There is already a SPDX-License-Identifier tag, so the corresponding license
text can be removed.

While at it, be more consistent and:
  - add a missing .c (ff-protocol-latter)
  - remove an empty line (motu-protocol-v1)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/2bfe76c7eeb0f5205a1427e280bf8d9da0354a62.1664110649.git.christophe.jaillet@wanadoo.frSigned-off-by: Takashi Iwai <tiwai@suse.de>

Use __GFP_RETRY_MAYFAIL instead of __GFP__NORETRY in
snd_dma_dev_alloc(), snd_dma_wc_alloc() and friends, to allocate pages
for device memory. The MAYFAIL flag retains the semantics of not
triggering the OOM killer, but lowers the risk of alloc failure.

MAYFAIL flag was added in commit dcda9b04 ("mm, tree wide: replace
__GFP_REPEAT by __GFP_RETRY_MAYFAIL with more useful semantic").

This change addresses recurring failures with SOF audio driver in test
cases where a system suspend-resume stress test is run, combined with an
active high memory-load use-case. The failure typically shows up as:

[ 379.480229] sof-audio-pci-intel-tgl 0000:00:1f.3: booting DSP firmware
[ 379.484803] sof-audio-pci-intel-tgl 0000:00:1f.3: error: memory alloc failed: -12
[ 379.484810] sof-audio-pci-intel-tgl 0000:00:1f.3: error: dma prepare for ICCMAX stream failed

Multiple fixes to reduce the memory usage of DSP boot have been
identified in SOF driver, but even with those fixes, debug on affected
systems has shown that even a single page alloc may fail with
__GFP_NORETRY. When this occurs, system is under significant load on
physical memory, but a lot of reclaimable pages are available, so the
system has not run out of memory. With __GFP_RETRY_MAYFAIL, the errors
are not hit in these stress tests.

The alloc failure is severe as audio capability is completely lost if
alloc failure is hit at system resume.

An alternative solution was considered where the resources for DSP boot
would be kept allocated until driver is unbound. This would avoid the
allocation failure, but consume memory that is only needed temporarily
at probe and resume time. It seems better to not hang on to the memory,
but rather work a bit harder for allocating the pages at resume.

BugLink: https://github.com/thesofproject/linux/issues/3844Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220923153501.3326041-1-kai.vehmanen@linux.intel.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

The current hardware has up to 4 converters. Save little space.
The limit 8 is enough even for a more improved hardware.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20220923082236.61024-1-perex@perex.czSigned-off-by: Takashi Iwai <tiwai@suse.de>

Per discussion on the alsa-devel mailing list [1], the legacy PIN to PCM
device mapping is obsolete nowadays. The maximum number of the simultaneously
usable PCM devices is equal to the HDMI codec converters.

Remove the extra PCM devices (beyond the detected converters) and force
the use of the dynamic PCM device allocation. The legacy code is removed.

I believe that all HDMI codecs have the jack sensing feature. Move the check
to the codec probe function and print a warning, if a codec without this
feature is detected.

[1] https://lore.kernel.org/alsa-devel/2f37e0b2-1e82-8c0b-2bbd-1e5038d6ecc6@perex.cz/

Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20220922084017.25925-1-perex@perex.czSigned-off-by: Takashi Iwai <tiwai@suse.de>

Return the value dsp_allocate_ports() directly instead of storing it in
another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/20220922112846.236987-1-ye.xingchen@zte.com.cnSigned-off-by: Takashi Iwai <tiwai@suse.de>

These two missed IDs need to be added for dynamic selection of drivers.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20220922100014.27080-1-pierre-louis.bossart@linux.intel.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

Merge tag 'asoc-fix-v6.0-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

ASoC: Fixes for v6.0

A few device specific fixes, nothing too large, and a new device
ID for a Dell laptop.

It is useful for the debugging to print also the used HDA codec NIDs
used for the given HDMI device. With the dynamic converter assignment
the converter NID is changed dynamically.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20220921093349.82680-1-perex@perex.czSigned-off-by: Takashi Iwai <tiwai@suse.de>

Make the code more readable.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20220921093322.82609-1-perex@perex.czSigned-off-by: Takashi Iwai <tiwai@suse.de>

We fixed the bug introduced by the patch for managing the shared
clocks at the commit 809f44a0 ("ALSA: usb-audio: Clear fixed clock
rate at closing EP"), but it was merely a workaround.  By this change,
the clock reference rate is cleared at each EP close, hence the still
remaining EP may need a re-setup of rate unnecessarily.

This patch introduces the proper refcounting for the clock reference
object so that the clock setup is done only when needed.

