- 16 Mar, 2017 40 commits
-
-
Eric Dumazet authored
commit 7cfd5fd5 upstream. On 32bit arches, (skb->end - skb->data) is not 'unsigned int', so we shall use min_t() instead of min() to avoid a compiler error. Fixes: 1272ce87 ("gro: Enter slow-path if there is no tailroom") Reported-by:
kernel test robot <fengguang.wu@intel.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net> [bwh: Backported to 3.2: adjust context] Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
Johan Hovold authored
commit 2d5a9c72 upstream. A short control transfer would currently fail to be detected, something which could lead to stale buffer data being used as valid input. Check for short transfers, and make sure to log any transfer errors. Note that this also avoids leaking heap data to user space (TIOCMGET) and the remote device (break control). Fixes: 6ce76104 ("USB: Driver for CH341 USB-serial adaptor") Signed-off-by:
Johan Hovold <johan@kernel.org> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Augusto Mecking Caringi authored
commit c8a6a09c upstream. In ca91cx42_slave_get function, the value pointed by vme_base pointer is set through: *vme_base = ioread32(bridge->base + CA91CX42_VSI_BS[i]); So it must be dereferenced to be used in calculation of pci_base: *pci_base = (dma_addr_t)*vme_base + pci_offset; This bug was caught thanks to the following gcc warning: drivers/vme/bridges/vme_ca91cx42.c: In function ‘ca91cx42_slave_get’: drivers/vme/bridges/vme_ca91cx42.c:467:14: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast] *pci_base = (dma_addr_t)vme_base + pci_offset; Signed-off-by:
Augusto Mecking Caringi <augustocaringi@gmail.com> Acked-By:
Martyn Welch <martyn@welchs.me.uk> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.2: adjust filename] Signed-off-by:
-
Akinobu Mita authored
commit 802c0388 upstream. The sysrq input handler should be attached to the input device which has a left alt key. On 32-bit kernels, some input devices which has a left alt key cannot attach sysrq handler. Because the keybit bitmap in struct input_device_id for sysrq is not correctly initialized. KEY_LEFTALT is 56 which is greater than BITS_PER_LONG on 32-bit kernels. I found this problem when using a matrix keypad device which defines a KEY_LEFTALT (56) but doesn't have a KEY_O (24 == 56%32). Cc: Jiri Slaby <jslaby@suse.com> Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Acked-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Eric Ren authored
commit e7ee2c08 upstream. The crash happens rather often when we reset some cluster nodes while nodes contend fiercely to do truncate and append. The crash backtrace is below: dlm: C21CBDA5E0774F4BA5A9D4F317717495: dlm_recover_grant 1 locks on 971 resources dlm: C21CBDA5E0774F4BA5A9D4F317717495: dlm_recover 9 generation 5 done: 4 ms ocfs2: Begin replay journal (node 318952601, slot 2) on device (253,18) ocfs2: End replay journal (node 318952601, slot 2) on device (253,18) ocfs2: Beginning quota recovery on device (253,18) for slot 2 ocfs2: Finishing quota recovery on device (253,18) for slot 2 (truncate,30154,1):ocfs2_truncate_file:470 ERROR: bug expression: le64_to_cpu(fe->i_size) != i_size_read(inode) (truncate,30154,1):ocfs2_truncate_file:470 ERROR: Inode 290321, inode i_size = 732 != di i_size = 937, i_flags = 0x1 ------------[ cut here ]------------ kernel BUG at /usr/src/linux/fs/ocfs2/file.c:470! invalid opcode: 0000 [#1] SMP Modules linked in: ocfs2_stack_user(OEN) ocfs2(OEN) ocfs2_nodemanager ocfs2_stackglue(OEN) quota_tree dlm(OEN) configfs fuse sd_mod iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi af_packet iscsi_ibft iscsi_boot_sysfs softdog xfs libcrc32c ppdev parport_pc pcspkr parport joydev virtio_balloon virtio_net i2c_piix4 acpi_cpufreq button processor ext4 crc16 jbd2 mbcache ata_generic cirrus virtio_blk ata_piix drm_kms_helper ahci syscopyarea libahci sysfillrect sysimgblt fb_sys_fops ttm floppy