- 28 Sep, 2017 10 commits
-
-
Ed Blake authored
Re-enable the MAC receiver by setting CONFIG_RE before powering down, as instructed in section 6.3.5.1 of [1]. Without this the MAC fails to receive WoL packets and never wakes up. [1] DWC Ethernet QoS Databook 4.10a October 2014 Signed-off-by:
Ed Blake <ed.blake@sondrel.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ed Blake authored
Add hook to stmmac_pltfr_pm_ops for suspend / resume handling. Signed-off-by:
Ed Blake <ed.blake@sondrel.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
We cannot be registering the network device first, then setting its carrier off and finally connecting it to a PHY, doing that leaves a window during which the carrier is at best inconsistent, and at worse the device is not usable without a down/up sequence since the network device is visible to user space with possibly no PHY device attached. Re-order steps so that they make logical sense. This fixes some devices where the port was not usable after e.g: an unbind then bind of the driver. Fixes: 0071f56e ("dsa: Register netdev before phy") Fixes: 91da11f8 ("net: Distributed Switch Architecture protocol support") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Andrew Lunn authored
Ports with the same VLAN must all be in the same bridge. However the CPU and DSA ports need to be in multiple VLANs spread over multiple bridges. So exclude them when performing this test. Fixes: b2f81d30 ("net: dsa: add CPU and DSA ports as VLAN members") Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Reviewed-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
My prior fix was not complete, as we were dereferencing a pointer three times per node, not twice as I initially thought. Fixes: 4cc5b44b ("inetpeer: fix RCU lookup()") Fixes: b145425f ("inetpeer: remove AVL implementation in favor of RB tree") Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Antoine Tenart says: ==================== net: mvpp2: various fixes This series contains 3 fixes for the Marvell PPv2 driver. Since v1: - Removed one patch about dma masks as it would need a better fix. - Added one fix about the MAC Tx clock source selection. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Antoine Tenart authored
This patch stops the internal MAC Tx clock from being enabled as the internal clock isn't used. The definition used for the bit controlling this behaviour is renamed as well as it was wrongly named (bit 4 of GMAC_CTRL_2_REG). Fixes: 3919357f ("net: mvpp2: initialize the GMAC when using a port") Signed-off-by:
Antoine Tenart <antoine.tenart@free-electrons.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Yan Markman authored
The private port_list array has a list of pointers to mvpp2_port instances. This list is allocated given the number of ports enabled in the device tree, but the pointers are set using the port-id property. If on a single port is enabled, the port_list array will be of size 1, but when registering the port, if its id is not 0 the driver will crash. Other crashes were encountered in various situations. This fixes the issue by using an index not equal to the value of the port-id property. Fixes: 3f518509 ("ethernet: Add new driver for Marvell Armada 375 network unit") Signed-off-by:
Antoine Tenart <antoine.tenart@free-electrons.com> Signed-off-by:
Yan Markman <ymarkman@marvell.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Stefan Chulski authored
Parsing fragmentation detection failed due to wrong configured parser TCAM entry's. Some traffic was marked as fragmented in RX descriptor, even it wasn't IP fragmented. The hardware also failed to calculate checksums which lead to use software checksum and caused performance degradation. Fixes: 3f518509 ("ethernet: Add new driver for Marvell Armada 375 network unit") Signed-off-by:
Antoine Tenart <antoine.tenart@free-electrons.com> Signed-off-by:
Stefan Chulski <stefanc@marvell.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Alexander Potapenko authored
