[ Upstream commit 70e4da7a ]

Commit 172b2386 ("KVM: x86: fix missed hardware breakpoints",
2016-02-10) worked around a case where the debug registers are not loaded
correctly on preemption and on the first entry to KVM_RUN.

However, Xiao Guangrong pointed out that the root cause must be that
KVM_DEBUGREG_BP_ENABLED is not being set correctly.  This can indeed
happen due to the lazy debug exit mechanism, which does not call
kvm_update_dr7.  Fix it by replacing the existing loop (more or less
equivalent to kvm_update_dr0123) with calls to all the kvm_update_dr*
functions.

Cc: stable@vger.kernel.org   # 4.1+
Fixes: 172b2386Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 4ee34ea3 ]

The id buffer in ata_device is a DMA target, but it isn't explicitly
cacheline aligned. Due to this, adjacent fields can be overwritten with
stale data from memory on non coherent architectures. As a result, the
kernel is sometimes unable to communicate with an ATA device.

Fix this by ensuring that the id buffer is cacheline aligned.

This issue is similar to that fixed by Commit 84bda12a
("libata: align ap->sector_buf").
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: <stable@vger.kernel.org> # 2.6.18
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 358875fd ]

The AMD Family 15h Models 30h-3Fh (Kaveri) BIOS and Kernel Developer's
Guide omitted part of the BIOS IOMMU L2 register setup specification.
Without this setup the IOMMU L2 does not fully respect write permissions
when handling an ATS translation request.

The IOMMU L2 will set PTE dirty bit when handling an ATS translation with
write permission request, even when PTE RW bit is clear. This may occur by
direct translation (which would cause a PPR) or by prefetch request from
the ATC.

This is observed in practice when the IOMMU L2 modifies a PTE which maps a
pagecache page. The ext4 filesystem driver BUGs when asked to writeback
these (non-modified) pages.

Enable ATS write permission check in the Kaveri IOMMU L2 if BIOS has not.
Signed-off-by: Jay Cornwall <jay@jcornwall.me>
Cc: <stable@vger.kernel.org> # v3.19+
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 38e45d02 ]

The setup code for the performance counters in the AMD IOMMU driver
tests whether the counters can be written. It tests to setup a counter
for device 00:00.0, which fails on systems where this particular device
is not covered by the IOMMU.

Fix this by not relying on device 00:00.0 but only on the IOMMU being
present.

Cc: stable@vger.kernel.org
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit f883982d ]

HP EliteBook 755 G2 with ALC3228 (ALC280) codec [103c:221c] requires
the known fixup (ALC269_FIXUP_HEADSET_MIC) for making the headset mic
working.  Also, it suffers from the loopback noise problem, so we
should disable aamix path as well.
Reported-by: Derick Eddington <derick.eddington@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 2ae95577 ]

On one of the machines we enable, we found that the actual speaker volume
did not always correspond to the volume set in alsamixer. This patch
fixes that problem.

This patch was orginally written by Kailang @ Realtek, I've rebased it
to fit sound git master.

Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/bugs/1549660Co-Authored-By: Kailang <kailang@realtek.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit cfc5a845 ]

Dell create new platform with ALC298 codec.
This patch will enable headset mode for ALC225/ALC3253 platform.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit be629c62 ]

When a directory is deleted, we don't take too much care about killing off
all the dirents that belong to it — on the basis that on remount, the scan
will conclude that the directory is dead anyway.

This doesn't work though, when the deleted directory contained a child
directory which was moved *out*. In the early stages of the fs build
we can then end up with an apparent hard link, with the child directory
appearing both in its true location, and as a child of the original
directory which are this stage of the mount process we don't *yet* know
is defunct.

To resolve this, take out the early special-casing of the "directories
shall not have hard links" rule in jffs2_build_inode_pass1(), and let the
normal nlink processing happen for directories as well as other inodes.

Then later in the build process we can set ic->pino_nlink to the parent
inode#, as is required for directories during normal operaton, instead
of the nlink. And complain only *then* about hard links which are still
in evidence even after killing off all the unreachable paths.
Reported-by: Liu Song <liu.song11@zte.com.cn>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 49e91e70 ]

With this fix, all code paths should now be obtaining the page lock before
f->sem.
Reported-by: Szabó Tamás <sztomi89@gmail.com>
Tested-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 157078f6 ]

This reverts commit 5ffd3412
("jffs2: Fix lock acquisition order bug in jffs2_write_begin").

The commit modified jffs2_write_begin() to remove a deadlock with
jffs2_garbage_collect_live(), but this introduced new deadlocks found
by multiple users. page_lock() actually has to be called before
mutex_lock(&c->alloc_sem) or mutex_lock(&f->sem) because
jffs2_write_end() and jffs2_readpage() are called with the page locked,
and they acquire c->alloc_sem and f->sem, resp.

In other words, the lock order in jffs2_write_begin() was correct, and
it is the jffs2_garbage_collect_live() path that has to be changed.