libata drm virtio_pci virtio_ring uhci_hcd virtio ehci_hcd usbcore serio_raw usb_common sg dm_multipath dm_mod scsi_dh_rdac scsi_dh_emc scsi_dh_alua scsi_mod autofs4 Supported: No, Unsupported modules are loaded CPU: 1 PID: 30154 Comm: truncate Tainted: G OE N 4.4.21-69-default #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.8.1-0-g4adadbd-20151112_172657-sheep25 04/01/2014 task: ffff88004ff6d240 ti: ffff880074e68000 task.ti: ffff880074e68000 RIP: 0010:[<ffffffffa05c8c30>] [<ffffffffa05c8c30>] ocfs2_truncate_file+0x640/0x6c0 [ocfs2] RSP: 0018:ffff880074e6bd50 EFLAGS: 00010282 RAX: 0000000000000074 RBX: 000000000000029e RCX: 0000000000000000 RDX: 0000000000000001 RSI: 0000000000000246 RDI: 0000000000000246 RBP: ffff880074e6bda8 R08: 000000003675dc7a R09: ffffffff82013414 R10: 0000000000034c50 R11: 0000000000000000 R12: ffff88003aab3448 R13: 00000000000002dc R14: 0000000000046e11 R15: 0000000000000020 FS: 00007f839f965700(0000) GS:ffff88007fc80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 00007f839f97e000 CR3: 0000000036723000 CR4: 00000000000006e0 Call Trace: ocfs2_setattr+0x698/0xa90 [ocfs2] notify_change+0x1ae/0x380 do_truncate+0x5e/0x90 do_sys_ftruncate.constprop.11+0x108/0x160 entry_SYSCALL_64_fastpath+0x12/0x6d Code: 24 28 ba d6 01 00 00 48 c7 c6 30 43 62 a0 8b 41 2c 89 44 24 08 48 8b 41 20 48 c7 c1 78 a3 62 a0 48 89 04 24 31 c0 e8 a0 97 f9 ff <0f> 0b 3d 00 fe ff ff 0f 84 ab fd ff ff 83 f8 fc 0f 84 a2 fd ff RIP [<ffffffffa05c8c30>] ocfs2_truncate_file+0x640/0x6c0 [ocfs2] It's because ocfs2_inode_lock() get us stale LVB in which the i_size is not equal to the disk i_size. We mistakenly trust the LVB because the underlaying fsdlm dlm_lock() doesn't set lkb_sbflags with DLM_SBF_VALNOTVALID properly for us. But, why? The current code tries to downconvert lock without DLM_LKF_VALBLK flag to tell o2cb don't update RSB's LVB if it's a PR->NULL conversion, even if the lock resource type needs LVB. This is not the right way for fsdlm. The fsdlm plugin behaves different on DLM_LKF_VALBLK, it depends on DLM_LKF_VALBLK to decide if we care about the LVB in the LKB. If DLM_LKF_VALBLK is not set, fsdlm will skip recovering RSB's LVB from this lkb and set the right DLM_SBF_VALNOTVALID appropriately when node failure happens. The following diagram briefly illustrates how this crash happens: RSB1 is inode metadata lock resource with LOCK_TYPE_USES_LVB; The 1st round: Node1 Node2 RSB1: PR RSB1(master): NULL->EX ocfs2_downconvert_lock(PR->NULL, set_lvb==0) ocfs2_dlm_lock(no DLM_LKF_VALBLK) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - dlm_lock(no DLM_LKF_VALBLK) convert_lock(overwrite lkb->lkb_exflags with no DLM_LKF_VALBLK) RSB1: NULL RSB1: EX reset Node2 dlm_recover_rsbs() recover_lvb() /* The LVB is not trustable if the node with EX fails and * no lock >= PR is left. We should set RSB_VALNOTVALID for RSB1. */ if(!(kb_exflags & DLM_LKF_VALBLK)) /* This means we miss the chance to return; * to invalid the LVB here. */ The 2nd round: Node 1 Node2 RSB1(become master from recovery) ocfs2_setattr() ocfs2_inode_lock(NULL->EX) /* dlm_lock() return the stale lvb without setting DLM_SBF_VALNOTVALID */ ocfs2_meta_lvb_is_trustable() return 1 /* so we don't refresh inode from disk */ ocfs2_truncate_file() mlog_bug_on_msg(disk isize != i_size_read(inode)) /* crash! */ The fix is quite straightforward. We keep to set DLM_LKF_VALBLK flag for dlm_lock() if the lock resource type needs LVB and the fsdlm plugin is uesed. Link: http://lkml.kernel.org/r/1481275846-6604-1-git-send-email-zren@suse.comSigned-off-by:
Eric Ren <zren@suse.com> Reviewed-by:
Joseph Qi <jiangqi903@gmail.com> Cc: Mark Fasheh <mfasheh@versity.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Herbert Xu authored