KMSAN (https://github.com/google/kmsan) reported accessing uninitialized skb->data[0] in the case the skb is empty (i.e. skb->len is 0): ================================================ BUG: KMSAN: use of uninitialized memory in tun_get_user+0x19ba/0x3770 CPU: 0 PID: 3051 Comm: probe Not tainted 4.13.0+ #3140 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Call Trace: ... __msan_warning_32+0x66/0xb0 mm/kmsan/kmsan_instr.c:477 tun_get_user+0x19ba/0x3770 drivers/net/tun.c:1301 tun_chr_write_iter+0x19f/0x300 drivers/net/tun.c:1365 call_write_iter ./include/linux/fs.h:1743 new_sync_write fs/read_write.c:457 __vfs_write+0x6c3/0x7f0 fs/read_write.c:470 vfs_write+0x3e4/0x770 fs/read_write.c:518 SYSC_write+0x12f/0x2b0 fs/read_write.c:565 SyS_write+0x55/0x80 fs/read_write.c:557 do_syscall_64+0x242/0x330 arch/x86/entry/common.c:284 entry_SYSCALL64_slow_path+0x25/0x25 arch/x86/entry/entry_64.S:245 ... origin: ... kmsan_poison_shadow+0x6e/0xc0 mm/kmsan/kmsan.c:211 slab_alloc_node mm/slub.c:2732 __kmalloc_node_track_caller+0x351/0x370 mm/slub.c:4351 __kmalloc_reserve net/core/skbuff.c:138 __alloc_skb+0x26a/0x810 net/core/skbuff.c:231 alloc_skb ./include/linux/skbuff.h:903 alloc_skb_with_frags+0x1d7/0xc80 net/core/skbuff.c:4756 sock_alloc_send_pskb+0xabf/0xfe0 net/core/sock.c:2037 tun_alloc_skb drivers/net/tun.c:1144 tun_get_user+0x9a8/0x3770 drivers/net/tun.c:1274 tun_chr_write_iter+0x19f/0x300 drivers/net/tun.c:1365 call_write_iter ./include/linux/fs.h:1743 new_sync_write fs/read_write.c:457 __vfs_write+0x6c3/0x7f0 fs/read_write.c:470 vfs_write+0x3e4/0x770 fs/read_write.c:518 SYSC_write+0x12f/0x2b0 fs/read_write.c:565 SyS_write+0x55/0x80 fs/read_write.c:557 do_syscall_64+0x242/0x330 arch/x86/entry/common.c:284 return_from_SYSCALL_64+0x0/0x6a arch/x86/entry/entry_64.S:245 ================================================ Make sure tun_get_user() doesn't touch skb->data[0] unless there is actual data. C reproducer below: ========================== // autogenerated by syzkaller (http://github.com/google/syzkaller) #define _GNU_SOURCE #include <fcntl.h> #include <linux/if_tun.h> #include <netinet/ip.h> #include <net/if.h> #include <string.h> #include <sys/ioctl.h> int main() { int sock = socket(PF_INET, SOCK_STREAM, IPPROTO_IP); int tun_fd = open("/dev/net/tun", O_RDWR); struct ifreq req; memset(&req, 0, sizeof(struct ifreq)); strcpy((char*)&req.ifr_name, "gre0"); req.ifr_flags = IFF_UP | IFF_MULTICAST; ioctl(tun_fd, TUNSETIFF, &req); ioctl(sock, SIOCSIFFLAGS, "gre0"); write(tun_fd, "hi", 0); return 0; } ========================== Signed-off-by:
Alexander Potapenko <glider@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- 27 Sep, 2017 2 commits
-
-
Dan Carpenter authored
The sctp_for_each_transport() function takes an pointer to int. The cb->args[] array holds longs so it's only using the high 32 bits. It works on little endian system but will break on big endian 64 bit machines. Fixes: d25adbeb ("sctp: fix an use-after-free issue in sctp_sock_dump") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
Neil Horman <nhorman@tuxdriver.com> Reviewed-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Merge tag 'wireless-drivers-for-davem-2017-09-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers Kalle Valo says: ==================== wireless-drivers fixes for 4.14 Quite a lot of fixes this time. Most notable is the brcmfmac fix for a CVE issue. iwlwifi * a couple of bugzilla bugs related to multicast handling * two fixes for WoWLAN bugs that were causing queue hangs and re-initialization problems * two fixes for potential uninitialized variable use reported by Dan Carpenter in relation to a recently introduced patch * a fix for buffer reordering in the newly supported 9000 device family * fix a race when starting aggregation * small fix for a recent patch to wake mac80211 queues * send non-bufferable management frames in the generic queue so they are not sent on queues that are under power-save ath10k * fix a PCI PM related gcc warning brcmfmac * CVE-2017-0786: add length check scan results from firmware * respect passive scan requests from user space qtnfmac * fix race in tx path when using multiple interfaces * cancel ongoing scan when removing the wireless interface ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- 26 Sep, 2017 9 commits
-
-
David S. Miller authored
