- 11 May, 2014 1 commit
-
-
Emmanuel Grumbach authored
There was a deadlock in monitor mode when we were setting the channel if the channel was not 1. ====================================================== [ INFO: possible circular locking dependency detected ] 3.14.3 #4 Not tainted ------------------------------------------------------- iw/3323 is trying to acquire lock: (&local->chanctx_mtx){+.+.+.}, at: [<ffffffffa062e2f2>] ieee80211_vif_release_channel+0x42/0xb0 [mac80211] but task is already holding lock: (&local->iflist_mtx){+.+...}, at: [<ffffffffa0609e0a>] ieee80211_set_monitor_channel+0x5a/0x1b0 [mac80211] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #2 (&local->iflist_mtx){+.+...}: [<ffffffff810d95bb>] __lock_acquire+0xb3b/0x13b0 [<ffffffff810d9ee0>] lock_acquire+0xb0/0x1f0 [<ffffffff817eb9c8>] mutex_lock_nested+0x78/0x4f0 [<ffffffffa06225cf>] ieee80211_iterate_active_interfaces+0x2f/0x60 [mac80211] [<ffffffffa0518189>] iwl_mvm_recalc_multicast+0x49/0xa0 [iwlmvm] [<ffffffffa051822e>] iwl_mvm_configure_filter+0x4e/0x70 [iwlmvm] [<ffffffffa05e6d43>] ieee80211_configure_filter+0x153/0x5f0 [mac80211] [<ffffffffa05e71f5>] ieee80211_reconfig_filter+0x15/0x20 [mac80211] [snip] -> #1 (&mvm->mutex){+.+.+.}: [<ffffffff810d95bb>] __lock_acquire+0xb3b/0x13b0 [<ffffffff810d9ee0>] lock_acquire+0xb0/0x1f0 [<ffffffff817eb9c8>] mutex_lock_nested+0x78/0x4f0 [<ffffffffa0517246>] iwl_mvm_add_chanctx+0x56/0xe0 [iwlmvm] [<ffffffffa062ca1e>] ieee80211_new_chanctx+0x13e/0x410 [mac80211] [<ffffffffa062d953>] ieee80211_vif_use_channel+0x1c3/0x5a0 [mac80211] [<ffffffffa06035ab>] ieee80211_add_virtual_monitor+0x1ab/0x6b0 [mac80211] [<ffffffffa06052ea>] ieee80211_do_open+0xe6a/0x15a0 [mac80211] [<ffffffffa0605a79>] ieee80211_open+0x59/0x60 [mac80211] [snip] -> #0 (&local->chanctx_mtx){+.+.+.}: [<ffffffff810d6cb7>] check_prevs_add+0x977/0x980 [<ffffffff810d95bb>] __lock_acquire+0xb3b/0x13b0 [<ffffffff810d9ee0>] lock_acquire+0xb0/0x1f0 [<ffffffff817eb9c8>] mutex_lock_nested+0x78/0x4f0 [<ffffffffa062e2f2>] ieee80211_vif_release_channel+0x42/0xb0 [mac80211] [<ffffffffa0609ec3>] ieee80211_set_monitor_channel+0x113/0x1b0 [mac80211] [<ffffffffa058fb37>] cfg80211_set_monitor_channel+0x77/0x2b0 [cfg80211] [<ffffffffa056e0b2>] __nl80211_set_channel+0x122/0x140 [cfg80211] [<ffffffffa0581374>] nl80211_set_wiphy+0x284/0xaf0 [cfg80211] [snip] other info that might help us debug this: Chain exists of: &local->chanctx_mtx --> &mvm->mutex --> &local->iflist_mtx Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&local->iflist_mtx); lock(&mvm->mutex); lock(&local->iflist_mtx); lock(&local->chanctx_mtx); *** DEADLOCK *** This deadlock actually occurs: INFO: task iw:3323 blocked for more than 120 seconds. Not tainted 3.14.3 #4 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. iw D ffff8800c8afcd80 4192 3323 3322 0x00000000 ffff880078fdb7e0 0000000000000046 ffff8800c8afcd80 ffff880078fdbfd8 00000000001d5540 00000000001d5540 ffff8801141b0000 ffff8800c8afcd80 ffff880078ff9e38 ffff880078ff9e38 ffff880078ff9e40 0000000000000246 Call Trace: [<ffffffff817ea841>] schedule_preempt_disabled+0x31/0x80 [<ffffffff817ebaed>] mutex_lock_nested+0x19d/0x4f0 [<ffffffffa06225cf>] ? ieee80211_iterate_active_interfaces+0x2f/0x60 [mac80211] [<ffffffffa06225cf>] ? ieee80211_iterate_active_interfaces+0x2f/0x60 [mac80211] [<ffffffffa052a680>] ? iwl_mvm_power_mac_update_mode+0xc0/0xc0 [iwlmvm] [<ffffffffa06225cf>] ieee80211_iterate_active_interfaces+0x2f/0x60 [mac80211] [<ffffffffa0529357>] _iwl_mvm_power_update_binding+0x27/0x80 [iwlmvm] [<ffffffffa0516eb1>] iwl_mvm_unassign_vif_chanctx+0x81/0xc0 [iwlmvm] [<ffffffffa062d3ff>] __ieee80211_vif_release_channel+0xdf/0x470 [mac80211] [<ffffffffa062e2fa>] ieee80211_vif_release_channel+0x4a/0xb0 [mac80211] [<ffffffffa0609ec3>] ieee80211_set_monitor_channel+0x113/0x1b0 [mac80211] [<ffffffffa058fb37>] cfg80211_set_monitor_channel+0x77/0x2b0 [cfg80211] [<ffffffffa056e0b2>] __nl80211_set_channel+0x122/0x140 [cfg80211] [<ffffffffa0581374>] nl80211_set_wiphy+0x284/0xaf0 [cfg80211] This fixes https://bugzilla.kernel.org/show_bug.cgi?id=75541 Cc: <stable@vger.kernel.org> [3.13+] Reviewed-by:Johannes Berg <johannes.berg@intel.com> Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com>
