- 09 Apr, 2024 16 commits
-
-
Paolo Abeni authored
Daniel Machon says: ==================== Add support for flower actions mirred and redirect This series adds support for the two tc flower actions mirred and redirect. Both actions are implemented by means of a port mask and a mask mode. The mask mode controls how the mask is applied, and together they are used by the switch to make a forwarding decision. Both actions are configurable via the IS0 or IS2 VCAP's (ingress stage 0 and 2, respectively). Patch #1: adds support for tc flower mirred action. Patch #2: adds support for tc flower redirect action. Signed-off-by:
Daniel Machon <daniel.machon@microchip.com> ==================== Link: https://lore.kernel.org/r/20240405-mirror-redirect-actions-v2-0-875d4c1927c8@microchip.comSigned-off-by:
Paolo Abeni <pabeni@redhat.com>
-
Daniel Machon authored
Add support for the flower redirect action. Two VCAP actions are encoded in the rule - one for the port mask, and one for the port mask mode. When the rule is hit, the port mask is used as the final destination set, replacing all other port masks. Signed-off-by:
-
Daniel Machon authored
Add support for tc flower mirred action. Two VCAP actions are encoded in the rule - one for the port mask, and one for the port mask mode. When the rule is hit, the destination mask is OR'ed with the port mask. Also add new VCAP function for supporting 72-bit wide actions, and a tc helper for setting the port forwarding mask. Signed-off-by:
-
Paolo Abeni authored
Diogo Ivo says: ==================== Support ICSSG-based Ethernet on AM65x SR1.0 devices This series extends the current ICSSG-based Ethernet driver to support AM65x Silicon Revision 1.0 devices. Notable differences between the Silicon Revisions are that there is no TX core in SR1.0 with this being handled by the firmware, requiring extra DMA channels to manage communication with the firmware (with the firmware being different as well) and in the packet classifier. The motivation behind it is that a significant number of Siemens devices containing SR1.0 silicon have been deployed in the field and need to be supported and updated to newer kernel versions without losing functionality. This series is based on TI's 5.10 SDK [1]. The fifth version of this patch series can be found in [2]. Compared to the last version of the patch set there are only changes in patch 05/10, where the fields of a struct are now explicitly declared as __le32 so that we can properly interpret them. Both of the problems mentioned in v4 have been addressed by disabling those functionalities, meaning that this driver currently only supports one TX queue and does not support a 100Mbit/s half-duplex connection. The removal of these features has been commented in the appropriate locations in the code. [1]: https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/?h=ti-linux-5.10.y [2]: https://lore.kernel.org/netdev/20240326110709.26165-1-diogo.ivo@siemens.com/ ==================== Link: https://lore.kernel.org/r/20240403104821.283832-1-diogo.ivo@siemens.comSigned-off-by:
-
Diogo Ivo authored
Add the PRUeth driver for the ICSSG subsystem found in AM65x SR1.0 devices. The main differences that set SR1.0 and SR2.0 apart are the missing TXPRU core in SR1.0, two extra DMA channels for management purposes and different firmware that needs to be configured accordingly. Based on the work of Roger Quadros, Vignesh Raghavendra and Grygorii Strashko in TI's 5.10 SDK [1]. [1]: https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/?h=ti-linux-5.10.yCo-developed-by:
Jan Kiszka <jan.kiszka@siemens.com> Signed-off-by:
Diogo Ivo <diogo.ivo@siemens.com> Reviewed-by:
MD Danish Anwar <danishanwar@ti.com> Signed-off-by:
-
Diogo Ivo authored
Some parts of the logic differ only slightly between Silicon Revisions. In these cases add the bits that differ to a common function that executes those bits conditionally based on the Silicon Revision. Based on the work of Roger Quadros, Vignesh Raghavendra and Grygorii Strashko in TI's 5.10 SDK [1]. [1]: https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/?h=ti-linux-5.10.yCo-developed-by:
Roger Quadros <rogerq@kernel.org> Reviewed-by:
-
Diogo Ivo authored
Add the functions to configure the SR1.0 packet classifier. Based on the work of Roger Quadros in TI's 5.10 SDK [1]. [1]: https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/?h=ti-linux-5.10.yCo-developed-by:
-
Diogo Ivo authored