Igor Russkikh says: ==================== aquantia: Atlantic driver bugfixes und improvements This series contains bugfixes for aQuantia Atlantic driver. Changes in v2: Review comments applied: - min_mtu set removed - extra mtu range check is removed - err codes handling improved ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Pavel Belous authored
Call skb_frag_dma_map multiple times if tx length is greater than device max and avoid processing tx ring until entire packet has been sent. Signed-off-by:
Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by:
Pavel Belous <pavel.belous@aquantia.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Igor Russkikh authored
Due to a bug in aquantia atlantic card firmware, it sometimes reports invalid link speed bits. That caused driver to report link down events, although link itself is totally fine. This patch ignores such out of blue readings. Signed-off-by:
Pavel Belous <Pavel.Belous@aquantia.com> Signed-off-by:
Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Igor Russkikh authored
Driver did a poor job in managing its Tx queues: Sometimes it could stop tx queues due to link down condition in aq_nic_xmit - but never waked up them. That led to Tx path total suspend. This patch fixes this and improves generic queue management: - introduces queue restart counter - uses generic netif_ interface to disable and enable tx path - refactors link up/down condition and introduces dmesg log event when link changes. - introduces new constant for minimum descriptors count required for queue wakeup Signed-off-by:
Pavel Belous <Pavel.Belous@aquantia.com> Signed-off-by:
Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Igor Russkikh authored
Although hardware is capable for almost 16K MTU, without max_mtu field correctly set it only allows standard MTU to be used. This patch enables max MTU, calculating it from hardware maximum frame size of 16352 octets (including FCS). Fixes: 5513e164 ("net: ethernet: aquantia: Fixes for aq_ndev_change_mtu") Signed-off-by:
Pavel Belous <Pavel.Belous@aquantia.com> Signed-off-by:
Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Sabrina Dubroca authored
If we try to delete the same tunnel twice, the first delete operation does a lookup (l2tp_tunnel_get), finds the tunnel, calls l2tp_tunnel_delete, which queues it for deletion by l2tp_tunnel_del_work. The second delete operation also finds the tunnel and calls l2tp_tunnel_delete. If the workqueue has already fired and started running l2tp_tunnel_del_work, then l2tp_tunnel_delete will queue the same tunnel a second time, and try to free the socket again. Add a dead flag to prevent firing the workqueue twice. Then we can remove the check of queue_work's result that was meant to prevent that race but doesn't. Reproducer: ip l2tp add tunnel tunnel_id 3000 peer_tunnel_id 4000 local 192.168.0.2 remote 192.168.0.1 encap udp udp_sport 5000 udp_dport 6000 ip l2tp add session name l2tp1 tunnel_id 3000 session_id 1000 peer_session_id 2000 ip link set l2tp1 up ip l2tp del tunnel tunnel_id 3000 ip l2tp del tunnel tunnel_id 3000 Fixes: f8ccac0e ("l2tp: put tunnel socket release on a workqueue") Reported-by:
Jianlin Shi <jishi@redhat.com> Signed-off-by:
Sabrina Dubroca <sd@queasysnail.net> Acked-by:
Guillaume Nault <g.nault@alphalink.fr> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Alexey Kodanev authored
When running LTP IPsec tests, KASan might report: BUG: KASAN: use-after-free in vti_tunnel_xmit+0xeee/0xff0 [ip_vti] Read of size 4 at addr ffff880dc6ad1980 by task swapper/0/0 ... Call Trace: <IRQ> dump_stack+0x63/0x89 print_address_description+0x7c/0x290 kasan_report+0x28d/0x370 ? vti_tunnel_xmit+0xeee/0xff0 [ip_vti] __asan_report_load4_noabort+0x19/0x20 vti_tunnel_xmit+0xeee/0xff0 [ip_vti] ? vti_init_net+0x190/0x190 [ip_vti] ? save_stack_trace+0x1b/0x20 ? save_stack+0x46/0xd0 dev_hard_start_xmit+0x147/0x510 ? icmp_echo.part.24+0x1f0/0x210 __dev_queue_xmit+0x1394/0x1c60 ... Freed by task 0: save_stack_trace+0x1b/0x20 save_stack+0x46/0xd0 kasan_slab_free+0x70/0xc0 kmem_cache_free+0x81/0x1e0 kfree_skbmem+0xb1/0xe0 kfree_skb+0x75/0x170 kfree_skb_list+0x3e/0x60 __dev_queue_xmit+0x1298/0x1c60 dev_queue_xmit+0x10/0x20 neigh_resolve_output+0x3a8/0x740 ip_finish_output2+0x5c0/0xe70 ip_finish_output+0x4ba/0x680 ip_output+0x1c1/0x3a0 xfrm_output_resume+0xc65/0x13d0 xfrm_output+0x1e4/0x380 xfrm4_output_finish+0x5c/0x70 Can be fixed if we get skb->len before dst_output(). Fixes: b9959fd3 ("vti: switch to new ip tunnel code") Fixes: 22e1b23d ("vti6: Support inter address family tunneling.") Signed-off-by:
