- 05 Feb, 2013 3 commits
-
-
Peter Huewe authored
With the previous patch 'Move duplicated code for dram to helper function' it becomes evident that the code is performing the same thing 4 or 8 times in a row without changing arguments to the function and thus writing the same values over and over again. It was tested that these repeats are unnecessary. -> we can safely remove them. Tested-by:
Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by:
Peter Huewe <peterhuewe@gmx.de> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Huewe authored
XGINew_SetDRAMDefaultRegister340 uses the same code fragment 4 times with only a slight variation each time. -> Move this code to a helper function - this saves some lines and ~450bytes in the .o / .ko Tested-by:
-
Peter Huewe authored
The XGI340_CR6B lookup table consists of the entries {0xaa, 0xaa, 0xaa, 0xaa} for an index <= 2 and {0x00, 0x00, 0x00, 0x00} for all other indices. The only user XGINew_SetDRAMDefaultRegister340 loops over these 4 values of a line with a for loop and since all entries are the same for each line we can simply replace the whole lookup table with a simple if/else assignment. Tested-by:
-
- 04 Feb, 2013 37 commits
-
-
H Hartley Sweeten authored
The (*detach) function, daq700_detach() is now a simple wrapper around comedi_pcmcia_disable(). Just use comedi_pcmcia_disable() directly for the (*detach). Signed-off-by:
H Hartley Sweeten <hsweeten@visionengravers.com> Cc: Ian Abbott <abbotti@mev.co.uk> Signed-off-by:
-
H Hartley Sweeten authored
Use the comedi_pcmcia_{enable,disable} helpers to enable/disable the PCMCIA device. This driver does not use interrupts and is not an audio device, remove CONF_ENABLE_IRQ and CONF_AUTO_AUDIO from the link->config_flags. Signed-off-by: -
H Hartley Sweeten authored
Use the comedi_pcmcia_{enable,disable} helpers to enable/disable the PCMCIA device. This driver does not use interrupts so remove CONF_ENABLE_IRQ from the link->config_flags. Signed-off-by: -
H Hartley Sweeten authored
The (*detach) function, das16cs_detach() is a simple wrapper around comedi_pcmcia_disable(). Just use comedi_pcmcia_disable() directly for the (*detach). Signed-off-by:
-
H Hartley Sweeten authored
Use pcmcia_request_irq() instead of request_irq() to request the irq for the PCMCIA device. This allows the PCMCIA core to clean up the registration in pcmcia_disable_device(). Signed-off-by:
-
H Hartley Sweeten authored
Use the comedi_pcmcia_{enable,disable} helpers to enable/disable the PCMCIA device. Signed-off-by: -
H Hartley Sweeten authored
Introduce some helper functions to enable/disable the PCMCIA device. This will allow removing some of the boilerplate code in the comedi PCMCIA drivers. Signed-off-by:
-
Peter Huewe authored
This patch simplifies the code of XGISetModeNew by reordering the if/else if/case conditions when both branches are doing exactly the same. Signed-off-by:
-
Peter Huewe authored
These two functions share the same code except one line - thus we can simply merge them and add a parameter to switch between both variants. Signed-off-by:
-
Peter Huewe authored
Since data can only be 0x0000, 0x0035 or 0x0048 we can simply skip the bit shifting and masking as data & 0xFF is always equal to data and data & 0xFF00 is always 0. So we simply use data and 0 directly and save the assignment. Signed-off-by:
-
Peter Huewe authored
Instead of subtracting one and then assign a different name and add 1 again we simply use HDE directly. HDE wasn't used directly before, so no change in functionality. Same applies to VDE. -> now we can remove the variable with the very descriptive name E ;) Signed-off-by:
-
Peter Huewe authored
We don't need to use this switch-case here for a simple two case if-else. Signed-off-by:
-
Peter Huewe authored
Since SR[0] in the (readonly) XGI330_StandTable is always 0x01 we can skip or'ing with 0x01 and make the code simpler by removing the if statements. Since this function is the only user of the XGI330_StandTable we can also include the unconditional |= 0x20 into the input data and move the assignment to SR1 into the loop, which I prefer to start at 0. Signed-off-by:
-
Peter Huewe authored
Clang warning: drivers/staging/xgifb/XGI_main_26.c: warning: variable 'ret' is used uninitialized whenever 'if' condition: if (xgifb_info->mode_idx < 0) { evaluates to true. drivers/staging/xgifb/XGI_main_26.c: note: uninitialized use occurs here return ret; This patch initializes the variable in this case. Signed-off-by: -
Peter Huewe authored
