In hclge_dcb.c, these pair of codes:
	hclge_notify_client(hdev, HNAE3_DOWN_CLIENT);
	hclge_notify_client(hdev, HNAE3_UNINIT_CLIENT);
and
	hclge_notify_client(hdev, HNAE3_INIT_CLIENT);
	hclge_notify_client(hdev, HNAE3_UP_CLIENT);
are called many times, so make them into a function.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To better identify abnormal conditions, this patch modifies or
adds some logs to show driver status more accurately.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Zhongzhu Liu <liuzhongzhu@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch simplifies parameters of some functions by deleting
unused parameter.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch replaces kstrtouint()'s patameter base with 0 in the
hclge_dbg_dump_tm_mac(), which makes it more flexible. Also
uses a macro to replace string "dump tm map", since it has been
used multiple times.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch uses macro to replace some magic number.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For making the code more readable, this patch uses a array to
keep the information about the dumping register, and then uses
it to parse the parameter cmd_buf which passing into
hclge_dbg_dump_reg_cmd().

Also replaces parameter "base" of kstrtouint with 0 in the
hclge_dbg_dump_reg_common(), which makes it more flexible.
Signed-off-by: Zhongzhu Liu <liuzhongzhu@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Starting with firmware version MC10.18.0, we have support for
L2 flow control. Asymmetrical configuration (Rx or Tx only) is
supported, but not pause frame autonegotioation.

Pause frame configuration is done via ethtool. By default, we start
with flow control enabled on both Rx and Tx. Changes are propagated
to hardware through firmware commands, using two flags (PAUSE,
ASYM_PAUSE) to specify Rx and Tx pause configuration, as follows:

PAUSE | ASYM_PAUSE | Rx pause | Tx pause
----------------------------------------
  0   |     0      | disabled | disabled
  0   |     1      | disabled | enabled
  1   |     0      | enabled  | enabled
  1   |     1      | enabled  | disabled

The hardware can automatically send pause frames when the number
of buffers in the pool goes below a predefined threshold. Due to
this, flow control is incompatible with Rx frame queue taildrop
(both mechanisms target the case when processing of ingress
frames can't keep up with the Rx rate; for large frames, the number
of buffers in the pool may never get low enough to trigger pause
frames as long as taildrop is enabled). So we set pause frame
generation and Rx FQ taildrop as mutually exclusive.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Whenever a link state change occurs, we get notified and save
the new link settings in the device's private data. In ethtool
get_link_ksettings, use the stored state instead of interrogating
the firmware each time.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

We only support fixed-link for now, so there is no point in
offering users the option to change link settings via ethtool.

Functionally there is no change, since firmware prevents us from
changing link parameters anyway.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Various updates

Patch #1 from Amit removes 56G speed support. The reasons for this are
detailed in the commit message.

Patch #2 from Shalom ensures that the hardware does not auto negotiate
the number of used lanes. For example, if a four lane port supports 100G
over both two and four lanes, it will not advertise the two lane link
mode.

Patch #3 bumps the firmware version supported by the driver.

Patch #4 from Petr adds ethtool counters to help debug the internal PTP
implementation in mlxsw. I copied Richard on this patch in case he has
comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

On Spectrum-1, timestamped PTP packets and the corresponding timestamps need to
be kept in caches until both are available, at which point they are matched up
and packets forwarded as appropriate. However, not all packets will ever see
their timestamp, and not all timestamps will ever see their packet. It is
necessary to dispose of such abandoned entries, so a garbage collector was
introduced in commit 5d23e415 ("mlxsw: spectrum: PTP: Garbage-collect
unmatched entries").

If these GC events happen often, it is a sign of a problem. However because this
whole mechanism is taking place behind the scenes, there is no direct way to
determine whether garbage collection took place.

Therefore to fix this, on Spectrum-1 only, expose four artificial ethtool
counters for the GC events: GCd timestamps and packets, in TX and RX directions.

Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The new version supports extended error reporting from firmware via a
new TLV in the EMAD packet. Similar to netlink extended ack.

It also fixes an issue in the PCI code that can result in false AER
errors under high Tx rate.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After 50G-1-lane and 100G-2-lanes link modes were introduced, the driver
is facing situations in which the hardware auto negotiates not only on
speed and type, but also on number of lanes.