Alexey Kodanev <alexey.kodanev@oracle.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Arnd Bergmann authored
When CONFIG_KASAN is enabled, the "--param asan-stack=1" causes rather large stack frames in some functions. This goes unnoticed normally because CONFIG_FRAME_WARN is disabled with CONFIG_KASAN by default as of commit 3f181b4d ("lib/Kconfig.debug: disable -Wframe-larger-than warnings with KASAN=y"). The kernelci.org build bot however has the warning enabled and that led me to investigate it a little further, as every build produces these warnings: net/wireless/nl80211.c:4389:1: warning: the frame size of 2240 bytes is larger than 2048 bytes [-Wframe-larger-than=] net/wireless/nl80211.c:1895:1: warning: the frame size of 3776 bytes is larger than 2048 bytes [-Wframe-larger-than=] net/wireless/nl80211.c:1410:1: warning: the frame size of 2208 bytes is larger than 2048 bytes [-Wframe-larger-than=] net/bridge/br_netlink.c:1282:1: warning: the frame size of 2544 bytes is larger than 2048 bytes [-Wframe-larger-than=] Most of this problem is now solved in gcc-8, which can consolidate the stack slots for the inline function arguments. On older compilers we can add a workaround by declaring a local variable in each function to pass the inline function argument. Cc: stable@vger.kernel.org Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81715Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Arnd Bergmann authored
Inlining these functions creates lots of stack variables that each take 64 bytes when KASAN is enabled, leading to this warning about potential stack overflow: drivers/net/ethernet/rocker/rocker_ofdpa.c: In function 'ofdpa_cmd_flow_tbl_add': drivers/net/ethernet/rocker/rocker_ofdpa.c:621:1: error: the frame size of 2752 bytes is larger than 1536 bytes [-Werror=frame-larger-than=] gcc-8 can now consolidate the stack slots itself, but on older versions we get the same behavior by using a temporary variable that holds a copy of the inline function argument. Cc: stable@vger.kernel.org Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81715Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- 25 Sep, 2017 5 commits
-
-
Timur Tabi authored
When mapping the RX DMA buffers, the driver was accidentally specifying zero for the buffer length. Under normal circumstances, SWIOTLB does not need to allocate a bounce buffer, so the address is just mapped without checking the size field. This is why the error was not detected earlier. Fixes: b9b17deb ("net: emac: emac gigabit ethernet controller driver") Cc: stable@vger.kernel.org Signed-off-by:
Timur Tabi <timur@codeaurora.org> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Guillaume Nault says: ==================== l2tp: fix some races in session deletion L2TP provides several interfaces for deleting sessions. Using two of them concurrently can lead to use-after-free bugs. Patch #2 uses a flag to prevent double removal of L2TP sessions. Patch #1 fixes a bug found in the way. Fixing this bug is also necessary for patch #2 to handle all cases. This issue is similar to the tunnel deletion bug being worked on by Sabrina: https://patchwork.ozlabs.org/patch/814173/ ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Guillaume Nault authored
There are several ways to remove L2TP sessions: * deleting a session explicitly using the netlink interface (with L2TP_CMD_SESSION_DELETE), * deleting the session's parent tunnel (either by closing the tunnel's file descriptor or using the netlink interface), * closing the PPPOL2TP file descriptor of a PPP pseudo-wire. In some cases, when these methods are used concurrently on the same session, the session can be removed twice, leading to use-after-free bugs. This patch adds a 'dead' flag, used by l2tp_session_delete() and l2tp_tunnel_closeall() to prevent them from stepping on each other's toes. The session deletion path used when closing a PPPOL2TP file descriptor doesn't need to be adapted. It already has to ensure that a session remains valid for the lifetime of its PPPOL2TP file descriptor. So it takes an extra reference on the session in the ->session_close() callback (pppol2tp_session_close()), which is eventually dropped in the ->sk_destruct() callback of the PPPOL2TP socket (pppol2tp_session_destruct()). Still, __l2tp_session_unhash() and l2tp_session_queue_purge() can be called twice and even concurrently for a given session, but thanks to proper locking and re-initialisation of list fields, this is not an issue. Signed-off-by:
