1+2 and 3. In other words, user
will be able to see the statistics for the slow-path (through kernel).

Also note that HW stats are what someone calls "accumulated" stats.
Every packet counted by SW is also counted by HW. Not the other way around.

As a default the accumulated stats (HW) will be exposed to user
so the userspace apps can react properly.

This patchset add the SW stats (flows 1+2) under offload related stats, so
in the future we can expose other offload related stat in a similar way.

---
v9->v10:
- patch 2/3
 - removed unnecessary ()s as pointed out by Nik
v8->v9:
- patch 2/3
 - add using of idxattr and prividx
v7->v8:
- patch 2/3
 - move helping const from uapi to rtnetlink
 - cancel driver xstat nesting if it is empty
v6->v7:
- patch 1/3:
 - ndo interface changed to get the wanted stats type as an input.
 - change commit message.
- patch 2/3:
 - create a nesting for offloaded stat and put SW stats under it.
 - change the ndo call to indicate which offload stats we wants.
 - change commit message.
- patch 3/3:
 - change ndo implementation to match the changes in the previous patches.
 - change commit message.
v5->v6:
- patch 2/4 was dropped as requested by Roopa
- patch 1/3:
 - comment changed to indicate that default stats are combined stats
 - commit massage changed
- patch 2/3: (previously 3/4)
 - SW stats return nothing if there is no SW stats ndo
v4->v5:
- updated cover letter
- patch3/4:
  - using memcpy directly to copy stats as requested by DaveM
v3->v4:
- patch1/4:
  - fixed "return ()" pointed out by EricD
- patch2/4:
  - fixed if_nlmsg_size as pointed out by EricD
v2->v3:
- patch1/4:
  - added dev_have_sw_stats helper
- patch2/4:
  - avoided memcpy as requested by DaveM
- patch3/4:
  - use new dev_have_sw_stats helper
v1->v2:
- patch3/4:
  - fixed NULL initialization
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Change the default statistics ndo to return HW statistics
(like the one returned by ethtool_ops).
The HW stats are collected to a cache by delayed work every 1 sec.
Implement the offload stat ndo.
Add a function to get SW statistics, to be called from this function.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a nested attribute of offload stats to if_stats_msg
named IFLA_STATS_LINK_OFFLOAD_XSTATS.
Under it, add SW stats, meaning stats only per packets that went via
slowpath to the cpu, named IFLA_OFFLOAD_XSTATS_CPU_HIT.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new ndo to return statistics for offloaded operation.
Since there can be many different offloaded operation with many
stats types, the ndo gets an attribute id by which it knows which
stats are wanted. The ndo also gets a void pointer to be cast according
to the attribute id.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-next-for-davem-2016-09-16' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
This time we have various things - all across the board:
 * MU-MIMO sniffer support in mac80211
 * a create_singlethread_workqueue() cleanup
 * interface dump filtering that was documented but not implemented
 * support for the new radiotap timestamp field
 * send delBA in two unexpected conditions (as required by the spec)
 * connect keys cleanups - allow only WEP with index 0-3
 * per-station aggregation limit to work around broken APs
 * debugfs improvement for the integrated codel algorithm
and various other small improvements and cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

A couple of dev_err messages span two lines and the literal
string is missing a white space between words. Add the white
space and join the two lines into one.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: FLorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When fq is used on 32bit kernels, we need to lock the qdisc before
copying 64bit fields.

Otherwise "tc -s qdisc ..." might report bogus values.

Fixes: afe4fd06 ("pkt_sched: fq: Fair Queue packet scheduler")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of using flow stats per NUMA node, use it per CPU. When using
megaflows, the stats lock can be a bottleneck in scalability.

On a E5-2690 12-core system, usual throughput went from ~4Mpps to
~15Mpps when forwarding between two 40GbE ports with a single flow
configured on the datapath.

This has been tested on a system with possible CPUs 0-7,16-23. After
module removal, there were no corruption on the slab cache.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@redhat.com>
Cc: pravin shelar <pshelar@ovn.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

On a system with only node 1 as possible, all statistics is going to be
accounted on node 0 as it will have a single writer.

However, when getting and clearing the statistics, node 0 is not going
to be considered, as it's not a possible node.