commit 57ea52a8 upstream. The GRO fast path caches the frag0 address. This address becomes invalid if frag0 is modified by pskb_may_pull or its variants. So whenever that happens we must disable the frag0 optimization. This is usually done through the combination of gro_header_hard and gro_header_slow, however, the IPv6 extension header path did the pulling directly and would continue to use the GRO fast path incorrectly. This patch fixes it by disabling the fast path when we enter the IPv6 extension header path. Fixes: 78a478d0 ("gro: Inline skb_gro_header and cache frag0 virtual address") Reported-by:
Slava Shwartsman <slavash@mellanox.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Herbert Xu authored
commit 1272ce87 upstream. The GRO path has a fast-path where we avoid calling pskb_may_pull and pskb_expand by directly accessing frag0. However, this should only be done if we have enough tailroom in the skb as otherwise we'll have to expand it later anyway. This patch adds the check by capping frag0_len with the skb tailroom. Fixes: cb18978c ("gro: Open-code final pskb_may_pull") Reported-by:
-
Mark Rutland authored
commit ddc37832 upstream. On APQ8060, the kernel crashes in arch_hw_breakpoint_init, taking an undefined instruction trap within write_wb_reg. This is because Scorpion CPUs erroneously appear to set DBGPRSR.SPD when WFI is issued, even if the core is not powered down. When DBGPRSR.SPD is set, breakpoint and watchpoint registers are treated as undefined. It's possible to trigger similar crashes later on from userspace, by requesting the kernel to install a breakpoint or watchpoint, as we can go idle at any point between the reset of the debug registers and their later use. This has always been the case. Given that this has always been broken, no-one has complained until now, and there is no clear workaround, disable hardware breakpoints and watchpoints on Scorpion to avoid these issues. Signed-off-by:
Mark Rutland <mark.rutland@arm.com> Reported-by:
Linus Walleij <linus.walleij@linaro.org> Reviewed-by:
Stephen Boyd <sboyd@codeaurora.org> Acked-by:
Will Deacon <will.deacon@arm.com> Cc: Russell King <linux@armlinux.org.uk> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> [bwh: Backported to 3.2: - Open-code read_cpuid_part() - Adjust context] Signed-off-by:
-
Johan Hovold authored
commit 55fa15b5 upstream. Revert to using direct register writes to set the divisor and line-control registers. A recent change switched to using the init vendor command to update these registers, something which also enabled support for CH341A devices. It turns out that simply setting bit 7 in the divisor register is sufficient to support CH341A and specifically prevent data from being buffered until a full endpoint-size packet (32 bytes) has been received. Using the init command also had the side-effect of temporarily deasserting the DTR/RTS signals on every termios change (including initialisation on open) something which for example could cause problems in setups where DTR is used to trigger a reset. Fixes: 4e46c410 ("USB: serial: ch341: reinitialize chip on reconfiguration") Signed-off-by:
-
Johan Hovold authored
commit ce5e2928 upstream. Fix reset-resume handling which failed to resubmit the read and interrupt URBs, thereby leaving a port that was open before suspend in a broken state until closed and reopened. Fixes: 1ded7ea4 ("USB: ch341 serial: fix port number changed after resume") Fixes: 2bfd1c96 ("USB: serial: ch341: remove reset_resume callback") Signed-off-by:
-
Johan Hovold authored
commit f2950b78 upstream. Make sure to stop the interrupt URB before returning on errors during open. Fixes: 664d5df9 ("USB: usb-serial ch341: support for DTR/RTS/CTS") Signed-off-by:
-
Johan Hovold authored
commit 030ee7ae upstream. The modem-control signals are managed by the tty-layer during open and should not be asserted prematurely when set_termios is called from driver open. Also make sure that the signals are asserted only when changing speed from B0. Fixes: 664d5df9 ("USB: usb-serial ch341: support for DTR/RTS/CTS") Signed-off-by:
-
Johan Hovold authored
commit a20047f3 upstream. The private baud_rate variable is used to configure the port at open and reset-resume and must never be set to (and left at) zero or reset-resume and all further open attempts will fail. Fixes: aa91def4 ("USB: ch341: set tty baud speed according to tty struct") Fixes: 664d5df9 ("USB: usb-serial ch341: support for DTR/RTS/CTS") Signed-off-by:
-
Johan Hovold authored
commit 4e2da446 upstream. DTR and RTS will be asserted by the tty-layer when the port is opened and deasserted on close (if HUPCL is set). Make sure the initial state is not-asserted before the port is first opened as well. Fixes: 664d5df9 ("USB: usb-serial ch341: support for DTR/RTS/CTS") Signed-off-by:
-
Aidan Thornton authored
commit 4e46c410 upstream. Changing the LCR register after initialization does not seem to be reliable on all chips (particularly not on CH341A). Restructure initialization and configuration to always reinit the chip on configuration changes instead and pass the LCR register value directly to the initialization command. (Note that baud rates above 500kbaud are incorrect, but they're incorrect in the same way both before and after this patch at least on the CH340G. Fixing this isn't a priority as higher baud rates don't seem that reliable anyway.) Cleaned-up version of a patch by Grigori Goronzy Signed-off-by:
Aidan Thornton <makosoft@gmail.com> Reviewed-by:
Grigori Goronzy <greg@chown.ath.cx> Signed-off-by:
-
Aidan Thornton authored
commit 6fde8d29 upstream. No functional changes, this just gives names to some registers and USB requests based on Grigori Goronzy's work and WinChipTech's Linux driver (which reassuringly agree), then uses them in place of magic numbers. This also renames the misnamed BREAK2 register (actually UART config) Signed-off-by:
-
Nicolas PLANEL authored
commit aa91def4 upstream. The ch341_set_baudrate() function initialize the device baud speed according to the value on priv->baud_rate. By default the ch341_open() set it to a hardcoded value (DEFAULT_BAUD_RATE 9600). Unfortunately, the tty_struct is not initialized with the same default value. (usually 56700) This means that the tty_struct and the device baud rate generator are not synchronized after opening the port. Fixup is done by calling ch341_set_termios() if tty exist. Remove unnecessary variable priv->baud_rate setup as it's already done by ch341_port_probe(). Remove unnecessary call to ch341_set_{handshake,baudrate}() in ch341_open() as there already called in ch341_configure() and ch341_set_termios() Signed-off-by:
Nicolas PLANEL <nicolas.planel@enovance.com> Signed-off-by:
-
Johan Hovold authored
commit 394a1033 upstream. Remove redundant call to ch341_close from error path when submission of the interrupt urb fails in open. Signed-off-by:
-
Johan Hovold authored
commit 06946a66 upstream. All error messages from stack in open are being forwarded except for one call to usb_submit_urb. Change this for consistency. Signed-off-by:
Johan Hovold <jhovold@gmail.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by:
-
Arvind Yadav authored
commit 064c3db9 upstream. Here, If devm_ioremap will fail. It will return NULL. Then hpriv->base = NULL - 0x20000; Kernel can run into a NULL-pointer dereference. This error check will avoid NULL pointer dereference. Signed-off-by:
Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Greg Kroah-Hartman authored
commit 1ebb7114 upstream. Make sure we have enough of a report structure to validate before looking at it. Reported-by:
Benoit Camredon <benoit.camredon@airbus.com> Tested-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Alan Stern authored