Guillaume Nault <g.nault@alphalink.fr> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Guillaume Nault authored
If l2tp_tunnel_delete() or l2tp_tunnel_closeall() deletes a session right after pppol2tp_release() orphaned its socket, then the 'sock' variable of the pppol2tp_session_close() callback is NULL. Yet the session is still used by pppol2tp_release(). Therefore we need to take an extra reference in any case, to prevent l2tp_tunnel_delete() or l2tp_tunnel_closeall() from freeing the session. Since the pppol2tp_session_close() callback is only set if the session is associated to a PPPOL2TP socket and that both l2tp_tunnel_delete() and l2tp_tunnel_closeall() hold the PPPOL2TP socket before calling pppol2tp_session_close(), we're sure that pppol2tp_session_close() and pppol2tp_session_destruct() are paired and called in the right order. So the reference taken by the former will be released by the later. Signed-off-by:
Guillaume Nault <g.nault@alphalink.fr> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Kalle Valo authored
ath.git fixes for 4.14. Major changes: ath10k * fix a PCI PM related gcc warning
-
- 24 Sep, 2017 2 commits
-
-
Subash Abhinov Kasiviswanathan authored
Xiaolong reported a suspicious rcu_dereference_check in the device unregister notifier callback. Since we do not dereference the rx_handler_data, it's ok to just check for the value of the pointer. Note that this section is already protected by rtnl_lock. [ 101.364846] WARNING: suspicious RCU usage [ 101.365654] 4.13.0-rc6-01701-gceed73a2 #1 Not tainted [ 101.370873] ----------------------------- [ 101.372472] drivers/net/ethernet/qualcomm/rmnet/rmnet_config.c:57 suspicious rcu_dereference_check() usage! [ 101.374427] [ 101.374427] other info that might help us debug this: [ 101.374427] [ 101.387491] [ 101.387491] rcu_scheduler_active = 2, debug_locks = 1 [ 101.389368] 1 lock held by trinity-main/2809: [ 101.390736] #0: (rtnl_mutex){+.+.+.}, at: [<8146085b>] rtnl_lock+0xf/0x11 [ 101.395482] [ 101.395482] stack backtrace: [ 101.396948] CPU: 0 PID: 2809 Comm: trinity-main Not tainted 4.13.0-rc6-01701-gceed73a2 #1 [ 101.398857] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.9.3-20161025_171302-gandalf 04/01/2014 [ 101.401079] Call Trace: [ 101.401656] dump_stack+0xa1/0xeb [ 101.402871] lockdep_rcu_suspicious+0xc7/0xd0 [ 101.403665] rmnet_is_real_dev_registered+0x40/0x4e [ 101.405199] rmnet_config_notify_cb+0x2c/0x142 [ 101.406344] ? wireless_nlevent_flush+0x47/0x71 [ 101.407385] notifier_call_chain+0x2d/0x47 [ 101.408645] raw_notifier_call_chain+0xc/0xe [ 101.409882] call_netdevice_notifiers_info+0x41/0x49 [ 101.411402] call_netdevice_notifiers+0xc/0xe [ 101.412713] rollback_registered_many+0x268/0x36e [ 101.413702] rollback_registered+0x39/0x56 [ 101.414965] unregister_netdevice_queue+0x79/0x88 [ 101.415908] unregister_netdev+0x16/0x1d Fixes: ceed73a2 ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation") Signed-off-by:
Subash Abhinov Kasiviswanathan <subashab@codeaurora.org> Reported-by:
kernel test robot <xiaolong.ye@intel.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Christophe JAILLET authored
All the error handling paths 'goto error', except this one. We should also go to error in this case, or some resources will be leaking. Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- 23 Sep, 2017 12 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linuxLinus Torvalds authored