As SR1.0 uses the current higher priority channel to send commands to the firmware, take this into account when setting/getting the number of channels to/from the user. Based on the work of Roger Quadros in TI's 5.10 SDK [1]. [1]: https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/?h=ti-linux-5.10.yCo-developed-by:
-
Diogo Ivo authored
Correctly adjust the IPG based on the Silicon Revision. Based on the work of Roger Quadros, Vignesh Raghavendra and Grygorii Strashko in TI's 5.10 SDK [1]. [1]: https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/?h=ti-linux-5.10.yCo-developed-by:
-
Diogo Ivo authored
Add a field to distinguish between SR1.0 and SR2.0 in the driver as well as the necessary structures to program SR1.0. Based on the work of Roger Quadros in TI's 5.10 SDK [1]. [1]: https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/?h=ti-linux-5.10.yCo-developed-by:
-
Diogo Ivo authored
Define the firmware configuration structure and commands needed to communicate with SR1.0 firmware, as well as SR1.0 buffer information where it differs from SR2.0. Based on the work of Roger Quadros, Murali Karicheri and Grygorii Strashko in TI's 5.10 SDK [1]. [1]: https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/?h=ti-linux-5.10.yCo-developed-by:
-
Diogo Ivo authored
In order to allow code sharing between Silicon Revisions 1.0 and 2.0 move all functions that can be shared into a common file. This commit introduces no functional changes. Signed-off-by:
-
Diogo Ivo authored
As these addresses can be useful outside of checking if an address is a multicast address (for example in device drivers) make them accessible to users of etherdevice.h to avoid code duplication. Signed-off-by:
-
Diogo Ivo authored
Silicon Revision 1.0 of the AM65x came with a slightly different ICSSG support: Only 2 PRUs per slice are available and instead 2 additional DMA channels are used for management purposes. We have no restrictions on specified PRUs, but the DMA channels need to be adjusted. Co-developed-by:
Conor Dooley <conor.dooley@microchip.com> Reviewed-by:
-
Dan Carpenter authored
These error paths accidentally return "ret" which is zero/success instead of the correct error code. Fixes: 71e79430 ("net: phy: air_en8811h: Add the Airoha EN8811H PHY driver") Signed-off-by:
Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by:
Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/7ef2e230-dfb7-4a77-8973-9e5be1a99fc2@moroto.mountainSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Allen Pais authored
The only generic interface to execute asynchronously in the BH context is tasklet; however, it's marked deprecated and has some design flaws. To replace tasklets, BH workqueue support was recently added. A BH workqueue behaves similarly to regular workqueues except that the queued work items are executed in the BH context. This patch converts drivers/net/archnet/* from tasklet to BH workqueue. Based on the work done by Tejun Heo <tj@kernel.org> Branch: https://git.kernel.org/pub/scm/linux/kernel/git/tj/wq.git for-6.10 Signed-off-by:
Allen Pais <allen.lkml@gmail.com> Link: https://lore.kernel.org/r/20240403162306.20258-1-apais@linux.microsoft.comSigned-off-by:
-
- 08 Apr, 2024 24 commits
-
-
Heiner Kallweit authored
A user reported an unknown chip version. According to the r8168 vendor driver it's called RTL8168M, but handling is identical to RTL8168H. So let's simply treat it as RTL8168H. Tested-by:
Евгений <octobergun@gmail.com> Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Parav Pandit says: ==================== devlink: Add port function attribute for IO EQs Currently, PCI SFs and VFs use IO event queues to deliver netdev per channel events. The number of netdev channels is a function of IO event queues. In the second scenario of an RDMA device, the completion vectors are also a function of IO event queues. Currently, an administrator on the hypervisor has no means to provision the number of IO event queues for the SF device or the VF device. Device/firmware determines some arbitrary value for these IO event queues. Due to this, the SF netdev channels are unpredictable, and consequently, the performance is too. This short series introduces a new port function attribute: max_io_eqs. The goal is to provide administrators at the hypervisor level with the ability to provision the maximum number of IO event queues for a function. This gives the control to the administrator to provision right number of IO event queues and have predictable performance. Examples of when an administrator provisions (set) maximum number of IO event queues when using switchdev mode: $ devlink port show pci/0000:06:00.0/1 pci/0000:06:00.0/1: type eth netdev enp6s0pf0vf0 flavour pcivf pfnum 0 vfnum 