In Clause 5 of IEEE Std 802-2014, two sublayers of the data link layer
(DLL) of the Open Systems Interconnection basic reference model (OSI/RM)
are described; the medium access control (MAC) and logical link control
(LLC) sublayers. The MAC sublayer is the one facing the physical layer.

In 8.2 of IEEE Std 802.1Q-2022, the Bridge architecture is described. A
Bridge component comprises a MAC Relay Entity for interconnecting the Ports
of the Bridge, at least two Ports, and higher layer entities with at least
a Spanning Tree Protocol Entity included.

Each Bridge Port also functions as an end station and shall provide the MAC
Service to an LLC Entity. Each instance of the MAC Service is provided to a
distinct LLC Entity that supports protocol identification, multiplexing,
and demultiplexing, for protocol data unit (PDU) transmission and reception
by one or more higher layer entities.

It is described in 8.13.9 of IEEE Std 802.1Q-2022 that in a Bridge, the LLC
Entity associated with each Bridge Port is modeled as being directly
connected to the attached Local Area Network (LAN).

On the switch with CPU port architecture, CPU port functions as Management
Port, and the Management Port functionality is provided by software which
functions as an end station. Software is connected to an IEEE 802 LAN that
is wholly contained within the system that incorporates the Bridge.
Software provides access to the LLC Entity associated with each Bridge Port
by the value of the source port field on the special tag on the frame
received by software.

We call frames that carry control information to determine the active
topology and current extent of each Virtual Local Area Network (VLAN),
i.e., spanning tree or Shortest Path Bridging (SPB) and Multiple VLAN
Registration Protocol Data Units (MVRPDUs), and frames from other link
constrained protocols, such as Extensible Authentication Protocol over LAN
(EAPOL) and Link Layer Discovery Protocol (LLDP), link-local frames. They
are not forwarded by a Bridge. Permanently configured entries in the
filtering database (FDB) ensure that such frames are discarded by the
Forwarding Process. In 8.6.3 of IEEE Std 802.1Q-2022, this is described in
detail:

Each of the reserved MAC addresses specified in Table 8-1
(01-80-C2-00-00-[00,01,02,03,04,05,06,07,08,09,0A,0B,0C,0D,0E,0F]) shall be
permanently configured in the FDB in C-VLAN components and ERs.

Each of the reserved MAC addresses specified in Table 8-2
(01-80-C2-00-00-[01,02,03,04,05,06,07,08,09,0A,0E]) shall be permanently
configured in the FDB in S-VLAN components.

Each of the reserved MAC addresses specified in Table 8-3
(01-80-C2-00-00-[01,02,04,0E]) shall be permanently configured in the FDB
in TPMR components.

The FDB entries for reserved MAC addresses shall specify filtering for all
Bridge Ports and all VIDs. Management shall not provide the capability to
modify or remove entries for reserved MAC addresses.

The addresses in Table 8-1, Table 8-2, and Table 8-3 determine the scope of
propagation of PDUs within a Bridged Network, as follows:

  The Nearest Bridge group address (01-80-C2-00-00-0E) is an address that
  no conformant Two-Port MAC Relay (TPMR) component, Service VLAN (S-VLAN)
  component, Customer VLAN (C-VLAN) component, or MAC Bridge can forward.
  PDUs transmitted using this destination address, or any other addresses
  that appear in Table 8-1, Table 8-2, and Table 8-3
  (01-80-C2-00-00-[00,01,02,03,04,05,06,07,08,09,0A,0B,0C,0D,0E,0F]), can
  therefore travel no further than those stations that can be reached via a
  single individual LAN from the originating station.

  The Nearest non-TPMR Bridge group address (01-80-C2-00-00-03), is an
  address that no conformant S-VLAN component, C-VLAN component, or MAC
  Bridge can forward; however, this address is relayed by a TPMR component.
  PDUs using this destination address, or any of the other addresses that
  appear in both Table 8-1 and Table 8-2 but not in Table 8-3
  (01-80-C2-00-00-[00,03,05,06,07,08,09,0A,0B,0C,0D,0F]), will be relayed
  by any TPMRs but will propagate no further than the nearest S-VLAN
  component, C-VLAN component, or MAC Bridge.

  The Nearest Customer Bridge group address (01-80-C2-00-00-00) is an
  address that no conformant C-VLAN component, MAC Bridge can forward;
  however, it is relayed by TPMR components and S-VLAN components. PDUs
  using this destination address, or any of the other addresses that appear
  in Table 8-1 but not in either Table 8-2 or Table 8-3
  (01-80-C2-00-00-[00,0B,0C,0D,0F]), will be relayed by TPMR components and
  S-VLAN components but will propagate no further than the nearest C-VLAN
  component or MAC Bridge.

Because the LLC Entity associated with each Bridge Port is provided via CPU
port, we must not filter these frames but forward them to CPU port.

In a Bridge, the transmission Port is majorly decided by ingress and egress
rules, FDB, and spanning tree Port State functions of the Forwarding
Process. For link-local frames, only CPU port should be designated as
destination port in the FDB, and the other functions of the Forwarding
Process must not interfere with the decision of the transmission Port. We
call this process trapping frames to CPU port.

Therefore, on the switch with CPU port architecture, link-local frames must
be trapped to CPU port, and certain link-local frames received by a Port of
a Bridge comprising a TPMR component or an S-VLAN component must be
excluded from it.

A Bridge of the switch with CPU port architecture cannot comprise a
Two-Port MAC Relay (TPMR) component as a TPMR component supports only a
subset of the functionality of a MAC Bridge. A Bridge comprising two Ports
(Management Port doesn't count) of this architecture will either function
as a standard MAC Bridge or a standard VLAN Bridge.

Therefore, a Bridge of this architecture can only comprise S-VLAN
components, C-VLAN components, or MAC Bridge components. Since there's no
TPMR component, we don't need to relay PDUs using the destination addresses
specified on the Nearest non-TPMR section, and the proportion of the
Nearest Customer Bridge section where they must be relayed by TPMR
components.