Pull parisc fixes from Helge Deller: - Unbreak parisc bootloader by avoiding a gcc-7 optimization to convert multiple byte-accesses into one word-access. - Add missing HWPOISON page fault handler code. I completely missed that when I added HWPOISON support during this merge window and it only showed up now with the madvise07 LTP test case. - Fix backtrace unwinding to stop when stack start has been reached. - Issue warning if initrd has been loaded into memory regions with broken RAM modules. - Fix HPMC handler (parisc hardware fault handler) to comply with architecture specification. - Avoid compiler warnings about too large frame sizes. - Minor init-section fixes. * 'parisc-4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux: parisc: Unbreak bootloader due to gcc-7 optimizations parisc: Reintroduce option to gzip-compress the kernel parisc: Add HWPOISON page fault handler code parisc: Move init_per_cpu() into init section parisc: Check if initrd was loaded into broken RAM parisc: Add PDCE_CHECK instruction to HPMC handler parisc: Add wrapper for pdc_instr() firmware function parisc: Move start_parisc() into init section parisc: Stop unwinding at start of stack parisc: Fix too large frame size warnings
-
git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdmaLinus Torvalds authored
Pull rdma fixes from Doug Ledford: - Smattering of miscellanous fixes - A five patch series for i40iw that had a patch (5/5) that was larger than I would like, but I took it because it's needed for large scale users - An 8 patch series for bnxt_re that landed right as I was leaving on PTO and so had to wait until now...they are all appropriate fixes for -rc IMO * tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (22 commits) bnxt_re: Don't issue cmd to delete GID for QP1 GID entry before the QP is destroyed bnxt_re: Fix memory leak in FRMR path bnxt_re: Remove RTNL lock dependency in bnxt_re_query_port bnxt_re: Fix race between the netdev register and unregister events bnxt_re: Free up devices in module_exit path bnxt_re: Fix compare and swap atomic operands bnxt_re: Stop issuing further cmds to FW once a cmd times out bnxt_re: Fix update of qplib_qp.mtu when modified i40iw: Add support for port reuse on active side connections i40iw: Add missing VLAN priority i40iw: Call i40iw_cm_disconn on modify QP to disconnect i40iw: Prevent multiple netdev event notifier registrations i40iw: Fail open if there are no available MSI-X vectors RDMA/vmw_pvrdma: Fix reporting correct opcodes for completion IB/bnxt_re: Fix frame stack compilation warning IB/mlx5: fix debugfs cleanup IB/ocrdma: fix incorrect fall-through on switch statement IB/ipoib: Suppress the retry related completion errors iw_cxgb4: remove the stid on listen create failure iw_cxgb4: drop listen destroy replies if no ep found ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds authored
Pull networking fixes from David Miller: 1) Fix NAPI poll list corruption in enic driver, from Christian Lamparter. 2) Fix route use after free, from Eric Dumazet. 3) Fix regression in reuseaddr handling, from Josef Bacik. 4) Assert the size of control messages in compat handling since we copy it in from userspace twice. From Meng Xu. 5) SMC layer bug fixes (missing RCU locking, bad refcounting, etc.) from Ursula Braun. 6) Fix races in AF_PACKET fanout handling, from Willem de Bruijn. 7) Don't use ARRAY_SIZE on spinlock array which might have zero entries, from Geert Uytterhoeven. 8) Fix miscomputation of checksum in ipv6 udp code, from Subash Abhinov Kasiviswanathan. 9) Push the ipv6 header properly in ipv6 GRE tunnel driver, from Xin Long. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (75 commits) inet: fix improper empty comparison net: use inet6_rcv_saddr to compare sockets net: set tb->fast_sk_family net: orphan frags on stand-alone ptype in dev_queue_xmit_nit MAINTAINERS: update git tree locations for ieee802154 subsystem net: prevent dst uses after free net: phy: Fix truncation of large IRQ numbers in phy_attached_print() net/smc: no close wait in case of process shut down net/smc: introduce a delay net/smc: terminate link group if out-of-sync is received net/smc: longer delay for client link group removal net/smc: adapt send request completion notification net/smc: adjust net_device refcount net/smc: take RCU read lock for routing cache lookup net/smc: add receive timeout check net/smc: add missing dev_put net: stmmac: Cocci spatch "of_table" lan78xx: Use default values loaded from EEPROM/OTP after reset lan78xx: Allow EEPROM write for less than MAX_EEPROM_SIZE lan78xx: Fix for eeprom read/write when device auto suspend ...
