The of_device_id tables used for matching should be terminated with
empty sentinel values.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Barry Song <baohua.song@csr.com>

commit d5341942 ("PCI: Make the struct
pci_dev * argument of pci_fixup_irqs const") did not change argument
of pdev_to_cnspci(), and thus introduced the following warnings:

  CHECK   arch/arm/mach-cns3xxx/pcie.c
pcie.c:177:60: warning: incorrect type in argument 1 (different modifiers)
pcie.c:177:60:    expected struct pci_dev *dev
pcie.c:177:60:    got struct pci_dev const *dev
  CC      arch/arm/mach-cns3xxx/pcie.o
pcie.c: In function 'cns3xxx_pcie_map_irq':
pcie.c:177: warning: passing argument 1 of 'pdev_to_cnspci' discards qualifiers from pointer target type
pcie.c:52: note: expected 'struct pci_dev *' but argument is of type 'const struct pci_dev *'

This patch fixes the issue.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>

Commit c9d95fbe "ARM: convert PCI defines
to variables" deleted cns3xxx' hardware.h, but didn't remove references
for it, so do it now.

This patch removes lines that refer to hardware.h.
Signed-off-by: Tommy Lin <tommy.lin.1101@gmail.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>

The TNET variant of DaVinci compiles some code that it shares
with other DaVinci variants, however it has a V6 CPU rather than
an ARM926T, thus the hardcoded call to arm926_flush_kern_cache_all()
in sleep.S will obviously fail, and we need to build with the
v6_flush_kern_cache_all() call instead. This was triggered by
manually altering the DaVinci config to build the TNET version.

Cc: Dave Martin <dave.martin@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Cc: stable@kernel.org

MDSTAT.STATE occupies bits 0..5 according to all available documentation, so fix
the #define MDSTAT_STATE_MASK at last. Using the wrong value seems to have been
harmless though...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

DA850/OMAP-L138 EMAC driver uses random mac address instead of
a fixed one because the mac address is not stuffed into EMAC
platform data.

This patch provides a function which reads the mac address
stored in SPI flash (registered as MTD device) and populates the
EMAC platform data. The function which reads the mac address is
registered as a callback which gets called upon addition of MTD
device.

NOTE: In case the MAC address stored in SPI flash is erased, follow
the instructions at [1] to restore it.

[1] http://processors.wiki.ti.com/index.php/GSG:_OMAP-L138_DVEVM_Additional_Procedures#Restoring_MAC_address_on_SPI_Flash

Modifications in v2:
Guarded registering the mtd_notifier only when MTD is enabled.
Earlier this was handled using mtd_has_partitions() call, but
this has been removed in Linux v3.0.

Modifications in v3:
a. Guarded da850_evm_m25p80_notify_add() function and
   da850evm_spi_notifier structure with CONFIG_MTD macros.
b. Renamed da850_evm_register_mtd_user() function to
   da850_evm_setup_mac_addr() and removed the struct mtd_notifier
   argument to this function.
c. Passed the da850evm_spi_notifier structure to register_mtd_user()
   function.

Modifications in v4:
Moved the da850_evm_setup_mac_addr() function within the first
CONFIG_MTD ifdef construct.
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Cc: stable@kernel.org

The suspend/resume _noirq handlers were #ifdef'd out in the
!CONFIG_SUSPEND case, but were still assigned to the dev_pm_ops
struct.  Fix by defining them to NULL in the !CONFIG_SUSPEND case.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Merge branches 'non_hwmod_compliant_fix_3.1rc', 'omap3_clock_fixes_3.1rc', 'omap4_clock_fixes_3.1rc', 'missing_2430_musb_adds_terminator_fix_3.1rc' and 'pwrdm_clkdm_fixes_3.1rc' into prcm-fixes-a-3.1rc

Add a missing array terminator to omap2430_usbhsotg_addrs[].  Without
this terminator, the omap_hwmod resource building code runs off the
end of the array, resulting in at least this error -- if not worse
behavior:

[    0.578002] musb-omap2430: failed to claim resource 4
[    0.583465] omap_device: musb-omap2430: build failed (-16)
[    0.589294] Could not build omap_device for musb-omap2430 usb_otg_hs