One option to trap link-local frames to CPU port is to add static FDB
entries with CPU port designated as destination port. However, because that
Independent VLAN Learning (IVL) is being used on every VID, each entry only
applies to a single VLAN Identifier (VID). For a Bridge comprising a MAC
Bridge component or a C-VLAN component, there would have to be 16 times
4096 entries. This switch intellectual property can only hold a maximum of
2048 entries. Using this option, there also isn't a mechanism to prevent
link-local frames from being discarded when the spanning tree Port State of
the reception Port is discarding.

The remaining option is to utilise the BPC, RGAC1, RGAC2, RGAC3, and RGAC4
registers. Whilst this applies to every VID, it doesn't contain all of the
reserved MAC addresses without affecting the remaining Standard Group MAC
Addresses. The REV_UN frame tag utilised using the RGAC4 register covers
the remaining 01-80-C2-00-00-[04,05,06,07,08,09,0A,0B,0C,0D,0F] destination
addresses. It also includes the 01-80-C2-00-00-22 to 01-80-C2-00-00-FF
destination addresses which may be relayed by MAC Bridges or VLAN Bridges.
The latter option provides better but not complete conformance.

This switch intellectual property also does not provide a mechanism to trap
link-local frames with specific destination addresses to CPU port by
Bridge, to conform to the filtering rules for the distinct Bridge
components.

Therefore, regardless of the type of the Bridge component, link-local
frames with these destination addresses will be trapped to CPU port:

01-80-C2-00-00-[00,01,02,03,0E]

In a Bridge comprising a MAC Bridge component or a C-VLAN component:

  Link-local frames with these destination addresses won't be trapped to
  CPU port which won't conform to IEEE Std 802.1Q-2022:

  01-80-C2-00-00-[04,05,06,07,08,09,0A,0B,0C,0D,0F]

In a Bridge comprising an S-VLAN component:

  Link-local frames with these destination addresses will be trapped to CPU
  port which won't conform to IEEE Std 802.1Q-2022:

  01-80-C2-00-00-00

  Link-local frames with these destination addresses won't be trapped to
  CPU port which won't conform to IEEE Std 802.1Q-2022:

  01-80-C2-00-00-[04,05,06,07,08,09,0A]

Currently on this switch intellectual property, if the spanning tree Port
State of the reception Port is discarding, link-local frames will be
discarded.

To trap link-local frames regardless of the spanning tree Port State, make
the switch regard them as Bridge Protocol Data Units (BPDUs). This switch
intellectual property only lets the frames regarded as BPDUs bypass the
spanning tree Port State function of the Forwarding Process.

With this change, the only remaining interference is the ingress rules.
When the reception Port has no PVID assigned on software, VLAN-untagged
frames won't be allowed in. There doesn't seem to be a mechanism on the
switch intellectual property to have link-local frames bypass this function
of the Forwarding Process.

Fixes: b8f126a8 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240409-b4-for-net-mt7530-fix-link-local-when-stp-discarding-v2-1-07b1150164ac@arinc9.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

This reverts commit 58effa34.
Review was not finished on this patch. So it's not ready for
upstreaming.
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Link: https://lore.kernel.org/r/20240409113753.2181368-1-gbayer@linux.ibm.com
Fixes: 58effa34 ("s390/ism: fix receive message buffer allocation")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

The wrong port config is being used if the PCS is reconfigured. Fix this
by correctly using the new config instead of the old one.

Fixes: 946e7fd5 ("net: sparx5: add port module support")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240409-link-mode-reconfiguration-fix-v2-1-db6a507f3627@microchip.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

A couple of debug functions use a 512 byte temporary buffer and call another
function that has another buffer of the same size, which in turn exceeds the
usual warning limit for excessive stack usage:

drivers/net/ethernet/mellanox/mlx5/core/steering/dr_dbg.c:1073:1: error: stack frame size (1448) exceeds limit (1024) in 'dr_dump_start' [-Werror,-Wframe-larger-than]
dr_dump_start(struct seq_file *file, loff_t *pos)
drivers/net/ethernet/mellanox/mlx5/core/steering/dr_dbg.c:1009:1: error: stack frame size (1120) exceeds limit (1024) in 'dr_dump_domain' [-Werror,-Wframe-larger-than]
dr_dump_domain(struct seq_file *file, struct mlx5dr_domain *dmn)
drivers/net/ethernet/mellanox/mlx5/core/steering/dr_dbg.c:705:1: error: stack frame size (1104) exceeds limit (1024) in 'dr_dump_matcher_rx_tx' [-Werror,-Wframe-larger-than]
dr_dump_matcher_rx_tx(struct seq_file *file, bool is_rx,

Rework these so that each of the various code paths only ever has one of
these buffers in it, and exactly the functions that declare one have
the 'noinline_for_stack' annotation that prevents them from all being
inlined into the same caller.

Fixes: 917d1e79 ("net/mlx5: DR, Change SWS usage to debug fs seq_file interface")
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/all/20240219100506.648089-1-arnd@kernel.org/Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240408074142.3007036-1-arnd@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Tariq Toukan says:

====================
mlx5 misc fixes

This patchset provides bug fixes to mlx5 driver.

This is V2 of the series previously submitted as PR by Saeed:
https://lore.kernel.org/netdev/20240326144646.2078893-1-saeed@kernel.org/T/

Series generated against:
commit 237f3cf1 ("xsk: validate user input for XDP_{UMEM|COMPLETION}_FILL_RING")
====================

Link: https://lore.kernel.org/r/20240409190820.227554-1-tariqt@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Adaptations need to be made for the auxiliary device management in the
core driver level. Block this combination for now.

Fixes: 678eb448 ("net/mlx5: SD, Implement basic query and instantiation")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Link: https://lore.kernel.org/r/20240409190820.227554-12-tariqt@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When supporting more than 128 channels, the RQT size is
calculated by multiplying the number of channels by 2
and rounding up to the nearest power of 2.

The index of the RQT is derived from the RSS hash
calculations. If XOR8 is used as the RSS hash function,
there are only 256 possible hash results, and therefore,
only 256 indexes can be reached in the RQT.

Block setting the RSS hash function to XOR when the number
of channels exceeds 128.

