- 08 Apr, 2010 13 commits
-
-
Bob Copeland authored
These channels aren't selectable anyway, but our calculations for 2.5 mhz frequencies are incorrect. The value is supposed to be: (frequency - reference) * (10/25) i.e., divide by 2.5, but we were instead doing: (10 * frequency - reference) / 25. Additionally, the check for (frequency % 5 == 2) had an extra subtraction that wasn't in madwifi HAL. Signed-off-by: Bob Copeland <me@bobcopeland.com> Acked-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
Enhance tracing by adding tracing for a variety of callbacks that the drivers call, and also for internal calls (currently limited to queue status). This can aid debugging what is going on in mac80211 in interaction with drivers, since we can now see what drivers call and not just what mac80211 calls in the driver. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
rt2872 needs the same rf register setup as rt3070 and rt3090, hence use rt2800_config_channel_rt3x instead of rt2800_config_channel_rt2x. This change allows me to actually switch channels and hence scan all configured channels on the RT305x SoC platform (which uses a rt2872) here. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Tested-by: Luis Correia <luis.f.correia@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Pavel Roskin authored
Don't modify ah->iniModes, it's supposed to be constant. Instead, apply the fixup when the data is written to the registers. Change ath9k_hw_init_eeprom_fix() to only determine whether the fixup is needed. This allows similteneous support for AR9220 cards that need AR_AN_TOP2 fixup (such as Ubiquiti SR71-12) and those that don't need it (D-Link DWA-552 rev A2). Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
Messages that are generated by the HTC layer don't have any TX callback endpoints assigned to them. Consequently, the allocated SKBs are never freed. Fix this issue by handling this case in the HTC layer itself. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
hif_usb_regout_cb() frees the given URB, which is borked by design. Use an anchor to simplify URB management. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
The maximum number of packets in a single buffer in stream mode is 10. The driver currently uses 8 - which caused stack corruption, in the absence of any kind of OOB checking. Fixing this to the correct value of 10 fixes the module unload issue. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Tested-by: Ming Lei <tom.leiming@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
RX URBs are automatically freed when the reference count drops to zero - this currently doesn't happen when usb_kill_anchored_urbs() is called during unload. Fix this by dropping the reference count by one during initial submission. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
Use a spin lock to prevent concurrent access to variables dealing with RX stream mode handling. Currently, no protection is implemented - which causes problems in RX. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Gertjan van Wingerde authored
Now that the powersave issues on rt2500usb have been tackled, powersave can be enabled by default again. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Javier Cardona authored
Grouped mesh action codes together with the other action codes in ieee80211.h. Signed-off-by: Javier Cardona <javier@cozybit.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Frans Pop authored
Signed-off-by: Frans Pop <elendil@planet.nl> Cc: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
John W. Linville authored
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 into merge Conflicts: Documentation/feature-removal-schedule.txt drivers/net/wireless/ath/ath5k/phy.c drivers/net/wireless/iwlwifi/iwl-4965.c drivers/net/wireless/iwlwifi/iwl-agn.c drivers/net/wireless/iwlwifi/iwl-core.c drivers/net/wireless/iwlwifi/iwl-core.h drivers/net/wireless/iwlwifi/iwl-tx.c
-
- 07 Apr, 2010 13 commits
-
-
Johannes Berg authored
WEP crypto was broken, but upon finding the problem it is evident that other things were broken by the paged RX patch as well. To fix it, for now move the linearising in front. This means that we linearise all frames, which is not at all what we want, but at least it fixes the problem for now. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Acked-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
A few places in mac80211 do not currently acquire the sta lock for RX aggregation, but they should. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
The aggregation code has a number of quirks, like inventing an unneeded WLAN_BACK_TIMER value and leaking memory under certain circumstances during station destruction. Fix these issues by using the regular aggregation session teardown code and blocking new aggregation sessions, all before the station is really destructed. As a side effect, this gets rid of the long code block to destroy aggregation safely. Additionally, rename tid_state_rx which can only have the values IDLE and OPERATIONAL to tid_active_rx to make it easier to understand that there is no bitwise stuff going on on the RX side -- the TX side remains because it needs to keep track of the driver and peer states. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
I want to use it during station destruction as well so rename it to WLAN_STA_BLOCK_BA which is also the only use of it now. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
All callers of ieee80211_sta_stop_rx_ba_session can just call __ieee80211_stop_rx_ba_session instead because they already have the station struct, so do that and remove ieee80211_sta_stop_rx_ba_session. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
All other places except one in the TX path, which has BHs disabled, and it also cannot be locked from interrupts so disabling IRQs is not necessary. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
When a station w/o a key is destroyed, or when a driver submits work for a station and thereby references it again, it seems like potentially we could reference the station structure while it is being destroyed. Wait for an RCU grace period to elapse before finishing destroying the station after we have removed the station from the driver and from the hash table etc., even in the case where no key is associated with the station. Also, there's no point in deleting the plink timer here since it'll be properly deleted just a bit later. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Vivek Natarajan authored
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Vivek Natarajan authored
