- 19 Feb, 2021 4 commits
-
-
Gerd Hoffmann authored
Call qxl_bo_unpin (which does a reservation) without holding the release_mutex lock. Fixes lockdep (correctly) warning on a possible deadlock. Fixes: 65ffea3c ("drm/qxl: unpin release objects") Signed-off-by:
Gerd Hoffmann <kraxel@redhat.com> Acked-by:
Thomas Zimmermann <tzimmermann@suse.de> Link: http://patchwork.freedesktop.org/patch/msgid/20210217123213.2199186-5-kraxel@redhat.com
-
Gerd Hoffmann authored
Allow to set priorities for buffer objects. Use priority 1 for surface and cursor command releases. Use priority 0 for drawing command releases. That way the short-living drawing commands are first in line when it comes to eviction, making it *much* less likely that ttm_bo_mem_force_space() picks something which can't be evicted and throws an error after waiting a while without success. Signed-off-by:
-
Gerd Hoffmann authored
Move qxl_io_notify_oom() call into wait condition. That way the driver will call it again if one call wasn't enough. Also allows to remove the extra dma_fence_is_signaled() check and the goto. Fixes: 5a838e5d ("drm/qxl: simplify qxl_fence_wait") Signed-off-by:
-
Gerd Hoffmann authored
Specifically do not try release resources which where not allocated in the first place. Cc: Tong Zhang <ztong0001@gmail.com> Tested-by:
Tong Zhang <ztong0001@gmail.com> Signed-off-by:
-
- 18 Feb, 2021 6 commits
-
-
Dario Binacchi authored
The fdd property of the tilcdc_panel_info structure must set the reqdly bit field (bit 12 to 19) of the raster control register. The previous statement set the least significant bit instead. Signed-off-by:
Dario Binacchi <dariobin@libero.it> Reviewed-by:
Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Reviewed-by:
Jyri Sarha <jyri.sarha@iki.fi> Tested-by:
-
Tian Tao authored
The code has been in a irq-disabled context since it is hard IRQ. There is no necessity to do it again. Signed-off-by:
Tian Tao <tiantao6@hisilicon.com> Reviewed-by:
-
Imre Deak authored
It's possible to modeset a connector/mst port that has a 0 full_pbn value: if the sink on the port deasserts its HPD and a branch device reports this via a CSN with the port's ddps=0 and pdt!=NONE the driver clears full_pbn, but the corresponding connector can be still modesetted. This happened on a DELL U2719D monitor as the branch device and an LG 27UL650-W daisy-chained to it, the LG monitor generating a long HPD pulse (doing this for some reason always when waking up from some power saving state). Tune down the WARN about this scenario to a debug message. v2: Use the correct atomic debug message level. (Lyude) References: https://gitlab.freedesktop.org/drm/intel/-/issues/1917 Cc: Lyude Paul <lyude@redhat.com> Signed-off-by:
Imre Deak <imre.deak@intel.com> Reviewed-by:
Lyude Paul <lyude@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210216123448.410545-1-imre.deak@intel.com
-
Sebastian Andrzej Siewior authored
The driver uses in_atomic() to distinguish between mdelay() and msleep(). The usage of in_interrupt() in drivers is phased out and Linus clearly requested that code which changes behaviour depending on context should either be separated or the context be conveyed in an argument passed by the caller, which usually knows the context. I traced the usage of in_interrupt() back to its initial merge: bfe694f8 ("[ARM] Add ARM AMBA CLCD framebuffer driver.") https://git.kernel.org/history/history/c/bfe694f833643 The driver has been removed and added back in the meantime. I've been looking for the IRQ context as described in the comment and couldn't find it. The functions calling clcdfb_sleep() also call conditionally backlight_update_status() which acquires a mutex. If it is okay to acquire a mutex then it is okay to use msleep() since both functions must be used in preemptible context. Replace clcdfb_sleep() with msleep(). Cc: Peter Collingbourne <pcc@google.com> Cc: Russell King <linux@armlinux.org.uk> Signed-off-by:Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20210208223810.388502-4-bigeasy@linutronix.de
-
Ahmed S. Darwish authored
dsi_sync_vc() uses in_interrupt() to create a warning if the function is used in non-preemptible context. The usage of in_interrupt() in drivers is phased out and Linus clearly requested that code which changes behaviour depending on context should either be separated or the context be conveyed in an argument passed by the caller, which usually knows the context. The wait_for_completion() function (used in dsi_sync_vc_vp() and dsi_sync_vc_l4() has already a check if it is invoked from proper context. Remove WARN_ON(in_interrupt()) from the driver. Cc: linux-omap@vger.kernel.org Signed-off-by:
Ahmed S. Darwish <a.darwish@linutronix.de> Signed-off-by:
-
Ahmed S. Darwish authored
alloc_req() uses in_interrupt() to detect if it is safe to use down(). The usage of in_interrupt() in drivers is phased out and Linus clearly requested that code which changes behaviour depending on context should either be separated or the context be conveyed in an argument passed by the caller, which usually knows the context. The semaphore is used as a counting semaphore, initialized with the number of slots in the request pool minus IRQ_REQ_POOL_SIZE - which are reserved for the in_interrupt() user to ensure that a request is always available. The preemptible user will block on the semphore waiting for a request to become available in case there are no requests available. Replace in_interrupt() with a `can_sleep' argument to indicate if it is safe to block on the sempahore. Cc: linux-omap@vger.kernel.org Signed-off-by:
-
- 17 Feb, 2021 13 commits
-
-
Sakari Ailus authored
Switch DRM drivers from drm_get_format_name() to %p4cc. This gets rid of a large number of temporary variables at the same time. Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Reviewed-by:
Petr Mladek <pmladek@suse.com> Reviewed-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by:
-
Sakari Ailus authored
Now that we can print FourCC codes directly using printk, make use of the feature in V4L2 core. Signed-off-by:
Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Reviewed-by:
-
Sakari Ailus authored
Add a printk modifier %p4cc (for pixel format) for printing V4L2 and DRM pixel formats denoted by fourccs. The fourcc encoding is the same for both so the same implementation can be used. Suggested-by:
Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by:
Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Reviewed-by:
-
Thomas Zimmermann authored
We used to update the cursor image in prepare_fb. Move all this code to atomic_update (where it belongs). The generic helper for shadow-buffered planes now implement the cursor plane's prepare_fb. Signed-off-by:
-
Thomas Zimmermann authored
As HW cursor BOs never move, we can store the offset in VRAM in the cursor-plane's HWC state. This removes the last possible source of runtime errors from atomic_update. Signed-off-by:
-
Thomas Zimmermann authored
The BOs of the hardware cursor are now mapped permanently while the cursor plane is being used. This reduces the CPU overhead of the cursor plane's atomic_update function. The change also resolves a problem with the vmap call in the commit tail. The vmap implementation could acquire the DMA reservation lock on the BO, which is not allowed that late in the atomic update. Removing the vmap call from atomic_update fixes the issue. Signed-off-by:
-
Thomas Zimmermann authored
The cursor uses two BOs in video RAM to implement double buffering. Store both in struct ast_cursor_plane. Signed-off-by:
-
Thomas Zimmermann authored
Cursor state is currently located throughout struct ast_private. Having struct ast_cursor_plane as dedicated data structure for cursors helps to organize the modesetting code. Signed-off-by:
-
Thomas Zimmermann authored
The logic for cursor updates is now located in the cursor plane's modesetting code. A number of helper functions remain to modify the rsp registers and image. Signed-off-by:
-
Thomas Zimmermann authored
The BOs are eventually released by the cursor plane's destroy callback. Signed-off-by:
-
Thomas Zimmermann authored
This change will help with inlining cursor functions into modesetting code. The primary plane's field used to be cleared with memset(). This has been dropped as the memory is always allocated with kzalloc(). Signed-off-by:
-
Thomas Zimmermann authored
Use AST_MAX_HWC_HEIGHT for setting offset_y in the cursor plane's atomic_check. The code used AST_MAX_HWC_WIDTH instead. This worked because both constants has the same value. Signed-off-by:
-
Thomas Zimmermann authored
Set the bits in VGACRCB with constants. Alo move the rsp code into a helper function. Signed-off-by:
-
- 15 Feb, 2021 4 commits
-
-
Marek Vasut authored