Revert the commit to get rid of the new deadlocks, and to clear the way
for a better fix of the original deadlock.
Reported-by: Deng Chao <deng.chao1@zte.com.cn>
Reported-by: Ming Liu <liu.ming50@gmail.com>
Reported-by: wangzaiwei <wangzaiwei@top-vision.cn>
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 17e4bce0 ]

Ubsan reports the following warning due to a typo in
update_accessed_dirty_bits template, the patch fixes
the typo:

[  168.791851] ================================================================================
[  168.791862] UBSAN: Undefined behaviour in arch/x86/kvm/paging_tmpl.h:252:15
[  168.791866] index 4 is out of range for type 'u64 [4]'
[  168.791871] CPU: 0 PID: 2950 Comm: qemu-system-x86 Tainted: G           O L  4.5.0-rc5-next-20160222 #7
[  168.791873] Hardware name: LENOVO 23205NG/23205NG, BIOS G2ET95WW (2.55 ) 07/09/2013
[  168.791876]  0000000000000000 ffff8801cfcaf208 ffffffff81c9f780 0000000041b58ab3
[  168.791882]  ffffffff82eb2cc1 ffffffff81c9f6b4 ffff8801cfcaf230 ffff8801cfcaf1e0
[  168.791886]  0000000000000004 0000000000000001 0000000000000000 ffffffffa1981600
[  168.791891] Call Trace:
[  168.791899]  [<ffffffff81c9f780>] dump_stack+0xcc/0x12c
[  168.791904]  [<ffffffff81c9f6b4>] ? _atomic_dec_and_lock+0xc4/0xc4
[  168.791910]  [<ffffffff81da9e81>] ubsan_epilogue+0xd/0x8a
[  168.791914]  [<ffffffff81daafa2>] __ubsan_handle_out_of_bounds+0x15c/0x1a3
[  168.791918]  [<ffffffff81daae46>] ? __ubsan_handle_shift_out_of_bounds+0x2bd/0x2bd
[  168.791922]  [<ffffffff811287ef>] ? get_user_pages_fast+0x2bf/0x360
[  168.791954]  [<ffffffffa1794050>] ? kvm_largepages_enabled+0x30/0x30 [kvm]
[  168.791958]  [<ffffffff81128530>] ? __get_user_pages_fast+0x360/0x360
[  168.791987]  [<ffffffffa181b818>] paging64_walk_addr_generic+0x1b28/0x2600 [kvm]
[  168.792014]  [<ffffffffa1819cf0>] ? init_kvm_mmu+0x1100/0x1100 [kvm]
[  168.792019]  [<ffffffff8129e350>] ? debug_check_no_locks_freed+0x350/0x350
[  168.792044]  [<ffffffffa1819cf0>] ? init_kvm_mmu+0x1100/0x1100 [kvm]
[  168.792076]  [<ffffffffa181c36d>] paging64_gva_to_gpa+0x7d/0x110 [kvm]
[  168.792121]  [<ffffffffa181c2f0>] ? paging64_walk_addr_generic+0x2600/0x2600 [kvm]
[  168.792130]  [<ffffffff812e848b>] ? debug_lockdep_rcu_enabled+0x7b/0x90
[  168.792178]  [<ffffffffa17d9a4a>] emulator_read_write_onepage+0x27a/0x1150 [kvm]
[  168.792208]  [<ffffffffa1794d44>] ? __kvm_read_guest_page+0x54/0x70 [kvm]
[  168.792234]  [<ffffffffa17d97d0>] ? kvm_task_switch+0x160/0x160 [kvm]
[  168.792238]  [<ffffffff812e848b>] ? debug_lockdep_rcu_enabled+0x7b/0x90
[  168.792263]  [<ffffffffa17daa07>] emulator_read_write+0xe7/0x6d0 [kvm]
[  168.792290]  [<ffffffffa183b620>] ? em_cr_write+0x230/0x230 [kvm]
[  168.792314]  [<ffffffffa17db005>] emulator_write_emulated+0x15/0x20 [kvm]
[  168.792340]  [<ffffffffa18465f8>] segmented_write+0xf8/0x130 [kvm]
[  168.792367]  [<ffffffffa1846500>] ? em_lgdt+0x20/0x20 [kvm]
[  168.792374]  [<ffffffffa14db512>] ? vmx_read_guest_seg_ar+0x42/0x1e0 [kvm_intel]
[  168.792400]  [<ffffffffa1846d82>] writeback+0x3f2/0x700 [kvm]
[  168.792424]  [<ffffffffa1846990>] ? em_sidt+0xa0/0xa0 [kvm]
[  168.792449]  [<ffffffffa185554d>] ? x86_decode_insn+0x1b3d/0x4f70 [kvm]
[  168.792474]  [<ffffffffa1859032>] x86_emulate_insn+0x572/0x3010 [kvm]
[  168.792499]  [<ffffffffa17e71dd>] x86_emulate_instruction+0x3bd/0x2110 [kvm]
[  168.792524]  [<ffffffffa17e6e20>] ? reexecute_instruction.part.110+0x2e0/0x2e0 [kvm]
[  168.792532]  [<ffffffffa14e9a81>] handle_ept_misconfig+0x61/0x460 [kvm_intel]
[  168.792539]  [<ffffffffa14e9a20>] ? handle_pause+0x450/0x450 [kvm_intel]
[  168.792546]  [<ffffffffa15130ea>] vmx_handle_exit+0xd6a/0x1ad0 [kvm_intel]
[  168.792572]  [<ffffffffa17f6a6c>] ? kvm_arch_vcpu_ioctl_run+0xbdc/0x6090 [kvm]
[  168.792597]  [<ffffffffa17f6bcd>] kvm_arch_vcpu_ioctl_run+0xd3d/0x6090 [kvm]
[  168.792621]  [<ffffffffa17f6a6c>] ? kvm_arch_vcpu_ioctl_run+0xbdc/0x6090 [kvm]
[  168.792627]  [<ffffffff8293b530>] ? __ww_mutex_lock_interruptible+0x1630/0x1630
[  168.792651]  [<ffffffffa17f5e90>] ? kvm_arch_vcpu_runnable+0x4f0/0x4f0 [kvm]
[  168.792656]  [<ffffffff811eeb30>] ? preempt_notifier_unregister+0x190/0x190
[  168.792681]  [<ffffffffa17e0447>] ? kvm_arch_vcpu_load+0x127/0x650 [kvm]
[  168.792704]  [<ffffffffa178e9a3>] kvm_vcpu_ioctl+0x553/0xda0 [kvm]
[  168.792727]  [<ffffffffa178e450>] ? vcpu_put+0x40/0x40 [kvm]
[  168.792732]  [<ffffffff8129e350>] ? debug_check_no_locks_freed+0x350/0x350
[  168.792735]  [<ffffffff82946087>] ? _raw_spin_unlock+0x27/0x40
[  168.792740]  [<ffffffff8163a943>] ? handle_mm_fault+0x1673/0x2e40
[  168.792744]  [<ffffffff8129daa8>] ? trace_hardirqs_on_caller+0x478/0x6c0
[  168.792747]  [<ffffffff8129dcfd>] ? trace_hardirqs_on+0xd/0x10
[  168.792751]  [<ffffffff812e848b>] ? debug_lockdep_rcu_enabled+0x7b/0x90
[  168.792756]  [<ffffffff81725a80>] do_vfs_ioctl+0x1b0/0x12b0
[  168.792759]  [<ffffffff817258d0>] ? ioctl_preallocate+0x210/0x210
[  168.792763]  [<ffffffff8174aef3>] ? __fget+0x273/0x4a0
[  168.792766]  [<ffffffff8174acd0>] ? __fget+0x50/0x4a0
[  168.792770]  [<ffffffff8174b1f6>] ? __fget_light+0x96/0x2b0
[  168.792773]  [<ffffffff81726bf9>] SyS_ioctl+0x79/0x90
[  168.792777]  [<ffffffff82946880>] entry_SYSCALL_64_fastpath+0x23/0xc1
[  168.792780] ================================================================================
Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com>
Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 7cb32ae0 ]