Fixes: 809f44a0 ("ALSA: usb-audio: Clear fixed clock rate at closing EP")
Fixes: c11117b6 ("ALSA: usb-audio: Refcount multiple accesses on the single clock")
Link: https://lore.kernel.org/r/20220920181126.4912-1-tiwai@suse.deSigned-off-by: Takashi Iwai <tiwai@suse.de>

This is a second attempt to fix the bug appearing on Android with the
recent kernel; the first try was ff878b40 and reverted at commit
79764ec7.

The details taken from the v1 patch:

One of the former changes for the endpoint management was the more
consistent setup of endpoints at hw_params.
snd_usb_endpoint_configure() is a single function that does the full
setup, and it's called from both PCM hw_params and prepare callbacks.
Although the EP setup at the prepare phase is usually skipped (by
checking need_setup flag), it may be still effective in some cases
like suspend/resume that requires the interface setup again.

As it's a full and single setup, the invocation of
snd_usb_endpoint_configure() includes not only the USB interface setup
but also the buffer release and allocation.  OTOH, doing the buffer
release and re-allocation at PCM prepare phase is rather superfluous,
and better to be done only in the hw_params phase.

For those optimizations, this patch splits the endpoint setup to two
phases: snd_usb_endpoint_set_params() and snd_usb_endpoint_prepare(),
to be called from hw_params and from prepare, respectively.

Note that this patch changes the driver operation slightly,
effectively moving the USB interface setup again to PCM prepare stage
instead of hw_params stage, while the buffer allocation and such
initializations are still done at hw_params stage.

And, the change of the USB interface setup timing (moving to prepare)
gave an interesting "fix", too: it was reported that the recent
kernels caused silent output at the beginning on playbacks on some
devices on Android, and this change casually fixed the regression.
It seems that those devices are picky about the sample rate change (or
the interface change?), and don't follow the too immediate rate
changes.

Meanwhile, Android operates the PCM in the following order:
- open, then hw_params with the possibly highest sample rate
- close without prepare
- re-open, hw_params with the normal sample rate
- prepare, and start streaming
This procedure ended up the hw_params twice with different rates, and
because the recent kernel did set up the sample rate twice one and
after, it screwed up the device.  OTOH, the earlier kernels didn't set
up the USB interface at hw_params, hence this problem didn't appear.

Now, with this patch, the USB interface setup is again back to the
prepare phase, and it works around the problem automagically.
Although we should address the sample rate problem in a more solid
way in future, let's keep things working as before for now.

***

What's new in the take#2 patch:
- The regression caused by the v1 patch (bko#216500) was due to the
  missing check of need_setup flag at hw_params.  Now the check is
  added, and the snd_usb_endpoint_set_params() call is skipped when
  the running EP is re-opened.

- There was another bug in v1 where the clock reference rate wasn't
  updated at hw_params phase, which may lead to a lack of the proper
  hw constraints when an application doesn't issue the prepare but
  only the hw_params call.  This patch fixes it as well by tracking
  the clock rate change in the prepare callback with a new flag
  "need_update" for the clock reference object, just like others.

- The configure_endpoints() are simplified and folded back into
  snd_usb_pcm_prepare().

Fixes: bf6313a0 ("ALSA: usb-audio: Refactor endpoint management")
Fixes: ff878b40 ("ALSA: usb-audio: Split endpoint setups for hw_params and prepare")
Reported-by: chihhao chen <chihhao.chen@mediatek.com>
Link: https://lore.kernel.org/r/87e6d6ae69d68dc588ac9acc8c0f24d6188375c3.camel@mediatek.com
Link: https://lore.kernel.org/r/20220901124136.4984-1-tiwai@suse.de
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216500
Link: https://lore.kernel.org/r/20220920181106.4894-1-tiwai@suse.deSigned-off-by: Takashi Iwai <tiwai@suse.de>

This reverts commit 32eeeed9.

As the fix for endpoint configuration split is reverted at next, do
another revert here for a clean patch application.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This reverts commit ff878b40.

Unfortunately the recent fix seems bringing another regressions with
PulseAudio / pipewire, at least for Steinberg and MOTU devices.

As a temporary solution, do a straight revert.  The issue for Android
will be revisited again later by another different fix (if any).

Fixes: ff878b40 ("ALSA: usb-audio: Split endpoint setups for hw_params and prepare")
Cc: <stable@vger.kernel.org>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=216500
Link: https://lore.kernel.org/r/20220920113929.25162-1-tiwai@suse.deSigned-off-by: Takashi Iwai <tiwai@suse.de>

Return the value inb() directly instead of storing it in another redundant
 variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/20220920064605.215318-1-ye.xingchen@zte.com.cnSigned-off-by: Takashi Iwai <tiwai@suse.de>

By construction a host and link DMA are always decoupled. This
decoupling happens in the assign() phase. There's no point in checking
if the two parts are decoupled, this is by-design always-true.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20220919121041.43463-9-pierre-louis.bossart@linux.intel.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

The snd_hdac_ext_stream_release() routine uses the bus reg_lock, but
releases it before calling snd_hdac_stream_release() where the bus
reg_lock is taken again.