This should have been part of commit
78183f3f ("omap_hwmod: use a null
structure record to terminate omap_hwmod_addr_space arrays") but was
evidently missed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon/kms: make sure pci max read request size is valid on evergreen+ (v2)
  drm/radeon/kms: set a default max_pixel_clock

* 'for-linus' of git://oss.sgi.com/xfs/xfs:
  xfs: fix ->write_inode return values
  xfs: fix xfs_mark_inode_dirty during umount
  xfs: deprecate the nodelaylog mount option

If the bios or OS sets the pci max read request size to 0 or an
invalid value (6,7), it can result in a hang or slowdown.  Check
and set it to something sane if it's invalid.

Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=42162

v2: use pci reg defines from include/linux/pci_regs.h
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Currently we always redirty an inode that was attempted to be written out
synchronously but has been cleaned by an AIL pushed internall, which is
rather bogus.  Fix that by doing the i_update_core check early on and
return 0 for it.  Also include async calls for it, as doing any work for
those is just as pointless.  While we're at it also fix the sign for the
EIO return in case of a filesystem shutdown, and fix the completely
non-sensical locking around xfs_log_inode.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
(cherry picked from commit 297db93bb74cf687510313eb235a7aec14d67e97)
Signed-off-by: Alex Elder <aelder@sgi.com>

During umount we do not add a dirty inode to the lru and wait for it to
become clean first, but force writeback of data and metadata with
I_WILL_FREE set.  Currently there is no way for XFS to detect that the
inode has been redirtied for metadata operations, as we skip the
mark_inode_dirty call during teardown.  Fix this by setting i_update_core
nanually in that case, so that the inode gets flushed during inode reclaim.

Alternatively we could enable calling mark_inode_dirty for inodes in
I_WILL_FREE state, and let the VFS dirty tracking handle this.  I decided
against this as we will get better I/O patterns from reclaim compared to
the synchronous writeout in write_inode_now, and always marking the inode
dirty in some way from xfs_mark_inode_dirty is a better safetly net in
either case.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
(cherry picked from commit da6742a5a4cc844a9982fdd936ddb537c0747856)
Signed-off-by: Alex Elder <aelder@sgi.com>

* tag 'for_linus-20110831' of git://github.com/tytso/ext4:
  ext4: remove i_mutex lock in ext4_evict_inode to fix lockdep complaining

* 'for-linus' of git://neil.brown.name/md:
  md/raid5: fix a hang on device failure.
  md: fix clearing of 'blocked' flag in the presence of bad blocks.
  md/linear: avoid corrupting structure while waiting for rcu_free to complete.
  md: use REQ_NOIDLE flag in md_super_write()
  md: ensure changes to 'write-mostly' are reflected in metadata.
  md: report failure if a 'set faulty' request doesn't.

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/p1023rds: Fix the error of bank-width of nor flash
  powerpc/85xx: enable caam crypto driver by default
  powerpc/85xx: enable the audio drivers in the defconfigs

The i_mutex lock and flush_completed_IO() added by commit 2581fdc8
in ext4_evict_inode() causes lockdep complaining about potential
deadlock in several places.  In most/all of these LOCKDEP complaints
it looks like it's a false positive, since many of the potential
circular locking cases can't take place by the time the
ext4_evict_inode() is called; but since at the very least it may mask
real problems, we need to address this.

This change removes the flush_completed_IO() and i_mutex lock in
ext4_evict_inode().  Instead, we take a different approach to resolve
the software lockup that commit 2581fdc8 intends to fix.  Rather
than having ext4-dio-unwritten thread wait for grabing the i_mutex
lock of an inode, we use mutex_trylock() instead, and simply requeue
the work item if we fail to grab the inode's i_mutex lock.

