- 23 Apr, 2019 14 commits
-
-
Archit Taneja authored
The APQ8096 DB820c platform provides HDMI output. The MDSS block on 8x96 supports a direct HDMI out. Populate the MDSS, MDP and HDMI DT nodes. Also, add the HDMI HPD and DDC pinctrl nodes with the bias and driver strength specified for this platform. Signed-off-by:
Archit Taneja <architt@codeaurora.org> Signed-off-by:
Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by:
Andy Gross <agross@kernel.org>
-
Jordan Crouse authored
Add an initial node for the Adreno GPU. Signed-off-by:
Vivek Gautam <vivek.gautam@codeaurora.org> Signed-off-by:
Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by:
-
Archit Taneja authored
Signed-off-by:
-
Archit Taneja authored
Add device node for display smmu, aka. mdp_smmu. Signed-off-by:
-
Jordan Crouse authored
Add device node for graphics smmu, aka. adreno_smmu. Signed-off-by:
-
Matthias Kaehlcke authored
Specify the relative CPU capacity of all SDM845 AP cores. The values were provided by Qualcomm engineers. Signed-off-by:
Matthias Kaehlcke <mka@chromium.org> Reviewed-by:
Rajendra Nayak <rnayak@codeaurora.org> Signed-off-by:
-
Matthias Kaehlcke authored
The 8 CPU cores of the SDM845 are organized in two clusters of 4 big ("gold") and 4 little ("silver") cores. Add a cpu-map node to the DT that describes this topology. Signed-off-by:Douglas Anderson <dianders@chromium.org> Signed-off-by:
-
Matthias Kaehlcke authored
Add 'bi_tcxo' as ref clock for the DSI PHYs, it was previously hardcoded in the PLL 'driver' for the 10nm PHY. Signed-off-by:
Stephen Boyd <swboyd@chromium.org> Signed-off-by:
-
Matthias Kaehlcke authored
Add 'xo_board' as ref clock for the DSI PHYs, it was previously hardcoded in the PLL 'driver' for the 28nm PHY. Signed-off-by:
-
Matthias Kaehlcke authored
The temperature information from the temp-alarm block itself is very coarse ("temperature is above/below trip points"). Provide the driver with the die temperature channel of the ADC on the PMIC for more precise readings. Signed-off-by: -
Bjorn Andersson authored
Add the Audio DSP (ADSP) and Compute DSP (CDSP) nodes for TrustZone based remoteproc, supporting booting these cores on e.g. the MTP, and enable the same for the MTP. Tested-by:
Sibi Sankar <sibis@codeaurora.org> Reviewed-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by:
-
Bjorn Andersson authored
Define the rmtfs memory node. As the memory region specified in version 10 of the memory map is only 1MB a chunk of unallocated memory is chosen. Tested-by:
-
Bjorn Andersson authored
Update existing and add missing regions to the reserved memory map, as described in version 10. Reviewed-by:
-
Evan Green authored
Wire up the reset controller in the Qcom UFS controller for the PHY. This will be used to toggle PHY reset during initialization of the PHY. Reviewed-by:
Evan Green <evgreen@chromium.org> Signed-off-by:
-
- 19 Apr, 2019 6 commits
-
-
Marc Gonzalez authored
blsp1_i2c1 is at 0x0c175000 blsp2_i2c5 is at 0x0c1ba000 (the label is correct) Fixes: 1e71d0c2 ("arm64: dts: qcom: msm8998: Enumerate i2c controllers") Signed-off-by:
Marc Gonzalez <marc.w.gonzalez@free.fr> Reviewed-by:
Jeffrey Hugo <jhugo@codeaurora.org> Signed-off-by:
-
Khasim Syed Mohammed authored
The compatible flag should be different for each board to match with the dtb and to let the bootloader pick the appropriate dtb. Signed-off-by:
Khasim Syed Mohammed <khasim.mohammed@linaro.org> Signed-off-by:
Niklas Cassel <niklas.cassel@linaro.org> Signed-off-by:
-
Brian Masney authored
This adds the gpio-ranges property so that the GPIO pins are initialized by the GPIO framework and not pinctrl. This fixes a circular dependency between these two frameworks so GPIO hogging can be used on this board. This was not tested on this particular hardware, however this same change was tested on qcom-pm8941 using a LG Nexus 5 (hammerhead) phone. Signed-off-by:
Brian Masney <masneyb@onstation.org> Signed-off-by:
-
Brian Masney authored
This adds the gpio-ranges property so that the GPIO pins are initialized by the GPIO framework and not pinctrl. This fixes a circular dependency between these two frameworks so GPIO hogging can be used on this board. This was not tested on this particular hardware, however this same change was tested on qcom-pm8941 using a LG Nexus 5 (hammerhead) phone. Signed-off-by:
-
Brian Masney authored
This adds the gpio-ranges property so that the GPIO pins are initialized by the GPIO framework and not pinctrl. This fixes a circular dependency between these two frameworks so GPIO hogging can be used on this board. This was not tested on this particular hardware, however this same change was tested on qcom-pm8941 using a LG Nexus 5 (hammerhead) phone. Signed-off-by:
-
Brian Masney authored
This adds the gpio-ranges property so that the GPIO pins are initialized by the GPIO framework and not pinctrl. This fixes a circular dependency between these two frameworks so GPIO hogging can be used on this board. This was not tested on this particular hardware, however this same change was tested on qcom-pm8941 using a LG Nexus 5 (hammerhead) phone. Signed-off-by:
-
- 10 Apr, 2019 15 commits
-
-
Marc Gonzalez authored
Fixup MSM8998 UFS DT nodes now that Evan's reset series has landed. https://lore.kernel.org/lkml/20190321171800.104681-1-evgreen@chromium.org/Signed-off-by:
-
Andy Gross authored
-
Amit Kucheria authored
We don't have any cooling-devices related to the camera. Use the "hot" trip type so allow the temperature to be exported to userspace and remove the "critical" trip. Signed-off-by:
Amit Kucheria <amit.kucheria@linaro.org> Signed-off-by:
-
Amit Kucheria authored
Maintain naming consistency with what was landed for sdm845. Simplifies parsing for test tools. Signed-off-by:
-
Amit Kucheria authored
Maintain naming consistency with what was landed for sdm845. Simplifies parsing for test tools. Signed-off-by:
-
Amit Kucheria authored
Maintain naming consistency with what was landed for sdm845. Simplifies parsing for test tools. Signed-off-by:
-
Amit Kucheria authored
sdm845 has a total of 21 temperature sensors. Populate DT with information about them. Signed-off-by:
-
Amit Kucheria authored
msm8998 has a total of 22 temperature sensors. Populate DT with information about them. Signed-off-by:
-
Amit Kucheria authored
The first sensor is on top and the second sensor below the GPU Signed-off-by:
-
Amit Kucheria authored
The GPU sensor is sensor ID 13 on controller 0 Fixes: 4449b6f2 ("arm64: dts: qcom: msm8998: Add tsens and thermal-zones") Signed-off-by:
-
Amit Kucheria authored
The silver cluster (typically cpu0-3) are monitored by sensor IDs 1-3 on tsens controller 0. The gold cluster (typically cpu4-7) are monitored by sensor IDs 7-10 on tsens controller 0. Fixes: 4449b6f2 ("arm64: dts: qcom: msm8998: Add tsens and thermal-zones") Signed-off-by:
-
Amit Kucheria authored
msm8996 has a total of 21 temperature sensors. Populate DT with information about them. There are 2 sensors on each of the cpus - one on the top, the other below (we only expose one on the top in DT for now). For the GPU, we expose both, the one on the top and the one below. Depending on the version of the silicon, sensor 2 is either placed near the L3 cache or the venus video decoder. It would've been nice to be able to be version-specific but we don't have DTs that differentiate the two versions of silicon yet. Signed-off-by:
-
Amit Kucheria authored
On platforms that have a modem, sensor 0 monitors the modem. Signed-off-by:
-
Amit Kucheria authored
efficiency comes from downstream. The valid upstream property is capacity-dmips-mhz but until we can come up with those numbers, remove this property. Signed-off-by:
-
Amit Kucheria authored
We've earlier added support to split the register address space into TM and SROT regions. Split up the regmap address space into two for msm8998 that has a similar register layout. The order is important (TM before SROT) because we make an assumption that SROT is always the second address space in order to support legacy DTs. Signed-off-by:
-
- 28 Mar, 2019 5 commits
-
-
Rajendra Nayak authored
In order to fix dependencies with rpmpd DT entries, the header was dropped and hardcoded values were added for opp-level, during the previous merge window. Add the header back in now and remove the hardcodings, effectively reverting commit '08585d21: arm64: dts: sdm845: Fixup dependency on RPMPD includes' Signed-off-by:
Andy Gross <andy.gross@linaro.org>
-
Bjorn Andersson authored
Enable blsp1_uart3, define its pinconf and add the bluetooth node. It seems provisioning is lacking a valid BD address, preventing the interface from initializing, so provide a dummy for now. Tested-by:
Vinod Koul <vkoul@kernel.org> Reviewed-by:
-
Jorge Ramirez-Ortiz authored
Define the EVB pms405_s3 supplies. Signed-off-by:
Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org> Signed-off-by:
-
Jorge Ramirez-Ortiz authored
The PMS405 sports 5 SMPS and 13 LDO regulators, add the regulators to pms405 DTS. Signed-off-by:
-
Marc Gonzalez authored
Add host controller and PHY DT nodes. Tested-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
-