commit 3b43b71f upstream.

After login to the desktop on Dell Inspiron 3162,
there's a very loud background noise comes from the builtin speaker.
The noise does not go away even if the speaker is muted.

The noise disappears after using the aamix fixup.

Codec: Realtek ALC3234
Address: 0
AFG Function Id: 0x1 (unsol 1)
    Vendor Id: 0x10ec0255
    Subsystem Id: 0x10280725
    Revision Id: 0x100002
    No Modem Function Group found

BugLink: http://bugs.launchpad.net/bugs/1549620Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 3694cb29 ]

The Lenovo ThinkCenter AIO uses Line2 (NID 0x1b) to implement the
micmute hotkey, here we register an input device and use Line2 unsol
event to collect the hotkey pressing or releasing.

In the meanwhile, the micmute led is controlled by GPIO2, so we
use an existing function alc_fixup_gpio_mic_mute_hook() to control
the led.

[Hui: And there are two places to register the input device, to make
the code simple and clean, move the two same code sections into a
function.]

Cc: <stable@vger.kernel.org>
Signed-off-by: Kailang <kailang@realtek.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 23adc192 ]

We have two latest thinkpad laptop models which are all based on the
Intel skylake platforms, and all of them have the codec alc293 on
them. When the machines boot to the desktop, an greeting dialogue
shows up with the notification sound. But on these two models, there
is noise with the notification sound. We have 3 SKUs for each of
the models, all of them have this problem.

So far, this problem is only specific to these two thinkpad models,
we did not find this problem on the old thinkpad models with the
codec alc293 or alc292.

A workaround for this problem is disabling the aamix.

Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/bugs/1523517Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 8c69729b ]

We have a machine Dell XPS 13 with the codec alc256, after resume back
from S3, the headphone has noise when play sound.

Through comparing with the coeff vaule before and after S3, we found
restoring a coeff register will help remove noise.

BugLink: https://bugs.launchpad.net/bugs/1519168
Cc: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 6ed1131f ]

This machine had I2S codec for speaker output.
It need to refill the I2S codec initial verb after resume back.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Reported-and-tested-by: George Gugulea <gugulea@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 977e6276 ]

Dell create new platform with ALC298 codec.
This patch will enable headset mode for ALC298/ALC3266 platform.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit d144dfea ]

If we use USB ID pin as wakeup source, and there is a USB block
device on this USB OTG (ID) cable, the system will be deadlock
after system resume.

The root cause for this problem is: the workqueue ci_otg may try
to remove hcd before the driver resume has finished, and hcd will
disconnect the device on it, then, it will call device_release_driver,
and holds the device lock "dev->mutex", but it is never unlocked since
it waits workqueue writeback to run to flush the block information, but
the workqueue writeback is freezable, it is not thawed before driver
resume has finished.

When the driver (device: sd 0:0:0:0:) resume goes to dpm_complete, it
tries to get its device lock "dev->mutex", but it can't get it forever,
then the deadlock occurs. Below call stacks show the situation.

So, in order to fix this problem, we need to change workqueue ci_otg
as freezable, then the work item in this workqueue will be run after
driver's resume, this workqueue will not be blocked forever like above
case since the workqueue writeback has been thawed too.

Tested at: i.mx6qdl-sabresd and i.mx6sx-sdb.

