- 22 Oct, 2010 40 commits
-
-
Matthias G. Eckermann authored
this patch to qcserial.c enables the Diagnostics Monitor and NMEA GPS ports on Qualcomm Gobi 2000 devices. A Gobi 2000 device will provide 3 serial ports: # /dev/ttyUSB0 -> Diagnostics # /dev/ttyUSB1 -> 3G Modem # /dev/ttyUSB2 -> NMEA GPS port * The Diagnostics Monitor uses Qualcomm's DM protocol; I used libqcdm (ModemManager) to talk to it, found it working, but at least DM commands 12 and 64 are not implemented on my device (Gobi 2000 built into Thinkpad x100e). * Functionality of the 3G Modem port remains unchanged. * The GPS port and how to enable it has been confirmed now in the Gobi 3000 source code at: https://www.codeaurora.org/patches/quic/gobi/ Enable/disable GPS via: echo "\$GPS_START" > /dev/ttyUSB2 # use GPS echo "\$GPS_STOP" > /dev/ttyUSB2 Signed-off-by:
Matthias G. Eckermann <mge@arcor.de>
-
Yauheni Kaliuta authored
In usb_cdc_ncm_dpe32 the fields are 32 bit long and according to usb style (hungarian notation) should be called dwDatagramIndex and dwDatagramLength (see CDC NCM subclass spec, 3.3.2). Actually, they were called wDatagramIndex, wDatagramLength. Signed-off-by:
Yauheni Kaliuta <yauheni.kaliuta@nokia.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Johan Hovold authored
This reverts commit 6a1a82df. RTS and DTR should not be modified based on CRTSCTS when calling set_termios. Modem control lines are raised at port open by the tty layer and should stay raised regardless of whether hardware flow control is enabled or not. This is in conformance with the way serial ports work today and many applications depend on this behaviour to be able to talk to hardware implementing hardware flow control (without the applications actually using it). Hardware which expects different behaviour on these lines can always use TIOCMSET/TIOCMBI[SC] after port open to change them. Reported-by:
Daniel Mack <daniel@caiaq.de> Reported-by:
Dave Mielke <dave@mielke.cc> Signed-off-by:
Johan Hovold <jhovold@gmail.com> Cc: stable <stable@kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Matthew Garrett authored
Seems to work fine in my testing. Signed-off-by:
Matthew Garrett <mjg@redhat.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Jean-Christophe PLAGNIOL-VILLARD authored
to ensure gpio_is_valid return false Signed-off-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by:
Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: stable <stable@kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Yauheni Kaliuta authored
Make a dedicated structure for datagram pointer entry. There is no explicit declaration in the spec, but it's used by the host implementation and makes the structure more clear. Add some missed constants from the spec Signed-off-by:
Yauheni Kaliuta <yauheni.kaliuta@nokia.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Yauheni Kaliuta authored
This reverts commit 65e0b499. Since the host and gadget implementations are different, there is no common code for the file, remove for now. Signed-off-by:
Yauheni Kaliuta <yauheni.kaliuta@nokia.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Yauheni Kaliuta authored
Some typos were in the initial commit, make the spelling according to the spec. Add some more comments. Also change constant names according to the style of the rest of the file Signed-off-by:
Yauheni Kaliuta <yauheni.kaliuta@nokia.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Enrico Mioso authored
This patch, adds to the option driver the Onda Communication (http://www.ondacommunication.com) vendor id, and the MT825UP modem device id. Note that many variants of this same device are being release here in Italy (at least one or two per telephony operator). These devices are perfectly equivalent except for some predefined settings (which can be changed of course). It should be noted that most ONDA devices are allready supported (they used other vendor's ids in the past). The patch seems working fine here, and the rest of the driver seems uninfluenced. Signed-off-by:
Enrico Mioso <mrkiko.rs@gmail.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
DJ Delorie authored
RX610 development board by Renesas Bus 001 Device 024: ID 045b:0053 Hitachi, Ltd Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x045b Hitachi, Ltd idProduct 0x0053 bcdDevice 1.00 iManufacturer 1 Silicon Labs iProduct 2 RX-Stick iSerial 3 0001 . . . http://am.renesas.com/rx610stickSigned-off-by:
DJ Delorie <dj@delorie.com> Cc: stable <stable@kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Keshava Munegowda authored
The un-registration of OHCI driver was not done in the ohci_hcd_mod_exit function. This was affecting rmmod command not to work for OMAP3 platforms. The platform driver un-registration for OMAP3 platforms is perfomed while removing the OHCI module from kernel. Signed-off-by:
Keshava Munegowda <keshava_mgowda@ti.com> Signed-of-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Rich Mattes authored
Adds support for Accesio USB to Serial adapters, which are built around FTDI FT232 UARTs. Tested with the Accesio USB-COM-4SM. Signed-off-by:
Rich Mattes <richmattes@gmail.com> Cc: stable <stable@kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Joe Perches authored
Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Alan Stern authored
The /sys/kernel/debug/usb/devices file doesn't know about Wireless or SuperSpeed USB. This patch (as1416b) teaches it, and updates the Documentation/usb/proc_sub_info.txt file accordingly. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> CC: David Vrabel <david.vrabel@csr.com> CC: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Andy Shevchenko authored
Signed-off-by:
Andy Shevchenko <andy.shevchenko@gmail.com> Cc: David Vrabel <david.vrabel@csr.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Mauro Carvalho Chehab authored
There are lots of ZTE USB id's currently not covered by usb/serial. Adds them, to allow those devices to work properly on Linux. While here, put the USB ID's for 0x2002/0x2003 at the sorted order. This patch is based on zte.c file found on MF645. PS.: The ZTE driver is commenting the USB ID for 0x0053. It also adds, commented, an USB ID for 0x0026. Not sure why, but I think that 0053 is used by their devices in storage mode only. So, I opted to keep the comment on this patch. Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com> Cc: stable <stable@kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Joe Perches authored
Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Javier Martinez Canillas authored
In today linux-next I got a compile error on usb/host/isp1362-hcd: drivers/usb/host/isp1362-hcd.c: In function ‘isp1362_hub_control’: drivers/usb/host/isp1362-hcd.c:1680: error: ‘ohci’ undeclared (first use in this function) The problem is when the CONFIG_USB_OTG option is enabled. ohci variable is never declared and there isn't any CONFIG_USB_OTG dependent code besides the portion defined in isp1362_hub_control. So I think that maybe USB OTG support is not needed/supported. This patch removes the CONFIG_USB_OTG dependent block so the driver can compile cleanly. Signed-off-by:
Javier Martinez Canillas <martinez.javier@gmail.com> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Lothar Wassmann <LW@KARO-electronics.de> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Roger Quadros authored
The composite gadget will OOPS if the host sends a control request targetted to an interface of an un-configured composite device. This patch prevents this. The OOPS was observed during WHQL USB CV tests. With this patch, the device STALLs as per requirement. Failing test case: From host do the following. I used libusb-1.0 1) Set configuration to zero. libusb_control_transfer(device_handle, 0, /* standard OUT */ 0x9, /* setConfiguration */ 0, 0, NULL, 0, 0); 2) Query current configuratioan. libusb_control_transfer(device_handle, 0x80, /* standard IN*/ 0x8, /* getConfiguration */ 0, 0, data, 1, 0); 3) Send the non-standard ctrl transfer targetted to interface libusb_control_transfer(device_handle, 0x81, /* standard IN to interface*/ 0x6, /* getDescriptor */ 0x2300, 0, data, 0x12, 0); Signed-off-by:
Roger Quadros <roger.quadros@nokia.com> Cc: stable <stable@kernel.org> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Michal Nazarewicz <m.nazarewicz@samsung.com> Cc: Robert Lukassen <robert.lukassen@tomtom.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Alan Stern authored