-
- 07 May, 2014 1 commit
-
-
Emmanuel Grumbach authored
In case RFKILL is in KILL position, the NIC will issue an interrupt straight away. This interrupt won't be sent because it is masked in the hardware. But if our interrupt service routine is called for another reason (SHARED_IRQ), then we'll look at the interrupt cause and service it. This can cause bad things if we are not ready yet. Explicitly clean the interrupt cause register to make sure we won't service anything before we are ready to. Cc: <stable@vger.kernel.org> [3.14] Reported-and-tested-by:
Alexander Monakov <amonakov@gmail.com> Reviewed-by:
-
- 06 May, 2014 3 commits
-
-
David Spinadel authored
Currently the FW doesn't support sched scan while associated, Prevent it. Signed-off-by:
David Spinadel <david.spinadel@intel.com> Reviewed-by:
Luciano Coelho <luciano.coelho@intel.com> Signed-off-by:
-
Emmanuel Grumbach authored
My bad - I forgot to update this when sending the patch upstream. Fixes: 87d5e415 ("iwlwifi: mvm: rs: reinit rs if no tx for a long time") Signed-off-by:
-
Emmanuel Grumbach authored
The commit below introduced a bug in the validity bits in init. Due to that, all the Coex mechanism stopped sending kills to the BT side. Fix that. Fixes: b9fae2d5 ("iwlwifi: mvm: BT Coex add support for Co-running block") Signed-off-by:
-
- 13 Apr, 2014 14 commits
-
-
Alexander Bondar authored
The firmware doesn't handle properly the fragmented scan. Stop using it. While at it change max_out_time and suspend_time units from usec to TUs as expected by firmware API. Signed-off-by:
Alexander Bondar <alexander.bondar@intel.com> Signed-off-by:
-
Emmanuel Grumbach authored
A few entries were wrong and this caused throughput issues. Cc: <stable@vger.kernel.org> [3.13+] Fixes: dac94da8 ("iwlwifi: mvm: new BT Coex API") Signed-off-by:
-
Eyal Shapira authored
The per rate stats should be cleared when aggregation state changes to avoid making rate scale decisions based on throughput figures which were collected prior to the aggregation state change and are now stale. While at it make sure any clearing of the per rate stats will get logged. Cc: <stable@vger.kernel.org> [3.14] Signed-off-by:
Eyal Shapira <eyalx.shapira@intel.com> Signed-off-by:
-
Eyal Shapira authored
Don't search columns which are unlikely to succeed as previous columns searched with less aggressive modulation failed. Cc: <stable@vger.kernel.org> [3.14] Signed-off-by:
-
Eyal Shapira authored
Allow switching back to legacy Tx columns so we'll stop doing HT/VHT in case we're far from the AP. Stop active aggregation when making a deciding to stay in a legacy column. Despite having low legacy rates in the LQ table lower entries it doesn't help much in case we're doing aggregations as the aggregation was being transmitted in the initial rate of the table. This should help traffic stalls when far from the AP. Cc: <stable@vger.kernel.org> [3.14] Signed-off-by:
-
Eyal Shapira authored
After being idle for a long time (>5sec) the rs statistics will be stale so we prefer to reset rs and start from legacy rates again. This gives better results when the attenuation increased signficantly (e.g. we got further from the AP) and after a while we start Tx Note that the first Tx after the idle period will still go out in the old modulation and rate but this seemed a simpler approach compared to adding a timer or modifying mac80211 for this. The negative impact is negligble as we'll recover quickly. Cc: <stable@vger.kernel.org> [3.14] Signed-off-by:
-
Eyal Shapira authored
Change the down/upscale decision logic a bit to be based on different success ratio thresholds. This fixes the implementation compared to the rate scale algorithm which was planned to yield optimal results. Also fix a case where a lower rate wasn't explored despite being a potential for better throughput. While at it rewrite rs_get_rate_action to be more clear and clean. Cc: <stable@vger.kernel.org> [3.14] Signed-off-by:
-
Eyal Shapira authored
The selection of the max expected throughput for a column didn't take into account the maximal allowed rate for the current peer. This can cause unnecessary switches during the search cycle to columns which have no chance of beating the current throughput. Signed-off-by:
-
Emmanuel Grumbach authored
It was missing. Cc: <stable@vger.kernel.org> [3.13+] Signed-off-by: -
Emmanuel Grumbach authored
This will allow to load the new firmware. Cc: <stable@vger.kernel.org> [3.14] Signed-off-by: -
Oren Givon authored
Add 2 new HW IDs for the 7265 series. Cc: <stable@vger.kernel.org> [3.13+] Signed-off-by:
Oren Givon <oren.givon@intel.com> Signed-off-by:
-
Emmanuel Grumbach authored
I forgot to send the new Look Up Table to the firmware and I also forgot to free the command which is kzalloc'ed. This code is relevant for 7265 device only. Signed-off-by: -
Eyal Shapira authored
mimo_delim was always set to 0 instead of pointing to the first SISO entry after MIMO rates. This can cause keep transmitting in MIMO even when we shouldn't. For example when the peer is requesting static SMPS. Cc: <stable@vger.kernel.org> [3.14] Signed-off-by:
-
Johannes Berg authored
If we have no beacon data before association, delay smart FIFO enablement until after we have this data. Not doing so can cause association failures in extremely silent environments (usually only a shielded box/room) as beacon RX is not sent to the host immediately, and then the association time event ends without the host receiving any beacon even though it was on the air - it's just stuck on the FIFO. Cc: <stable@vger.kernel.org> [3.14] Fixes: 1f3b0ff8 ("iwlwifi: mvm: Add Smart FIFO support") Signed-off-by:
-
- 20 Mar, 2014 6 commits
-
-
Arend van Spriel authored
In order to support the driver behaviour introduced by: commit d0575a5a703978c43e25128421158c78534ba100 Author: Daniel Kim <dekim@broadcom.com> Date: Wed Mar 12 18:12:14 2014 -0700 brcmfmac: Enable 40MHz bandwidth in 2GHz band and OBSS scanning in devices that do not support bwcap firmware command a fallback is added. Reviewed-by:Daniel (Deognyoun) Kim <dekim@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by:
Arend van Spriel <arend@broadcom.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Arend van Spriel authored
In the function brcmf_sdiod_request_data() an error message is logged, but the calling function retries it. This patch will only log an error message when retry limit is reached. The low-level error is still logged by a SDIO debug message. Reviewed-by:
-
Arend van Spriel authored
The watchdog thread waits on completion that is set from a timer. As the completion is count based this could mean that on a busy system the watchdog is handled multiple times with a very short interval. This is not the intended behaviour. After handling the watchdog it should wait for the next timer expiry. This is accomplished by reinitializing the completion. Reviewed-by:
Hante Meuleman <meuleman@broadcom.com> Reviewed-by:
-
Daniel Kim authored
This patch enables 40MHz bandwidth in 2GHz band after checking whether cfg80211 allows it or not, and enables OBSS scanning operations to to support 20/40 BSS coexistence. Reviewed-by:
-
John W. Linville authored
Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
-
-