commit 0a8fd134 upstream. When checking a new device's descriptors, the USB core does not check for duplicate endpoint addresses. This can cause a problem when the sysfs files for those endpoints are created; trying to create multiple files with the same name will provoke a WARNING: WARNING: CPU: 2 PID: 865 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x8a/0xa0 sysfs: cannot create duplicate filename '/devices/platform/dummy_hcd.0/usb2/2-1/2-1:64.0/ep_05' Kernel panic - not syncing: panic_on_warn set ... CPU: 2 PID: 865 Comm: kworker/2:1 Not tainted 4.9.0-rc7+ #34 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Workqueue: usb_hub_wq hub_event ffff88006bee64c8 ffffffff81f96b8a ffffffff00000001 1ffff1000d7dcc2c ffffed000d7dcc24 0000000000000001 0000000041b58ab3 ffffffff8598b510 ffffffff81f968f8 ffffffff850fee20 ffffffff85cff020 dffffc0000000000 Call Trace: [< inline >] __dump_stack lib/dump_stack.c:15 [<ffffffff81f96b8a>] dump_stack+0x292/0x398 lib/dump_stack.c:51 [<ffffffff8168c88e>] panic+0x1cb/0x3a9 kernel/panic.c:179 [<ffffffff812b80b4>] __warn+0x1c4/0x1e0 kernel/panic.c:542 [<ffffffff812b8195>] warn_slowpath_fmt+0xc5/0x110 kernel/panic.c:565 [<ffffffff819e70ca>] sysfs_warn_dup+0x8a/0xa0 fs/sysfs/dir.c:30 [<ffffffff819e7308>] sysfs_create_dir_ns+0x178/0x1d0 fs/sysfs/dir.c:59 [< inline >] create_dir lib/kobject.c:71 [<ffffffff81fa1b07>] kobject_add_internal+0x227/0xa60 lib/kobject.c:229 [< inline >] kobject_add_varg lib/kobject.c:366 [<ffffffff81fa2479>] kobject_add+0x139/0x220 lib/kobject.c:411 [<ffffffff82737a63>] device_add+0x353/0x1660 drivers/base/core.c:1088 [<ffffffff82738d8d>] device_register+0x1d/0x20 drivers/base/core.c:1206 [<ffffffff82cb77d3>] usb_create_ep_devs+0x163/0x260 drivers/usb/core/endpoint.c:195 [<ffffffff82c9f27b>] create_intf_ep_devs+0x13b/0x200 drivers/usb/core/message.c:1030 [<ffffffff82ca39d3>] usb_set_configuration+0x1083/0x18d0 drivers/usb/core/message.c:1937 [<ffffffff82cc9e2e>] generic_probe+0x6e/0xe0 drivers/usb/core/generic.c:172 [<ffffffff82caa7fa>] usb_probe_device+0xaa/0xe0 drivers/usb/core/driver.c:263 This patch prevents the problem by checking for duplicate endpoint addresses during enumeration and skipping any duplicates. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-by:
Andrey Konovalov <andreyknvl@google.com> Tested-by:
-
Tony Lindgren authored
commit 8c300fe2 upstream. When unloading omap2430, we can get the following splat: WARNING: CPU: 1 PID: 295 at kernel/irq/manage.c:1478 __free_irq+0xa8/0x2c8 Trying to free already-free IRQ 4 ... [<c01a8b78>] (free_irq) from [<bf0aea84>] (musbhs_dma_controller_destroy+0x28/0xb0 [musb_hdrc]) [<bf0aea84>] (musbhs_dma_controller_destroy [musb_hdrc]) from [<bf09f88c>] (musb_remove+0xf0/0x12c [musb_hdrc]) [<bf09f88c>] (musb_remove [musb_hdrc]) from [<c056a384>] (platform_drv_remove+0x24/0x3c) ... This is because the irq number in use is 260 nowadays, and the dma controller is using u8 instead of int. Fixes: 6995eb68 ("USB: musb: enable low level DMA operation for Blackfin") Signed-off-by:
Tony Lindgren <tony@atomide.com> [b-liu@ti.com: added Fixes tag] Signed-off-by:
Bin Liu <b-liu@ti.com> Signed-off-by:
-
Lukasz Odzioba authored
commit dd853fd2 upstream. A negative number can be specified in the cmdline which will be used as setup_clear_cpu_cap() argument. With that we can clear/set some bit in memory predceeding boot_cpu_data/cpu_caps_cleared which may cause kernel to misbehave. This patch adds lower bound check to setup_disablecpuid(). Boris Petkov reproduced a crash: [ 1.234575] BUG: unable to handle kernel paging request at ffffffff858bd540 [ 1.236535] IP: memcpy_erms+0x6/0x10 Signed-off-by:
Lukasz Odzioba <lukasz.odzioba@intel.com> Acked-by:
Borislav Petkov <bp@suse.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: andi.kleen@intel.com Cc: bp@alien8.de Cc: dave.hansen@linux.intel.com Cc: luto@kernel.org Cc: slaoub@gmail.com Fixes: ac72e788 ("x86: add generic clearcpuid=... option") Link: http://lkml.kernel.org/r/1482933340-11857-1-git-send-email-lukasz.odzioba@intel.comSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Huang Rui authored
