Implement shared-writeable mmap for AFS.
Signed-off-by: David Howells <dhowells@redhat.com>

Get rid of the afs_writeback record that kAFS is using to match keys with
writes made by that key.

Instead, keep a list of keys that have a file open for writing and/or
sync'ing and iterate through those.
Signed-off-by: David Howells <dhowells@redhat.com>

Introduce a file-private data record for kAFS and put the key into it
rather than storing the key in file->private_data.
Signed-off-by: David Howells <dhowells@redhat.com>

It is not required that the afs client operate on port 7001.
The port could be in use because another kernel or userspace
client has already bound to it.

If the port is in use, just fallback to using a dynamic port.
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>

Because parsing of the directory wasn't being done under any sort of lock,
the pages holding the directory content can get invalidated whilst the
parsing is ongoing.

Further, the directory page check function gets called outside of the page
lock, so if the page gets cleared or updated, this may return reports of
bad magic numbers in the directory page.

Also, the directory may change size whilst checking and parsing are
ongoing, so more care needs to be taken here.

Fix this by:

 (1) Perform the page check from the page filling function before we set
     PageUptodate and drop the page lock.

 (2) Check for the file having shrunk and the page having been abandoned
     before checking the page contents.

 (3) Lock the page whilst parsing it for the directory iterator.

Whilst we're at it, add a tracepoint to report check failure.
Signed-off-by: David Howells <dhowells@redhat.com>

Add a pair of tracepoints to log the sending of pages for an FS.StoreData
or FS.StoreData64 operation.

Tracepoint afs_send_pages notes each set of pages added to the operation.
There may be several of these per operation as we get up at most 8
contiguous pages in one go because the bvec we're using is on the stack.

Tracepoint afs_sent_pages notes the end of adding data from a whole run of
pages to the operation and the completion of the request phase.
Signed-off-by: David Howells <dhowells@redhat.com>

Add tracepoints to trace the initiation and completion of client calls
within the kafs filesystem.

The afs_make_vl_call tracepoint watches calls to the volume location
database server.

The afs_make_fs_call tracepoint watches calls to the file server.

The afs_call_done tracepoint watches for call completion.
Signed-off-by: David Howells <dhowells@redhat.com>

The documentation that describes the #-prefix and the %-prefix used when
specifying the source to mount is has the descriptions the wrong way
round.  Switch them over.
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>

Fix the total-length calculation in afs_make_call() when the operation
being dispatched has data from a series of pages attached.

Despite the patched code looking like that it should reduce mathematically
to the current code, it doesn't because the 32-bit unsigned arithmetic
being used to calculate the page-offset-difference doesn't correctly extend
to a 64-bit value when the result is effectively negative.

Without this, some FS.StoreData operations that span multiple pages fail,
reporting too little or too much data.
Signed-off-by: David Howells <dhowells@redhat.com>

Only progress the AFS call state at the end of Tx phase from the callback
passed to rxrpc_kernel_send_data() rather than setting it before the last
data send call.
Signed-off-by: David Howells <dhowells@redhat.com>

YFS VL servers offer an upgraded Volume Location service that can return
IPv6 addresses to fileservers and volume servers in addition to IPv4
addresses using the YFSVL.GetEndpoints operation which we should use if
it's available.

To this end:

 (1) Make rxrpc_kernel_recv_data() return the call's current service ID so
     that the caller can detect service upgrade and see what the service
     was upgraded to.

 (2) When we see a VL server address we haven't seen before, send a
     VL.GetCapabilities operation to it with the service upgrade bit set.

     If we get an upgrade to the YFS VL service, change the service ID in
     the address list for that address to use the upgraded service and set
     a flag to note that this appears to be a YFS-compatible server.

 (3) If, when a server's addresses are being looked up, we note that we
     previously detected a YFS-compatible server, then send the
     YFSVL.GetEndpoints operation rather than VL.GetAddrsU.

 (4) Build a fileserver address list from the reply of YFSVL.GetEndpoints,
     including both IPv4 and IPv6 addresses.  Volume server addresses are
     discarded.

