Use the nvmem kernel api to expose the black box
chip functionality to userspace.

Using this feature, the device is capable of recording
to nonvolatile flash memory the vital data about the
system status that caused the system to perform a
black box write.

A blackbox is 64 bytes of data containing all the
status registers, last two states of the sequencer,
timestamp and counters. The mapping of this data is
described in the adm1266 datasheet.

On power-up the driver sets the unix time to
the adm1266 using the SET_RTC command. This value
is incremented by an internal clock and it is used
as timestamp for the black box feature.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20200812142055.9213-6-alexandru.tachici@analog.comSigned-off-by: Guenter Roeck <linux@roeck-us.net>

Add a debugfs entry which prints the current state
of the adm1266 sequencer.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20200812142055.9213-5-alexandru.tachici@analog.comSigned-off-by: Guenter Roeck <linux@roeck-us.net>

Adm1266 exposes 9 GPIOs and 16 PDIOs which are currently read-only. They
are controlled by the internal sequencing engine.

This patch makes adm1266 driver expose GPIOs and PDIOs to user-space
using GPIO provider kernel api.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20200812142055.9213-4-alexandru.tachici@analog.comSigned-off-by: Guenter Roeck <linux@roeck-us.net>

PmBus devices support Block Write-Block Read Process
Call described in SMBus specification v 2.0 with the
exception that Block writes and reads are permitted to
have up 255 data bytes instead of max 32 bytes (SMBus).

This patch adds Block WR process call support for ADM1266.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20200812142055.9213-3-alexandru.tachici@analog.comSigned-off-by: Guenter Roeck <linux@roeck-us.net>

Add pmbus probing driver for the adm1266 Cascadable
Super Sequencer with Margin Control and Fault Recording.
Driver is using the pmbus_core, creating sysfs files
under hwmon for inputs: vh1->vh4 and vp1->vp13.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20200812142055.9213-2-alexandru.tachici@analog.com
[groeck: Use .probe_new function, adjust for changed pmbus_do_probe API]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Add documentation for the newly added DTS support in the shtc1 driver.
To align with the drivers logic to have high precision by default
a boolean sensirion,low-precision is used to switch to low precision.
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200815012227.32538-3-chris.ruehl@gtsys.com.hkSigned-off-by: Guenter Roeck <linux@roeck-us.net>

Add support for DTS bindings for the sensirion shtc1,shtw1 and shtc3.
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200815012227.32538-2-chris.ruehl@gtsys.com.hk
[groeck: Resolved conflicts]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

dev_err_probe() can reduce code size, uniform error handling and record the
defer probe reason etc., use it to simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Link: https://lore.kernel.org/r/1597649673-22329-1-git-send-email-Anson.Huang@nxp.comSigned-off-by: Guenter Roeck <linux@roeck-us.net>

As part of the ongoing i2c transition to the simple probe
("probe_new"), this patch uses i2c_match_id to retrieve the
driver_data for the probed device. The id parameter is thus no longer
necessary and the simple probe can be used instead.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200821160035.590142-1-steve@sk2.orgSigned-off-by: Guenter Roeck <linux@roeck-us.net>

As part of the ongoing i2c transition to the simple probe
("probe_new"), this patch uses i2c_match_id to retrieve the
driver_data for the probed device. The id parameter is thus no longer
necessary and the simple probe can be used instead.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200821160159.591293-1-steve@sk2.orgSigned-off-by: Guenter Roeck <linux@roeck-us.net>

As part of the ongoing i2c transition to the simple probe
("probe_new"), this patch uses i2c_match_id to retrieve the
driver_data for the probed device. The id parameter is thus no longer
necessary and the simple probe can be used instead.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200821160231.592571-1-steve@sk2.orgSigned-off-by: Guenter Roeck <linux@roeck-us.net>

Many hwmon drivers don't use the id information provided by the old
i2c probe function, and the remainder can easily be adapted to the new
form ("probe_new") by calling i2c_match_id explicitly.

This avoids scanning the identifier tables during probes.

Drivers which didn't use the id are converted as-is; drivers which did
are modified to call i2c_match_id() with the same level of
error-handling (if any) as before.