commit 432abf68 upstream. The generic command buffer entry is 128 bits (16 bytes), so the offset of tail and head pointer should be 16 bytes aligned and increased with 0x10 per command. When cmd buf is full, head = (tail + 0x10) % CMD_BUFFER_SIZE. So when left space of cmd buf should be able to store only two command, we should be issued one COMPLETE_WAIT additionally to wait all older commands completed. Then the left space should be increased after IOMMU fetching from cmd buf. So left check value should be left <= 0x20 (two commands). Signed-off-by:
Huang Rui <ray.huang@amd.com> Fixes: ac0ea6e9 ('x86/amd-iommu: Improve handling of full command buffer') Signed-off-by:
Joerg Roedel <jroedel@suse.de> Signed-off-by:
-
Johan Hovold authored
commit ef079936 upstream. Fix NULL-pointer dereference in open() should a malicious device lack the expected endpoints: Unable to handle kernel NULL pointer dereference at virtual address 00000030 .. [<bf06a6b0>] (ti_open [ti_usb_3410_5052]) from [<bf02e118>] (serial_port_activate+0x68/0x98 [usbserial]) Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Johan Hovold authored
commit cc090924 upstream. Fix NULL-pointer dereference in open() should the device lack the expected endpoints: Unable to handle kernel NULL pointer dereference at virtual address 00000030 ... PC is at spcp8x5_open+0x30/0xd0 [spcp8x5] Fixes: 619a6f1d ("USB: add usb-serial spcp8x5 driver") Signed-off-by:
-
Johan Hovold authored
commit 76ab439e upstream. Fix NULL-pointer dereference in open() should a type-0 or type-1 device lack the expected endpoints: Unable to handle kernel NULL pointer dereference at virtual address 00000030 ... PC is at pl2303_open+0x38/0xec [pl2303] Note that a missing interrupt-in endpoint would have caused open() to fail. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Johan Hovold authored
commit 5afeef23 upstream. Fix NULL-pointer dereference in open() should the device lack the expected endpoints: Unable to handle kernel NULL pointer dereference at virtual address 00000030 ... PC is at oti6858_open+0x30/0x1d0 [oti6858] Note that a missing interrupt-in endpoint would have caused open() to fail. Fixes: 49cdee0e ("USB: oti6858 usb-serial driver (in Nokia CA-42 cable)") Signed-off-by:
-
Johan Hovold authored
commit a5bc0194 upstream. Fix NULL-pointer dereferences at open() and disconnect() should the device lack the expected bulk-out endpoints: Unable to handle kernel NULL pointer dereference at virtual address 000000b4 ... [c0170ff0>] (__lock_acquire) from [<c0172f00>] (lock_acquire+0x108/0x264) [<c0172f00>] (lock_acquire) from [<c06a5090>] (_raw_spin_lock_irqsave+0x58/0x6c) [<c06a5090>] (_raw_spin_lock_irqsave) from [<c0470684>] (tty_port_tty_set+0x28/0xa4) [<c0470684>] (tty_port_tty_set) from [<bf08d384>] (omninet_open+0x30/0x40 [omninet]) [<bf08d384>] (omninet_open [omninet]) from [<bf07c118>] (serial_port_activate+0x68/0x98 [usbserial]) Unable to handle kernel NULL pointer dereference at virtual address 00000234 ... [<bf01f418>] (omninet_disconnect [omninet]) from [<bf0016c0>] (usb_serial_disconnect+0xe4/0x100 [usbserial]) Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Johan Hovold authored
commit 472d7e55 upstream. The interrupt URB is killed at final port close since commit 0de9a702 ("USB: overhaul of mos7840 driver"). Fixes: 0de9a702 ("USB: overhaul of mos7840 driver") Signed-off-by:
-
Johan Hovold authored
commit 5c75633e upstream. Fix NULL-pointer dereference in open() should the device lack the expected endpoints: Unable to handle kernel NULL pointer dereference at virtual address 00000030 ... PC is at mos7840_open+0x88/0x8dc [mos7840] Note that we continue to treat the interrupt-in endpoint as optional for now. Fixes: 3f542974 ("USB: Moschip 7840 USB-Serial Driver") Signed-off-by:
-
Johan Hovold authored