 (5) The address list is sorted by address and port now, instead of just
     address.  This allows multiple servers on the same host sitting on
     different ports.
Signed-off-by: David Howells <dhowells@redhat.com>

The current code assumes that volumes and servers are per-cell and are
never shared, but this is not enforced, and, indeed, public cells do exist
that are aliases of each other.  Further, an organisation can, say, set up
a public cell and a private cell with overlapping, but not identical, sets
of servers.  The difference is purely in the database attached to the VL
servers.

The current code will malfunction if it sees a server in two cells as it
assumes global address -> server record mappings and that each server is in
just one cell.

Further, each server may have multiple addresses - and may have addresses
of different families (IPv4 and IPv6, say).

To this end, the following structural changes are made:

 (1) Server record management is overhauled:

     (a) Server records are made independent of cell.  The namespace keeps
     	 track of them, volume records have lists of them and each vnode
     	 has a server on which its callback interest currently resides.

     (b) The cell record no longer keeps a list of servers known to be in
     	 that cell.

     (c) The server records are now kept in a flat list because there's no
     	 single address to sort on.

     (d) Server records are now keyed by their UUID within the namespace.

     (e) The addresses for a server are obtained with the VL.GetAddrsU
     	 rather than with VL.GetEntryByName, using the server's UUID as a
     	 parameter.

     (f) Cached server records are garbage collected after a period of
     	 non-use and are counted out of existence before purging is allowed
     	 to complete.  This protects the work functions against rmmod.

     (g) The servers list is now in /proc/fs/afs/servers.

 (2) Volume record management is overhauled:

     (a) An RCU-replaceable server list is introduced.  This tracks both
     	 servers and their coresponding callback interests.

     (b) The superblock is now keyed on cell record and numeric volume ID.

     (c) The volume record is now tied to the superblock which mounts it,
     	 and is activated when mounted and deactivated when unmounted.
     	 This makes it easier to handle the cache cookie without causing a
     	 double-use in fscache.

     (d) The volume record is loaded from the VLDB using VL.GetEntryByNameU
     	 to get the server UUID list.

     (e) The volume name is updated if it is seen to have changed when the
     	 volume is updated (the update is keyed on the volume ID).

 (3) The vlocation record is got rid of and VLDB records are no longer
     cached.  Sufficient information is stored in the volume record, though
     an update to a volume record is now no longer shared between related
     volumes (volumes come in bundles of three: R/W, R/O and backup).

and the following procedural changes are made:

 (1) The fileserver cursor introduced previously is now fleshed out and
     used to iterate over fileservers and their addresses.

 (2) Volume status is checked during iteration, and the server list is
     replaced if a change is detected.

 (3) Server status is checked during iteration, and the address list is
     replaced if a change is detected.

 (4) The abort code is saved into the address list cursor and -ECONNABORTED
     returned in afs_make_call() if a remote abort happened rather than
     translating the abort into an error message.  This allows actions to
     be taken depending on the abort code more easily.

     (a) If a VMOVED abort is seen then this is handled by rechecking the
     	 volume and restarting the iteration.

     (b) If a VBUSY, VRESTARTING or VSALVAGING abort is seen then this is
         handled by sleeping for a short period and retrying and/or trying
         other servers that might serve that volume.  A message is also
         displayed once until the condition has cleared.

     (c) If a VOFFLINE abort is seen, then this is handled as VBUSY for the
     	 moment.

     (d) If a VNOVOL abort is seen, the volume is rechecked in the VLDB to
     	 see if it has been deleted; if not, the fileserver is probably
     	 indicating that the volume couldn't be attached and needs
     	 salvaging.

     (e) If statfs() sees one of these aborts, it does not sleep, but
     	 rather returns an error, so as not to block the umount program.

 (5) The fileserver iteration functions in vnode.c are now merged into
     their callers and more heavily macroised around the cursor.  vnode.c
     is removed.

 (6) Operations on a particular vnode are serialised on that vnode because
     the server will lock that vnode whilst it operates on it, so a second
     op sent will just have to wait.