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Vivek Natarajan authored
This patch adds support for a modified newer version of AR9285 chipsets. Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Jouni Malinen authored
cfg80211 is quite strict on allowing authentication and association commands only in certain states. In order to meet these requirements, user space applications may need to clear authentication or association state in some cases. Currently, this can be done with deauth/disassoc command, but that ends up sending out Deauthentication or Disassociation frame unnecessarily. Add a new nl80211 attribute to allow this sending of the frame be skipped, but with all other deauth/disassoc operations being completed. Similar state change is also needed for IEEE 802.11r FT protocol in the FT-over-DS case which does not use Authentication frame exchange in a transition to another BSS. For this to work with cfg80211, an authentication entry needs to be created for the target BSS without sending out an Authentication frame. The nl80211 authentication command can be used for this purpose, too, with the new attribute to indicate that the command is only for changing local state. This enables wpa_supplicant to complete FT-over-DS transition successfully. Signed-off-by: Jouni Malinen <j@w1.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Kalle Valo authored
Better use the macro for consistency, the content is the same anyway. Signed-off-by: Kalle Valo <kvalo@adurom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Bruno Randolf authored
This is an Adaptive Noise Imunity (ANI) implementation for ath5k. I have looked at both ath9k and HAL sources (they are nearly the same), and even though i have implemented some things differently, the basic algorithm is practically the same, for now. I hope that this can serve as a clean start to improve the algorithm later. This also adds a possibility to manually control ANI settings, right now only thru a debugfs file: * set lowest sensitivity (=highest noise immunity): echo sens-low > /sys/kernel/debug/ath5k/phy0/ani * set highest sensitivity (=lowest noise immunity): echo sens-high > /sys/kernel/debug/ath5k/phy0/ani * automatically control immunity (default): echo ani-on > /sys/kernel/debug/ath5k/phy0/ani * to see the parameters in use and watch them change: cat /sys/kernel/debug/ath5k/phy0/ani Manually setting sensitivity will turn the automatic control off. You can also control each of the five immunity parameters (noise immunity, spur immunity, firstep, ofdm weak signal detection, cck weak signal detection) manually thru the debugfs file. This is tested on AR5414 and nearly doubles the thruput in a noisy 2GHz band. Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
- 06 Apr, 2010 14 commits
-
-
Rafał Miłecki authored
Reported-by: Myhailo Danylenko <isbear@ukrpost.net> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Juuso Oikarinen authored
This patch modifies tx-queue flushing to correspond with tx-path - i.e. also frames for which no ack was requested are forwarded to the mac80211 for disposal. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Juuso Oikarinen authored
Remove ERROR print from psm-entry-fail scenario, instead use an INFO print. Also, add INFO print to the beacon-loss scenario. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Juuso Oikarinen authored
Increase the fixed listen-interval max value configured to the mac80211 on driver init. This value will allow a larger value to be configured to the AP, which means the AP will buffer our frames longer. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Juuso Oikarinen authored
Configure meaningful rates to be used with the templates. For control frames, use the determined basic rates (currently the lowest rate for the band) and for data-frames (null-funcs) let the firmware use the current rate policy to determine the rate. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Juuso Oikarinen authored
Currently the mac80211 is not telling a hardware rate controlled driver a rate to use for association frames etc. So to be safe, use the lowest rate of each band for communication. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Juuso Oikarinen authored
The firmware does not like the host configuring the keep-alive after it has been once configured after a join-operation. Instead, it will complain about invalid parameters, which do not break functionality, but do not look nice in the syslog either. This patch prevents the complaints by only configuring the keep-alive once for an association, after the first time join is performed with the correct bssid. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Luciano Coelho authored
The command header was missing in the wl1271_cmd_disconnect structure. It was working fine by sheer luck, because the parameters are not critical and because our wl1271_cmd_send() function was overwriting the rx_config_options with the actual header. This patch adds the header to the command structure. Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Luciano Coelho authored
Our SPI driver is called "wl1271_spi" in the driver information structure. Let's use the same for SDIO so that things are aligned. Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
For USB devices, this check is invalid. Remove the check so that new product IDs can be added. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
This can be used to store the bus types ( AHB/PCI/USB ). Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
commits 8e6f5aa2 and db1a052b accidentally introduced compile errors that happens when ath9k debug is not enabled. This patch fixes the declaration of the inline stubs to resolve this. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Pavel Roskin authored
ah->mask_reg was used to hold different data throughout the driver. ath9k_hw_init_interrupt_masks() used it to save the value written to AR_IMR. ath9k_hw_set_interrupts() used it to hold the interrupt mask as defined in enum ath9k_int. Those masks differ in many bits. Use ah->imask instead of ah->mask_reg in ath9k_hw_set_interrupts() and ath9k_hw_updatetxtriglevel(). That's what the code was meant to do. ah->imask is initialized in ath9k_start(), so we don't need to initialize it from ah->mask_reg. Once it's done, ah->mask_reg becomes write-only, so it's replaced with a local variable in ath9k_hw_init_interrupt_masks(). Signed-off-by: Pavel Roskin <proski@gnu.org> Reported-by: Julia Lawall <julia@diku.dk> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-