0 function: hw_addr 00:00:00:00:00:00 roce enable max_io_eqs 10 $ devlink port function set pci/0000:06:00.0/1 max_io_eqs 20 $ devlink port show pci/0000:06:00.0/1 pci/0000:06:00.0/1: type eth netdev enp6s0pf0vf0 flavour pcivf pfnum 0 vfnum 0 function: hw_addr 00:00:00:00:00:00 roce enable max_io_eqs 20 This sets the corresponding maximum IO event queues of the function before it is enumerated. Thus, when the VF/SF driver reads the capability from the device, it sees the value provisioned by the hypervisor. The driver is then able to configure the number of channels for the net device, as well as the number of completion vectors for the RDMA device. The device/firmware also honors the provisioned value, hence any VF/SF driver attempting to create IO EQs beyond provisioned value results in an error. With above setting now, the administrator is able to achieve the 2x performance on SFs with 20 channels. In second example when SF was provisioned for a container with 2 cpus, the administrator provisioned only 2 IO event queues, thereby saving device resources. With the above settings now in place, the administrator achieved 2x performance with the SF device with 20 channels. In the second example, when the SF was provisioned for a container with 2 CPUs, the administrator provisioned only 2 IO event queues, thereby saving device resources. changelog: v2->v3: - limited to 80 chars per line in devlink - fixed comments from Jakub in mlx5 driver to fix missing mutex unlock on error path v1->v2: - limited comment to 80 chars per line in header file - fixed set function variables for reverse christmas tree - fixed comments from Kalesh - fixed missing kfree in get call - returning error code for get cmd failure - fixed error msg copy paste error in set on cmd failure ==================== Signed-off-by: -
Parav Pandit authored
Implement get and set for the maximum IO event queues for SF and VF. This enables administrator on the hypervisor to control the maximum IO event queues which are typically used to derive the maximum and default number of net device channels or rdma device completion vectors. Reviewed-by:
Shay Drory <shayd@nvidia.com> Signed-off-by:
Parav Pandit <parav@nvidia.com> Reviewed-by:
Jiri Pirko <jiri@nvidia.com> Signed-off-by:
-
Parav Pandit authored
Many devices send event notifications for the IO queues, such as tx and rx queues, through event queues. Enable a privileged owner, such as a hypervisor PF, to set the number of IO event queues for the VF and SF during the provisioning stage. example: Get maximum IO event queues of the VF device:: $ devlink port show pci/0000:06:00.0/2 pci/0000:06:00.0/2: type eth netdev enp6s0pf0vf1 flavour pcivf pfnum 0 vfnum 1 function: hw_addr 00:00:00:00:00:00 ipsec_packet disabled max_io_eqs 10 Set maximum IO event queues of the VF device:: $ devlink port function set pci/0000:06:00.0/2 max_io_eqs 32 $ devlink port show pci/0000:06:00.0/2 pci/0000:06:00.0/2: type eth netdev enp6s0pf0vf1 flavour pcivf pfnum 0 vfnum 1 function: hw_addr 00:00:00:00:00:00 ipsec_packet disabled max_io_eqs 32 Reviewed-by: -
Eric Dumazet authored
Print these additional fields in skb_dump() to ease debugging. - mac_len - csum_start (in v2, at Willem suggestion) - csum_offset (in v2, at Willem suggestion) - priority - mark - alloc_cpu - vlan_all - encapsulation - inner_protocol - inner_mac_header - inner_network_header - inner_transport_header Signed-off-by:
Eric Dumazet <edumazet@google.com> Reviewed-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
-
David S. Miller authored
Andrew Lunn says: ==================== net: Clean up some EEE code Previous patches have reworked the API between phylib and MAC drivers with respect to EEE, pushing most of the work into phylib. These two patches rework two drivers to make use of the new API, and fix their EEE implementation, so that EEE is configured in the MAC based on what is actually negotiated during autoneg. Compile tested only. ==================== Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Andrew Lunn authored
The enabling/disabling of EEE in the MAC should happen as a result of auto negotiation. So move the enable/disable into lan743x_phy_link_status_change() which gets called by phylib when there is a change in link status. lan743x_ethtool_set_eee() now just programs the hardware with the LTI timer value, and passed everything else to phylib, so it can correctly setup the PHY. lan743x_ethtool_get_eee() relies on phylib doing most of the work, the MAC driver just adds the LTI timer value. Signed-off-by:
Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by:
-
Andrew Lunn authored
The enabling/disabling of EEE in the MAC should happen as a result of auto negotiation. So move the enable/disable into lan783xx_phy_link_status_change() which gets called by phylib when there is a change in link status. lan78xx_set_eee() now just programs the hardware with the LPI timer value, and passed everything else to phylib, so it can correctly setup the PHY. lan743x_get_eee() relies on phylib doing most of the work, the MAC driver just adds the LPI timer value. Call phy_support_eee() to indicate the MAC does actually support EEE. Signed-off-by:
-
Jason Xing authored
The reason codes are handled in two ways nowadays (quoting Mat Martineau): 1. Sending in the MPTCP option on RST packets when there is no subflow context available (these use subflow_add_reset_reason() and directly call a TCP-level send_reset function) 2. The "normal" way via subflow->reset_reason. This will propagate to both the outgoing reset packet and to a local path manager process via netlink in mptcp_event_sub_closed() RFC 8684 defines the skb reset reason behaviour which is not required even though in some places: A host sends a TCP RST in order to close a subflow or reject an attempt to open a subflow (MP_JOIN). In order to let the receiving host know why a subflow is being closed or rejected, the TCP RST packet MAY include the MP_TCPRST option (Figure 15). The host MAY use this information to decide, for example, whether it tries to re-establish the subflow immediately, later, or never. Since the commit dc87efdb ("mptcp: add mptcp reset option support") introduced this feature about three years ago, we can fully use it. There remains some places where we could insert reason into skb as we can see in this patch. Many thanks to Mat and Paolo for help:) Signed-off-by:Jason Xing <kernelxing@tencent.com> Acked-by:
-
Guillaume Nault authored
Add a "scope" parameter to ip_route_output() so that callers don't have to override the tos parameter with the RTO_ONLINK flag if they want a local scope. This will allow converting flowi4_tos to dscp_t in the future, thus allowing static analysers to flag invalid interactions between "tos" (the DSCP bits) and ECN. Only three users ask for local scope (bonding, arp and atm). The others continue to use RT_SCOPE_UNIVERSE. While there, add a comment to warn users about the limitations of ip_route_output(). Signed-off-by:
Guillaume Nault <gnault@redhat.com> Acked-by: Leon Romanovsky <leonro@nvidia.com> # infiniband Signed-off-by:
-
Venkat Venkatsubra authored
In case of stacked devices, to help propagate the down link state from the parent/root device (to this leaf device), handle NETDEV_DOWN event like it is done now for NETDEV_UP. In the below example, ens5 is the host interface which is the parent of the ipvlan interface eth0 in the container. Host: [root@gkn-podman-x64 ~]# ip link set ens5 down [root@gkn-podman-x64 ~]# ip -d link show dev ens5 3: ens5: <BROADCAST,MULTICAST> mtu 9000 qdisc mq state DOWN ... [root@gkn-podman-x64 ~]# Container: [root@testnode-ol8 /]# ip -d link show dev eth0 2: eth0@if3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 9000 state UNKNOWN ... ipvlan mode l2 bridge ... [root@testnode-ol8 /]# eth0's state continues to show up as UP even though ens5 is now DOWN. For macvlan the handling of NETDEV_DOWN event was added in commit 80fd2d6c ("macvlan: Change status when lower device goes down"). Reported-by:Gia-Khanh Nguyen <gia-khanh.nguyen@oracle.com> Signed-off-by:
Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com> Reviewed-by:
-
Eric Dumazet authored
Although the code is correct, the following line copy_from_sockptr(&req_u.req, optval, len)); triggers this warning : memcpy: detected field-spanning write (size 28) of single field "dst" at include/linux/sockptr.h:49 (size 16) Refactor the code to be more explicit. Reported-by:
syzbot <syzkaller@googlegroups.com> Signed-off-by:
Kees Cook <keescook@chromium.org> Reviewed-by:
-
Niklas Schnelle authored
In a future patch HAS_IOPORT=n will disable inb()/outb() and friends at compile time. We thus need to add HAS_IOPORT as dependency for those drivers requiring them. For the DEFXX driver the use of I/O ports is optional and we only need to fence specific code paths. It also turns out that with HAS_IOPORT handled explicitly HAMRADIO does not need the !S390 dependency and successfully builds the bpqether driver. Acked-by:
Marc Kleine-Budde <mkl@pengutronix.de> Acked-by:
Maciej W. Rozycki <macro@orcam.me.uk> Co-developed-by:
Arnd Bergmann <arnd@kernel.org> Signed-off-by:
Niklas Schnelle <schnelle@linux.ibm.com> Signed-off-by:
-
David S. Miller authored
Matthieu Baerts says: ==================== selftests: mptcp: cleanups and 'ip mptcp' support Here are some patches from Geliang, doing different cleanups, and supporting 'ip mptcp' in more MPTCP selftests. Patch 1 checks that TC is available in selftests requiring it. Patch 2 adds 'ms' units in TC commands, to avoid confusions. Patches 3-9 are some prerequisites for patch 10: some export code from mptcp_join.sh to mptcp_lib.sh, to be re-used in pm_netlink.sh, mptcp_sockopt.sh and simult_flows.sh ; and others add helpers to pm_netlink.sh to easily support both 'ip mptcp' and 'pm_nl_ctl' tools to interact with the in-kernel MPTCP path-manager. Patch 10 adds a '-i' parameter in mptcp_sockopt.sh, pm_netlink.sh, and simult_flows.sh to use 'ip mptcp' tool instead of 'pm_nl_ctl'. Patch 11 fixes some ShellCheck warnings in pm_netlink.sh, in order to drop a ShellCheck's 'disable' instruction. ==================== Signed-off-by:
Matthieu Baerts (NGI0) <matttbe@kernel.org> Signed-off-by:
-
Geliang Tang authored
Now there are only a few of variables are not using double quotes. Modifying them, then "shellcheck disable=SC2086" can be dropped. Signed-off-by:
Geliang Tang <tanggeliang@kylinos.cn> Reviewed-by:
-
Geliang Tang authored
This patch adds '-i' option for mptcp_sockopt.sh, pm_netlink.sh, and simult_flows.sh, to use 'ip mptcp' command in the tests instead of 'pm_nl_ctl'. Update usage() correspondingly. Signed-off-by:
-
Geliang Tang authored
Use those newly added pm_nl endpoint ops helpers to replace all 'pm_nl_ctl' commands with 'limits', 'add', 'del', 'flush', 'show' and 'set' arguments in scripts mptcp_sockopt.sh and simult_flows.sh. In pm_netlink.sh, add wrappers of there helpers to make the function names shorter. Then use the wrappers to replace all 'pm_nl_ctl' commands. Signed-off-by:
-
Geliang Tang authored
This patch exports six endpoint operation helpers with pm_nl_ prefix, pm_nl_set_limits(), pm_nl_add_endpoint(), pm_nl_del_endpoint(), pm_nl_flush_endpoint(), pm_nl_show_endpoints() and pm_nl_change_endpoint() into mptcp_lib.sh as public functions, and renamed each of them with a mptcp_lib_ prefix. Then these old pm_nl_ prefix helpers in mptcp_join.sh can be wrappers of mptcp_lib_ prefix ones. Signed-off-by:
-
Geliang Tang authored
This patch uses 'case' statements to simplify pm_nl_add_endpoint() and pm_nl_check_endpoint(). And simplify pm_nl_check_endpoint() with check_output() helper. Also update pm_nl_del_endpoint() to avoid the 'double quote' shellcheck warning. Signed-off-by:
-
Geliang Tang authored
The output formats of 'ip mptcp' commands are much different from that of 'pm_nl_ctl' commands. A new 'change_address' helper is added here, to change the flag of an address. This is a bit similar to mptcp_join.sh's pm_nl_change_endpoint(). Usage: Address ID - pm_nl_change_endpoint $ns id $id $flags IP address - change_address $ns $addr $flags Use this new helper in pm_netlink.sh to replace all 'pm_nl_ctl set' commands. Signed-off-by:
-
Geliang Tang authored
The output formats of 'ip mptcp' commands are much different from that of 'pm_nl_ctl' commands. This patch adds a new helper format_endpoints() to format the outputs of 'ip mptcp' and 'pm_nl_ctl' with 'endpoints' arguments to hide these differences. A new helper named get_endpoint() has also been added to show a specific endpoint identified by the given address ID, similar to mptcp_join.sh's pm_nl_show_endpoints() helper, but showing all entries. Use these two helpers in mptcp_join.sh and pm_netlink.sh to replace all 'pm_nl_ctl get' commands and outputs of 'pm_nl_ctl dump/get'. Suggested-by:
-
Geliang Tang authored
The output format of 'ip mptcp limits' command is much different from that of 'pm_nl_ctl limits' command. This patch adds format_limits() helper to format the outputs of these two commands to hide the difference. get_limits() has been added to show the limits. Use these two helpers in pm_netlink.sh to replace all 'pm_nl_ctl limits' commands and outputs. Signed-off-by:
-
Geliang Tang authored
This patch exports ip_mptcp into mptcp_lib.sh as a public variable, named MPTCP_LIB_IP_MPTCP. Add a helper mptcp_lib_set_ip_mptcp() to set it, and a helper mptcp_lib_is_ip_mptcp() to test whether it is set. Use these two helpers in mptcp_join.sh. This patch is prepared for coming commits. Signed-off-by:
-
Geliang Tang authored
'delay 1' in tc-netem is confusing, not sure if it's a delay of 1 second or 1 millisecond. This patch explicitly adds millisecond units to make these commands clearer. Signed-off-by:
-