[  555.178869] kworker/u2:13   D c07de74c     0   826      2 0x00000000
[  555.185310] Workqueue: ci_otg ci_otg_work
[  555.189353] Backtrace:
[  555.191849] [<c07de4fc>] (__schedule) from [<c07dec6c>] (schedule+0x48/0xa0)
[  555.198912]  r10:ee471ba0 r9:00000000 r8:00000000 r7:00000002 r6:ee470000 r5:ee471ba4
[  555.206867]  r4:ee470000
[  555.209453] [<c07dec24>] (schedule) from [<c07e2fc4>] (schedule_timeout+0x15c/0x1e0)
[  555.217212]  r4:7fffffff r3:edc2b000
[  555.220862] [<c07e2e68>] (schedule_timeout) from [<c07df6c8>] (wait_for_common+0x94/0x144)
[  555.229140]  r8:00000000 r7:00000002 r6:ee470000 r5:ee471ba4 r4:7fffffff
[  555.235980] [<c07df634>] (wait_for_common) from [<c07df790>] (wait_for_completion+0x18/0x1c)
[  555.244430]  r10:00000001 r9:c0b5563c r8:c0042e48 r7:ef086000 r6:eea4372c r5:ef131b00
[  555.252383]  r4:00000000
[  555.254970] [<c07df778>] (wait_for_completion) from [<c0043cb8>] (flush_work+0x19c/0x234)
[  555.263177] [<c0043b1c>] (flush_work) from [<c0043fac>] (flush_delayed_work+0x48/0x4c)
[  555.271106]  r8:ed5b5000 r7:c0b38a3c r6:eea439cc r5:eea4372c r4:eea4372c
[  555.277958] [<c0043f64>] (flush_delayed_work) from [<c00eae18>] (bdi_unregister+0x84/0xec)
[  555.286236]  r4:eea43520 r3:20000153
[  555.289885] [<c00ead94>] (bdi_unregister) from [<c02c2154>] (blk_cleanup_queue+0x180/0x29c)
[  555.298250]  r5:eea43808 r4:eea43400
[  555.301909] [<c02c1fd4>] (blk_cleanup_queue) from [<c0417914>] (__scsi_remove_device+0x48/0xb8)
[  555.310623]  r7:00000000 r6:20000153 r5:ededa950 r4:ededa800
[  555.316403] [<c04178cc>] (__scsi_remove_device) from [<c0415e90>] (scsi_forget_host+0x64/0x68)
[  555.325028]  r5:ededa800 r4:ed5b5000
[  555.328689] [<c0415e2c>] (scsi_forget_host) from [<c0409828>] (scsi_remove_host+0x78/0x104)
[  555.337054]  r5:ed5b5068 r4:ed5b5000
[  555.340709] [<c04097b0>] (scsi_remove_host) from [<c04cdfcc>] (usb_stor_disconnect+0x50/0xb4)
[  555.349247]  r6:ed5b56e4 r5:ed5b5818 r4:ed5b5690 r3:00000008
[  555.355025] [<c04cdf7c>] (usb_stor_disconnect) from [<c04b3bc8>] (usb_unbind_interface+0x78/0x25c)
[  555.363997]  r8:c13919b4 r7:edd3c000 r6:edd3c020 r5:ee551c68 r4:ee551c00 r3:c04cdf7c
[  555.371892] [<c04b3b50>] (usb_unbind_interface) from [<c03dc248>] (__device_release_driver+0x8c/0x118)
[  555.381213]  r10:00000001 r9:edd90c00 r8:c13919b4 r7:ee551c68 r6:c0b546e0 r5:c0b5563c
[  555.389167]  r4:edd3c020
[  555.391752] [<c03dc1bc>] (__device_release_driver) from [<c03dc2fc>] (device_release_driver+0x28/0x34)
[  555.401071]  r5:edd3c020 r4:edd3c054
[  555.404721] [<c03dc2d4>] (device_release_driver) from [<c03db304>] (bus_remove_device+0xe0/0x110)
[  555.413607]  r5:edd3c020 r4:ef17f04c
[  555.417253] [<c03db224>] (bus_remove_device) from [<c03d8128>] (device_del+0x114/0x21c)
[  555.425270]  r6:edd3c028 r5:edd3c020 r4:ee551c00 r3:00000000
[  555.431045] [<c03d8014>] (device_del) from [<c04b1560>] (usb_disable_device+0xa4/0x1e8)
[  555.439061]  r8:edd3c000 r7:eded8000 r6:00000000 r5:00000001 r4:ee551c00
[  555.445906] [<c04b14bc>] (usb_disable_device) from [<c04a8e54>] (usb_disconnect+0x74/0x224)
[  555.454271]  r9:edd90c00 r8:ee551000 r7:ee551c68 r6:ee551c9c r5:ee551c00 r4:00000001
[  555.462156] [<c04a8de0>] (usb_disconnect) from [<c04a8fb8>] (usb_disconnect+0x1d8/0x224)
[  555.470259]  r10:00000001 r9:edd90000 r8:ee471e2c r7:ee551468 r6:ee55149c r5:ee551400
[  555.478213]  r4:00000001
[  555.480797] [<c04a8de0>] (usb_disconnect) from [<c04ae5ec>] (usb_remove_hcd+0xa0/0x1ac)
[  555.488813]  r10:00000001 r9:ee471eb0 r8:00000000 r7:ef3d9500 r6:eded810c r5:eded80b0
[  555.496765]  r4:eded8000
[  555.499351] [<c04ae54c>] (usb_remove_hcd) from [<c04d4158>] (host_stop+0x28/0x64)
[  555.506847]  r6:eeb50010 r5:eded8000 r4:eeb51010
[  555.511563] [<c04d4130>] (host_stop) from [<c04d09b8>] (ci_otg_work+0xc4/0x124)
[  555.518885]  r6:00000001 r5:eeb50010 r4:eeb502a0 r3:c04d4130
[  555.524665] [<c04d08f4>] (ci_otg_work) from [<c00454f0>] (process_one_work+0x194/0x420)
[  555.532682]  r6:ef086000 r5:eeb502a0 r4:edc44480
[  555.537393] [<c004535c>] (process_one_work) from [<c00457b0>] (worker_thread+0x34/0x514)
[  555.545496]  r10:edc44480 r9:ef086000 r8:c0b1a100 r7:ef086034 r6:00000088 r5:edc44498
[  555.553450]  r4:ef086000
[  555.556032] [<c004577c>] (worker_thread) from [<c004bab4>] (kthread+0xdc/0xf8)
[  555.563268]  r10:00000000 r9:00000000 r8:00000000 r7:c004577c r6:edc44480 r5:eddc15c0
[  555.571221]  r4:00000000
[  555.573804] [<c004b9d8>] (kthread) from [<c000fef0>] (ret_from_fork+0x14/0x24)
[  555.581040]  r7:00000000 r6:00000000 r5:c004b9d8 r4:eddc15c0