This should speed up work queue processing in general and also
prevents the following deadlock scenario: During page fault,
shrink_icache_memory is called that in turn evicts another inode B.
Inode B has some pending io_end work so it calls ext4_ioend_wait()
that waits for inode B's i_ioend_count to become zero.  However, inode
B's ioend work was queued behind some of inode A's ioend work on the
same cpu's ext4-dio-unwritten workqueue.  As the ext4-dio-unwritten
thread on that cpu is processing inode A's ioend work, it tries to
grab inode A's i_mutex lock.  Since the i_mutex lock of inode A is
still hold before the page fault happened, we enter a deadlock.
Signed-off-by: Jiaying Zhang <jiayingz@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>

On some Power rv100 cards, we have no ATY OF table, but we have
no combios table either, and hence we refuse all modes on VGA-0
since we end up with a 0 max pixel clock.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cc: stable@kernel.org
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>

Waiting for a 'blocked' rdev to become unblocked in the raid5d thread
cannot work with internal metadata as it is the raid5d thread which
will clear the blocked flag.
This wasn't a problem in 3.0 and earlier as we only set the blocked
flag when external metadata was used then.
However we now set it always, so we need to be more careful.
Signed-off-by: NeilBrown <neilb@suse.de>

In the p1023rds, a physical bus of nor flash is 16 bits width.
The bank-width is width (in bytes) of the bus width. So, the
value of bank-width of nor flash is not one, and it should be
two.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

corenet based SoCs have SEC4 h/w, so enable the SEC4 driver,
caam, and the algorithms it supports, and disable the
SEC2/3 driver, talitos.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Enable the audio drivers in the non-corenet 85xx defconfigs so that audio
is enabled on the Freescale P1022DS reference board.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: Only Panther cheetah+ chips have POPC.

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/radeon/kms: add s/r quirk for Compaq Presario V5245EU
  drm/radeon/kms: evergreen & ni reset SPI block on CP resume
  drm: Fix the number of connector and encoder to cleanup functions

If there are no builtin users of find_next_bit_le() and
find_next_zero_bit_le(), these functions are not present in the kernel
image, causing m68k allmodconfig to fail with:

  ERROR: "find_next_zero_bit_le" [fs/ufs/ufs.ko] undefined!
  ERROR: "find_next_bit_le" [fs/udf/udf.ko] undefined!
  ...

This started to happen after commit 171d809d ("m68k: merge mmu and
non-mmu bitops.h"), as m68k had its own inline versions before.

commit 63e424c8 ("arch: remove CONFIG_GENERIC_FIND_{NEXT_BIT,
BIT_LE, LAST_BIT}") added find_last_bit.o to obj-y (so it's always
included), but find_next_bit.o to lib-y (so it gets removed by the
linker if there are no builtin users).
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fixes resume on Compaq Presario V5245EU.

Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=41642Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

For some reason SPI block is in broken state after module
unloading. This lead to broken rendering after reloading
module. Fix this by reseting SPI block in CP resume function

Signed-off-by: Jerome Glisse <jglisse@redhat.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

When the 'blocked' flag on a device is cleared while there are
unacknowledged bad blocks we must fail the device.  This is needed for
backwards compatability of the interface.

The code currently uses the wrong test for "unacknowledged bad blocks
exist".  Change it to the right test.
Signed-off-by: NeilBrown <neilb@suse.de>

Signed-off-by: David S. Miller <davem@davemloft.net>

* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
  ARM: pm: avoid writing the auxillary control register for ARMv7
  ARM: pm: some ARMv7 requires a dsb in resume to ensure correctness
  ARM: pm: arm920/926: fix number of registers saved
  ARM: pm: CPU specific code should not overwrite r1 (v:p offset)
  ARM: 7066/1: proc-v7: disable SCTLR.TE when disabling MMU
  ARM: 7065/1: kexec: ensure new kernel is entered in ARM state
  ARM: 7003/1: vexpress: Add clock definition for the SP805.
  ARM: 7051/1: cpuimx* boards: fix mach-types errors
  ARM: 7019/1: Footbridge: select CLKEVT_I8253 for ARCH_NETWINDER
  ARM: 7015/1: ARM errata: Possible cache data corruption with hit-under-miss enabled
  ARM: 7014/1: cache-l2x0: Fix L2 Cache size calculation.
  ARM: 6967/1: ep93xx: ts72xx: fix board model detection
  ARM: 6965/1: ep93xx: add model detection for ts-7300 and ts-7400 boards
  ARM: cache: detect VIPT aliasing I-cache on ARMv6
  ARM: twd: register clockevents device before enabling PPI
  ARM: realview: ensure visibility of writes during reset
  ARM: perf: make name of arm_pmu_type consistent
  ARM: perf: fix prototype of release_pmu
  ARM: fix perf build with uclibc toolchains