-
Linus Torvalds authored
Merge tag 'apparmor-pr-2017-09-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor Pull apparmor updates from John Johansen: "This is the apparmor pull request, similar to SELinux and seccomp. It's the same series that I was sent to James' security tree + one regression fix that was found after the series was sent to James and would have been sent for v4.14-rc2. Features: - in preparation for secid mapping add support for absolute root view based labels - add base infastructure for socket mediation - add mount mediation - add signal mediation minor cleanups and changes: - be defensive, ensure unconfined profiles have dfas initialized - add more debug asserts to apparmorfs - enable policy unpacking to audit different reasons for failure - cleanup conditional check for label in label_print - Redundant condition: prev_ns. in [label.c:1498] Bug Fixes: - fix regression in apparmorfs DAC access permissions - fix build failure on sparc caused by undeclared signals - fix sparse report of incorrect type assignment when freeing label proxies - fix race condition in null profile creation - Fix an error code in aafs_create() - Fix logical error in verify_header() - Fix shadowed local variable in unpack_trans_table()" * tag 'apparmor-pr-2017-09-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor: apparmor: fix apparmorfs DAC access permissions apparmor: fix build failure on sparc caused by undeclared signals apparmor: fix incorrect type assignment when freeing proxies apparmor: ensure unconfined profiles have dfas initialized apparmor: fix race condition in null profile creation apparmor: move new_null_profile to after profile lookup fns() apparmor: add base infastructure for socket mediation apparmor: add more debug asserts to apparmorfs apparmor: make policy_unpack able to audit different info messages apparmor: add support for absolute root view based labels apparmor: cleanup conditional check for label in label_print apparmor: add mount mediation apparmor: add the ability to mediate signals apparmor: Redundant condition: prev_ns. in [label.c:1498] apparmor: Fix an error code in aafs_create() apparmor: Fix logical error in verify_header() apparmor: Fix shadowed local variable in unpack_trans_table()
-
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pmLinus Torvalds authored
Pull ACPI fixes from Rafael Wysocki: "These fix the initialization of resources in the ACPI WDAT watchdog driver, a recent regression in the ACPI device properties handling, a recent change in behavior causing the ACPI_HANDLE() macro to only work for GPL code and create a MAINTAINERS entry for ACPI PMIC drivers in order to specify the official reviewers for that code. Specifics: - Fix the initialization of resources in the ACPI WDAT watchdog driver that uses unititialized memory which causes compiler warnings to be triggered (Arnd Bergmann). - Fix a recent regression in the ACPI device properties handling that causes some device properties data to be skipped during enumeration (Sakari Ailus). - Fix a recent change in behavior that caused the ACPI_HANDLE() macro to stop working for non-GPL code which is a problem for the NVidia binary graphics driver, for example (John Hubbard). - Add a MAINTAINERS entry for the ACPI PMIC drivers to specify the official reviewers for that code (Rafael Wysocki)" * tag 'acpi-4.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: ACPI: properties: Return _DSD hierarchical extension (data) sub-nodes correctly ACPI / bus: Make ACPI_HANDLE() work for non-GPL code again ACPI / watchdog: properly initialize resources ACPI / PMIC: Add code reviewers to MAINTAINERS
-
David S. Miller authored
Josef Bacik says: ==================== net: fix reuseaddr regression I introduced a regression when reworking the fastreuse port stuff that allows bind conflicts to occur once a reuseaddr successfully opens on an existing tb. The root cause is I reversed an if statement which caused us to set the tb as if there were no owners on the socket if there were, which obviously is not correct. Dave could you please queue these changes up for -stable, I've run them through the net tests and added another test to check for this problem specifically. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Josef Bacik authored