[  553.429383] sh              D c07de74c     0   694    691 0x00000000
[  553.435801] Backtrace:
[  553.438295] [<c07de4fc>] (__schedule) from [<c07dec6c>] (schedule+0x48/0xa0)
[  553.445358]  r10:edd3c054 r9:edd3c078 r8:edddbd50 r7:edcbbc00 r6:c1377c34 r5:60000153
[  553.453313]  r4:eddda000
[  553.455896] [<c07dec24>] (schedule) from [<c07deff8>] (schedule_preempt_disabled+0x10/0x14)
[  553.464261]  r4:edd3c058 r3:0000000a
[  553.467910] [<c07defe8>] (schedule_preempt_disabled) from [<c07e0bbc>] (mutex_lock_nested+0x1a0/0x3e8)
[  553.477254] [<c07e0a1c>] (mutex_lock_nested) from [<c03e927c>] (dpm_complete+0xc0/0x1b0)
[  553.485358]  r10:00561408 r9:edd3c054 r8:c0b4863c r7:edddbd90 r6:c0b485d8 r5:edd3c020
[  553.493313]  r4:edd3c0d0
[  553.495896] [<c03e91bc>] (dpm_complete) from [<c03e9388>] (dpm_resume_end+0x1c/0x20)
[  553.503652]  r9:00000000 r8:c0b1a9d0 r7:c1334ec0 r6:c1334edc r5:00000003 r4:00000010
[  553.511544] [<c03e936c>] (dpm_resume_end) from [<c0079894>] (suspend_devices_and_enter+0x158/0x504)
[  553.520604]  r4:00000000 r3:c1334efc
[  553.524250] [<c007973c>] (suspend_devices_and_enter) from [<c0079e74>] (pm_suspend+0x234/0x2cc)
[  553.532961]  r10:00561408 r9:ed6b7300 r8:00000004 r7:c1334eec r6:00000000 r5:c1334ee8
[  553.540914]  r4:00000003
[  553.543493] [<c0079c40>] (pm_suspend) from [<c0078a6c>] (state_store+0x6c/0xc0)

[  555.703684] 7 locks held by kworker/u2:13/826:
[  555.708140]  #0:  ("%s""ci_otg"){++++.+}, at: [<c0045484>] process_one_work+0x128/0x420
[  555.716277]  #1:  ((&ci->work)){+.+.+.}, at: [<c0045484>] process_one_work+0x128/0x420
[  555.724317]  #2:  (usb_bus_list_lock){+.+.+.}, at: [<c04ae5e4>] usb_remove_hcd+0x98/0x1ac
[  555.732626]  #3:  (&dev->mutex){......}, at: [<c04a8e28>] usb_disconnect+0x48/0x224
[  555.740403]  #4:  (&dev->mutex){......}, at: [<c04a8e28>] usb_disconnect+0x48/0x224
[  555.748179]  #5:  (&dev->mutex){......}, at: [<c03dc2f4>] device_release_driver+0x20/0x34
[  555.756487]  #6:  (&shost->scan_mutex){+.+.+.}, at: [<c04097d0>] scsi_remove_host+0x20/0x104

Cc: <stable@vger.kernel.org> #v3.14+
Cc: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit dbc0d3ca ]

ceph_msg_footer is 21 bytes long, while ceph_msg_footer_old is only 13.
Don't skip too much when CEPH_FEATURE_MSG_AUTH isn't negotiated.

Cc: stable@vger.kernel.org # 3.19+
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit e7a88e82 ]

The contract between try_read() and try_write() is that when called
each processes as much data as possible.  When instructed by osd_client
to skip a message, try_read() is violating this contract by returning
after receiving and discarding a single message instead of checking for
more.  try_write() then gets a chance to write out more requests,
generating more replies/skips for try_read() to handle, forcing the
messenger into a starvation loop.

Cc: stable@vger.kernel.org # 3.10+
Reported-by: Varada Kari <Varada.Kari@sandisk.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Tested-by: Varada Kari <Varada.Kari@sandisk.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit d045437a ]

The ftrace:function event is only displayed for parsing the function tracer
data. It is not used to enable function tracing, and does not include an
"enable" file in its event directory.

Originally, this event was kept separate from other events because it did
not have a ->reg parameter. But perf added a "reg" parameter for its use
which caused issues, because it made the event available to functions where
it was not compatible for.

Commit 9b63776f "tracing: Do not enable function event with enable"
added a TRACE_EVENT_FL_IGNORE_ENABLE flag that prevented the function event
from being enabled by normal trace events. But this commit missed keeping
the function event from being displayed by the "available_events" directory,
which is used to show what events can be enabled by set_event.