 (7) Fileservers are probed with FS.GetCapabilities before being used.
     This is where service upgrade will be done.

 (8) A callback interest on a fileserver is set up before an FS operation
     is performed and passed through to afs_make_call() so that it can be
     set on the vnode if the operation returns a callback.  The callback
     interest is passed through to afs_iget() also so that it can be set
     there too.

In general, record updating is done on an as-needed basis when we try to
access servers, volumes or vnodes rather than offloading it to work items
and special threads.

Notes:

 (1) Pre AFS-3.4 servers are no longer supported, though this can be added
     back if necessary (AFS-3.4 was released in 1998).

 (2) VBUSY is retried forever for the moment at intervals of 1s.

 (3) /proc/fs/afs/<cell>/servers no longer exists.
Signed-off-by: David Howells <dhowells@redhat.com>

Move server rotation code into its own file.
Signed-off-by: David Howells <dhowells@redhat.com>

Add an RCU replaceable address list structure to hold a list of server
addresses.  The list also holds the

To this end:

 (1) A cell's VL server address list can be loaded directly via insmod or
     echo to /proc/fs/afs/cells or dynamically from a DNS query for AFSDB
     or SRV records.

 (2) Anyone wanting to use a cell's VL server address must wait until the
     cell record comes online and has tried to obtain some addresses.

 (3) An FS server's address list, for the moment, has a single entry that
     is the key to the server list.  This will change in the future when a
     server is instead keyed on its UUID and the VL.GetAddrsU operation is
     used.

 (4) An 'address cursor' concept is introduced to handle iteration through
     the address list.  This is passed to the afs_make_call() as, in the
     future, stuff (such as abort code) that doesn't outlast the call will
     be returned in it.

In the future, we might want to annotate the list with information about
how each address fares.  We might then want to propagate such annotations
over address list replacement.

Whilst we're at it, we allow IPv6 addresses to be specified in
colon-delimited lists by enclosing them in square brackets.
Signed-off-by: David Howells <dhowells@redhat.com>

Overhaul the way that the in-kernel AFS client keeps track of cells in the
following manner:

 (1) Cells are now held in an rbtree to make walking them quicker and RCU
     managed (though this is probably overkill).

 (2) Cells now have a manager work item that:

     (A) Looks after fetching and refreshing the VL server list.

     (B) Manages cell record lifetime, including initialising and
     	 destruction.

     (B) Manages cell record caching whereby threads are kept around for a
     	 certain time after last use and then destroyed.

     (C) Manages the FS-Cache index cookie for a cell.  It is not permitted
     	 for a cookie to be in use twice, so we have to be careful to not
     	 allow a new cell record to exist at the same time as an old record
     	 of the same name.

 (3) Each AFS network namespace is given a manager work item that manages
     the cells within it, maintaining a single timer to prod cells into
     updating their DNS records.

     This uses the reduce_timer() facility to make the timer expire at the
     soonest timed event that needs happening.

 (4) When a module is being unloaded, cells and cell managers are now
     counted out using dec_after_work() to make sure the module text is
     pinned until after the data structures have been cleaned up.

 (5) Each cell's VL server list is now protected by a seqlock rather than a
     semaphore.
Signed-off-by: David Howells <dhowells@redhat.com>

Overhaul permit caching in AFS by making it per-vnode and sharing permit
lists where possible.

When most of the fileserver operations are called, they return a status
structure indicating the (revised) details of the vnode or vnodes involved
in the operation.  This includes the access mark derived from the ACL
(named CallerAccess in the protocol definition file).  This is cacheable
and if the ACL changes, the server will tell us that it is breaking the
callback promise, at which point we can discard the currently cached
permits.

With this patch, the afs_permits structure has, at the end, an array of
{ key, CallerAccess } elements, sorted by key pointer.  This is then cached
in a hash table so that it can be shared between vnodes with the same
access permits.

Permit lists can only be shared if they contain the exact same set of
key->CallerAccess mappings.