commit fde1faf8 upstream. A static usb-serial-driver structure that is used to initialise the interrupt URB was modified during probe depending on the currently probed device type, something which could break a parallel probe of a device of a different type. Fix this up by overriding the default completion callback for MCS7715 devices in attach() instead. We may want to use two usb-serial driver instances for the two types later. Fixes: fb088e33 ("USB: serial: add support for serial port on the moschip 7715") Signed-off-by:
-
Johan Hovold authored
commit 75dd211e upstream. Do not submit the interrupt URB until after the parport has been successfully registered to avoid another use-after-free in the completion handler when accessing the freed parport private data in case of a racing completion. Fixes: b69578df ("USB: usbserial: mos7720: add support for parallel port on moschip 7715") Signed-off-by:
-
Johan Hovold authored
commit 91a1ff4d upstream. The interrupt URB was submitted on probe but never stopped on probe errors. This can lead to use-after-free issues in the completion handler when accessing the freed usb-serial struct: Unable to handle kernel paging request at virtual address 6b6b6be7 ... [<bf052e70>] (mos7715_interrupt_callback [mos7720]) from [<c052a894>] (__usb_hcd_giveback_urb+0x80/0x140) [<c052a894>] (__usb_hcd_giveback_urb) from [<c052a9a4>] (usb_hcd_giveback_urb+0x50/0x138) [<c052a9a4>] (usb_hcd_giveback_urb) from [<c0550684>] (musb_giveback+0xc8/0x1cc) Fixes: b69578df ("USB: usbserial: mos7720: add support for parallel port on moschip 7715") Signed-off-by:
-
Johan Hovold authored
commit b05aebc2 upstream. Fix NULL-pointer dereference at port open if a device lacks the expected bulk in and out endpoints. Unable to handle kernel NULL pointer dereference at virtual address 00000030 ... [<bf071c20>] (mos7720_open [mos7720]) from [<bf0490e0>] (serial_port_activate+0x68/0x98 [usbserial]) [<bf0490e0>] (serial_port_activate [usbserial]) from [<c0470ca4>] (tty_port_open+0x9c/0xe8) [<c0470ca4>] (tty_port_open) from [<bf049d98>] (serial_open+0x48/0x6c [usbserial]) [<bf049d98>] (serial_open [usbserial]) from [<c0469178>] (tty_open+0xcc/0x5cc) Fixes: 0f64478c ("USB: add USB serial mos7720 driver") Signed-off-by:
-
Johan Hovold authored
commit 21ce5784 upstream. Fix NULL-pointer dereference in write() should the device lack the expected interrupt-out endpoint: Unable to handle kernel NULL pointer dereference at virtual address 00000054 ... PC is at kobil_write+0x144/0x2a0 [kobil_sct] Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Johan Hovold authored
commit 5d9b0f85 upstream. Check for the expected endpoints in attach() and fail loudly if not present. Note that failing to do this appears to be benign since da280e34 ("USB: keyspan_pda: clean up write-urb busy handling") which prevents a NULL-pointer dereference in write() by never marking a non-existent write-urb as free. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Johan Hovold authored
commit 90507d54 upstream. Fix NULL-pointer dereference at open should the device lack a bulk-in or bulk-out endpoint: Unable to handle kernel NULL pointer dereference at virtual address 00000030 ... PC is at iuu_open+0x78/0x59c [iuu_phoenix] Fixes: 07c3b1a1 ("USB: remove broken usb-serial num_endpoints check") Signed-off-by:
-
Johan Hovold authored
commit 4f9785cc upstream. In case a device is left in "boot-mode" we must not register any port devices in order to avoid a NULL-pointer dereference on open due to missing endpoints. This could be used by a malicious device to trigger an OOPS: Unable to handle kernel NULL pointer dereference at virtual address 00000030 ... [<bf0caa84>] (edge_open [io_ti]) from [<bf0b0118>] (serial_port_activate+0x68/0x98 [usbserial]) [<bf0b0118>] (serial_port_activate [usbserial]) from [<c0470ca4>] (tty_port_open+0x9c/0xe8) [<c0470ca4>] (tty_port_open) from [<bf0b0da0>] (serial_open+0x48/0x6c [usbserial]) [<bf0b0da0>] (serial_open [usbserial]) from [<c0469178>] (tty_open+0xcc/0x5cc) Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