One documented way to enable all events is to:

 cat available_events > set_event

But because the function event is displayed in the available_events, this
now causes an INVALID error:

 cat: write error: Invalid argument
Reported-by: Chunyu Hu <chuhu@redhat.com>
Fixes: 9b63776f "tracing: Do not enable function event with enable"
Cc: stable@vger.kernel.org # 3.4+
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit d7444794 ]

In async_pf we try to allocate with NOWAIT to get an element quickly
or fail. This code also handle failures gracefully. Lets silence
potential page allocation failures under load.

qemu-system-s39: page allocation failure: order:0,mode:0x2200000
[...]
Call Trace:
([<00000000001146b8>] show_trace+0xf8/0x148)
[<000000000011476a>] show_stack+0x62/0xe8
[<00000000004a36b8>] dump_stack+0x70/0x98
[<0000000000272c3a>] warn_alloc_failed+0xd2/0x148
[<000000000027709e>] __alloc_pages_nodemask+0x94e/0xb38
[<00000000002cd36a>] new_slab+0x382/0x400
[<00000000002cf7ac>] ___slab_alloc.constprop.30+0x2dc/0x378
[<00000000002d03d0>] kmem_cache_alloc+0x160/0x1d0
[<0000000000133db4>] kvm_setup_async_pf+0x6c/0x198
[<000000000013dee8>] kvm_arch_vcpu_ioctl_run+0xd48/0xd58
[<000000000012fcaa>] kvm_vcpu_ioctl+0x372/0x690
[<00000000002f66f6>] do_vfs_ioctl+0x3be/0x510
[<00000000002f68ec>] SyS_ioctl+0xa4/0xb8
[<0000000000781c5e>] system_call+0xd6/0x264
[<000003ffa24fa06a>] 0x3ffa24fa06a

Cc: stable@vger.kernel.org
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 172b2386 ]

Sometimes when setting a breakpoint a process doesn't stop on it.
This is because the debug registers are not loaded correctly on
VCPU load.

The following simple reproducer from Oleg Nesterov tries using debug
registers in two threads.  To see the bug, run a 2-VCPU guest with
"taskset -c 0" and run "./bp 0 1" inside the guest.

    #include <unistd.h>
    #include <signal.h>
    #include <stdlib.h>
    #include <stdio.h>
    #include <sys/wait.h>
    #include <sys/ptrace.h>
    #include <sys/user.h>
    #include <asm/debugreg.h>
    #include <assert.h>

    #define offsetof(TYPE, MEMBER) ((size_t) &((TYPE *)0)->MEMBER)

    unsigned long encode_dr7(int drnum, int enable, unsigned int type, unsigned int len)
    {
        unsigned long dr7;

        dr7 = ((len | type) & 0xf)
            << (DR_CONTROL_SHIFT + drnum * DR_CONTROL_SIZE);
        if (enable)
            dr7 |= (DR_GLOBAL_ENABLE << (drnum * DR_ENABLE_SIZE));

        return dr7;
    }

    int write_dr(int pid, int dr, unsigned long val)
    {
        return ptrace(PTRACE_POKEUSER, pid,
                offsetof (struct user, u_debugreg[dr]),
                val);
    }

    void set_bp(pid_t pid, void *addr)
    {
        unsigned long dr7;
        assert(write_dr(pid, 0, (long)addr) == 0);
        dr7 = encode_dr7(0, 1, DR_RW_EXECUTE, DR_LEN_1);
        assert(write_dr(pid, 7, dr7) == 0);
    }

    void *get_rip(int pid)
    {
        return (void*)ptrace(PTRACE_PEEKUSER, pid,
                offsetof(struct user, regs.rip), 0);
    }

    void test(int nr)
    {
        void *bp_addr = &&label + nr, *bp_hit;
        int pid;

        printf("test bp %d\n", nr);
        assert(nr < 16); // see 16 asm nops below

        pid = fork();
        if (!pid) {
            assert(ptrace(PTRACE_TRACEME, 0,0,0) == 0);
            kill(getpid(), SIGSTOP);
            for (;;) {
                label: asm (
                    "nop; nop; nop; nop;"
                    "nop; nop; nop; nop;"
                    "nop; nop; nop; nop;"
                    "nop; nop; nop; nop;"
                );
            }
        }

        assert(pid == wait(NULL));
        set_bp(pid, bp_addr);

        for (;;) {
            assert(ptrace(PTRACE_CONT, pid, 0, 0) == 0);
            assert(pid == wait(NULL));

            bp_hit = get_rip(pid);
            if (bp_hit != bp_addr)
                fprintf(stderr, "ERR!! hit wrong bp %ld != %d\n",
                    bp_hit - &&label, nr);
        }
    }

    int main(int argc, const char *argv[])
    {
        while (--argc) {
            int nr = atoi(*++argv);
            if (!fork())
                test(nr);
        }

        while (wait(NULL) > 0)
            ;
        return 0;
    }

Cc: stable@vger.kernel.org
Suggested-by: Nadav Amit <namit@cs.technion.ac.il>
Reported-by: Andrey Wagin <avagin@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 236cf17c ]

When we allocate bitmaps in vgic_vcpu_init_maps, we divide the number of
bits we need by 8 to figure out how many bytes to allocate. However,
bitmap elements are always accessed as unsigned longs, and if we didn't
happen to allocate a size such that size % sizeof(unsigned long) == 0,
bitmap accesses may go past the end of the allocation.