- 19 Mar, 2014 15 commits
-
-
Marcel Holtmann authored
In Secure Connections Only mode, it is required that Secure Connections is used for pairing and that the link key is encrypted with AES-CCM using a P-256 authenticated combination key. If this is not the case, then new connection shall be refused or existing connections shall be dropped. Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
Johan Hedberg <johan.hedberg@intel.com>
-
Johan Hedberg authored
It is possible that pairing fails after we've already received remote identity information. One example of such a situation is when re-encryption using the LTK fails. In this case the hci_conn object has already been updated with the identity address but user space does not yet know about it (since we didn't notify it of the new IRK yet). To ensure user space doesn't get a Pair Device command response with an unknown address always use the same address in the response as was used for the original command. Signed-off-by:
-
Johan Hedberg authored
When performing SMP pairing with MITM protection one side needs to enter the passkey while the other side displays to the user what needs to be entered. Nowhere in the SMP specification does it say that the displaying side needs to any kind of confirmation of the passkey, even though a code comment in smp.c implies this. This patch removes the misleading comment and converts the code to use the passkey notification mgmt event instead of the passkey confirmation mgmt event. Signed-off-by:
-
Johan Hedberg authored
In some cases the current 250ms delay is not enough for the remote to receive the keys, as can be witnessed by the following log: > ACL Data RX: Handle 64 flags 0x02 dlen 21 [hci1] 231.414217 SMP: Signing Information (0x0a) len 16 Signature key: 555bb66b7ab3abc9d5c287c97fe6eb29 < ACL Data TX: Handle 64 flags 0x00 dlen 21 [hci1] 231.414414 SMP: Encryption Information (0x06) len 16 Long term key: 2a7cdc233c9a4b1f3ed31dd9843fea29 < ACL Data TX: Handle 64 flags 0x00 dlen 15 [hci1] 231.414466 SMP: Master Identification (0x07) len 10 EDIV: 0xeccc Rand: 0x322e0ef50bd9308a < ACL Data TX: Handle 64 flags 0x00 dlen 21 [hci1] 231.414505 SMP: Signing Information (0x0a) len 16 Signature key: bbda1b2076e2325aa66fbcdd5388f745 > HCI Event: Number of Completed Packets (0x13) plen 5 [hci1] 231.483130 Num handles: 1 Handle: 64 Count: 2 < HCI Command: LE Start Encryption (0x08|0x0019) plen 28 [hci1] 231.664211 Handle: 64 Random number: 0x5052ad2b75fed54b Encrypted diversifier: 0xb7c2 Long term key: a336ede66711b49a84bde9b41426692e > HCI Event: Command Status (0x0f) plen 4 [hci1] 231.666937 LE Start Encryption (0x08|0x0019) ncmd 1 Status: Success (0x00) > HCI Event: Number of Completed Packets (0x13) plen 5 [hci1] 231.712646 Num handles: 1 Handle: 64 Count: 1 > HCI Event: Disconnect Complete (0x05) plen 4 [hci1] 232.562587 Status: Success (0x00) Handle: 64 Reason: Remote User Terminated Connection (0x13) As can be seen, the last key (Signing Information) is sent at 231.414505 but the completed packets event for it comes only at 231.712646, i.e. roughly 298ms later. To have a better margin of error this patch increases the delay to 500ms. Signed-off-by: -
Johan Hedberg authored
This is a trivial coding style simplification by instead of having an extra early return to instead revert the if condition and do the single needed queue_work() call there. Signed-off-by:
-
Zhao, Gang authored
Macro ASSERT_RDEV_LOCK(rdev) is equal to ASSERT_RTNL(), so replace it with ASSERT_RTNL() and remove it. Signed-off-by:
Zhao, Gang <gamerh2o@gmail.com> Signed-off-by:
-
Zhao, Gang authored
RCU pointer bss->pub.beacon_ies is checked before in previous statement: if (rcu_access_pointer(bss->pub.beacon_ies)) continue; There is no need to check it twice(and in the wrong way :) ). Signed-off-by:
-
Emmanuel Grumbach authored