Note that that table is global rather than being per-net_ns.  If the keys
in a permit list cross net_ns boundaries, there is no problem sharing the
cached permits, since the permits are just integer masks.

Since permit lists pin keys, the permit cache also makes it easier for a
future patch to find all occurrences of a key and remove them by means of
setting the afs_permits::invalidated flag and then clearing the appropriate
key pointer.  In such an event, memory barriers will need adding.

Lastly, the permit caching is skipped if the server has sent either a
vnode-specific or an entire-server callback since the start of the
operation.
Signed-off-by: David Howells <dhowells@redhat.com>

Overhaul the AFS callback handling by the following means:

 (1) Don't give up callback promises on vnodes that we are no longer using,
     rather let them just expire on the server or let the server break
     them.  This is actually more efficient for the server as the callback
     lookup is expensive if there are lots of extant callbacks.

 (2) Only give up the callback promises we have from a server when the
     server record is destroyed.  Then we can just give up *all* the
     callback promises on it in one go.

 (3) Servers can end up being shared between cells if cells are aliased, so
     don't add all the vnodes being backed by a particular server into a
     big FID-indexed tree on that server as there may be duplicates.

     Instead have each volume instance (~= superblock) register an interest
     in a server as it starts to make use of it and use this to allow the
     processor for callbacks from the server to find the superblock and
     thence the inode corresponding to the FID being broken by means of
     ilookup_nowait().

 (4) Rather than iterating over the entire callback list when a mass-break
     comes in from the server, maintain a counter of mass-breaks in
     afs_server (cb_seq) and make afs_validate() check it against the copy
     in afs_vnode.

     It would be nice not to have to take a read_lock whilst doing this,
     but that's tricky without using RCU.

 (5) Save a ref on the fileserver we're using for a call in the afs_call
     struct so that we can access its cb_s_break during call decoding.

 (6) Write-lock around callback and status storage in a vnode and read-lock
     around getattr so that we don't see the status mid-update.

This has the following consequences:

 (1) Data invalidation isn't seen until someone calls afs_validate() on a
     vnode.  Unfortunately, we need to use a key to query the server, but
     getting one from a background thread is tricky without caching loads
     of keys all over the place.

 (2) Mass invalidation isn't seen until someone calls afs_validate().

 (3) Callback breaking is going to hit the inode_hash_lock quite a bit.
     Could this be replaced with rcu_read_lock() since inodes are destroyed
     under RCU conditions.
Signed-off-by: David Howells <dhowells@redhat.com>

Rename the server member of struct afs_call to cm_server as we're only
going to be using it for incoming calls for the Cache Manager service.
This makes it easier to differentiate from the pointer to the target server
for the client, which will point to a different structure to allow for
callback handling.
Signed-off-by: David Howells <dhowells@redhat.com>

In AFS's encoding of a UUID, the eight 'char' fields are all signed, so
represent them with __s8 rather than __u8.  This makes the compiler
sign-extend them correctly when XDR-encoding them.
Signed-off-by: David Howells <dhowells@redhat.com>

The handler for the CB.ProbeUuid operation in the cache manager is
implemented, but isn't listed in the switch-statement of operation
selection, so won't be used.  Fix this by adding it.
Signed-off-by: David Howells <dhowells@redhat.com>

If call->ret_reply0 is set, return call->reply[0] on success.  Change the
return type of afs_make_call() to long so that this can be passed back
without bit loss and then cast to a pointer if required.
Signed-off-by: David Howells <dhowells@redhat.com>

Condense struct afs_call's reply anchor members - reply{,2,3,4} - into an
array.
Signed-off-by: David Howells <dhowells@redhat.com>

The AFS abort code space is shared across all services, so there's no need
for separate abort_to_error translators for each service.

Consolidate them into a single function and remove the function pointers
for them.
Signed-off-by: David Howells <dhowells@redhat.com>

Allow VL server specifications to be given IPv6 addresses as well as IPv4
addresses, for example as:

	echo add foo.org 1111:2222:3333:0:4444:5555:6666:7777 >/proc/fs/afs/cells

Note that ':' is the expected separator for separating IPv4 addresses, but
if a ',' is detected or no '.' is detected in the string, the delimiter is
switched to ','.

