- 18 Apr, 2023 10 commits
-
-
Johannes Berg authored
Track instead whether or not the station was authorized, that's clearer than trying to indicate in the code whether or not the full bandwidth should be used via an 'update' argument. While at it, give rs_fw_rate_init() the iwl_mvm_ prefix. Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
Gregory Greenman <gregory.greenman@intel.com> Link: https://lore.kernel.org/r/20230417113648.92bd8d36e311.I1877a109104d5ffeaaad6a623e89f0c44decc38e@changeidSigned-off-by:
-
Johannes Berg authored
When allocating a new link station, initialize the ratescaling data for it. To do that, refactor the initialization code out into a new iwl_mvm_rs_add_sta_link() function. Signed-off-by:
-
Johannes Berg authored
We need to look up the correct version of this struct depending on the interface type, rather than just checking if the pointer is non-NULL. Fix that. Fixes: befebbb3 ("iwlwifi: rs: consider LDPC capability in case of HE") Fixes: b009cf71 ("iwlwifi: mvm: only enable HE DCM if we also support TX") Signed-off-by:
-
Johannes Berg authored
Since only clients to an AP can be 20MHz-only STAs, adjust the code to not make the use of EHT capabilities depend on only the bandwidth, but also the type of interface. Fixes: 701404f1 ("wifi: iwlwifi: rs: add support for parsing max MCS per NSS/BW in 11be") Signed-off-by:
-
Johannes Berg authored
When this is called it might crash due to the use of deflink's phy context, update all links instead. It really shouldn't be called right now though, but it's better to have safer code until we update this to be with a link parameter. Signed-off-by:
-
Johannes Berg authored
When we first add the STA before sending an authentication frame this is false. However, in some cases such as FT or certainly in MLO link switch scenarios, it will be true. If it happens to be true, it causes a firmware assert (in LMAC, 0x2528), because the same bit is used by the firmware for tracking this setting as well as for tracking if the management key has been installed, and then we get this assert from the firmware when installing the MFP key as it thinks it has already been installed. Remove the setting for now, until the firmware disentangles the two. We should be able to set it, in fact we should be setting it speculatively before authentication/association, to avoid processing management frames that should have been protected/encrypted before the key is set. Signed-off-by:
-
Johannes Berg authored
We can allow NL80211_EXT_FEATURE_SCAN_MIN_PREQ_CONTENT since we just use the elements from mac80211. Signed-off-by:
-
Johannes Berg authored
A long time, ago in commit 818965d3 ("cfg80211: Allow a scan request for a specific BSSID"), the stack started passing the BSSID that should be scanned for. Use it in iwlwifi for the intended optimisation, and to also allow the use of this for an implementation sending multi-link probe requests. Signed-off-by:
-
Gregory Greenman authored
The restriction where MAC ID 0 could be used only for the managed/IBSS vif is not required when using the new MLO FW API. Update the driver. Signed-off-by:
-
Emmanuel Grumbach authored
The firmware no longer wants the beacon template inside the MAC command. Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
- 17 Apr, 2023 27 commits
-
-
Po-Hao Huang authored
Add iface_combination declaration to enable concurrent mode. Only two interfaces under same frequency is supported currently. We limit the role combination to be STA + P2P or STA + AP only for now until new feature is requested. Signed-off-by:
Po-Hao Huang <phhuang@realtek.com> Signed-off-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230415035016.15788-2-pkshih@realtek.com
-
Po-Hao Huang authored
Power saving for more than one station is not supported currently. Disallow entering PS mode when we have more than one associated stations. Signed-off-by:
-
Po-Hao Huang authored
Since firmware can't have proper statistics, driver update the statistics periodically to firmware to assist in tuning performance. Signed-off-by:
-
Ping-Ke Shih authored
Remove macros that set H2C data. Instead, use struct and le32_encode_bits() with mask definition to make it clean. Signed-off-by:
-
Po-Hao Huang authored
Since we can get the current channel definition each interface maps to, remove store_op function that is no longer required to make things simple. Signed-off-by:
-
Chih-Kang Chang authored
Mac80211 core may ask driver to change to idle mode during HW scan, then H2C command for HW scan will send failed since chip is in idle mode. Therefore, We check the SCANNING flag before entering IPS to prevent this behavior. Signed-off-by:
Chih-Kang Chang <gary.chang@realtek.com> Signed-off-by:
-
Ping-Ke Shih authored
8851B has various hardware module types, so BT coexistence in firmware needs these information to make decision. Add them to make 8851B work well. Signed-off-by:
-
Ching-Te Ku authored
Correct Bluetooth RSSI count method. The 6dB is the gap between hardware packet sampled value and real RSSI value. Signed-off-by:
Ching-Te Ku <ku920601@realtek.com> Signed-off-by:
-
Ching-Te Ku authored
Chips use similar hardware for path control, but could different path/antenna configuration. Add these register to monitor, if there are wrong settings, these register can help to debug. Signed-off-by:
-
Ching-Te Ku authored
When Wi-Fi & Bluetooth are both busy at the same time, Wi-Fi need to enable RX gain to protect Wi-Fi RX RF ability. Without this configure the interference from Bluetooth will bring a big impact to Wi-Fi RX. Signed-off-by:
-
Chih-Kang Chang authored
In WoWLAN Mode, it's expected that WiFi chip could enter power save mode only after all setting is finished, but current wow_enter_lps function break the rule and may lead to WoWLAN function fail in low probability, so fix it. Signed-off-by:
-
Chin-Yen Lee authored
To support WoWLAN mode for 8852be, we add one PLE quota setting and WoWLAN stub, which shows that supported WLAN events include receiving magic packet, rekey packet and deauth packet, and disconnecting from AP. Signed-off-by:
Chin-Yen Lee <timlee@realtek.com> Signed-off-by:
-
Golan Ben Ami authored
This is noising the kernel log and customers asked to hush it down. We can live with this message in "info" verbosity. Signed-off-by:
Golan Ben Ami <golan.ben.ami@intel.com> Signed-off-by:
-
Emmanuel Grumbach authored
Since we didn't reset t to 0, only the first iteration of the loop did checked the ready bit several times. From the second iteration and on, we just tested the bit once and continued to the next iteration. Reported-and-tested-by:
Lorenzo Zolfanelli <lorenzo@zolfa.nl> Link: https://bugzilla.kernel.org/show_bug.cgi?id=216452 Fixes: 289e5501 ("iwlwifi: fix the preparation of the card") Signed-off-by:
-
Johannes Berg authored
Newer firmware images have a TLV advertising how many beacons they support, use that to permit adding more links in AP mode (FW needs to support at least as many links as beacons). Signed-off-by:
-
Johannes Berg authored
Implement switching keys from one set of firmware station IDs to another set, during link switch. Signed-off-by:
-
Johannes Berg authored
When we switch station links, also add the code to switch BAIDs from one station mask to the new one. To do so, refactor the switching code a bit to have common code for all the needed switches; will add keys next. Signed-off-by:
-
Johannes Berg authored
When we have MLO connections, a BAID applies to multiple firmware stations. Track the station mask instead of the station ID, getting rid of a few more deflink cases and preparing for handling link switching for BAIDs. Signed-off-by:
-
Gregory Greenman authored
Start supporting API version 77 for AX devices. Signed-off-by:
-
Johannes Berg authored
When we remove a queue we need to use the currently active firmware stations in the mask, not the deflink one. Fix that. Signed-off-by:
-
Avraham Stern authored
The initiator smooth list is initialized only in iwl_mvm_up(), but is cleared in iwl_mvm_mac_stop. This may result in iterating over the list before it was initialized in case iwl_mvm_up() failed early. Fix it by moving the list initialization to an earlier stage. Fixes: b68bd2e3 ("iwlwifi: mvm: Add FTM initiator RTT smoothing logic") Signed-off-by:
Avraham Stern <avraham.stern@intel.com> Signed-off-by:
-
Johannes Berg authored
We are going to need this in more places than just the key code, so factor out the functionality of getting the FW station ID mask (filtered to a specific link if needed) to a separate function that can now be called both under RCU and mvm->mutex protection. Signed-off-by:
-
Johannes Berg authored
The firmware split the HE support field into HE and "pseudo HE", the latter is really for AP and doesn't implement trigger frame handling for example. Use the new field for AP mode. Signed-off-by:
-
Ilan Peer authored
The usage of the 'dtim_period' value was wrong, as it is only a multiplier of the beacon interval, and thus, beacon interval should also be considered. Fix it. Signed-off-by:
Ilan Peer <ilan.peer@intel.com> Signed-off-by:
-
Johannes Berg authored
In iwl_mvm_mac_ctxt_get_lowest_rate() we were still accessing vif->bss_conf without any multi-link provisions, and also the info->band, both of which isn't valid in MLO. Fix the code to look at the correct link. In case of EAPOL transmissions for the initial 4-way-HS, look up the correct link here as well, and warn if multiple are active. Signed-off-by:
-
Gregory Greenman authored
When rx/tx queues are being freed, on a different CPU there could be still rx flow running. Call napi_synchronize() to prevent such a race. Signed-off-by:
Benjamin Berg <benjamin.berg@intel.com> Signed-off-by:
-
Johannes Berg authored
For some devices, in client mode, we support full bandwidth uplink multi-user MIMO. Add the necessary capability. Signed-off-by:
-
- 14 Apr, 2023 3 commits
-
-
Rob Herring authored
bcma/main.c uses of_dma_configure() which is declared in of_device.h. of_device.h gets implicitly included by of_platform.h, but that is going to be removed soon. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Bitterblue Smith authored
Handle them the same way as the devices with 3-4 USB out endpoints. This is needed for the RTL8192FU. Signed-off-by:
Bitterblue Smith <rtl8821cerfe2@gmail.com> Reviewed-by:
-
Bitterblue Smith authored
Add some new members to rtl8xxxu_fileops and use them instead of checking priv->rtl_chip. Signed-off-by:
-
