Add new flag to remember when route is via gateway.
We will use it to allow rt_gateway to contain address of
directly connected host for the cases when DST_NOCACHE is
used or when the NH exception caches per-destination route
without DST_NOCACHE flag, i.e. when routes are not used for
other destinations. By this way we force the neighbour
resolving to work with the routed destination but we
can use different address in the packet, feature needed
for IPVS-DR where original packet for virtual IP is routed
via route to real IP.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

Avoid checking nh_pcpu_rth_output in fast path,
abort fib_info creation on alloc_percpu failure.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

After the change "Adjust semantics of rt->rt_gateway"
(commit f8126f1d) rt_gateway can be 0 but ip_forward() compares
it directly with nexthop. What we want here is to check if traffic
is to directly connected nexthop and to fail if using gateway.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

After "Cache input routes in fib_info nexthops" (commit
d2d68ba9) and "Elide fib_validate_source() completely when possible"
(commit 7a9bc9b8) we can not send ICMP redirects. It seems we
should not cache the RTCF_DOREDIRECT flag in nh_rth_input because
the same fib_info can be used for traffic that is not redirected,
eg. from other input devices or from sources that are not in same subnet.

	As result, we have to disable the caching of RTCF_DOREDIRECT
flag and to force source validation for the case when forwarding
traffic to the input device. If traffic comes from directly connected
source we allow redirection as it was done before both changes.

	Avoid setting RTCF_DOREDIRECT if IN_DEV_TX_REDIRECTS
is disabled, this can avoid source address validation and to
help caching the routes.

	After the change "Adjust semantics of rt->rt_gateway"
(commit f8126f1d) we should make sure our ICMP_REDIR_HOST messages
contain daddr instead of 0.0.0.0 when target is directly connected.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

It seems IPV6_GRO_CB(skb)->proto can be destroyed in skb_gro_receive()
if a new skb is allocated (to serve as an anchor for frag_list)

We copy NAPI_GRO_CB() only (not the IPV6 specific part) in :

*NAPI_GRO_CB(nskb) = *NAPI_GRO_CB(p);

So we leave IPV6_GRO_CB(nskb)->proto to 0 (fresh skb allocation) instead
of IPPROTO_TCP (6)

ipv6_gro_complete() isnt able to call ops->gro_complete()
[ tcp6_gro_complete() ]

Fix this by moving proto in NAPI_GRO_CB() and getting rid of
IPV6_GRO_CB
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

6a32e4f9 made the vlan code skip marking
vlan-tagged frames for not locally configured vlans as PACKET_OTHERHOST if
there was an rx_handler, as the rx_handler could cause the frame to be received
on a different (virtual) vlan-capable interface where that vlan might be
configured.

As rx_handlers do not necessarily return RX_HANDLER_ANOTHER, this could cause
frames for unknown vlans to be delivered to the protocol stack as if they had
been received untagged.

For example, if an ipv6 router advertisement that's tagged for a locally not
configured vlan is received on an interface with macvlan interfaces attached,
macvlan's rx_handler returns RX_HANDLER_PASS after delivering the frame to the
macvlan interfaces, which caused it to be passed to the protocol stack, leading
to ipv6 addresses for the announced prefix being configured even though those
are completely unusable on the underlying interface.

The fix moves marking as PACKET_OTHERHOST after the rx_handler so the
rx_handler, if there is one, sees the frame unchanged, but afterwards,
before the frame is delivered to the protocol stack, it gets marked whether
there is an rx_handler or not.
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current GRO can hold packets in gro_list for almost unlimited
time, in case napi->poll() handler consumes its budget over and over.

In this case, napi_complete()/napi_gro_flush() are not called.

Another problem is that gro_list is flushed in non friendly way :
We scan the list and complete packets in the reverse order.
(youngest packets first, oldest packets last)
This defeats priorities that sender could have cooked.

Since GRO currently only store TCP packets, we dont really notice the
bug because of retransmits, but this behavior can add unexpected
latencies, particularly on mice flows clamped by elephant flows.

This patch makes sure no packet can stay more than 1 ms in queue, and
only in stress situations.

It also complete packets in the right order to minimize latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marvell 88E8001 on an ASUS P5NSLI motherboard is unable to send/receive
packets on a system with >4gb ram unless a 32bit DMA mask is used.