Tested that statistics are not zero on a system with only node 1
possible. Also compile-tested with CONFIG_NUMA off.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@redhat.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Xin Long says:

====================
sctp: fix the transmit err process

This patchset is to improve the transmit err process and also fix some
issues.

After this patchset, once the chunks are enqueued successfully, even
if the chunks fail to send out, no matter because of nodst or nomem,
no err retruns back to users any more. Instead, they are taken care
of by retransmit.

v1->v2:
  - add more details to the changelog in patch 1/6
  - add Fixes: tag in patch 2/6, 3/6
  - also revert 69b5777f in patch 3/6
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

As David and Marcelo's suggestion, ENOMEM err shouldn't return back to
user in transmit path. Instead, sctp's retransmit would take care of
the chunks that fail to send because of ENOMEM.

This patch is only to do some release job when alloc_skb fails, not to
return ENOMEM back any more.

Besides, it also cleans up sctp_packet_transmit's err path, and fixes
some issues in err path:

 - It didn't free the head skb in nomem: path.
 - No need to check nskb in no_route: path.
 - It should goto err: path if alloc_skb fails for head.
 - Not all the NOMEMs should free nskb.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp_outq_flush return value is meaningless now, this patch is
to make sctp_outq_flush return void, as well as sctp_outq_fail
and sctp_outq_uncork.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Every time when sctp calls sctp_outq_flush, it sends out the chunks of
control queue, retransmit queue and data queue. Even if some trunks are
failed to transmit, it still has to flush all the transports, as it's
the only chance to clean that transmit_list.

So the latest transmit error here should be returned back. This transmit
error is an internal error of sctp stack.

I checked all the places where it uses the transmit error (the return
value of sctp_outq_flush), most of them are actually just save it to
sk_err.

Except for sctp_assoc/endpoint_bh_rcv, they will drop the chunk if
it's failed to send a REPLY, which is actually incorrect, as we can't
be sure the error that sctp_outq_flush returns is from sending that
REPLY.

So it's meaningless for sctp_outq_flush to return error back.

This patch is to save transmit error to sk_err in sctp_outq_flush, the
new error can update the old value. Eventually, sctp_wait_for_* would
check for it.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Last patch "sctp: do not return the transmit err back to sctp_sendmsg"
made sctp_primitive_SEND return err only when asoc state is unavailable.
In this case, chunks are not enqueued, they have no chance to be freed if
we don't take care of them later.

This Patch is actually to revert commit 1cd4d5c4 ("sctp: remove the
unused sctp_datamsg_free()"), commit 69b5777f ("sctp: hold the chunks
only after the chunk is enqueued in outq") and commit 8b570dc9 ("sctp:
only drop the reference on the datamsg after sending a msg"), to use
sctp_datamsg_free to free the chunks of current msg.

Fixes: 8b570dc9 ("sctp: only drop the reference on the datamsg after sending a msg")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Once a chunk is enqueued successfully, sctp queues can take care of it.
Even if it is failed to transmit (like because of nomem), it should be
put into retransmit queue.

If sctp report this error to users, it confuses them, they may resend
that msg, but actually in kernel sctp stack is in charge of retransmit
it already.

Besides, this error probably is not from the failure of transmitting
current msg, but transmitting or retransmitting another msg's chunks,
as sctp_outq_flush just tries to send out all transports' chunks.

This patch is to make sctp_cmd_send_msg return avoid, and not return the
transmit err back to sctp_sendmsg

Fixes: 8b570dc9 ("sctp: only drop the reference on the datamsg after sending a msg")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Data Chunks are only sent by sctp_primitive_SEND, in which sctp checks
the asoc's state through statetable before calling sctp_outq_tail. So
there's no need to check the asoc's state again in sctp_outq_tail.

Besides, sctp_do_sm is protected by lock_sock, even if sending msg is
interrupted by timer events, the event's processes still need to acquire
lock_sock first. It means no others CMDs can be enqueue into side effect
list before CMD_SEND_MSG to change asoc->state, so it's safe to remove it.