When using KASAN (which does byte-granular access checks), this results
in a continuous stream of BUGs whenever these bitmaps are accessed:

=============================================================================
BUG kmalloc-128 (Tainted: G    B          ): kasan: bad access detected
-----------------------------------------------------------------------------

INFO: Allocated in vgic_init.part.25+0x55c/0x990 age=7493 cpu=3 pid=1730
INFO: Slab 0xffffffbde6d5da40 objects=16 used=15 fp=0xffffffc935769700 flags=0x4000000000000080
INFO: Object 0xffffffc935769500 @offset=1280 fp=0x          (null)

Bytes b4 ffffffc9357694f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Object ffffffc935769500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Object ffffffc935769510: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Object ffffffc935769520: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Object ffffffc935769530: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Object ffffffc935769540: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Object ffffffc935769550: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Object ffffffc935769560: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Object ffffffc935769570: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Padding ffffffc9357695b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Padding ffffffc9357695c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Padding ffffffc9357695d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Padding ffffffc9357695e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Padding ffffffc9357695f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
CPU: 3 PID: 1740 Comm: kvm-vcpu-0 Tainted: G    B           4.4.0+ #17
Hardware name: ARM Juno development board (r1) (DT)
Call trace:
[<ffffffc00008e770>] dump_backtrace+0x0/0x280
[<ffffffc00008ea04>] show_stack+0x14/0x20
[<ffffffc000726360>] dump_stack+0x100/0x188
[<ffffffc00030d324>] print_trailer+0xfc/0x168
[<ffffffc000312294>] object_err+0x3c/0x50
[<ffffffc0003140fc>] kasan_report_error+0x244/0x558
[<ffffffc000314548>] __asan_report_load8_noabort+0x48/0x50
[<ffffffc000745688>] __bitmap_or+0xc0/0xc8
[<ffffffc0000d9e44>] kvm_vgic_flush_hwstate+0x1bc/0x650
[<ffffffc0000c514c>] kvm_arch_vcpu_ioctl_run+0x2ec/0xa60
[<ffffffc0000b9a6c>] kvm_vcpu_ioctl+0x474/0xa68
[<ffffffc00036b7b0>] do_vfs_ioctl+0x5b8/0xcb0
[<ffffffc00036bf34>] SyS_ioctl+0x8c/0xa0
[<ffffffc000086cb0>] el0_svc_naked+0x24/0x28
Memory state around the buggy address:
 ffffffc935769400: 00 00 fc fc fc fc fc fc fc fc fc fc fc fc fc fc
 ffffffc935769480: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffffffc935769500: 04 fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
                   ^
 ffffffc935769580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
 ffffffc935769600: 00 00 00 00 fc fc fc fc fc fc fc fc fc fc fc fc
==================================================================

Fix the issue by always allocating a multiple of sizeof(unsigned long),
as we do elsewhere in the vgic code.

Fixes: c1bfb577 ("arm/arm64: KVM: vgic: switch to dynamic allocation")
Cc: stable@vger.kernel.org
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit b7052cd7 ]

The qword_get() function NUL-terminates its output buffer.  If the input
string is in hex format \xXXXX... and the same length as the output
buffer, there is an off-by-one:

  int qword_get(char **bpp, char *dest, int bufsize)
  {
      ...
      while (len < bufsize) {
          ...
          *dest++ = (h << 4) | l;
          len++;
      }
      ...
      *dest = '\0';
      return len;
  }

This patch ensures the NUL terminator doesn't fall outside the output
buffer.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 39d42750 ]

set_power_state defaults to no displays, so we need to update
the display configuration after setting up the powerstate on the
first call. In most cases this is not an issue since ends up
getting called multiple times at any given modeset and the proper
order is achieved in the display changed handling at the top of
the function.
Reviewed-by: Christian König <christian.koenig@amd.com>
Acked-by: Jordan Lazare <Jordan.Lazare@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 342300cc ]

git commit 80703617
"s390: add support for vector extension"
broke 31-bit compat processes in regard to signal handling.

The restore_sigregs_ext32() function is used to restore the additional
elements from the user space signal frame. Among the additional elements
are the upper registers halves for 64-bit register support for 31-bit
processes. The copy_from_user that is used to retrieve the high-gprs
array from the user stack uses an incorrect length, 8 bytes instead of
64 bytes. This causes incorrect upper register halves to get loaded.

Cc: stable@vger.kernel.org # 3.8+
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 4328daa2 ]

Using request-based DM mpath configured with the following stacking
(.request_fn DM mpath ontop of scsi-mq paths):

echo Y > /sys/module/scsi_mod/parameters/use_blk_mq
echo N > /sys/module/dm_mod/parameters/use_blk_mq

'struct dm_rq_target_io' would leak if a request is requeued before a
blk-mq clone is allocated (or fails to allocate).  free_rq_tio()
wasn't being called.

kmemleak reported:

unreferenced object 0xffff8800b90b98c0 (size 112):
  comm "kworker/7:1H", pid 5692, jiffies 4295056109 (age 78.589s)
  hex dump (first 32 bytes):
    00 d0 5c 2c 03 88 ff ff 40 00 bf 01 00 c9 ff ff  ..\,....@.......
    e0 d9 b1 34 00 88 ff ff 00 00 00 00 00 00 00 00  ...4............
  backtrace:
    [<ffffffff81672b6e>] kmemleak_alloc+0x4e/0xb0
    [<ffffffff811dbb63>] kmem_cache_alloc+0xc3/0x1e0
    [<ffffffff8117eae5>] mempool_alloc_slab+0x15/0x20
    [<ffffffff8117ec1e>] mempool_alloc+0x6e/0x170
    [<ffffffffa00029ac>] dm_old_prep_fn+0x3c/0x180 [dm_mod]
    [<ffffffff812fbd78>] blk_peek_request+0x168/0x290
    [<ffffffffa0003e62>] dm_request_fn+0xb2/0x1b0 [dm_mod]
    [<ffffffff812f66e3>] __blk_run_queue+0x33/0x40
    [<ffffffff812f9585>] blk_delay_work+0x25/0x40
    [<ffffffff81096fff>] process_one_work+0x14f/0x3d0
    [<ffffffff81097715>] worker_thread+0x125/0x4b0
    [<ffffffff8109ce88>] kthread+0xd8/0xf0
    [<ffffffff8167cb8f>] ret_from_fork+0x3f/0x70
    [<ffffffffffffffff>] 0xffffffffffffffff

crash> struct -o dm_rq_target_io
struct dm_rq_target_io {
    ...
}
SIZE: 112

Fixes: e5863d9a ("dm: allocate requests in target when stacking on blk-mq devices")
Cc: stable@vger.kernel.org # 4.0+
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 90cfde46 ]