When doing my reuseport rework I screwed up and changed a if (hlist_empty(&tb->owners)) to if (!hlist_empty(&tb->owners)) This is obviously bad as all of the reuseport/reuse logic was reversed, which caused weird problems like allowing an ipv4 bind conflict if we opened an ipv4 only socket on a port followed by an ipv6 only socket on the same port. Fixes: b9470c27 ("inet: kill smallest_size and smallest_port") Reported-by:
Cole Robinson <crobinso@redhat.com> Signed-off-by:
Josef Bacik <jbacik@fb.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Josef Bacik authored
In ipv6_rcv_saddr_equal() we need to use inet6_rcv_saddr(sk) for the ipv6 compare with the fast socket information to make sure we're doing the proper comparisons. Fixes: 637bc8bb ("inet: reset tb->fastreuseport when adding a reuseport sk") Reported-and-tested-by:
Cole Robinson <crobinso@redhat.com> Signed-off-by:
Josef Bacik <jbacik@fb.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Josef Bacik authored
We need to set the tb->fast_sk_family properly so we can use the proper comparison function for all subsequent reuseport bind requests. Fixes: 637bc8bb ("inet: reset tb->fastreuseport when adding a reuseport sk") Reported-and-tested-by:
Cole Robinson <crobinso@redhat.com> Signed-off-by:
Josef Bacik <jbacik@fb.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Willem de Bruijn authored
Zerocopy skbs frags are copied when the skb is looped to a local sock. Commit 1080e512 ("net: orphan frags on receive") introduced calls to skb_orphan_frags to deliver_skb and __netif_receive_skb for this. With msg_zerocopy, these skbs can also exist in the tx path and thus loop from dev_queue_xmit_nit. This already calls deliver_skb in its loop. But it does not orphan before a separate pt_prev->func(). Add the missing skb_orphan_frags_rx. Changes v1->v2: handle skb_orphan_frags_rx failure Fixes: 1f8b977a ("sock: enable MSG_ZEROCOPY") Signed-off-by:
Willem de Bruijn <willemb@google.com> Reviewed-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pmLinus Torvalds authored
Pull power management fixes from Rafael Wysocki: "These fix a cpufreq regression introduced by recent changes related to the generic DT driver, an initialization time memory leak in cpuidle on ARM, a PM core bug that may cause system suspend/resume to fail on some systems, a request type validation issue in the PM QoS framework and two documentation-related issues. Specifics: - Fix a regression in cpufreq on systems using DT as the source of CPU configuration information where two different code paths attempt to create the cpufreq-dt device object (there can be only one) and fix up the "compatible" matching for some TI platforms on top of that (Viresh Kumar, Dave Gerlach). - Fix an initialization time memory leak in cpuidle on ARM which occurs if the cpuidle driver initialization fails (Stefan Wahren). - Fix a PM core function that checks whether or not there are any system suspend/resume callbacks for a device, but forgets to check legacy callbacks which then may be skipped incorrectly and the system may crash and/or the device may become unusable after a suspend-resume cycle (Rafael Wysocki). - Fix request type validation for latency tolerance PM QoS requests which may lead to unexpected behavior (Jan Schönherr). - Fix a broken link to PM documentation from a header file and a typo in a PM document (Geert Uytterhoeven, Rafael Wysocki)" * tag 'pm-4.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: cpufreq: ti-cpufreq: Support additional am43xx platforms ARM: cpuidle: Avoid memleak if init fail cpufreq: dt-platdev: Add some missing platforms to the blacklist PM: core: Fix device_pm_check_callbacks() PM: docs: Drop an excess character from devices.rst PM / QoS: Use the correct variable to check the QoS request type driver core: Fix link to device power management documentation
-
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/inputLinus Torvalds authored
Pull input fixes from Dmitry Torokhov: - fixes for two long standing issues (lock up and a crash) in force feedback handling in uinput driver - tweak to firmware update timing in Elan I2C touchpad driver. * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: elan_i2c - extend Flash-Write delay Input: uinput - avoid crash when sending FF request to device going away Input: uinput - avoid FF flush when destroying device
-