This change monitors the tx statistics to detect the drop in throughput.
When the throughput drops, the ratio of the actual_ack_count and the expected_
ack_count also drops.  At the same time, the aggregated ba_timeout (the number
of ba timeout retries) also rises.  If the actual_ack_count/expected_ack_count
ratio is 0 and the number of ba timeout retries rises to 16, no tx packets
(tcp, udp, or ping - icmp) can be delivered.  The driver recovers from this
situation by reseting the uCode firmware.  If the actual_ack_count/expected_
ack_count ratio drops below 50% (but not 0) and the aggregated ba_timeout
retries just exceed 5 (but not 16), then the driver can reset the radio to
bring the throughput up.
Signed-off-by: Trieu 'Andrew' Nguyen <trieux.t.nguyen@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

All the queues are awake and ready to use after loading firmware,
for firmware reload case, if any queues was stopped before
reload, mac80211 will wake those queues after restart hardware, so make
sure all the flag used to keep track of the queue status are
reset correctly.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Change pci_alloc_consistent() to dma_alloc_coherent() so we can use
GFP_KERNEL flag.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

While testing the station with the NIC 1000 family, it is found that
the plcp error can easily exceed 50 value in 100mSecs.  This creates
unneccessary radio reset/tuning.  This patch raises the PLCP error
threshold of the NIC 1000 from 50 to 200 error count.
Signed-off-by: Trieu 'Andrew' Nguyen <trieux.t.nguyen@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

To ensure that card is in a sane state during probe we add a reset call.
This change was prompted by users of kdump who was not able to bring up the
wireless driver in the kdump kernel. The problem here was that the primary
kernel, which is not running at the time, left the wireless card up and
running. When the kdump kernel starts it is thus possible to immediately
receive interrupts from firmware after registering interrupt, but without
being ready to deal with interrupts from firmware yet.
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

There is a problem if an "internal short scan" is in progress when a
mac80211 requested scan arrives. If this new scan request arrives within
the "next_scan_jiffies" period then driver will immediately return success
and complete the scan. The problem here is that the scan has not been
fully initialized at this time (is_internal_short_scan is still set to true
because of the currently running scan), which results in the scan
completion never to be sent to mac80211. At this time also, evan though the
internal short scan is still running the state (is_internal_short_scan)
will be set to false, so when the internal scan does complete then mac80211
will receive a scan completion.

Fix this by checking right away if a scan is in progress when a scan
request arrives from mac80211.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Cleanup return values and removes unnecessary code.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Number of calibration op-code are not used by driver, remove those from
iwl-commands.h
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Error checking for aggregation frames should go into aggregation queue,
if aggregation queue not available, use legacy queue instead.
Also make sure the aggregation queue is available to activate,
if driver and mac80211 is out-of-sync, try to disable the queue and
sync-up with mac80211.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Adding function to force reset radio or reload firmware from debugfs.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Provide the function to perform different type of uCode reset/reload operation.
When uCode detect error and can not fix itself, this iwl_force_reset()
function allow driver to perform the necessary reset/reload functions and help
to bring uCode back to normal operation state.

Currently only 2 type of force reset are available:
 - reset radio
 - reload firmware
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Reset and clear all the tx queues when finished downloading runtime
uCode and ready to go into operation mode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

In associated state, when bringing an interface down, existing
BA sessions are torn down. When this is in progress, nothing
prevents mac80211 from accepting another BA session start request.

Use a new station flag to fix this.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add support for using the libertas_tf driver on a managed
or ad-hoc network.
Signed-off-by: Deepak Saxena <dsaxena@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The hardware needs to know what type of frames are being
sent in order to fill in various fields, for example the
timestamp in probe responses (before this patch, it was
always 0).  Set it correctly when initializing the TX
descriptor.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Even if the null data frame is not acked by the AP, mac80211
goes into power save. This might lead to loss of frames
from the AP.
Prevent this by restarting dynamic_ps_timer when ack is not
received for null data frames.

Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The current mac80211 implementation enables power save if there
is no Tx traffic for a specific timeout. Hence, PS is triggered
even if there is a continuous Rx only traffic(like UDP) going on.
This makes the drivers to wait on the tim bit in the next beacon
to awake which leads to redundant sleep-wake cycles.
Fix this by restarting the dynamic ps timer on receiving every
data packet.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rate_control_alloc is not used by anything outside of
ieee80211_init_rate_ctrl_alg.  Both are in rate.c; there's no reason to make
rate_control_alloc visible outside of it.
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes a WARN_ON which is triggered
by Poland's country code.

ath: EEPROM regdomain: 0x8268
ath: EEPROM indicates we should expect a country code
ath: doing EEPROM country->regdmn map search
ath: country maps to regdmn code: 0x37
ath: Country alpha2 being used: PL
ath: Regpair used: 0x37
  -----------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/regd.c:155 ath_regd_init+0x30b
Pid: 12661, comm: firmware/carl91 2.6.33-rc5-wl #18
Call Trace:
 [<>] ? warn_slowpath_common+0x76/0x8c
 [<>] ? ar9170_reg_notifier+0x0/0x2d [carl9170usb]
 [<>] ? ath_regd_init+0x30b/0x377 [ath]
 [<>] ? ar9170_register+0x3b3/0x3ca [carl9170usb]
[...]
---[ end trace ]---

Note: Poland is just an example. But it is very likely
that more country codes are affected.

Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

get_tx_stats() driver operation is not currently used anywhere in mac80211
and there are no plans to use it in the not-so-near future. So it can go
without anyone missing it.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

get_tx_stats() will be removed from mac80211.

Compile-tested only.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

get_tx_stats() will be removed from mac80211.

p54 uses struct ieee80211_tx_queue_stats also internally, so create a new
identical struct p54_tx_queue_stats which the driver can use.

Compile-tested only.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

get_tx_stats() will be removed from mac80211.

Compile-tested only.

Cc: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

get_tx_stats() will be removed from mac80211.

Compile-tested only.

Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

get_tx_stats() will be removed from mac80211.

Compile-tested only.

Cc: Stefano Brivio <stefano.brivio@polimi.it>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

get_tx_stats() will be removed from mac80211.

Compile-tested only.

Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

get_tx_stats() will be removed from mac80211.

Because ar9170 uses ieee80211_tx_queue_stats internally, create a new
identical struct ar9170_tx_queue_stats which the driver can use.

Compile-tested only.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

get_tx_stats() will be removed from mac80211.

mwl8k used struct ieee80211_tx_queue_stats internally to track the queue
lenght. Replace struct ieee80211_tx_queue_stats with a simple len field
in struct mwl8k_tx_queue. Limit and count fields seemed to be unused.

Compile-tested only.

Cc: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

get_tx_stats() will be removed from mac80211.

Compile-tested only.

Cc: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If split tkip key is used, ath_delete_key should delete
rx key and rx mic key. This patch fixes the leak of hw
keycache in the case.
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When userspace requests a deauth while the
authentication work is pending in the auth
(not probe) state, we do not properly abort
the work and then things get confused.

Fix that and also improve the checks here
to include the correct virtual interface,
just in case two virtual interfaces would
ever try to connect to the same BSS.

Also fix a bug -- need to use list_del_rcu
instead of just list_del to free a work
item.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When running directed active scans we currently end up sending both the SSID
probe requests and an additional broadcast one.
This is due to the fact that we always leave the probe request template SSID IE
length to 0. Instead we should set it to the first SSID to scan, and fill the
direct_scan array with the remaining SSIDs to scan for. This way we only send
what we've been asked to: a broadcast probe request when no directed scan is
requested, and directed probe requests otherwise.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Existing iwl6050_ops->iwl6050_hcmd_utils structure had no pointers to chain
noise functions (gain_computation and chain_noise_reset).  As it turns out,
by adding chain_noise_scale (see related patch), there is no need for separate
chain noise function, so simply use iwl6000_ops->iwl5000_hcmd_utils, and
remove those for 6050.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

6x50 device requires a different scaling factor for Rx gain values sent to
device via PHY_CALIBRATION_CMD (CHAIN_NOISE_GAIN_CMD).  Rather than create
a new iwlXXXX_gain_computation() function, add new chain_noise_scale member
to struct iwl_cfg, and keep using iwl5000_gain_computation().
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In AP mode, the only mode where the parameter
is supposed to be valid, we never assign it!
Fix that to allow drivers to avoid parsing
the TIM IE for the value.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This file helps debugging HT channels since it displays if we are on
ht20 or ht40+/ht40-
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Retrying commands seldomly works, most often the firmware is in a
weird state anyway and needs the device to reset. So it's better
to report the broken state back to user-space.

Also rename command_timer_fn() into lbs_cmd_timeout_handler(),
which better reflect it's usage.
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211 uses unit units of 32 usec with txop but wl1251_acx_ac_cfg()
expects it to be usecs. This fortunately didn't cause any severe problems,
only that firmware was using incorrect WMM settings.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>