This patch (as1417) fixes a problem affecting some (or all) nVidia chipsets. When the computer is shut down, the OHCI controllers continue to power the USB buses and evidently they drive a Reset signal out all their ports. This prevents attached devices from going to low power. Mouse LEDs stay on, for example, which is disconcerting for users and a drain on laptop batteries. The fix involves leaving each OHCI controller in the OPERATIONAL state during system shutdown rather than putting it in the RESET state. Although this nominally means the controller is running, in fact it's not doing very much since all the schedules are all disabled. However there is ongoing DMA to the Host Controller Communications Area, so the patch also disables the bus-master capability of all PCI USB controllers after the shutdown routine runs. The fix is applied only to nVidia-based PCI OHCI controllers, so it shouldn't cause problems on systems using other hardware. As an added safety measure, in case the kernel encounters one of these running controllers during boot, the patch changes quirk_usb_handoff_ohci() (which runs early on during PCI discovery) to reset the controller before anything bad can happen. Reported-by:
Pali Rohár <pali.rohar@gmail.com> Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> CC: David Brownell <david-b@pacbell.net> Tested-by:
Pali Rohár <pali.rohar@gmail.com> CC: stable <stable@kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Dan Carpenter authored
This ioremap() was leaked on an error path. Signed-off-by:
Dan Carpenter <error27@gmail.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Praveena Nadahally authored
The protocol code is set 00 in IAD and it's set to 01 in ACM control interface descriptor in f_acm.c file. Due to this, windows is unable to install the modem(ACM) driver based on class-subclass-protocol matching. This patch corrects the protocol code in ACM IAD to the same as in acm_control_interface_desc protocol code. Acked-by:
Linus Walleij <linus.walleij@stericsson.com> Signed-off-by:
Praveena Nadahally <praveen.nadahally@stericsson.com> Cc: stable <stable@kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Javier Martinez Canillas authored
In today linux-next I got a compile warning due a possible uninitialized variable This patch solves the issue initializing the variable Signed-off-by:
Javier Martinez Canillas <martinez.javier@gmail.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Magnus Damm <damm@opensource.se> Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Hao Wu authored
This patch updated Kconfig for langwell otg transceiver driver. Add ipc driver(INTEL_SCU_IPC) as a dependency. Driver version is updated too. Signed-off-by:
Hao Wu <hao.wu@intel.com> Signed-off-by:
Alan Cox <alan@linux.intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Hao Wu authored
This patch adds one new header file for the common data structure used in Intel Penwell/Langwell MID Platform OTG Transceiver drivers. After switched to the common data structure, Langwell/Penwell OTG Transceiver driver will provide an unified interface to host/client driver. Reported-by:
Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by:
Hao Wu <hao.wu@intel.com> Signed-off-by:
Alan Cox <alan@linux.intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Thomas Gleixner authored
The "mutex" ftdi->sw_lock is used as a lock and a completion. Convert it to a real semaphore which allows both. Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Mihai Donțu authored
Corrected the coding style. Signed-off-by:
Mihai Dontu <mihai.dontu@gmail.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Matthieu CASTET authored
tdi_reset is already taking care of setting host mode for tdi devices. Don't duplicate code in platform driver. Make ehci_halt a nop if the controller is not in host mode (otherwise it will fail), and let's ehci_reset do the tdi_reset. We need to move hcd->has_tt flags before ehci_halt, in order ehci_halt knows we are a tdi device. Before the setup routine was doing : - put controller in host mode - ehci_halt - ehci_init - hcd->has_tt = 1; - ehci_reset Now we do : - hcd->has_tt = 1; - ehci_halt - ehci_init - ehci_reset PS : now we handle correctly the device -> host transition. Signed-off-by:
Matthieu CASTET <matthieu.castet@parrot.com> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Michael Prokop authored
It's spelled "Function Filesystem" / "FunctionFS". This patch fixes some typos (FunctioFS->FunctionFS, Funcion->Function, funcion->function, redundant "as") in the Kconfig description of USB_FUNCTIONFS*. Signed-off-by:
Michael Prokop <mika@grml.org> Acked-by:
Michal Nazarewicz <m.nazarewicz@samsung.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Alan Stern authored