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
  ARM: mach-footbridge: add missing header file <video/vga.h>
  ARM: mach-orion5x: add missing header file <linux/vga.h>
  arm: fix compile failure in orion5x/dns323-setup.c
  at91: at91sam9261.c: fix typo in t2_clk alias for atmel_tcb.0
  ARM: S5P: fix bug in spdif_clk_get_rate
  ARM: EXYNOS4: Add restart hook for proper reboot
  ARM: EXYNOS4: Increase reset delay for USB HOST PHY
  ARM: S5P: add required chained_irq_enter/exit to gpio-int code
  ARM: EXYNOS4: add required chained_irq_enter/exit to eint code
  ARM: SAMSUNG: Add chained enrty/exit call to timer interrupt handler
  ARM: S3C64XX: Fix build break in PM debug
  ARM: S5PV210: Fix build warning
  ARM: EXYNOS4: Fix the IRQ definitions for MIPI CSIS device
  ARM: EXYNOS4: remove duplicated inclusion
  ARM: EXYNOS4: Fix wrong devname to support clkdev
  ARM: EXYNOS4: Use the correct regulator names on universal_c210
  ARM: SAMSUNG: Fix Section mismatch in samsung_bl_set()
  ARM: S5P64X0: Replace irq_gc_ack() with irq_gc_ack_set_bit()

These were missed in commit f5b94099 "All Arch: remove linkage
for sys_nfsservctl system call" due to them having no sys_ prefix
(presumably).

Cc: NeilBrown <neilb@suse.de>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-parisc@vger.kernel.org
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: James Bottomley <James.Bottomley@hansenpartnership.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (42 commits)
  netpoll: fix incorrect access to skb data in __netpoll_rx
  cassini: init before use in cas_interruptN.
  can: ti_hecc: Fix uninitialized spinlock in probe
  can: ti_hecc: Fix unintialized variable
  net: sh_eth: fix the compile error
  net/phy: fix DP83865 phy interrupt handler
  sendmmsg/sendmsg: fix unsafe user pointer access
  ibmveth: Fix leak when recycling skb and hypervisor returns error
  arp: fix rcu lockdep splat in arp_process()
  bridge: fix a possible use after free
  bridge: Pseudo-header required for the checksum of ICMPv6
  mcast: Fix source address selection for multicast listener report
  MAINTAINERS: Update GIT trees for network development
  ath9k: Fix PS wrappers in ath9k_set_coverage_class
  carl9170: Fix mismatch in carl9170_op_set_key mutex lock-unlock
  wl12xx: add max_sched_scan_ssids value to the hw description
  wl12xx: Fix validation of pm_runtime_get_sync return value
  wl12xx: Remove obsolete testmode NVS push command
  bcma: add uevent to the bus, to autoload drivers
  ath9k_hw: Fix STA (AR9485) bringup issue due to incorrect MAC address
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc32,sun4d: Change IPI IRQ level to prevent collision between IPI and timer interrupt
  sparc: Remove another reference to nfsservctl

Merge branch 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-3.x

* 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-3.x:
  ARM: mach-shmobile: sh7372 CMT3 and CMT4 clock support
  ARM: mach-shmobile: sh7372 MSIOF clock support
  ARM: mach-shmobile: clock-sh7372: fixup USB-DMAC1 settings
  ARM: mach-shmobile: clock-sh73a0: tidyup CKSCR main clock selecter
  ARM: mach-shmobile: Remove 3DG/SGX from sh7372 INTCS
  ARM: mach-shmobile: mackerel: Add USB-DMA ID
  mmc: sdhi, mmcif: zboot: Correct clock disable logic
  ARM: mach-shmobile: ag5evm: SDHI requires waiting for idle
  ARM: static should be at beginning of declaration
  ARM: mach-shmobile: Use CMT2 for timer on sh7372
  ARM: mach-shmobile: sh7372: Add USB-DMAC support