The drm_display_mode_to_videomode() does not populate DISPLAY_FLAGS_DE_LOW or DISPLAY_FLAGS_PIXDATA_NEGEDGE flags in struct videomode. Therefore, no matter what polarity the next bridge or display might require, these flags are never set, and thus the LTDC GCR_DEPOL and GCR_PCPOL bits are never set and the LTDC behaves as if both DISPLAY_FLAGS_PIXDATA_POSEDGE and DISPLAY_FLAGS_DE_HIGH were always set. The fix for this problem is taken almost verbatim from MXSFB driver. In case there is a bridge attached to the LTDC, the bridge might have extra polarity requirements, so extract bus_flags from the bridge and use them for LTDC configuration. Otherwise, extract bus_flags from the connector, which is the display. Fixes: b759012c ("drm/stm: Add STM32 LTDC driver") Signed-off-by:
Marek Vasut <marex@denx.de> Signed-off-by:
Yannick Fertre <yannick.fertre@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Antonio Borneo <antonio.borneo@st.com> Cc: Benjamin Gaignard <benjamin.gaignard@st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Philippe Cornu <philippe.cornu@st.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Vincent Abriou <vincent.abriou@st.com> Cc: Yannick Fertre <yannick.fertre@st.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-stm32@st-md-mailman.stormreply.com To: dri-devel@lists.freedesktop.org Tested-by:
Yannick Fertre <yannick.fertre@foss.st.com> Signed-off-by:
Philippe Cornu <philippe.cornu@foss.st.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210127110756.125570-1-marex@denx.de
-
Boris Brezillon authored
Doing a hw-irq -> threaded-irq round-trip is counter-productive, stay in the threaded irq handler as long as we can. v2: * Rework the loop to avoid a goto Signed-off-by:
Boris Brezillon <boris.brezillon@collabora.com> Reviewed-by:
Steven Price <steven.price@arm.com> Reviewed-by:
Rob Herring <robh@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20210205111757.585248-4-boris.brezillon@collabora.com
-
Boris Brezillon authored
We allocate 2MB chunks at a time, so it might appear that a page fault has already been handled by a previous page fault when we reach panfrost_mmu_map_fault_addr(). Bail out in that case to avoid mapping the same area twice. Cc: <stable@vger.kernel.org> Fixes: 187d2929 ("drm/panfrost: Add support for GPU heap allocations") Signed-off-by:
-
Boris Brezillon authored
When a fault is handled it will unblock the GPU which will continue executing its shader and might fault almost immediately on a different page. If we clear interrupts after handling the fault we might miss new faults, so clear them before. Cc: <stable@vger.kernel.org> Fixes: 187d2929 ("drm/panfrost: Add support for GPU heap allocations") Signed-off-by:
-
- 12 Feb, 2021 1 commit
-
-
Christian König authored
Swapping bo->mem was completely unecessary. Cleanup the function which is just a leftover from a TTM cleanup. Signed-off-by:
Christian König <christian.koenig@amd.com> Reviewed-by:
-
- 10 Feb, 2021 9 commits
-
-
Zack Rusin authored
There's no need to check for the presence of the hotplug property just to return because this is the end of the function so we're returning either way. Signed-off-by:
Zack Rusin <zackr@vmware.com> Reviewed-by:
Martin Krastev <krastevm@vmware.com> Reviewed-by:
Roland Scheidegger <sroland@vmware.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210209161700.335611-2-zackr@vmware.com
-
Zack Rusin authored
Our sysfs "modes" entries were broken because our preffered mode never had its name set correctly. This resulted in the first entry simply being called "preferred" followed by a list of other resolutions. Lets fix it by actually setting the name of mode (which is its resolution). This allows one to quickly validate the modes set by the open-vm-tools. Signed-off-by:
-
Roland Scheidegger authored
The default list was old and in particular lacking all common 16:9 resolutions, as well as some newer 16:10 ones. This makes them selectable in resolution change lists, which can be quite useful (for instance in case auto-fit isn't enabled). Signed-off-by:
-
Julia Lawall authored
Use getter and setter functions, for platform_device structures and a mipi_dsi_device structure. Signed-off-by:
Julia Lawall <Julia.Lawall@inria.fr> Signed-off-by:
-
Daniel Vetter authored
I got real badly confused when trying to review a fix from Ville for this. Let's try to document better what's required for this, and check the minimal settings at runtime - we can't check ofc that there's indeed no races in the driver callback. Also noticed that the drm_vblank_restore version is unused, so lets unexport that while at it. Reviewed-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Signed-off-by:
Daniel Vetter <daniel.vetter@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210209101523.2954281-1-daniel.vetter@ffwll.ch
-
Roman Stratiienko authored
DE3.0 VI layers supports plane-global alpha channel. DE2.0 FCC block have GLOBAL_ALPHA register that can be used as alpha source for blender. Add alpha property to the DRM plane and connect it to the corresponding registers in the mixer. Do not add alpha property for V3s SOC that have DE2.0 and 2 VI planes. Signed-off-by:
Roman Stratiienko <r.stratiienko@gmail.com> Reviewed-by:
Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by:
Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20210128113940.347013-3-r.stratiienko@gmail.com
-
Roman Stratiienko authored
DE2.0 and DE3.0 UI layers supports plane-global alpha channel. Add alpha property to the DRM plane and connect it to the corresponding registers in mixer. Signed-off-by:
-
Joel Stanley authored
There are minor differences in the values for the threshold value and the scan line size between families of ASPEED SoC. Additionally the SCU registers for the output control and scratch registers differ between families. This adds device tree matching to parameterise these values, allowing us to add support for the AST2400 now, and in the future the AST2600. Reviewed-by:
Jeremy Kerr <jk@ozlabs.org> Signed-off-by:
Joel Stanley <joel@jms.id.au> Link: https://patchwork.freedesktop.org/patch/msgid/20210209123734.130483-3-joel@jms.id.au
-
Joel Stanley authored
This scales better to multiple families of SoC. The lookup by compatible can be removed in a future change. The fallback path is for the ast2500 platform only. Other platforms will be added with the new style, so they won't need fallback paths. Signed-off-by:
Andrew Jeffery <andrew@aj.id.au> Link: https://patchwork.freedesktop.org/patch/msgid/20210209123734.130483-2-joel@jms.id.au
-
- 09 Feb, 2021 3 commits
-
-
Quanyang Wang authored
When run xrandr to change resolution on Beaglebone Black board, it will print the error information: root@beaglebone:~# xrandr -display :0 --output HDMI-1 --mode 720x400 [drm:drm_crtc_commit_wait] *ERROR* flip_done timed out [drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [CRTC:32:tilcdc crtc] commit wait timed out [drm:drm_crtc_commit_wait] *ERROR* flip_done timed out [drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [CONNECTOR:34:HDMI-A-1] commit wait timed out [drm:drm_crtc_commit_wait] *ERROR* flip_done timed out [drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [PLANE:31:plane-0] commit wait timed out tilcdc 4830e000.lcdc: already pending page flip! This is because there is operation sequence as below: drm_atomic_connector_commit_dpms(mode is DRM_MODE_DPMS_OFF): ... drm_atomic_helper_setup_commit <- init_completion(commit_A->flip_done) drm_atomic_helper_commit_tail tilcdc_crtc_atomic_disable tilcdc_plane_atomic_update <- drm_crtc_send_vblank_event in tilcdc_crtc_irq is skipped since tilcdc_crtc->enabled is 0 tilcdc_crtc_atomic_flush <- drm_crtc_send_vblank_event is skipped since crtc->state->event is set to be NULL in tilcdc_plane_atomic_update drm_mode_setcrtc: ... drm_atomic_helper_setup_commit <- init_completion(commit_B->flip_done) drm_atomic_helper_wait_for_dependencies drm_crtc_commit_wait <- wait for commit_A->flip_done completing Just as shown above, the steps which could complete commit_A->flip_done are all skipped and commit_A->flip_done will never be completed. This will result a time-out ERROR when drm_crtc_commit_wait check the commit_A->flip_done. So add drm_crtc_send_vblank_event in tilcdc_crtc_atomic_disable to complete commit_A->flip_done. Fixes: cb345dec ("drm/tilcdc: Use standard drm_atomic_helper_commit") Signed-off-by:Quanyang Wang <quanyang.wang@windriver.com> Reviewed-by:
-
Christian König authored
Not used any more. Signed-off-by:
-
Christian König authored
This is just another feature which is only used by VMWGFX, so move it into the driver instead. I've tried to add the accounting sysfs file to the kobject of the drm minor, but I'm not 100% sure if this works as expected. v2: fix typo in KFD and avoid 64bit divide v3: fix init order in VMWGFX v4: use pdev sysfs reference instead of drm Signed-off-by:
Nirmoy Das <nirmoy.das@amd.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210208133226.36955-2-christian.koenig@amd.com
-