Fixes: 74a8dada ("net/mlx5e: Preparations for supporting larger number of channels")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240409190820.227554-11-tariqt@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Free Tx port timestamping metadata entries in the NAPI poll context and
consume metadata enties in the WQE xmit path. Do not free a Tx port
timestamping metadata entry in the WQE xmit path even in the error path to
avoid a race between two metadata entry producers.

Fixes: 3178308a ("net/mlx5e: Make tx_port_ts logic resilient to out-of-order CQEs")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240409190820.227554-10-tariqt@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When creating a new HTB class while the interface is down,
the variable that follows the number of QoS SQs (htb_max_qos_sqs)
may not be consistent with the number of HTB classes.

Previously, we compared these two values to ensure that
the node_qid is lower than the number of QoS SQs, and we
allocated stats for that SQ when they are equal.

Change the check to compare the node_qid with the current
number of leaf nodes and fix the checking conditions to
ensure allocation of stats_list and stats for each node.

Fixes: 214baf22 ("net/mlx5e: Support HTB offload")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240409190820.227554-9-tariqt@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When mlx5e_priv_init() fails, the cleanup flow calls mlx5e_selq_cleanup which
calls mlx5e_selq_apply() that assures that the `priv->state_lock` is held using
lockdep_is_held().

Acquire the state_lock in mlx5e_selq_cleanup().

Kernel log:
=============================
WARNING: suspicious RCU usage
6.8.0-rc3_net_next_841a9b5 #1 Not tainted
-----------------------------
drivers/net/ethernet/mellanox/mlx5/core/en/selq.c:124 suspicious rcu_dereference_protected() usage!

other info that might help us debug this:

rcu_scheduler_active = 2, debug_locks = 1
2 locks held by systemd-modules/293:
 #0: ffffffffa05067b0 (devices_rwsem){++++}-{3:3}, at: ib_register_client+0x109/0x1b0 [ib_core]
 #1: ffff8881096c65c0 (&device->client_data_rwsem){++++}-{3:3}, at: add_client_context+0x104/0x1c0 [ib_core]

stack backtrace:
CPU: 4 PID: 293 Comm: systemd-modules Not tainted 6.8.0-rc3_net_next_841a9b5 #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Call Trace:
 <TASK>
 dump_stack_lvl+0x8a/0xa0
 lockdep_rcu_suspicious+0x154/0x1a0
 mlx5e_selq_apply+0x94/0xa0 [mlx5_core]
 mlx5e_selq_cleanup+0x3a/0x60 [mlx5_core]
 mlx5e_priv_init+0x2be/0x2f0 [mlx5_core]
 mlx5_rdma_setup_rn+0x7c/0x1a0 [mlx5_core]
 rdma_init_netdev+0x4e/0x80 [ib_core]
 ? mlx5_rdma_netdev_free+0x70/0x70 [mlx5_core]
 ipoib_intf_init+0x64/0x550 [ib_ipoib]
 ipoib_intf_alloc+0x4e/0xc0 [ib_ipoib]
 ipoib_add_one+0xb0/0x360 [ib_ipoib]
 add_client_context+0x112/0x1c0 [ib_core]
 ib_register_client+0x166/0x1b0 [ib_core]
 ? 0xffffffffa0573000
 ipoib_init_module+0xeb/0x1a0 [ib_ipoib]
 do_one_initcall+0x61/0x250
 do_init_module+0x8a/0x270
 init_module_from_file+0x8b/0xd0
 idempotent_init_module+0x17d/0x230
 __x64_sys_finit_module+0x61/0xb0
 do_syscall_64+0x71/0x140
 entry_SYSCALL_64_after_hwframe+0x46/0x4e
 </TASK>

Fixes: 8bf30be7 ("net/mlx5e: Introduce select queue parameters")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240409190820.227554-8-tariqt@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Changing the channels number after configuring the receive flow hash
indirection table may affect the RSS table size. The previous
configuration may no longer be compatible with the new receive flow
hash indirection table.

Block changing the channels number when RXFH is configured and changing
the channels number requires resizing the RSS table size.

Fixes: 74a8dada ("net/mlx5e: Preparations for supporting larger number of channels")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240409190820.227554-7-tariqt@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

struct mlx5_pkt_reformat contains a naked union of a u32 id and a
dr_action pointer which is used when the action is SW-managed (when
pkt_reformat.owner is set to MLX5_FLOW_RESOURCE_OWNER_SW). Using id
directly in that case is incorrect, as it maps to the least significant
32 bits of the 64-bit pointer in mlx5_fs_dr_action and not to the pkt
reformat id allocated in firmware.

For the purpose of comparing whether two rules are identical,
interpreting the least significant 32 bits of the mlx5_fs_dr_action
pointer as an id mostly works... until it breaks horribly and produces
the outcome described in [1].

This patch fixes mlx5_flow_dests_cmp to correctly compare ids using
mlx5_fs_dr_action_get_pkt_reformat_id for the SW-managed rules.

Link: https://lore.kernel.org/netdev/ea5264d6-6b55-4449-a602-214c6f509c1e@163.com/T/#u [1]

Fixes: 6a48faee ("net/mlx5: Add direct rule fs_cmd implementation")
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240409190820.227554-6-tariqt@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Previously, add_rule_fg would only add newly created rules from the
handle into the tree when they had a refcount of 1. On the other hand,
create_flow_handle tries hard to find and reference already existing
identical rules instead of creating new ones.

These two behaviors can result in a situation where create_flow_handle
1) creates a new rule and references it, then
2) in a subsequent step during the same handle creation references it
   again,
resulting in a rule with a refcount of 2 that is not linked into the
tree, will have a NULL parent and root and will result in a crash when
the flow group is deleted because del_sw_hw_rule, invoked on rule
deletion, assumes node->parent is != NULL.

This happened in the wild, due to another bug related to incorrect
handling of duplicate pkt_reformat ids, which lead to the code in
create_flow_handle incorrectly referencing a just-added rule in the same
flow handle, resulting in the problem described above. Full details are
at [1].

This patch changes add_rule_fg to add new rules without parents into
the tree, properly initializing them and avoiding the crash. This makes
it more consistent with how rules are added to an FTE in
create_flow_handle.

