- 10 Oct, 2007 40 commits
-
-
Michael Buesch authored
The remaining warning in phy.c will be fixed later. Signed-off-by:
Michael Buesch <mb@bu3sch.de> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Al Viro authored
Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
Jeff Garzik <jeff@garzik.org>
-
Al Viro authored
Signed-off-by:
-
Al Viro authored
Signed-off-by:
-
Al Viro authored
Signed-off-by:
-
Al Viro authored
Signed-off-by:
-
Al Viro authored
Signed-off-by:
-
Al Viro authored
Signed-off-by:
-
Al Viro authored
Note: we still have several fishy areas - mcast filter and vlan handling. Signed-off-by:
-
Al Viro authored
Signed-off-by:
-
Al Viro authored
Signed-off-by:
-
Al Viro authored
Signed-off-by:
-
Al Viro authored
Signed-off-by:
-
Al Viro authored
Signed-off-by:
-
Al Viro authored
Signed-off-by:
-
Al Viro authored
amd8111e_calc_coalesce() ends up with insane values of tx_data_rate since ->tx_bytes increments missing conversion from little- to host-endian Signed-off-by:
-
Al Viro authored
Signed-off-by:
-
Al Viro authored
Signed-off-by:
-
Al Viro authored
Layout of opts2 is : MSB(vlan_tag) : LSB(vlan_tag) : flags : 0 : regardless of the host endianness. On little-endian the current code ends up with the right values, but on big-endian it blows. In r8169.c the same bug had been fixed in commit d35da12a (r8169: endianness fixes). Signed-off-by:
-
Al Viro authored
Signed-off-by:
-
Ursula Braun authored
maintainer change for s390 networking Signed-off-by:
Ursula Braun <braunu@de.ibm.com> Signed-off-by:
-
Vitaly Bordug authored
Signed-off-by:
Vitaly Bordug <vitb@kernel.crashing.org> Signed-off-by:
-
Vitaly Bordug authored
Signed-off-by:
-
Maciej W. Rozycki authored
Rename NET_SB1250_MAC to SB1250_MAC to follow the convention. Signed-off-by:
Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by:
-
Maciej W. Rozycki authored
The SB1250 network interfaces are Gigabit Ethernet ones. Move the Kconfig entry to the appropriate section and add some help text. Signed-off-by:
-
Dhananjay Phadke authored
Resubmitting the patch. This patch improves ethtool support for printing correct ring statistics, segmentation offload status, etc. Signed-off by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: -
David Gibson authored
Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by:
David Gibson <david@gibson.dropbear.id.au> Signed-off-by:
-
Al Viro authored
Signed-off-by:
-
Bryan Wu authored
Since we are adding requirement for the PHYLIB for this driver, there should be a select for that Cc: Robin Getz <robin.getz@analog.com> Signed-off-by:
Bryan Wu <bryan.wu@analog.com> Signed-off-by:
-
Bryan Wu authored
- add MDIO functions and register mdio bus - add phy abstraction layer (PAL) functions and use PAL API - test on STAMP537 board Signed-off-by:
-
Bryan Wu authored
Blackfin EMAC driver: add power management interface and change the bf537mac_reset to bf537mac_disable Signed-off-by:
-
Alex Landau authored
Alex Landau writes in the forums: Previously, changing the MAC address (e.g. via ifconfig) resulted in a generic function to be called that only changed a variable in memory. This patch also updated the Blackfin MAC address registers to filter the correct new MAC. Signed-off-by:
Alex Landau <lirsb@yahoo.com> Signed-off-by:
Mike Frysinger <michael.frysinger@analog.com> Signed-off-by:
-
Sivakumar Subramani authored
- Update transceiver information in ethtool function Signed-off-by:
Sreenivasa Honnur <sreenivasa.honnur@neterion.com> Signed-off-by:
-
Sivakumar Subramani authored
- Added set_mac_address driver entry point - Copying permanent mac address to dev->perm_addr - Incorporated following review comments from Jeff - Converted the macro to a function and removed call to memset - regarding function naming convention, for all callbacks and entry points will have 's2io_' prefix and helper functions will have 'do_s2io_' prefix. Signed-off-by: -
Sivakumar Subramani authored
Removed bimodal interrupt support - unused feature Signed-off-by:
Sivakumar Subramani <sivakumar.subramani@neterion.com> Signed-off-by:
Ramkrishna Vepa <ram.vepa@neterion.com> Signed-off-by:
-
Sivakumar Subramani authored
- Changed kmalloc+memset to k[zc]alloc as per Mariusz's patch <m.kozlowski@tuxland.pl> Signed-off-by:
-
Jeff Garzik authored
These have been superceded by the new ->get_sset_count() hook. Signed-off-by:
-
Michael Buesch authored
Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Michael Wu authored
Signed-off-by:
Michael Wu <flamingice@sourmilk.net> Signed-off-by:
-
Joe Perches authored
This is nicer than the MAC_FMT stuff. Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
-