Add a bit in rx_status.vht_flags to let the low level driver notify mac80211 about a beamformed packet. Propagate this to the radiotap header. Signed-off-by:
-
Emmanuel Grumbach authored
On 2.4Ghz band, the channels overlap since the delta between different channels is 5Mhz while the width of the receiver is 20Mhz (at least). This means that we can hear beacons or probe responses from adjacent channels. These frames will have a significant lower RSSI which will feed all kinds of logic with inaccurate data. An obvious example is the roaming algorithm that will think our AP is getting weak and will try to move to another AP. In order to avoid this, update the signal only if the frame has been heard on the same channel as the one advertised by the AP in its DS / HT IEs. We refrain from updating the values only if the AP is already in the BSS list so that we will still have a valid (but inaccurate) value if the AP was heard on an adjacent channel only. To achieve this, stop taking the channel from DS / HT IEs in mac80211. The DS / HT IEs is taken into account to discard the frame if it was received on a disabled channel. This can happen due to the same phenomenon: the frame is sent on channel 12, but heard on channel 11 while channel 12 can be disabled on certain devices. Since this check is done in cfg80211, stop even checking this in mac80211. Signed-off-by:
-
Zhao, Gang authored
Function __cfg80211_join_ibss() is only used in net/wireless/ibss.c, so make it static. Signed-off-by:
-
Eliad Peller authored
Drivers might want to have private data in addition to all other ieee80211_tx_info.status fields. The current ieee80211_tx_info.rate_driver_data overlaps with some of the non-rate data (e.g. ampdu_ack_len), so it might not be good enough. Since we already know how much free bytes remained, simply use this size to define (void *) array. While on it, change ack_signal type from int to the more explicit s32 type. Signed-off-by:
Eliad Peller <eliadx.peller@intel.com> Signed-off-by:
-
Alexander Bondar authored
Assuming sched_scan_stop operation is synchronous the driver may not necessary call ieee80211_sched_scan_stopped_work. Since this work is the only place where sched_scan_sdata is released we can possibly run into situation when it is never released. Fix this by releasing it just after calling drv_sched_scan_stop. Signed-off-by:
-
Michael Braun authored
commit de74a1d9 "mac80211: fix WPA with VLAN on AP side with ps-sta" fixed an issue where queued multicast packets would be sent out encrypted with the key of an other bss. commit "7cbf9d01" "mac80211: fix oops on mesh PS broadcast forwarding" essentially reverted it, because vif.type cannot be AP_VLAN due to the check to vif.type in ieee80211_get_buffered_bc before. As the later commit intended to fix the MESH case, fix it by checking for IFTYPE_AP instead of IFTYPE_AP_VLAN. Cc: stable@vger.kernel.org Fixes: 7cbf9d01 ("mac80211: fix oops on mesh PS broadcast forwarding") Signed-off-by:
Michael Braun <michael-dev@fami-braun.de> Signed-off-by:
-
Vladimir Kondratiev authored
In the 802.11ad, aka DMG (Dynamic Multi-Gigabit), aka 60Ghz spec, maximum MSDU size extended to 7920 bytes. add #define for this. Signed-off-by:
Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by:
-
Johannes Berg authored
Since Stanislaw's patch removing the quiescing code, mac80211 had a race regarding suspend vs. authentication: as cfg80211 doesn't track authentication attempts, it can't abort them. Therefore the attempts may be kept running while suspending, which can lead to all kinds of issues, in at least some cases causing an error in iwlmvm firmware. Fix this by aborting the authentication attempt when suspending. Cc: stable@vger.kernel.org Fixes: 12e7f517 ("mac80211: cleanup generic suspend/resume procedures") Signed-off-by:
-