Fixes: 74491de9 ("net/mlx5: Add multi dest support")
Link: https://lore.kernel.org/netdev/ea5264d6-6b55-4449-a602-214c6f509c1e@163.com/T/#u [1]
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240409190820.227554-5-tariqt@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The mlx5 comp irq name scheme is changed a little bit between
commit 3663ad34 ("net/mlx5: Shift control IRQ to the last index")
and commit 3354822c ("net/mlx5: Use dynamic msix vectors allocation").
The index in the comp irq name used to start from 0 but now it starts
from 1. There is nothing critical here, but it's harmless to change
back to the old behavior, a.k.a starting from 0.

Fixes: 3354822c ("net/mlx5: Use dynamic msix vectors allocation")
Reviewed-by: Mohamed Khalfella <mkhalfella@purestorage.com>
Reviewed-by: Yuanyuan Zhong <yzhong@purestorage.com>
Signed-off-by: Michael Liang <mliang@purestorage.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240409190820.227554-4-tariqt@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

In case device is having a non fatal FW error during probe, the
driver will report the error to user via devlink. This will trigger
a WARN_ON, since mlx5 is calling devlink_register() last.
In order to avoid the WARN_ON[1], change mlx5 to invoke devl_register()
first under devlink lock.

[1]
WARNING: CPU: 5 PID: 227 at net/devlink/health.c:483 devlink_recover_notify.constprop.0+0xb8/0xc0
CPU: 5 PID: 227 Comm: kworker/u16:3 Not tainted 6.4.0-rc5_for_upstream_min_debug_2023_06_12_12_38 #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Workqueue: mlx5_health0000:08:00.0 mlx5_fw_reporter_err_work [mlx5_core]
RIP: 0010:devlink_recover_notify.constprop.0+0xb8/0xc0
Call Trace:
 <TASK>
 ? __warn+0x79/0x120
 ? devlink_recover_notify.constprop.0+0xb8/0xc0
 ? report_bug+0x17c/0x190
 ? handle_bug+0x3c/0x60
 ? exc_invalid_op+0x14/0x70
 ? asm_exc_invalid_op+0x16/0x20
 ? devlink_recover_notify.constprop.0+0xb8/0xc0
 devlink_health_report+0x4a/0x1c0
 mlx5_fw_reporter_err_work+0xa4/0xd0 [mlx5_core]
 process_one_work+0x1bb/0x3c0
 ? process_one_work+0x3c0/0x3c0
 worker_thread+0x4d/0x3c0
 ? process_one_work+0x3c0/0x3c0
 kthread+0xc6/0xf0
 ? kthread_complete_and_exit+0x20/0x20
 ret_from_fork+0x1f/0x30
 </TASK>

Fixes: cf530217 ("devlink: Notify users when objects are accessible")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240409190820.227554-3-tariqt@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Next patch will move devlink register to be first. Therefore, whenever
mlx5 will register a param, the user will be notified.
In order to notify the user, devlink is using the get() callback of
the param. Hence, resources that are being used by the get() callback
must be set before the devlink param is registered.

Therefore, store eswitch pointer inside mdev before registering the
param.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240409190820.227554-2-tariqt@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

In my recent commit, I missed that do_replace() handlers
use copy_from_sockptr() (which I fixed), followed
by unsafe copy_from_sockptr_offset() calls.

In all functions, we can perform the @optlen validation
before even calling xt_alloc_table_info() with the following
check:

if ((u64)optlen < (u64)tmp.size + sizeof(tmp))
        return -EINVAL;

Fixes: 0c83842d ("netfilter: validate user input for expected length")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Pablo Neira Ayuso <pablo@netfilter.org>
Link: https://lore.kernel.org/r/20240409120741.3538135-1-edumazet@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add missing dependency on CONFIG_R8169_LEDS. As-is a link error occurs
if config option CONFIG_R8169_LEDS isn't enabled.

Fixes: 19fa4f2a ("r8169: fix LED-related deadlock on module removal")
Reported-by: Venkat Rao Bagalkote <venkat88@linux.vnet.ibm.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-By: Venkat Rao Bagalkote <venkat88@linux.vnet.ibm.com>
Link: https://lore.kernel.org/r/d080038c-eb6b-45ac-9237-b8c1cdd7870f@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The commit 40b5d2f1 ("net: dsa: mt7530: Add support for EEE features")
brought EEE support but did not enable EEE on MT7531 switch MACs. EEE is
enabled on MT7531 switch MACs by pulling the LAN2LED0 pin low on the board
(bootstrapping), unsetting the EEE_DIS bit on the trap register, or setting
the internal EEE switch bit on the CORE_PLL_GROUP4 register. Thanks to
SkyLake Huang (黃啟澤) from MediaTek for providing information on the
internal EEE switch bit.

There are existing boards that were not designed to pull the pin low.
Because of that, the EEE status currently depends on the board design.

The EEE_DIS bit on the trap pertains to the LAN2LED0 pin which is usually
used to control an LED. Once the bit is unset, the pin will be low. That
will make the active low LED turn on. The pin is controlled by the switch
PHY. It seems that the PHY controls the pin in the way that it inverts the
pin state. That means depending on the wiring of the LED connected to
LAN2LED0 on the board, the LED may be on without an active link.

To not cause this unwanted behaviour whilst enabling EEE on all boards, set
the internal EEE switch bit on the CORE_PLL_GROUP4 register.

My testing on MT7531 shows a certain amount of traffic loss when EEE is
enabled. That said, I haven't come across a board that enables EEE. So
enable EEE on the switch MACs but disable EEE advertisement on the switch
PHYs. This way, we don't change the behaviour of the majority of the boards
that have this switch. The mediatek-ge PHY driver already disables EEE
advertisement on the switch PHYs but my testing shows that it is somehow
enabled afterwards. Disabling EEE advertisement before the PHY driver
initialises keeps it off.

With this change, EEE can now be enabled using ethtool.

Fixes: 40b5d2f1 ("net: dsa: mt7530: Add support for EEE features")
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20240408-for-net-mt7530-fix-eee-for-mt7531-mt7988-v3-1-84fdef1f008b@arinc9.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Binding devm_led_classdev_register() to the netdev is problematic
because on module removal we get a RTNL-related deadlock. Fix this
by avoiding the device-managed LED functions.