This patch is to remove redundant asoc->state check from sctp_outq_tail.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexei Starovoitov says:

====================
ip_tunnel: add collect_md mode to IPv4/IPv6 tunnels

Similar to geneve, vxlan, gre tunnels implement 'collect metadata' mode
in ipip, ipip6, ip6ip6 tunnels.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

the test creates 3 namespaces with veth connected via bridge.
First two namespaces simulate two different hosts with the same
IPv4 and IPv6 addresses configured on the tunnel interface and they
communicate with outside world via standard tunnels.
Third namespace creates collect_md tunnel that is driven by BPF
program which selects different remote host (either first or
second namespace) based on tcp dest port number while tcp dst
ip is the same.
This scenario is rough approximation of load balancer use case.
The tests check both traditional tunnel configuration and collect_md mode.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

extend existing tests for vxlan, geneve, gre to include IPIP tunnel.
It tests both traditional tunnel configuration and
dynamic via bpf helpers.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to gre, vxlan, geneve tunnels allow IPIP6 and IP6IP6 tunnels
to operate in 'collect metadata' mode.
Unlike ipv4 code here it's possible to reuse ip6_tnl_xmit() function
for both collect_md and traditional tunnels.
bpf_skb_[gs]et_tunnel_key() helpers and ovs (in the future) are the users.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to gre, vxlan, geneve tunnels allow IPIP tunnels to
operate in 'collect metadata' mode.
bpf_skb_[gs]et_tunnel_key() helpers can make use of it right away.
ovs can use it as well in the future (once appropriate ovs-vport
abstractions and user apis are added).
Note that just like in other tunnels we cannot cache the dst,
since tunnel_info metadata can be different for every packet.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check for net_device_ops structures that are only stored in the netdev_ops
field of a net_device structure.  This field is declared const, so
net_device_ops structures that have this property can be declared as const
also.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct net_device_ops i@p = { ... };

@ok@
identifier r.i;
struct net_device e;
position p;
@@
e.netdev_ops = &i@p;

@bad@
position p != {r.p,ok.p};
identifier r.i;
struct net_device_ops e;
@@
e@i@p

@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
 struct net_device_ops i = { ... };
// </smpl>

The result of size on this file before the change is:
   text	      data     bss     dec         hex	  filename
   3401        931      44    4376        1118	net/l2tp/l2tp_eth.o

and after the change it is:
   text	     data        bss	    dec	    hex	filename
   3993       347         44       4384    1120	net/l2tp/l2tp_eth.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check for net_device_ops structures that are only stored in the netdev_ops
field of a net_device structure.  This field is declared const, so
net_device_ops structures that have this property can be declared as const
also.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct net_device_ops i@p = { ... };

@ok@
identifier r.i;
struct net_device e;
position p;
@@
e.netdev_ops = &i@p;

@bad@
position p != {r.p,ok.p};
identifier r.i;
struct net_device_ops e;
@@
e@i@p

@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
 struct net_device_ops i = { ... };
// </smpl>

The result of size on this file before the change is:
   text	      data     bss     dec         hex	  filename
  21623       1316      40   22979        59c3
   drivers/net/ethernet/synopsys/dwc_eth_qos.o

and after the change it is:
   text	     data        bss	    dec	    hex	filename
  22199       724         40      22963    59b3
   drivers/net/ethernet/synopsys/dwc_eth_qos.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check for net_device_ops structures that are only stored in the netdev_ops
field of a net_device structure.  This field is declared const, so
net_device_ops structures that have this property can be declared as const
also.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct net_device_ops i@p = { ... };

@ok@
identifier r.i;
struct net_device e;
position p;
@@
e.netdev_ops = &i@p;

@bad@
position p != {r.p,ok.p};
identifier r.i;
struct net_device_ops e;
@@
e@i@p

@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
 struct net_device_ops i = { ... };
// </smpl>

The result of size on this file before the change is:

   text	      data     bss     dec         hex	  filename
   7995	       848       8    8851        2293
   drivers/net/ethernet/hisilicon/hip04_eth.o

and after the change it is:

   text	     data        bss	    dec	    hex	filename
   8571	      256          8       8835    2283
   drivers/net/ethernet/hisilicon/hip04_eth.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

(As asked by Dave in Februrary)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

No longer used after e0d56fdd ("net: l3mdev: remove redundant calls")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

No longer used after d66f6c0a ("net: ipv4: Remove l3mdev_get_saddr")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>