The mttr field must be declared as signed int (as in every other fb driver) for the mttr functions to work properly. Moreover the value should be initialized with -1. Signed-off-by:
-
Peter Huewe authored
This patch removes some comparisons that always evaluate to false since xoffset and yoffset are defined as __u32 in fb_var_screeninfo in include/linux/fb.h and thus can never be negative. Signed-off-by:
-
Peter Huewe authored
Since the smaller LCDRefreshIndex is contained identically in LCDARefreshIndex we can simply use LCDARefreshIndex and skip the if/else. Since LCDARefreshIndex is only used readonly and contains only small unsigned values we also change its declaration to const u8. In order to prevent an out-of-bounds access I changed the mask from 0x0F to 0x07 and added a dummy value. Signed-off-by:
-
Minchan Kim authored
1) User of zram normally do mkfs.xxx or mkswap before using the zram block device(ex, normally, do it at booting time) It ends up allocating such metadata of zram before real usage so benefit of lazy initialzation would be mitigated. 2) Some user want to use zram when memory pressure is high.(ie, load zram dynamically, NOT booting time). It does make sense because people don't want to waste memory until memory pressure is high(ie, where zram is really helpful time). In this case, lazy initialzation could be failed easily because we will use GFP_NOIO instead of GFP_KERNEL for avoiding deadlock. So the benefit of lazy initialzation would be mitigated, too. 3) Metadata overhead is not critical and Nitin has a plan to diet it. 4K : 12 byte(64bit machine) -> 64G : 192M so 0.3% isn't big overhead If insane user use such big zram device up to 20, it could consume 6% of ram but efficieny of zram will cover the waste. So this patch gives up lazy initialization and instead we initialize metadata at disksize setting time. Acked-by:
Jerome Marchand <jmarchand@redhat.com> Acked-by:
Nitin Gupta <ngupta@vflare.org> Signed-off-by:
Minchan Kim <minchan@kernel.org> Signed-off-by:
-
Minchan Kim authored
Now zram document syas "set disksize is optional" but partly it's wrong. When you try to use zram firstly after booting, you must set disksize, otherwise zram can't work because zram gendisk's size is 0. But once you do it, you can use zram freely after reset because reset doesn't reset to zero paradoxically. So in this time, disksize setting is optional.:( It's inconsitent for user behavior and not straightforward. This patch forces always setting disksize firstly before using zram. Yes. It changes current behavior so someone could complain when he upgrades zram. Apparently it could be a problem if zram is mainline but it still lives in staging so behavior could be changed for right way to go. Let them excuse. Acked-by:
Dan Magenheimer <dan.magenheimer@oracle.com> Signed-off-by:
-
Minchan Kim authored
Now zram allocates new page with GFP_KERNEL in zram I/O path if IO is partial. Unfortunately, It may cause deadlock with reclaim path like below. write_page from fs fs_lock allocation(GFP_KERNEL) reclaim pageout write_page from fs fs_lock <-- deadlock This patch fixes it by using GFP_NOIO. In read path, we reorganize code flow so that kmap_atomic is called after the GFP_NOIO allocation. Cc: stable@vger.kernel.org Acked-by:
Pekka Enberg <penberg@kernel.org> Signed-off-by:
-
H Hartley Sweeten authored
There are a number of pci vendor ids that are used in multiple drivers in the comedi subsystem. Move these ids to pci_ids.h. This also fixes some build warnings reported by the kbuild test robot about PCI_VENDOR_ID_AMPLICON being undeclared. Signed-off-by:
-
Ian Abbott authored
Tuomas <tvainikk _at_ gmail _dot_ com> reported problems getting meaningful output from a Lab-PC+ in differential mode for AI cmds, but AI insn reads gave correct readings. He tracked it down to two problems, one of which is addressed by this patch. It seems the setting of the channel bits for particular scanning modes was incorrect for differential mode. (Only half the number of channels are available in differential mode; comedi refers to them as channels 0, 1, 2 and 3, but the hardware documentation refers to them as channels 0, 2, 4 and 6.) In differential mode, the setting of the channel enable bits in the command1 register should depend on whether the scan enable bit is set. Effectively, we need to double the comedi channel number when the scan enable bit is not set in differential mode. The scan enable bit gets set when the AI scan mode is `MODE_MULT_CHAN_UP` or `MODE_MULT_CHAN_DOWN`, and gets cleared when the AI scan mode is `MODE_SINGLE_CHAN` or `MODE_SINGLE_CHAN_INTERVAL`. The existing test for whether the comedi channel number needs to be doubled in differential mode is incorrect in `labpc_ai_cmd()`. This patch corrects the test. Thanks to Tuomas for suggesting the fix. Signed-off-by:
Ian Abbott <abbotti@mev.co.uk> Cc: <stable@vger.kernel.org> # 3.7.x, 3.8.x Signed-off-by:
-
Ian Abbott authored
Tuomas <tvainikk _at_ gmail _dot_ com> reported problems getting meaningful output from a Lab-PC+ in differential mode for AI cmds, but AI insn reads gave correct readings. He tracked it down to two problems, one of which is addressed by this patch. It seems that writing to the command3 register after writing to the command4 register in `labpc_ai_cmd()` messes up the differential reference bit setting in the command4 register. Set up the command4 register after the command3 register (as in `labpc_ai_rinsn()`) to avoid the problem. Thanks to Tuomas for suggesting the fix. Signed-off-by:
-
Ian Abbott authored
Don't allow comedi drivers to change `dev->hw_dev` using `comedi_set_hw_dev()` if it's already been set. Return `-EEXIST` in that case. `dev->hw_dev` needs to be set to NULL by the core during clean-up of the comedi device, so add a local function `comedi_clear_hw_dev()` to do that. Signed-off-by:
-
Ian Abbott authored
Chnage the inline `comedi_set_hw_dev()` to an exported function and change it's return type from `void` to `int` so we can impose some restrictions (in a later patch) and return an error if necessary. Only a few comedi drivers call this, although they don't need to if the hardware device has been attached automatically via `comedi_auto_config()` and the comedi driver's `auto_attach()` method. Signed-off-by:
-
Ian Abbott authored
`comedi_alloc_subdevice_minor()` doesn't really need a parameter pointing to a `struct comedi_device` as it can get this information from the parameter pointing to a `struct comedi_subdevice`. Just pass the subdevice parameter. Signed-by:
-
Ian Abbott authored
Move the declarations of `comedi_alloc_subdevice_minor()` and `comedi_free_subdevice_minor()` from "comedidev.h" to "comedi_internal.h" since they are only of interest to the comedi core, and are not exported to the low-level comedi drivers. Signed-off-by:
-
Garrick He authored
Fix all 'please, no space before tabs' warning found by checkpatch.pl Signed-off-by:
Garrick He <garrickhe@gmail.com> Signed-off-by:
-
H Hartley Sweeten authored
Split the bus specific ISA/PC-104 and PCI code out of this driver and create two new drivers, das08_isa and das08_pci. This allows removing all the #ifdef'ery in the das08 driver that handled if the CONFIG_COMEDI_DAS08_{ISA,PCI} options were enabled. It also makes the PCI driver cleanly Plug-and-Play since the comedi driver only has an auto_attach callback. Previously it also had an attach callback in order to handle the ISA cards. Since the PCMCIA support was already split out, we can also remove the now unused enum das08_bustype and it's use in the boardinfo. The bus specific code deals with the bustype automatically before it calls the common attach function in das08. Signed-off-by: -
Andres More authored
Resolved 'do not use C99 // comments' checkpatch errors. Many warnings about odd indentation were left. Signed-off-by:
Andres More <more.andres@gmail.com> Signed-off-by:
-
Andres More authored
Cleared 'do not use C99 // comments' checkpatch error in device.h and device_cfg.h Signed-off-by:
-
Andres More authored
Cleared 'do not use C99 // comments' checkpatch error, several warnings about code indentation and camel casing were not resolved. Signed-off-by:
-
Andres More authored
Cleared 'do not use C99 // comments' checkpatch errors in two headers. Several obvious comments were removed. Signed-off-by:
-
Andres More authored
Switched // comments into respective /**/ ones Signed-off-by:
-
Andres More authored
switched all // comments on file to respective /**/ Signed-off-by:
-
H Hartley Sweeten authored
Convert this pcmcia driver to the comedi auto attach mechanism. This allows getting rid of the "hack" needed to pass the pcmcia_device pointer from the pcmcia_driver to the comedi_driver. We still need the boardinfo because ni_mio_common.c uses it. Cleanup ni_getboardtype() so it returns a pointer to the boardinto instead of the index. Signed-off-by:
-
H Hartley Sweeten authored
Convert this pcmcia driver to the comedi auto attach mechanism. This allows getting rid of the "hack" needed to pass the pcmcia_device pointer from the pcmcia_driver to the comedi_driver. We still need the boardinfo because the ni_labpc driver uses it. But we can get rid of the duplicate that allowed attaching with the driver name. Signed-off-by:
-