This patch fixes the problem that more CAN messages could be sent to the
interface as could be send on the CAN bus. This was more likely for slow baud
rates. The sleeping _start_xmit was woken up in the _write_bulk_callback. Under
heavy TX load this produced another bulk transfer without checking the
free_slots variable and hence caused the overflow in the interface.
Signed-off-by: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 7a64cd88 ]

There's one point was missed in the patch commit da49889d ("staging:
binder: Support concurrent 32 bit and 64 bit processes."). When configure
BINDER_IPC_32BIT, the size of binder_uintptr_t was 32bits, but size of
void * is 64bit on 64bit system. Correct it here.
Signed-off-by: Lisa Du <cldu@marvell.com>
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Fixes: da49889d ("staging: binder: Support concurrent 32 bit and 64 bit processes.")
Cc: <stable@vger.kernel.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 000e0949 ]

Thermal hook gpio_fan_get_cur_state is only interested in knowing
the current speed index that was setup in the system, this is
already available as part of fan_data->speed_index which is always
set by set_fan_speed. Using get_fan_speed_index is useful when we
have no idea about the fan speed configuration (for example during
fan_ctrl_init).

When thermal framework invokes
gpio_fan_get_cur_state=>get_fan_speed_index via gpio_fan_get_cur_state
especially in a polled configuration for thermal governor, we
basically hog the i2c interface to the extent that other functions
fail to get any traffic out :(.

Instead, just provide the last state set in the driver - since the gpio
fan driver is responsible for the fan state immaterial of override, the
fan_data->speed_index should accurately reflect the state.

Fixes: b5cf88e4 ("(gpio-fan): Add thermal control hooks")
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit acc14694 ]

Make the divisor signed as DIV_ROUND_CLOSEST is undefined for negative
dividends when the divisor is unsigned.
Signed-off-by: Peter Rosin <peda@axentia.se>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit f5bdd66c ]

This patch complements the list of device IDs previously
added for lewisburg sata.
Signed-off-by: Alexandra Yates <alexandra.yates@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 56e74338 ]

Adding Intel codename Lewisburg platform device IDs for SATA.
Signed-off-by: Alexandra Yates <alexandra.yates@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 4d92f009 ]

This change was to preserve the ascending order of device IDs.
There was an exception with the first two Lewisburg device IDs to
keep all device IDs of the same kind grouped by code name.
Signed-off-by: Alexandra Yates <alexandra.yates@linux.intel.com>
signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit d061c1ca ]

Thomas reports:

T:  Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=  4 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=05c6 ProdID=6001 Rev=00.00
S:  Manufacturer=USB Modem
S:  Product=USB Modem
S:  SerialNumber=1234567890ABCDEF
C:  #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage

Cc: <stable@vger.kernel.org>
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 6627ae19 ]

Add USB ID for cp2104/5 devices on GE B650v3 and B850v3 boards.
Signed-off-by: Ken Lin <ken.lin@advantech.com.tw>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 3158a8d4 ]

$ lsusb:
Bus 001 Device 101: ID 1e0e:9001 Qualcomm / Option

$ usb-devices:
T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=101 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  2
P:  Vendor=1e0e ProdID=9001 Rev= 2.32
S:  Manufacturer=SimTech, Incorporated
S:  Product=SimTech, Incorporated
S:  SerialNumber=0123456789ABCDEF
C:* #Ifs= 7 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)

The last interface (6) is used for Android Composite ADB interface.

Serial port layout:
0: QCDM/DIAG
1: NMEA
2: AT
3: AT/PPP
4: audio
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit d9dfd8d7 ]

In the case where d_add_unique() finds an appropriate alias to use it will
have already incremented the reference count.  An additional dget() to swap
the open context's dentry is unnecessary and will leak a reference.
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Fixes: 275bb307 ("NFSv4: Move dentry instantiation into the NFSv4-...")
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit c4509601 ]

The assignement of EP transfer resources was not handled properly in the
dwc3 driver. Commit aebda618 ("usb: dwc3: Reset the transfer
resource index on SET_INTERFACE") previously fixed one aspect of this
where resources may be exhausted with multiple calls to SET_INTERFACE.
However, it introduced an issue where composite devices with multiple
interfaces can be assigned the same transfer resources for different
endpoints. This patch solves both issues.

The assignment of transfer resources cannot perfectly follow the data
book due to the fact that the controller driver does not have all
knowledge of the configuration in advance. It is given this information
piecemeal by the composite gadget framework after every
SET_CONFIGURATION and SET_INTERFACE. Trying to follow the databook
programming model in this scenario can cause errors. For two reasons:

1) The databook says to do DEPSTARTCFG for every SET_CONFIGURATION and
SET_INTERFACE (8.1.5). This is incorrect in the scenario of multiple
interfaces.

2) The databook does not mention doing more DEPXFERCFG for new endpoint
on alt setting (8.1.6).

The following simplified method is used instead:

All hardware endpoints can be assigned a transfer resource and this
setting will stay persistent until either a core reset or hibernation.
So whenever we do a DEPSTARTCFG(0) we can go ahead and do DEPXFERCFG for
every hardware endpoint as well. We are guaranteed that there are as
many transfer resources as endpoints.

This patch triggers off of the calling dwc3_gadget_start_config() for
EP0-out, which always happens first, and which should only happen in one
of the above conditions.

Fixes: aebda618 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE")
Cc: <stable@vger.kernel.org> # v3.2+
Reported-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>