Note: We can safely call led_classdev_unregister() for a LED even
if registering it failed, because led_classdev_unregister() detects
this and is a no-op in this case.

Fixes: 18764b88 ("r8169: add support for LED's on RTL8168/RTL8101")
Cc: stable@vger.kernel.org
Reported-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the driver notices fw_status == 0xff it tries to perform a PCI
reset on itself via pci_reset_function() in the context of the driver's
health thread. However, pdsc_reset_prepare calls
pdsc_stop_health_thread(), which attempts to stop/flush the health
thread. This results in a deadlock because the stop/flush will never
complete since the driver called pci_reset_function() from the health
thread context. Fix by changing the pdsc_check_pci_health_function()
to queue a newly introduced pdsc_pci_reset_thread() on the pdsc's
work queue.

Unloading the driver in the fw_down/dead state uncovered another issue,
which can be seen in the following trace:

WARNING: CPU: 51 PID: 6914 at kernel/workqueue.c:1450 __queue_work+0x358/0x440
[...]
RIP: 0010:__queue_work+0x358/0x440
[...]
Call Trace:
 <TASK>
 ? __warn+0x85/0x140
 ? __queue_work+0x358/0x440
 ? report_bug+0xfc/0x1e0
 ? handle_bug+0x3f/0x70
 ? exc_invalid_op+0x17/0x70
 ? asm_exc_invalid_op+0x1a/0x20
 ? __queue_work+0x358/0x440
 queue_work_on+0x28/0x30
 pdsc_devcmd_locked+0x96/0xe0 [pds_core]
 pdsc_devcmd_reset+0x71/0xb0 [pds_core]
 pdsc_teardown+0x51/0xe0 [pds_core]
 pdsc_remove+0x106/0x200 [pds_core]
 pci_device_remove+0x37/0xc0
 device_release_driver_internal+0xae/0x140
 driver_detach+0x48/0x90
 bus_remove_driver+0x6d/0xf0
 pci_unregister_driver+0x2e/0xa0
 pdsc_cleanup_module+0x10/0x780 [pds_core]
 __x64_sys_delete_module+0x142/0x2b0
 ? syscall_trace_enter.isra.18+0x126/0x1a0
 do_syscall_64+0x3b/0x90
 entry_SYSCALL_64_after_hwframe+0x72/0xdc
RIP: 0033:0x7fbd9d03a14b
[...]

Fix this by preventing the devcmd reset if the FW is not running.

Fixes: d9407ff1 ("pds_core: Prevent health thread from running during reset/remove")
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Brett Creeley <brett.creeley@amd.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Although ipv6_get_ifaddr walks inet6_addr_lst under the RCU lock, it
still means hlist_for_each_entry_rcu can return an item that got removed
from the list. The memory itself of such item is not freed thanks to RCU
but nothing guarantees the actual content of the memory is sane.

In particular, the reference count can be zero. This can happen if
ipv6_del_addr is called in parallel. ipv6_del_addr removes the entry
from inet6_addr_lst (hlist_del_init_rcu(&ifp->addr_lst)) and drops all
references (__in6_ifa_put(ifp) + in6_ifa_put(ifp)). With bad enough
timing, this can happen:

1. In ipv6_get_ifaddr, hlist_for_each_entry_rcu returns an entry.

2. Then, the whole ipv6_del_addr is executed for the given entry. The
   reference count drops to zero and kfree_rcu is scheduled.

3. ipv6_get_ifaddr continues and tries to increments the reference count
   (in6_ifa_hold).

4. The rcu is unlocked and the entry is freed.

5. The freed entry is returned.

Prevent increasing of the reference count in such case. The name
in6_ifa_hold_safe is chosen to mimic the existing fib6_info_hold_safe.

[   41.506330] refcount_t: addition on 0; use-after-free.
[   41.506760] WARNING: CPU: 0 PID: 595 at lib/refcount.c:25 refcount_warn_saturate+0xa5/0x130
[   41.507413] Modules linked in: veth bridge stp llc
[   41.507821] CPU: 0 PID: 595 Comm: python3 Not tainted 6.9.0-rc2.main-00208-g49563be8 #14
[   41.508479] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996)
[   41.509163] RIP: 0010:refcount_warn_saturate+0xa5/0x130
[   41.509586] Code: ad ff 90 0f 0b 90 90 c3 cc cc cc cc 80 3d c0 30 ad 01 00 75 a0 c6 05 b7 30 ad 01 01 90 48 c7 c7 38 cc 7a 8c e8 cc 18 ad ff 90 <0f> 0b 90 90 c3 cc cc cc cc 80 3d 98 30 ad 01 00 0f 85 75 ff ff ff
[   41.510956] RSP: 0018:ffffbda3c026baf0 EFLAGS: 00010282
[   41.511368] RAX: 0000000000000000 RBX: ffff9e9c46914800 RCX: 0000000000000000
[   41.511910] RDX: ffff9e9c7ec29c00 RSI: ffff9e9c7ec1c900 RDI: ffff9e9c7ec1c900
[   41.512445] RBP: ffff9e9c43660c9c R08: 0000000000009ffb R09: 00000000ffffdfff
[   41.512998] R10: 00000000ffffdfff R11: ffffffff8ca58a40 R12: ffff9e9c4339a000
[   41.513534] R13: 0000000000000001 R14: ffff9e9c438a0000 R15: ffffbda3c026bb48
[   41.514086] FS:  00007fbc4cda1740(0000) GS:ffff9e9c7ec00000(0000) knlGS:0000000000000000
[   41.514726] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   41.515176] CR2: 000056233b337d88 CR3: 000000000376e006 CR4: 0000000000370ef0
[   41.515713] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   41.516252] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[   41.516799] Call Trace:
[   41.517037]  <TASK>
[   41.517249]  ? __warn+0x7b/0x120
[   41.517535]  ? refcount_warn_saturate+0xa5/0x130
[   41.517923]  ? report_bug+0x164/0x190
[   41.518240]  ? handle_bug+0x3d/0x70
[   41.518541]  ? exc_invalid_op+0x17/0x70
[   41.520972]  ? asm_exc_invalid_op+0x1a/0x20
[   41.521325]  ? refcount_warn_saturate+0xa5/0x130
[   41.521708]  ipv6_get_ifaddr+0xda/0xe0
[   41.522035]  inet6_rtm_getaddr+0x342/0x3f0
[   41.522376]  ? __pfx_inet6_rtm_getaddr+0x10/0x10
[   41.522758]  rtnetlink_rcv_msg+0x334/0x3d0
[   41.523102]  ? netlink_unicast+0x30f/0x390
[   41.523445]  ? __pfx_rtnetlink_rcv_msg+0x10/0x10
[   41.523832]  netlink_rcv_skb+0x53/0x100
[   41.524157]  netlink_unicast+0x23b/0x390
[   41.524484]  netlink_sendmsg+0x1f2/0x440
[   41.524826]  __sys_sendto+0x1d8/0x1f0
[   41.525145]  __x64_sys_sendto+0x1f/0x30
[   41.525467]  do_syscall_64+0xa5/0x1b0
[   41.525794]  entry_SYSCALL_64_after_hwframe+0x72/0x7a
[   41.526213] RIP: 0033:0x7fbc4cfcea9a
[   41.526528] Code: d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 41 89 ca 64 8b 04 25 18 00 00 00 85 c0 75 15 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 7e c3 0f 1f 44 00 00 41 54 48 83 ec 30 44 89
[   41.527942] RSP: 002b:00007ffcf54012a8 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
[   41.528593] RAX: ffffffffffffffda RBX: 00007ffcf5401368 RCX: 00007fbc4cfcea9a
[   41.529173] RDX: 000000000000002c RSI: 00007fbc4b9d9bd0 RDI: 0000000000000005
[   41.529786] RBP: 00007fbc4bafb040 R08: 00007ffcf54013e0 R09: 000000000000000c
[   41.530375] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
[   41.530977] R13: ffffffffc4653600 R14: 0000000000000001 R15: 00007fbc4ca85d1b
[   41.531573]  </TASK>