Prevent auto negotiation on number of lanes by allowing only port speeds
that can be supported on a given port according to its width.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 275e928f ("mlxsw: spectrum: Prevent force of 56G") prevented
the driver from setting a speed of 56G when auto-negotiation is off.
This is the only speed supported by mlxsw that cannot be set when
auto-negotiation is off, which makes it difficult to write generic
tests.

Further, the speed is not supported by newer ASICs such as Spectrum-2
and to the best of our knowledge it is not used by current users.

Therefore, remove 56G support from mlxsw.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some ethernet drivers may call phy_start() and phy_stop() from
ndo_open() and ndo_close() respectively.

When network cable is unconnected, and operate like below:
step 1: ifconfig ethX up -> ndo_open -> phy_start ->start
autoneg, and phy is no link.
step 2: ifconfig ethX down -> ndo_close -> phy_stop -> just stop
phy state machine.

This patch forces phy suspend even phydev->link is off.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
100GbE Intel Wired LAN Driver Updates 2019-08-26

This series contains updates to ice driver only.

Usha fixes the statistics reported on 4 port NICs which were reporting
the incorrect statistics due to using the incorrect port identifier.

Victor fixes an issue when trying to traverse to the first node of a
requested layer by adding a sibling head pointer for each layer per
traffic class.

Anirudh cleans up the locking and logic for enabling and disabling
VSI's to make it more consistent.  Updates the driver to do dynamic
allocation of queue management bitmaps and arrays, rather than
statically allocating them which consumes more memory than required.
Refactor the logic in ice_ena_msix_range() for clarity and add
additional checks for when requested resources exceed what is available.

Jesse updates the debugging print statements to make it more useful when
dealing with link and PHY related issues.

Krzysztof adds a local variable to the VSI rebuild path to improve
readability.

Akeem limits the reporting of MDD events from VFs so that the kernel
log is not clogged up with MDD events which are duplicate or potentially
false positives.  Fixed a reset issue that would result in the system
getting into a state that could only be resolved by a reboot by
testing if the VF is in a disabled state during a reset.

Michal adds a check to avoid trying to access memory that has not be
allocated by checking the number of queue pairs.

Jake fixes a static analysis warning due to a cast of a u8 to unsigned
long, so just update ice_is_tc_ena() to take a unsigned long so that a
cast is not necessary.

Colin Ian King fixes a potential infinite loop where a u8 is being
compared to an int.

Maciej refactors the queue handling functions that work on queue arrays
so that the logic can be done for a single queue.

Paul adds support for VFs to enable and disable single queues.

Henry fixed the order of operations in ice_remove() which was trying to
use adminq operations that were already disabled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Variable result is being assigned a value that is never read and result
is being re-assigned a little later on. The assignment is redundant
and hence can be removed.

Addresses-Coverity: ("Ununsed value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove two holes on 64bit arches, to bring the size
to one cache line exactly.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Voon Weifeng says:

====================
stmmac: Add EHL and TGL PCI info and PCI ID

In order to keep PCI info simple and neat, this patch series have
introduced a 3 hierarchy of struct. First layer will be the
intel_mgbe_common_data struct which keeps all Intel common configuration.
Second layer will be xxx_common_data which keeps all the different Intel
microarchitecture, e.g tgl, ehl. The third layer will be configuration
that tied to the PCI ID only based on speed and RGMII/SGMII interface.

EHL and TGL will also having a higher system clock which is 200Mhz.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

EHL DW EQOS is running on a 200MHz clock. Setting up stmmac-clk,
ptp clock and ptp_max_adj to 200MHz.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added EHL RGMII 1Gbps PCI ID. Different MII and speed will have
different PCI ID.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added TGL SGMII 1Gbps PCI ID. Different MII and speed will have
different PCI ID.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added EHL SGMII 1Gbps PCI ID. Different MII and speed will have
different PCI ID.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marek Behún says:

====================
net: dsa: mv88e6xxx: Peridot/Topaz SERDES changes

this is the fifth version of changes for the Topaz/Peridot family of
switches. The patches apply on net-next.
Changes since v4:
 - added Reviewed-by and Tested-by tags on first 2 patches, the others
   are changed are affected by changes in patch 3/6, so I did not add
   the tags, except for 5/6, which is just macro renaming
 - patch 3 was changed: the serdes_get_lane returns 0 on success (lane
   was discovered), -ENODEV if not lane is present on the port, and
   other error if other error occured. Lane is put into a pointer of
   type u8
 - patches 4 and 6 were affected by this (error detecting from
   serdes_get_lane)
 - Andrew's complaint about the two additional parameters
   (allow_over_2500 and make_cmode_writable) was addressed, by Vivien's
   advice: I put a new method into chip operations structure, named
   port_set_cmode_writable. This is called from mv88e6xxx_port_setup_mac
   just before port_set_cmode. The method is implemented for Topaz.
   The check if cmodes over 2500 should be allowed on given port is now
   done in the specific port_set_cmode() that requires it, thus the
   allow_over_2500 argument is not needed

Again, tested on Turris Mox with Peridot, Topaz, and Peridot + Topaz.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently we support SERDES on the Topaz family in a limited way: no
IRQs and the cmode is not writable, thus the mode is determined by
strapping pins.