This also works with DNS AFSDB or SRV record strings fetched by upcall from
userspace.
Signed-off-by: David Howells <dhowells@redhat.com>

Keep and pass sockaddr_rxrpc addresses around rather than keeping and
passing in_addr addresses to allow for the use of IPv6 and non-standard
port numbers in future.

This also allows the port and service_id fields to be removed from the
afs_call struct.
Signed-off-by: David Howells <dhowells@redhat.com>

Update the cache index structure in the following ways:

 (1) Don't use the volume name followed by the volume type as levels in the
     cache index.  Volumes can be renamed.  Use the volume ID instead.

 (2) Don't store the VLDB data for a volume in the tree.  If the volume
     database should be cached locally, then it should be done in a separate
     tree.

 (3) Expand the volume ID stored in the cache to 64 bits.

 (4) Expand the file/vnode ID stored in the cache to 96 bits.

 (5) Increment the cache structure version number to 1.
Signed-off-by: David Howells <dhowells@redhat.com>

Add some protocol definitions, including max field lengths, flag defs, an
XDR-encoded UUID def, more VL operation IDs and more fileserver abort
codes.
Signed-off-by: David Howells <dhowells@redhat.com>

Push the network namespace pointer to more places in AFS, including the
afs_server structure (which doesn't hold a ref on the netns).

In particular, afs_put_cell() now takes requires a net ns parameter so that
it can safely alter the netns after decrementing the cell usage count - the
cell will be deallocated by a background thread after being cached for a
period, which means that it's not safe to access it after reducing its
usage count.
Signed-off-by: David Howells <dhowells@redhat.com>

Keep a reference to the cell in the superblock info structure in addition
to the volume and net pointers.  This will make it easier to clean up in a
future patch in which afs_put_volume() will need the cell pointer.

Whilst we're at it, make the cell and volume getting functions return a
pointer to the object got to make the call sites look neater.
Signed-off-by: David Howells <dhowells@redhat.com>

Fix server reaping and make sure it's all done before we start trying to
purge cells, given that servers currently pin cells.
Signed-off-by: David Howells <dhowells@redhat.com>

Close the rxrpc socket only after we've purged the server records (and also
cell and volume records which might refer to servers) so that we can give
up the callbacks on each server.
Signed-off-by: David Howells <dhowells@redhat.com>

Lay the groundwork for supporting network namespaces (netns) to the AFS
filesystem by moving various global features to a network-namespace struct
(afs_net) and providing an instance of this as a temporary global variable
that everything uses via accessor functions for the moment.

The following changes have been made:

 (1) Store the netns in the superblock info.  This will be obtained from
     the mounter's nsproxy on a manual mount and inherited from the parent
     superblock on an automount.

 (2) The cell list is made per-netns.  It can be viewed through
     /proc/net/afs/cells and also be modified by writing commands to that
     file.

 (3) The local workstation cell is set per-ns in /proc/net/afs/rootcell.
     This is unset by default.

 (4) The 'rootcell' module parameter, which sets a cell and VL server list
     modifies the init net namespace, thereby allowing an AFS root fs to be
     theoretically used.

 (5) The volume location lists and the file lock manager are made
     per-netns.

 (6) The AF_RXRPC socket and associated I/O bits are made per-ns.

The various workqueues remain global for the moment.

Changes still to be made:

 (1) /proc/fs/afs/ should be moved to /proc/net/afs/ and a symlink emplaced
     from the old name.

 (2) A per-netns subsys needs to be registered for AFS into which it can
     store its per-netns data.

 (3) Rather than the AF_RXRPC socket being opened on module init, it needs
     to be opened on the creation of a superblock in that netns.

 (4) The socket needs to be closed when the last superblock using it is
     destroyed and all outstanding client calls on it have been completed.
     This prevents a reference loop on the namespace.