Fixes: 5c578aed ("IPv6: convert addrconf hash list to RCU")
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Link: https://lore.kernel.org/r/8ab821e36073a4a406c50ec83c9e8dc586c539e4.1712585809.git.jbenc@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Eric Dumazet says:

====================
net: start to replace copy_from_sockptr()

We got several syzbot reports about unsafe copy_from_sockptr()
calls. After fixing some of them, it appears that we could
use a new helper to factorize all the checks in one place.

This series targets net tree, we can later start converting
many call sites in net-next.
====================

Link: https://lore.kernel.org/r/20240408082845.3957374-1-edumazet@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

syzbot reported unsafe calls to copy_from_sockptr() [1]

Use copy_safe_from_sockptr() instead.

[1]

BUG: KASAN: slab-out-of-bounds in copy_from_sockptr_offset include/linux/sockptr.h:49 [inline]
 BUG: KASAN: slab-out-of-bounds in copy_from_sockptr include/linux/sockptr.h:55 [inline]
 BUG: KASAN: slab-out-of-bounds in nfc_llcp_setsockopt+0x6c2/0x850 net/nfc/llcp_sock.c:255
Read of size 4 at addr ffff88801caa1ec3 by task syz-executor459/5078

CPU: 0 PID: 5078 Comm: syz-executor459 Not tainted 6.8.0-syzkaller-08951-gfe46a7dd #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/27/2024
Call Trace:
 <TASK>
  __dump_stack lib/dump_stack.c:88 [inline]
  dump_stack_lvl+0x241/0x360 lib/dump_stack.c:114
  print_address_description mm/kasan/report.c:377 [inline]
  print_report+0x169/0x550 mm/kasan/report.c:488
  kasan_report+0x143/0x180 mm/kasan/report.c:601
  copy_from_sockptr_offset include/linux/sockptr.h:49 [inline]
  copy_from_sockptr include/linux/sockptr.h:55 [inline]
  nfc_llcp_setsockopt+0x6c2/0x850 net/nfc/llcp_sock.c:255
  do_sock_setsockopt+0x3b1/0x720 net/socket.c:2311
  __sys_setsockopt+0x1ae/0x250 net/socket.c:2334
  __do_sys_setsockopt net/socket.c:2343 [inline]
  __se_sys_setsockopt net/socket.c:2340 [inline]
  __x64_sys_setsockopt+0xb5/0xd0 net/socket.c:2340
 do_syscall_64+0xfd/0x240
 entry_SYSCALL_64_after_hwframe+0x6d/0x75
RIP: 0033:0x7f7fac07fd89
Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 91 18 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007fff660eb788 EFLAGS: 00000246 ORIG_RAX: 0000000000000036
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00007f7fac07fd89
RDX: 0000000000000000 RSI: 0000000000000118 RDI: 0000000000000004
RBP: 0000000000000000 R08: 0000000000000002 R09: 0000000000000000
R10: 0000000020000a80 R11: 0000000000000246 R12: 0000000000000000
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240408082845.3957374-4-edumazet@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

syzbot reports one unsafe call to copy_from_sockptr() [1]

Use copy_safe_from_sockptr() instead.

[1]

 BUG: KASAN: slab-out-of-bounds in copy_from_sockptr_offset include/linux/sockptr.h:49 [inline]
 BUG: KASAN: slab-out-of-bounds in copy_from_sockptr include/linux/sockptr.h:55 [inline]
 BUG: KASAN: slab-out-of-bounds in data_sock_setsockopt+0x46c/0x4cc drivers/isdn/mISDN/socket.c:417
Read of size 4 at addr ffff0000c6d54083 by task syz-executor406/6167