This patch wraps up the transition for hwmon, with four stragglers not
included in the previous large patch.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200821160354.594715-1-steve@sk2.orgSigned-off-by: Guenter Roeck <linux@roeck-us.net>

This driver doesn't use the id information provided by the old i2c
probe function, so it can trivially be converted to the simple
("probe_new") form.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813162851.1519546-1-steve@sk2.orgSigned-off-by: Guenter Roeck <linux@roeck-us.net>

This driver doesn't use the id information provided by the old i2c
probe function, so it can trivially be converted to the simple
("probe_new") form.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813162704.1517951-1-steve@sk2.orgSigned-off-by: Guenter Roeck <linux@roeck-us.net>

This driver doesn't use the id information provided by the old i2c
probe function, so it can trivially be converted to the simple
("probe_new") form.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813162544.1516647-1-steve@sk2.orgSigned-off-by: Guenter Roeck <linux@roeck-us.net>

This driver doesn't use the id information provided by the old i2c
probe function, so it can trivially be converted to the simple
("probe_new") form.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813162300.1514695-1-steve@sk2.orgSigned-off-by: Guenter Roeck <linux@roeck-us.net>

This driver doesn't use the id information provided by the old i2c
probe function, so it can trivially be converted to the simple
("probe_new") form.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813162026.1512242-1-steve@sk2.orgSigned-off-by: Guenter Roeck <linux@roeck-us.net>

This driver doesn't use the id information provided by the old i2c
probe function, so it can trivially be converted to the simple
("probe_new") form.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813161845.1511261-1-steve@sk2.orgSigned-off-by: Guenter Roeck <linux@roeck-us.net>

This driver doesn't use the id information provided by the old i2c
probe function, so it can trivially be converted to the simple
("probe_new") form.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Acked-by: Corentin LABBE <clabbe.montjoie@gmail.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Link: https://lore.kernel.org/r/20200813161129.1507599-1-steve@sk2.orgSigned-off-by: Guenter Roeck <linux@roeck-us.net>

This driver doesn't use the id information provided by the old i2c
probe function, so it can trivially be converted to the simple
("probe_new") form.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813160958.1506536-1-steve@sk2.orgSigned-off-by: Guenter Roeck <linux@roeck-us.net>

Many hwmon drivers don't use the id information provided by the old
i2c probe function, and the remainder can easily be adapted to the new
form ("probe_new") by calling i2c_match_id explicitly.

This avoids scanning the identifier tables during probes.

Drivers which didn't use the id are converted as-is; drivers which did
are modified as follows:

* if the information in i2c_client is sufficient, that's used instead
  (client->name);
* anything else is handled by calling i2c_match_id() with the same
  level of error-handling (if any) as before.

A few drivers aren't included in this patch because they have a
different set of maintainers. They will be covered by other patches.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813160222.1503401-1-steve@sk2.orgSigned-off-by: Guenter Roeck <linux@roeck-us.net>

pmbus_do_probe doesn't use the id information provided in its second
argument, so this can be removed, which then allows using the
single-parameter i2c probe function ("probe_new") for probes.

This avoids scanning the identifier tables during probes.

Drivers which didn't use the id are converted as-is; drivers which did
are modified as follows:

* if the information in i2c_client is sufficient, that's used instead
  (client->name);
* configured v. probed comparisons are performed by comparing the
  configured name to the detected name, instead of the ids; this
  involves strcmp but is still cheaper than comparing all the device
  names when scanning the tables;
* anything else is handled by calling i2c_match_id() with the same
  level of error-handling (if any) as before.

Additionally, the mismatch message in the ltc2978 driver is adjusted
so that it no longer assumes that the driver_data is an index into
ltc2978_id.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Acked-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/20200808210004.30880-1-steve@sk2.orgSigned-off-by: Guenter Roeck <linux@roeck-us.net>

On some drives, reading the drive temperature resets the drive's
spin-down timer. If the drive temperature is read too often, affected
drives will never spin down. Add this information as usage note to
the driver documentation.
Reported-by: Peter Sulyok <peter@sulyok.net>
Cc: Peter Sulyok <peter@sulyok.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Adding implementation for new attributes (rated_min/rated_max) to
cover PMBus specification about rated values reporting:
MFR_VIN_MIN, MFR_VIN_MAX, MFR_IIN_MAX, MFR_PIN_MAX, MFR_VOUT_MIN,
MFR_VOUT_MAX, MFR_IOUT_MAX, MFR_POUT_MAX, MFR_MAX_TEMP_1/2/3.