This patch (as1413) changes g_file_storage to avoid generating a bogus automatic serial-number string descriptor. If the user doesn't provide a valid serial number via a module parameter then a warning is logged and the gadget won't have any serial string descriptor at all. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Acked-by:
David Brownell <david-b@pacbell.net> CC: Michal Nazarewicz <m.nazarewicz@samsung.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Joe Perches authored
There are about 2500 void functions in drivers/usb Only a few used return; at end of function. Standardize them a bit. Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Simon Arlott authored
Commit f661c6f8 adds a check of the pipe type if CONFIG_USB_DEBUG is enabled, but it doesn't output anything if this scenario occurs. Signed-off-by:
Simon Arlott <simon@fire.lp0.eu> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Julia Lawall authored
The same expression is tested twice and the result is the same each time. Instead test for use_dma_ppb as in the test above. The sematic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @expression@ expression E; @@ ( * E || ... || E | * E && ... && E ) // </smpl> Signed-off-by:
Julia Lawall <julia@diku.dk> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Michal Nazarewicz authored
The __ref* tags may have been confusing for new kernel developers (I was confused by them for sure) so adding a few more sentences to comment to clear things up for people who see those for the first time. Signed-off-by:
Michal Nazarewicz <m.nazarewicz@samsung.com> Acked-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by:
Sam Ravnborg <sam@ravnborg.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Uwe Kleine-König authored
The bind function is most of the time only called at init time so there is no need to save a pointer to it in the configuration structure. This fixes many section mismatches reported by modpost. Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> [m.nazarewicz@samsung.com: updated for -next] Signed-off-by:
Michał Nazarewicz <m.nazarewicz@samsung.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Michal Nazarewicz authored
The bind function is most of the time only called at init time so there is no need to save a pointer to it in the composite driver structure. This fixes many section mismatches reported by modpost. Signed-off-by:
Michał Nazarewicz <m.nazarewicz@samsung.com> Acked-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Uwe Kleine-König authored
To accomplish this the function to register a gadget driver takes the bind function as a second argument. To make things clearer rename the function to resemble platform_driver_probe. This fixes many section mismatches like WARNING: drivers/usb/gadget/g_printer.o(.data+0xc): Section mismatch in reference from the variable printer_driver to the function .init.text:printer_bind() The variable printer_driver references the function __init printer_bind() All callers are fixed. Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> [m.nazarewicz@samsung.com: added dbgp] Signed-off-by:
Michał Nazarewicz <m.nazarewicz@samsung.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Michal Nazarewicz authored
This reverts a commit which proposed an invalid solution for a section mismatch. Next 3 commits will fix it correctly. Conflicts: drivers/usb/gadget/mass_storage.c Signed-off-by:
Michal Nazarewicz <m.nazarewicz@samsung.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Michal Nazarewicz authored
This patch removes some of the string registration from the Multifunction Composite Gadget as composite layer can handle the iManufacturer and iProduct for us. This also adds the "needs_serial" so that composite layer will issue a warning if user space fails to provide the iSerialNumber module parameter. Signed-off-by:
Michal Nazarewicz <m.nazarewicz@samsung.com> Signed-off-by:
Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Michal Nazarewicz authored
This patch removes string registration from the Mass Storage Gadget. With recent changes to the composite framework, all that we need is handled by the composite layer. This means composite registers a string ID for manufacturer and product. This also adds the "needs_serial" so that composite layer will issue a warning if user space fails to provide the iSerialNumber module parameter. Signed-off-by:
Michal Nazarewicz <m.nazarewicz@samsung.com> Signed-off-by:
Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-