 (5) It is possible that several namespaces will want to use AFS, in which
     case each one will need its own UDP port.  These can either be set
     through /proc/net/afs/cm_port or the kernel can pick one at random.
     The init_ns gets 7001 by default.

Other issues that need resolving:

 (1) The DNS keyring needs net-namespacing.

 (2) Where do upcalls go (eg. DNS request-key upcall)?

 (3) Need something like open_socket_in_file_ns() syscall so that AFS
     command line tools attempting to operate on an AFS file/volume have
     their RPC calls go to the right place.
Signed-off-by: David Howells <dhowells@redhat.com>

Make wait_on_atomic_t() pass the TASK_* mode onto its action function as an
extra argument and make it 'unsigned int throughout.

Also, consolidate a bunch of identical action functions into a default
function that can do the appropriate thing for the mode.

Also, change the argument name in the bit_wait*() function declarations to
reflect the fact that it's the mode and not the bit number.

[Peter Z gives this a grudging ACK, but thinks that the whole atomic_t wait
should be done differently, though he's not immediately sure as to how]
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
cc: Ingo Molnar <mingo@kernel.org>

These AFS patches need the timer_reduce() patch from timers/core.
Signed-off-by: David Howells <dhowells@redhat.com>

Xin Long says:

====================
net: improve the process of redirect and toobig for ipv6 tunnels

Now let's say there are 3 kinds of icmp packets to process for tunnels,
toobig(needfrag), redirect, others, their process should be:

 - toobig(needfrag)
   update the lower dst's pmtu by route cache, also update sk dst's pmtu
   if possible, or it will be fine if sk dst pmtu will get updated on tx
   path.

 - redirect
   update the lower dst's gw by route cache and return, no need to send
   this redirect packet to user sk.

 - others
   send the packet to user's sk, or it will also be fine to use err_count
   to count it and report fail link on tx path.

All ipv4 tunnels basically follow this while some of ipv6 tunnels are
doing in different ways, like ip6gre and ip6_tunnels update tnl dev's
mtu instead of updating lower dst pmtu, no redirect process on their
err_handlers, which doesn't make any sense and even causes performance
problems.

This patchset is to improve the process of redirect and toobig for ip6gre
ip4ip6, ip6ip6 tunnels, as in ipv4 tunnels.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to remove some useless codes of redirect and fix some
indents on ip4ip6 and ip6ip6's err_handlers.

Note that redirect icmp packet is already processed in ip6_tnl_err,
the old redirect codes in ip4ip6_err actually never worked even
before this patch. Besides, there's no need to send redirect to
user's sk, it's for lower dst, so just remove it in this patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The same improvement in "ip6_gre: process toobig in a better way"
is needed by ip4ip6 and ip6ip6 as well.

Note that ip4ip6 and ip6ip6 will also update sk dst pmtu in their
err_handlers. Like I said before, gre6 could not do this as it's
inner proto is not certain. But for all of them, sk dst pmtu will
be updated in tx path if in need.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The same process for redirect in "ip6_gre: add the process for redirect
in ip6gre_err" is needed by ip4ip6 and ip6ip6 as well.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now ip6gre processes toobig icmp packet by setting gre dev's mtu in
ip6gre_err, which would cause few things not good:

  - It couldn't set mtu with dev_set_mtu due to it's not in user context,
    which causes route cache and idev->cnf.mtu6 not to be updated.

  - It has to update sk dst pmtu in tx path according to gredev->mtu for
    ip6gre, while it updates pmtu again according to lower dst pmtu in
    ip6_tnl_xmit.

  - To change dev->mtu by toobig icmp packet is not a good idea, it should
    only work on pmtu.

This patch is to process toobig by updating the lower dst's pmtu, as later
sk dst pmtu will be updated in ip6_tnl_xmit, the same way as in ip4gre.

Note that gre dev's mtu will not be updated any more, it doesn't make any
sense to change dev's mtu after receiving a toobig packet.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to add redirect icmp packet process for ip6gre by
calling ip6_redirect() in ip6gre_err(), as in vti6_err.

Prior to this patch, there's even no route cache generated after
receiving redirect.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>