Tested with OpenBMC stack. All rated attributes were available
and reported correct values.
Signed-off-by: Zbigniew Lukwinski <zbigniew.lukwinski@linux.intel.com>
Link: https://lore.kernel.org/r/1596224237-32280-4-git-send-email-zbigniew.lukwinski@linux.intel.comSigned-off-by: Guenter Roeck <linux@roeck-us.net>

Adding implementation for new attributes (rated_min/rated_max) for
currentX, inX, powerX, tempX and humidityX.

Tested with OpenBMC stack and simple hwmon driver using
rated_min/rated_max for the following types of sensors: hwmon_temp,
hwmon_in, hwmon_curr, hwmon_power, hwmon_humidity.
For each sensor rated attributes were available and returned
expected values.
Signed-off-by: Zbigniew Lukwinski <zbigniew.lukwinski@linux.intel.com>
Link: https://lore.kernel.org/r/1596224237-32280-3-git-send-email-zbigniew.lukwinski@linux.intel.comSigned-off-by: Guenter Roeck <linux@roeck-us.net>

New attributes (rated_min/rated_max) are being added the hwmon ABI.
They are needed to cover rated values documented by PMBus
specification:
PMBus Power System Mgt Protocol Specification - Part II – Revision 1.3.1,
chapters: 22.3.1 - 22.3.10, 22.3.15
Signed-off-by: Zbigniew Lukwinski <zbigniew.lukwinski@linux.intel.com>
Link: https://lore.kernel.org/r/1596224237-32280-2-git-send-email-zbigniew.lukwinski@linux.intel.comSigned-off-by: Guenter Roeck <linux@roeck-us.net>

Smatch has a new check for resource leaks which found a bug in probe:

    drivers/hwmon/w83627ehf.c:2417 w83627ehf_probe()
    warn: 'res->start' not released on lines: 2412.

We need to clean up if devm_hwmon_device_register_with_info() fails.

Fixes: 266cd583 ("hwmon: (w83627ehf) convert to with_info interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20200921125212.GA1128194@mwandaSigned-off-by: Guenter Roeck <linux@roeck-us.net>

Starting with MAX34451, the chips of this series support STATUS_IOUT and
STATUS_TEMPERATURE commands, and no longer report over-current and
over-temperature status with STATUS_MFR_SPECIFIC.

Fixes: 7a001dba ("hwmon: (pmbus/max34440) Add support for MAX34451.")
Fixes: 50115ac9 ("hwmon: (pmbus/max34440) Add support for MAX34460 and MAX34461")
Reported-by: Steve Foreman <foremans@google.com>
Cc: Steve Foreman <foremans@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

If the temperature is read before the internal calibration is
completed, the driver returns -EIO. Instead it should return -EAGAIN
to encourage repeating the operation.

Note (groeck): Returning -EAGAIN to userspace may result in hard loops;
some userspace code interprets -EAGAIN as request to retry immediately.
I would prefer -ENODATA, but it turns out that the thermal subsystem only
handles -EAGAIN silently, so we'll have to stick with that.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Link: https://lore.kernel.org/r/20200903134704.8949-1-lars.povlsen@microchip.comSigned-off-by: Guenter Roeck <linux@roeck-us.net>

Pull syscall tracing fix from Borislav Petkov:
 "Fix the seccomp syscall rewriting so that trace and audit see the
  rewritten syscall number, from Kees Cook"

* tag 'core_urgent_for_v5.9_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  core/entry: Report syscall correctly for trace and audit

Pull objtool fix from Borislav Petkov:
 "Fix noreturn detection for ignored sibling functions (Josh Poimboeuf)"

* tag 'objtool_urgent_for_v5.9_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  objtool: Fix noreturn detection for ignored functions

Pull locking fixes from Borislav Petkov:
 "Two fixes from the locking/urgent pile:

   - Fix lockdep's detection of "USED" <- "IN-NMI" inversions (Peter
     Zijlstra)

   - Make percpu-rwsem operations on the semaphore's ->read_count
     IRQ-safe because it can be used in an IRQ context (Hou Tao)"

* tag 'locking_urgent_for_v5.9_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/percpu-rwsem: Use this_cpu_{inc,dec}() for read_count
  locking/lockdep: Fix "USED" <- "IN-NMI" inversions

Pull EFI fix from Borislav Petkov:
 "Ensure that the EFI bootloader control module only probes successfully
  on systems that support the EFI SetVariable runtime service"

[ Tag and commit from Ard Biesheuvel, forwarded by Borislav ]