This issue has been around for years and a fix was sent 3.5 years ago, but
there was some debate as to whether it should instead be fixed as a PCI quirk.
http://www.spinics.net/lists/netdev/msg88670.html

However, 18 months later a similar workaround was introduced for another
chipset exhibiting the same problem.
http://www.spinics.net/lists/netdev/msg142287.htmlSigned-off-by: Graham Gower <graham.gower@gmail.com>
Signed-off-by: Jan Ceuleers <jan.ceuleers@computer.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes type assignment issues, function definition and symbol
shadowing which triggered sparse warnings.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We report cached pmtu values even if they are already expired.
Change this to not report these values after they are expired
and fix a race in the expire time calculation, as suggested by
Eric Dumazet.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a local tool like tracepath tries to send packets bigger than
the device mtu, we create a nh exeption and set the pmtu to device
mtu. The device mtu does not expire, so check if the device mtu is
smaller than the reported pmtu and don't crerate a nh exeption in
that case.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some protocols, like IPsec still cache routes. So we need to invalidate
the old route on pmtu events to avoid the reuse of stale routes.
We also need to update the mtu and expire time of the route if we already
use a nh exception route, otherwise we ignore newly learned pmtu values
after the first expiration.

With this patch we always invalidate or update the route on pmtu events.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MEMWIN0_APERTURE is the size in bytes.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Using list_move() instead of list_del() + list_add().

dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove including <linux/version.h> that don't need it.

dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before accessing skb first fragment, better make sure there
is one.

This is probably not needed for old kernels, since an ethernet frame
cannot contain only an ethernet header, but the recent GRO addition
to tunnels makes this patch needed.

Also skb_gro_reset_offset() can be static, it actually allows
compiler to inline it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

IPv4 side of the problem was addressed in commit a9e050f4
(net: tcp: GRO should be ECN friendly)

This patch does the same, but for IPv6 : A Traffic Class mismatch
doesnt mean flows are different, but instead should force a flush
of previous packets.

This patch removes artificial packet reordering problem.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

The retry loop in neigh_resolve_output() and neigh_connected_output()
call dev_hard_header() with out reseting the skb to network_header.
This causes the retry to fail with skb_under_panic. The fix is to
reset the network_header within the retry loop.
Signed-off-by: Ramesh Nagappa <ramesh.nagappa@ericsson.com>
Reviewed-by: Shawn Lu <shawn.lu@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Reviewed-by: Billie Alsup <billie.alsup@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function sky2_probe() return 0 for success and negative value
for most of its internal tests failures. There are two exceptions
that are error cases going to err_out*:. For this two cases, the
function abort its success execution path, but returns non negative
value, making it dificult for a caller function to notice the error.

This patch fixes the error cases that do not return negative values.

This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.

A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function skge_probe() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to err_out_led_off:. For this error case, the
function abort its success execution path, but returns non negative
value, making it difficult for a caller function to notice the error.

This patch fixes the error case that do not return negative value.

This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.

A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function gem_init_one() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to err_out_free_consistent:. For this error
case, the function abort its success execution path, but returns non
negative value, making it difficult for a caller function to notice
the error.

This patch fixes the error case that do not return negative value.

This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.

A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function niu_pci_init_one() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to err_out_free_res:. For this error case, the
function abort its success execution path, but returns non negative
value, making it difficult for a caller function to notice the error.

This patch fixes the error case that do not return negative value.

This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.

A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function sh_eth_drv_probe() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to out_release:. For this error case, the
function abort its success execution path, but returns non negative
value, making it difficult for a caller function to notice the error.

This patch fixes the error case that do not return negative value.

This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.

A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function sonic_probe1() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to out:. For this error case, the
function abort its success execution path, but returns non negative
value, making it difficult for a caller function to notice the error.

This patch fixes the error case that do not return negative value.

This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.

A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function au1000_probe() return 0 for success and negative value
for most of its internal tests failures. There are exceptions
that are error cases going to err_out:. For this cases, the
function abort its success execution path, but returns non negative
value, making it dificult for a caller function to notice the error.

This patch fixes the error cases that do not return negative values.

This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.

A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function amd8111e_probe_one() return 0 for success and negative
value for most of its internal tests failures. There are two exceptions
that are error cases going to err_free_reg:. For this two cases, the
function abort its success execution path, but returns non negative
value, making it dificult for a caller function to notice the error.

This patch fixes the error cases that do not return negative values.

This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.

A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function qlcnic_probe() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to err_out_free_netdev:. For this error case,
the function abort its success execution path, but returns non negative
value, making it difficult for a caller function to notice the error.

This patch fixes the error case that do not return negative value.

This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.

A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function sh_sir_probe() return 0 for success and negative value
for most of its internal tests failures. There are two exceptions
that are error cases going to err_mem_*:. For this two cases, the
function abort its success execution path, but returns non negative
value, making it dificult for a caller function to notice the error.

This patch fixes the error cases that do not return negative values.

This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.

A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function sh_irda_probe() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to err_mem_4:. For this error case, the
function abort its success execution path, but returns non negative
value, making it difficult for a caller function to notice the error.