CPU: 1 PID: 6167 Comm: syz-executor406 Not tainted 6.8.0-rc7-syzkaller-g707081b61156 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/27/2024
Call trace:
  dump_backtrace+0x1b8/0x1e4 arch/arm64/kernel/stacktrace.c:291
  show_stack+0x2c/0x3c arch/arm64/kernel/stacktrace.c:298
  __dump_stack lib/dump_stack.c:88 [inline]
  dump_stack_lvl+0xd0/0x124 lib/dump_stack.c:106
  print_address_description mm/kasan/report.c:377 [inline]
  print_report+0x178/0x518 mm/kasan/report.c:488
  kasan_report+0xd8/0x138 mm/kasan/report.c:601
  __asan_report_load_n_noabort+0x1c/0x28 mm/kasan/report_generic.c:391
  copy_from_sockptr_offset include/linux/sockptr.h:49 [inline]
  copy_from_sockptr include/linux/sockptr.h:55 [inline]
  data_sock_setsockopt+0x46c/0x4cc drivers/isdn/mISDN/socket.c:417
  do_sock_setsockopt+0x2a0/0x4e0 net/socket.c:2311
  __sys_setsockopt+0x128/0x1a8 net/socket.c:2334
  __do_sys_setsockopt net/socket.c:2343 [inline]
  __se_sys_setsockopt net/socket.c:2340 [inline]
  __arm64_sys_setsockopt+0xb8/0xd4 net/socket.c:2340
  __invoke_syscall arch/arm64/kernel/syscall.c:34 [inline]
  invoke_syscall+0x98/0x2b8 arch/arm64/kernel/syscall.c:48
  el0_svc_common+0x130/0x23c arch/arm64/kernel/syscall.c:133
  do_el0_svc+0x48/0x58 arch/arm64/kernel/syscall.c:152
  el0_svc+0x54/0x168 arch/arm64/kernel/entry-common.c:712
  el0t_64_sync_handler+0x84/0xfc arch/arm64/kernel/entry-common.c:730
  el0t_64_sync+0x190/0x194 arch/arm64/kernel/entry.S:598

Fixes: 1b2b03f8 ("Add mISDN core files")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Link: https://lore.kernel.org/r/20240408082845.3957374-3-edumazet@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

copy_from_sockptr() helper is unsafe, unless callers
did the prior check against user provided optlen.

Too many callers get this wrong, lets add a helper to
fix them and avoid future copy/paste bugs.

Instead of :

   if (optlen < sizeof(opt)) {
       err = -EINVAL;
       break;
   }
   if (copy_from_sockptr(&opt, optval, sizeof(opt)) {
       err = -EFAULT;
       break;
   }

Use :

   err = copy_safe_from_sockptr(&opt, sizeof(opt),
                                optval, optlen);
   if (err)
       break;
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240408082845.3957374-2-edumazet@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The log_martians variable is only used in an #ifdef, causing a 'make W=1'
warning with gcc:

net/ipv4/route.c: In function 'ip_rt_send_redirect':
net/ipv4/route.c:880:13: error: variable 'log_martians' set but not used [-Werror=unused-but-set-variable]

Change the #ifdef to an equivalent IS_ENABLED() to let the compiler
see where the variable is used.

Fixes: 30038fc6 ("net: ip_rt_send_redirect() optimization")
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240408074219.3030256-2-arnd@kernel.orgSigned-off-by: Paolo Abeni <pabeni@redhat.com>

When CONFIG_IPV6_SUBTREES is disabled, the only user is hidden, causing
a 'make W=1' warning:

net/ipv6/ip6_fib.c: In function 'fib6_add':
net/ipv6/ip6_fib.c:1388:32: error: variable 'pn' set but not used [-Werror=unused-but-set-variable]

Add another #ifdef around the variable declaration, matching the other
uses in this file.

Fixes: 66729e18 ("[IPV6] ROUTE: Make sure we have fn->leaf when adding a node on subtree.")
Link: https://lore.kernel.org/netdev/20240322131746.904943-1-arnd@kernel.org/Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240408074219.3030256-1-arnd@kernel.orgSigned-off-by: Paolo Abeni <pabeni@redhat.com>

NIX SQ mode and link backpressure configuration is required for
all platforms. But in current driver this code is wrongly placed
under specific platform check. This patch fixes the issue by
moving the code out of platform check.

Fixes: 5d9b976d ("octeontx2-af: Support fixed transmit scheduler topology")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Link: https://lore.kernel.org/r/20240408063643.26288-1-gakula@marvell.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

syzkaller started to report deadlock of unix_gc_lock after commit
4090fa37 ("af_unix: Replace garbage collection algorithm."), but
it just uncovers the bug that has been there since commit 314001f0
("af_unix: Add OOB support").

The repro basically does the following.

  from socket import *
  from array import array

  c1, c2 = socketpair(AF_UNIX, SOCK_STREAM)
  c1.sendmsg([b'a'], [(SOL_SOCKET, SCM_RIGHTS, array("i", [c2.fileno()]))], MSG_OOB)
  c2.recv(1)  # blocked as no normal data in recv queue

  c2.close()  # done async and unblock recv()
  c1.close()  # done async and trigger GC

A socket sends its file descriptor to itself as OOB data and tries to
receive normal data, but finally recv() fails due to async close().

The problem here is wrong handling of OOB skb in manage_oob().  When
recvmsg() is called without MSG_OOB, manage_oob() is called to check
if the peeked skb is OOB skb.  In such a case, manage_oob() pops it
out of the receive queue but does not clear unix_sock(sk)->oob_skb.
This is wrong in terms of uAPI.

Let's say we send "hello" with MSG_OOB, and "world" without MSG_OOB.
The 'o' is handled as OOB data.  When recv() is called twice without
MSG_OOB, the OOB data should be lost.

  >>> from socket import *
  >>> c1, c2 = socketpair(AF_UNIX, SOCK_STREAM, 0)
  >>> c1.send(b'hello', MSG_OOB)  # 'o' is OOB data
  5
  >>> c1.send(b'world')
  5
  >>> c2.recv(5)  # OOB data is not received
  b'hell'
  >>> c2.recv(5)  # OOB date is skipped
  b'world'
  >>> c2.recv(5, MSG_OOB)  # This should return an error
  b'o'

In the same situation, TCP actually returns -EINVAL for the last
recv().

Also, if we do not clear unix_sk(sk)->oob_skb, unix_poll() always set
EPOLLPRI even though the data has passed through by previous recv().

To avoid these issues, we must clear unix_sk(sk)->oob_skb when dequeuing
it from recv queue.

The reason why the old GC did not trigger the deadlock is because the
old GC relied on the receive queue to detect the loop.