* tag 'efi-urgent-for-v5.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  efi: efibc: check for efivars write capability

Pull x86 fixes from Borislav Petkov:

 - A defconfig fix (Daniel Díaz)

 - Disable relocation relaxation for the compressed kernel when not
   built as -pie as in that case kernels built with clang and linked
   with LLD fail to boot due to the linker optimizing some instructions
   in non-PIE form; the gory details in the commit message (Arvind
   Sankar)

 - A fix for the "bad bp value" warning issued by the frame-pointer
   unwinder (Josh Poimboeuf)

* tag 'x86_urgent_for_v5.9_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/unwind/fp: Fix FP unwinding in ret_from_fork
  x86/boot/compressed: Disable relocation relaxation
  x86/defconfigs: Explicitly unset CONFIG_64BIT in i386_defconfig

Pull libnvdimm fixes from Dan Williams:
 "A handful of fixes to address a string of mistakes in the mechanism
  for device-mapper to determine if its component devices are dax
  capable.

   - Fix an original bug in device-mapper table reference counting when
     interrogating dax capability in the component device. This bug was
     hidden by the following bug.

   - Fix device-mapper to use the proper helper (dax_supported() instead
     of the leaf helper generic_fsdax_supported()) to determine dax
     operation of a stacked block device configuration. The original
     implementation is only valid for one level of dax-capable block
     device stacking. This bug was discovered while fixing the below
     regression.

   - Fix an infinite recursion regression introduced by broken attempts
     to quiet the generic_fsdax_supported() path and make it bail out
     before logging "dax capability not found" errors"

* tag 'libnvdimm-fixes-5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  dax: Fix stack overflow when mounting fsdax pmem device
  dm: Call proper helper to determine dax support
  dm/dax: Fix table reference counts

Pull RISC-V fixes from Palmer Dabbelt:

 - A fix for a lockdep issue to avoid an asserting triggering during
   early boot. There shouldn't be any incorrect behavior as the system
   isn't concurrent at the time.

 - The addition of a missing fence when installing early fixmap
   mappings.

 - A corretion to the K210 device tree's interrupt map.

 - A fix for M-mode timer handling on the K210.

* tag 'riscv-for-linus-5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  RISC-V: Resurrect the MMIO timer implementation for M-mode systems
  riscv: Fix Kendryte K210 device tree
  riscv: Add sfence.vma after early page table changes
  RISC-V: Take text_mutex in ftrace_init_nop()

Pull USB/Thunderbolt fixes from Greg KH:
 "Here are some small USB and one Thunderbolt driver fixes.

  Nothing major at all, just some fixes for reported issues, and a quirk
  addition:

   - typec fixes

   - UAS disconnect fix

   - usblp race fix

   - ehci-hcd modversions build fix

   - ignore wakeup quirk table addition

   - thunderbolt DROM read fix

  All of these have been in linux-next with no reported issues"

* tag 'usb-5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usblp: fix race between disconnect() and read()
  ehci-hcd: Move include to keep CRC stable
  usb: typec: intel_pmc_mux: Handle SCU IPC error conditions
  USB: quirks: Add USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk for BYD zhaoxin notebook
  USB: UAS: fix disconnect by unplugging a hub
  usb: typec: ucsi: Prevent mode overrun
  usb: typec: ucsi: acpi: Increase command completion timeout value
  thunderbolt: Retry DROM read once if parsing fails

Pull tty/serial/fbcon fixes from Greg KH:
 "Here are some small tty/serial and one more fbcon fix.

  They include:

   - serial core locking regression fixes

   - new device ids for 8250_pci driver

   - fbcon fix for syzbot found issue

  All have been in linux-next with no reported issues"

* tag 'tty-5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  fbcon: Fix user font detection test at fbcon_resize().
  serial: 8250_pci: Add Realtek 816a and 816b
  serial: core: fix console port-lock regression
  serial: core: fix port-lock initialisation

Pull EDAC fixes from Borislav Petkov:
 "Two fixes for resulting from CONFIG_DEBUG_TEST_DRIVER_REMOVE=y
  experiments:

   - complete a previous fix to reset a local structure containing
     scanned system data properly so that the driver rescans, as it
     should, on a second load.

   - address a refcount underflow due to not paying attention to the
     driver whitelest on unregister"

* tag 'edac_urgent_for_v5.9_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
  EDAC/ghes: Check whether the driver is on the safe list correctly
  EDAC/ghes: Clear scanned data on unload