This patch fixes the error case that do not return negative value.

This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.

A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function sa1100_irda_probe() return 0 for success and negative
value for most of its internal tests failures. There is one exception
that is error case going to err_mem_4:. For this error case, the
function abort its success execution path, but returns non negative
value, making it difficult for a caller function to notice the error.

This patch fixes the error case that do not return negative value.

This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.

A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function pxa_irda_probe() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to err_mem_3:. For this error case, the
function abort its success execution path, but returns non negative
value, making it difficult for a caller function to notice the error.

This patch fixes the error case that do not return negative value.

This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.

A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function mcs_probe() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to error2:. For this error case, the
function abort its success execution path, but returns non negative
value, making it difficult for a caller function to notice the error.

This patch fixes the error case that do not return negative value.

A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function irtty_open() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to out_put:. For this error case, the
function abort its success execution path, but returns non negative
value, making it difficult for a caller function to notice the error.

This patch fixes the error case that do not return negative value.

This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.

A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function sis900_probe() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to err_out_cleardev:. Fore this error case,
the function abort its success execution path, but returns non negative
value, making it difficult for a caller function to notice the error.

This patch fixes the error case that do not return negative value.

This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.

A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function natsemi_probe1() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to err_create_file:. Fore this error case the
function abort its success execution path, but returns non negative value,
making it difficult for a caller function to notice the error.

This patch fixes the error case that do not return negative value.

This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.

A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function dmfe_init_one() return 0 for success and negative value
for most of its internal tests failures. There are three exceptions
that are error cases going to err_out_*:. Fore this three cases the
function abort its success execution path, but returns non negative
value, making it dificult for a caller function to notice the error.

This patch fixes the error cases that do not return negative values.

This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.

A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Over time, skb recycling infrastructure got litle interest and
many bugs. Generic rx path skb allocation is now using page
fragments for efficient GRO / TCP coalescing, and recyling
a tx skb for rx path is not worth the pain.

Last identified bug is that fat skbs can be recycled
and it can endup using high order pages after few iterations.

With help from Maxime Bizon, who pointed out that commit
87151b86 (net: allow pskb_expand_head() to get maximum tailroom)
introduced this regression for recycled skbs.

Instead of fixing this bug, lets remove skb recycling.

Drivers wanting really hot skbs should use build_skb() anyway,
to allocate/populate sk_buff right before netif_receive_skb()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

set netlink_dump_control.module to avoid panic.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Cc: Roland Dreier <roland@kernel.org>
Cc: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I get a panic when I use ss -a and rmmod inet_diag at the
same time.

It's because netlink_dump uses inet_diag_dump which belongs to module
inet_diag.

I search the codes and find many modules have the same problem.  We
need to add a reference to the module which the cb->dump belongs to.

Thanks for all help from Stephen,Jan,Eric,Steffen and Pablo.

Change From v3:
change netlink_dump_start to inline,suggestion from Pablo and
Eric.

Change From v2:
delete netlink_dump_done,and call module_put in netlink_dump
and netlink_sock_destruct.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull UAPI disintegration fixes from David Howells:
 "There are three main parts:

 (1) I found I needed some more fixups in the wake of testing Arm64
     (some asm/unistd.h files had weird guards that caused problems -
     mostly in arches for which I don't have a compiler) and some
     __KERNEL__ splitting needed to take place in Arm64.

 (2) I found that c6x was missing some __KERNEL__ guards in its
     asm/signal.h.  Mark Salter pointed me at a tree with a patch to
     remove that file entirely and use the asm-generic variant instead.

 (3) Lastly, m68k turned out to have a header installation problem due
     to it lacking a kvm_para.h file.

     The conditional installation bits for linux/kvm_para.h, linux/kvm.h
     and linux/a.out.h weren't very well specified - and didn't work if
     an arch didn't have the asm/ version of that file, but there *was*
     an asm-generic/ version.

     It seems the "ifneq $((wildcard ...),)" for each of those three
     headers in include/kernel/Kbuild is invoked twice during header
     installation, and the second time it matches on the just installed
     asm-generic/kvm_para.h file and thus incorrectly installs
     linux/kvm_para.h as well.

     Most arches actually have an asm/kvm_para.h, so this wasn't
     detectable in those."

* 'uapi-prep' of git://git.infradead.org/users/dhowells/linux-headers:
  UAPI: Fix conditional header installation handling (notably kvm_para.h on m68k)
  c6x: remove c6x signal.h
  UAPI: Split compound conditionals containing __KERNEL__ in Arm64
  UAPI: Fix the guards on various asm/unistd.h files
  c6x: make dsk6455 the default config