When it is triggered, the socket with OOB data is marked as GC candidate
because file refcount == inflight count (1).  However, after traversing
all inflight sockets, the socket still has a positive inflight count (1),
thus the socket is excluded from candidates.  Then, the old GC lose the
chance to garbage-collect the socket.

With the old GC, the repro continues to create true garbage that will
never be freed nor detected by kmemleak as it's linked to the global
inflight list.  That's why we couldn't even notice the issue.

Fixes: 314001f0 ("af_unix: Add OOB support")
Reported-by: syzbot+7f7f201cc2668a8fd169@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=7f7f201cc2668a8fd169Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240405221057.2406-1-kuniyu@amazon.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The ks8851_irq() thread may call ks8851_rx_pkts() in case there are
any packets in the MAC FIFO, which calls netif_rx(). This netif_rx()
implementation is guarded by local_bh_disable() and local_bh_enable().
The local_bh_enable() may call do_softirq() to run softirqs in case
any are pending. One of the softirqs is net_rx_action, which ultimately
reaches the driver .start_xmit callback. If that happens, the system
hangs. The entire call chain is below:

ks8851_start_xmit_par from netdev_start_xmit
netdev_start_xmit from dev_hard_start_xmit
dev_hard_start_xmit from sch_direct_xmit
sch_direct_xmit from __dev_queue_xmit
__dev_queue_xmit from __neigh_update
__neigh_update from neigh_update
neigh_update from arp_process.constprop.0
arp_process.constprop.0 from __netif_receive_skb_one_core
__netif_receive_skb_one_core from process_backlog
process_backlog from __napi_poll.constprop.0
__napi_poll.constprop.0 from net_rx_action
net_rx_action from __do_softirq
__do_softirq from call_with_stack
call_with_stack from do_softirq
do_softirq from __local_bh_enable_ip
__local_bh_enable_ip from netif_rx
netif_rx from ks8851_irq
ks8851_irq from irq_thread_fn
irq_thread_fn from irq_thread
irq_thread from kthread
kthread from ret_from_fork

The hang happens because ks8851_irq() first locks a spinlock in
ks8851_par.c ks8851_lock_par() spin_lock_irqsave(&ksp->lock, ...)
and with that spinlock locked, calls netif_rx(). Once the execution
reaches ks8851_start_xmit_par(), it calls ks8851_lock_par() again
which attempts to claim the already locked spinlock again, and the
hang happens.

Move the do_softirq() call outside of the spinlock protected section
of ks8851_irq() by disabling BHs around the entire spinlock protected
section of ks8851_irq() handler. Place local_bh_enable() outside of
the spinlock protected section, so that it can trigger do_softirq()
without the ks8851_par.c ks8851_lock_par() spinlock being held, and
safely call ks8851_start_xmit_par() without attempting to lock the
already locked spinlock.

Since ks8851_irq() is protected by local_bh_disable()/local_bh_enable()
now, replace netif_rx() with __netif_rx() which is not duplicating the
local_bh_disable()/local_bh_enable() calls.

Fixes: 797047f8 ("net: ks8851: Implement Parallel bus operations")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20240405203204.82062-2-marex@denx.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Both ks8851_rx_skb_par() and ks8851_rx_skb_spi() call netif_rx(skb),
inline the netif_rx(skb) call directly into ks8851_common.c and drop
the .rx_skb callback and ks8851_rx_skb() wrapper. This removes one
indirect call from the driver, no functional change otherwise.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20240405203204.82062-1-marex@denx.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Minda Chen says:

====================
Add missing mmc statistics in DW GMAC

Add miss MMC statistic in DW GMAC

base on 6.9-rc1

changed
v2:
   patch2 : remove mmc_rx_control_g due to it is gotten in
ethtool_ops::get_eth_ctrl_stats.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The missing statistics including Rx_Receive_Error_Packets and
Tx_OSize_Packets_Good.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

XGMAC MMC has already added LPI statistics. GMAC MMC lack of these
statistics. Add register definition and reading the LPI statistics
from registers.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Bug fixes

The first 2 patches fix 2 potential issues in the aux bus initialization
and error recovery paths.  The 3rd patch fixes a potential PTP TX
timestamp issue during error recovery.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

It is possible that during error recovery and firmware reset,
there is a pending TX PTP packet waiting for the timestamp.
We need to reset this condition so that after recovery, the
tx_avail count for PTP is reset back to the initial value.
Otherwise, we may not accept any PTP TX timestamps after
recovery.

Fixes: 118612d5 ("bnxt_en: Add PTP clock APIs, ioctls, and ethtool methods")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since runtime MSIXs vector allocation/free has been removed,
the L2 driver needs to repopulate the MSIX entries for the
ulp client as the irq table may change during the recovery
process.

Fixes: 30343221 ("bnxt_en: Remove runtime interrupt vector allocation")
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If ulp = kzalloc() fails, the allocated edev will leak because it is
not properly assigned and the cleanup path will not be able to free it.
Fix it by assigning it properly immediately after allocation.

Fixes: 30343221 ("bnxt_en: Remove runtime interrupt vector allocation")
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since [1], dma_alloc_coherent() does not accept requests for GFP_COMP
anymore, even on archs that may be able to fulfill this. Functionality that
relied on the receive buffer being a compound page broke at that point:
The SMC-D protocol, that utilizes the ism device driver, passes receive
buffers to the splice processor in a struct splice_pipe_desc with a
single entry list of struct pages. As the buffer is no longer a compound
page, the splice processor now rejects requests to handle more than a
page worth of data.

Replace dma_alloc_coherent() and allocate a buffer with folio_alloc and
create a DMA map for it with dma_map_page(). Since only receive buffers
on ISM devices use DMA, qualify the mapping as FROM_DEVICE.
Since ISM devices are available on arch s390, only and on that arch all
DMA is coherent, there is no need to introduce and export some kind of
dma_sync_to_cpu() method to be called by the SMC-D protocol layer.

Analogously, replace dma_free_coherent by a two step dma_unmap_page,
then folio_put to free the receive buffer.

[1] https://lore.kernel.org/all/20221113163535.884299-1-hch@lst.de/

Fixes: c08004ee ("s390/ism: don't pass bogus GFP_ flags to dma_alloc_coherent")
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>