Marvell's examples though show how to make cmode writable on port 5 and
support SGMII autonegotiation. It is done by writing hidden registers,
for which we already have code.

This patch adds support for making the cmode for the SERDES port
writable on the Topaz family, via a new chip operation,
.port_set_cmode_writable, which is called from mv88e6xxx_port_setup_mac
just before .port_set_cmode.

SERDES IRQs are also enabled for Topaz.

Tested on Turris Mox.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a cosmetic update. We are removing the last underscore from
macros MV88E6XXX_PORT_STS_CMODE_100BASE_X and
MV88E6XXX_PORT_STS_CMODE_1000BASE_X. The 2500base-x version does not
have that underscore. Also PHY_INTERFACE_MODE_ macros do not have it
there.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

By adding an additional serdes_get_lane implementation (for Topaz), we
can merge the implementations of other SERDES functions (powering and
IRQs). We can skip checking port numbers, since the serdes_get_lane()
methods inform if there is no lane on a port or if the lane cannot be
used for given cmode.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Create a serdes_get_lane() method in the mv88e6xxx operations structure.
Use it instead of calling the different implementations.
Also change the methods so that their return value is used only for
error. The lane number is put into a place referred to by a pointer
given as argument. If the port does not have a lane, return -ENODEV.
Lanes are phy addresses, so use u8 as their type.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch moves the functions operating on the hidden debug registers
into it's own file, port_hidden.c. The functions prefix is renamed from
mv88e6390_hidden_ to mv88e6xxx_port_hidden_, to be consistent with the
rest of this driver. The macros are prefixed with MV88E6XXX_ prefix, and
are changed not to use the BIT() macro nor bit shifts, since the rest of
the port.h file does not use it.

We also add the support for setting the Block Address field when
operating hidden registers. Marvell's mdio examples for SERDES settings
on Topaz use Block Address 0x7 when reading/writing hidden registers,
and although the specification says that block must be set to 0xf, those
settings are reachable only with Block Address 0x7.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mv88e6390_serdes_irq_link_sgmii IRQ handler reads the SERDES PHY
status register to determine speed, among other things. If cmode of the
port is set to 2500base-x, though, the PHY still reports 1000 Mbps (the
PHY register itself does not differentiate between 1000 Mbps and 2500
Mbps - it thinks it is running at 1000 Mbps, although clock is 2.5x
faster).
Look at the cmode and set SPEED_2500 if cmode is set to 2500base-x.
Also tell mv88e6xxx_port_setup_mac the PHY interface mode corresponding
to current cmode in terms of phy_interface_t.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Xin Long says:

====================
sctp: add SCTP_ECN_SUPPORTED sockopt

This patchset is to make ecn flag per netns and endpoint and then
add SCTP_ECN_SUPPORTED sockopt, as does for other feature flags.
====================
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SCTP_ECN_SUPPORTED sockopt will be added to allow users to change
ep ecn flag, and it's similar with other feature flags.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sysctl net.sctp.ecn_enable is added in this patch. It will allow
users to change the default sctp ecn flag, net.sctp.ecn_enable.

This feature was also required on this thread:

  http://lkml.iu.edu/hypermail/linux/kernel/0812.1/01858.htmlSigned-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to add ecn flag for both netns_sctp and sctp_endpoint,
net->sctp.ecn_enable is set 1 by default, and ep->ecn_enable will
be initialized with net->sctp.ecn_enable.

asoc->peer.ecn_capable will be set during negotiation only when
ep->ecn_enable is set on both sides.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/mediatek/mtk_eth_soc.c: In function mtk_handle_irq:
drivers/net/ethernet/mediatek/mtk_eth_soc.c:1951:6: warning: variable status set but not used [-Wunused-but-set-variable]

Fixes: 296c9120 ("net: ethernet: mediatek: Add MT7628/88 SoC support")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>