This creates a timing window where the link stream release could test
an invalid 'opened' boolean status and fail to recouple the host and
link parts.

Fix by exposing a locked version of snd_hdac_stream_release() and use
it without releasing the spinlock.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20220919121041.43463-8-pierre-louis.bossart@linux.intel.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

The logic is needlessly complicated, the basic rule is:

The host streams can be found by checking the 'opened' boolean.
The link streams can be found by checking the 'link_locked' boolean.

Once a stream is found, it can be unconditionally decoupled. The
snd_hdac_ext_stream_decouple_locked() routine will make sure the
register status is modified as needed and the 'decoupled' boolean set.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20220919121041.43463-7-pierre-louis.bossart@linux.intel.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

Minor code reuse, no functionality change.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20220919121041.43463-6-pierre-louis.bossart@linux.intel.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

Make sure there's no ambiguity on layering with the appropriate prefix
added.

Pure rename, no functionality changed.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20220919121041.43463-5-pierre-louis.bossart@linux.intel.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

There are no external users of this helper, move to static and remove
sympol export. No functionality change.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20220919121041.43463-4-pierre-louis.bossart@linux.intel.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

The code in this library is far from self-explanatory, hopefully this
state diagram reverse-engineered from the code will help others
understand the expected transitions.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20220919121041.43463-3-pierre-louis.bossart@linux.intel.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

This helper has no users outside of hdac_stream.c. External users
should only use snd_hdac_stream_start() and snd_hdac_stream_stop().

No functional change beyond making the function static and removing
the symbol export.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20220919121041.43463-2-pierre-louis.bossart@linux.intel.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

Track the converters handling the silent stream using a new
variable to avoid mixing of the open/close and silent stream
use. This change ensures the proper allocation of the converters.

Fixes: 5f80d6bd ("ALSA: hda/hdmi: Fix the converter reuse for the silent stream")
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20220919135444.3554982-1-perex@perex.czSigned-off-by: Takashi Iwai <tiwai@suse.de>

On probe of the ASoC component, the device is reset but the regcache is
retained. This means the regcache gets out of sync if the codec is
rebound to a sound card for a second time. Fix it by reinitializing the
regcache to defaults after the device is reset.

Fixes: b0bcbe61 ("ASoC: tas2770: Fix calling reset in probe")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220919173453.84292-1-povik+lin@cutebit.orgSigned-off-by: Mark Brown <broonie@kernel.org>

On resuming, we anticipate that the jack is detected before playback
or capture. Therefore, we use semaphore to control the jack detection
done without any bothering. During booting, the driver launches jack
detection and releases the semaphore. However, it doesn't perceive the
maniputation of semaphore is not like resuming procedure. This makes
the semaphore's count value become to 2. There is more than one thread
can enter into the critical section. This may get unexpected situation
and make some chaos.
Signed-off-by: SJLIN0 <SJLIN0@nuvoton.com>
Signed-off-by: Wallace Lin <savagecin@gmail.com>
Link: https://lore.kernel.org/r/20220915012800.825196-1-SJLIN0@nuvoton.comSigned-off-by: Mark Brown <broonie@kernel.org>

Yet another SKU that needs a quirk for jack detection and four-speaker
support.

BugLink: https://github.com/thesofproject/linux/issues/3777Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220919114640.42803-1-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

During the code change to add the support for devres-managed card
instance, we put an explicit kfree(card) call at the error path in
snd_card_new().  This is needed for the early error path before the
card is initialized with the device, but is rather superfluous and
causes a double-free at the error path after the card instance is
initialized, as the destructor of the card object already contains a
kfree() call.

This patch fixes the double-free situation by removing the superfluous
kfree().  Meanwhile we need to call kfree() explicitly for the early
error path, so it's added there instead.

Fixes: e8ad415b ("ALSA: core: Add managed card creation")
Reported-by: Rondreis <linhaoguo86@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/CAB7eexL1zBnB636hwS27d-LdPYZ_R1-5fJS_h=ZbCWYU=UPWJg@mail.gmail.com
Link: https://lore.kernel.org/r/20220919123516.28222-1-tiwai@suse.deSigned-off-by: Takashi Iwai <tiwai@suse.de>

Similair to the HP OMEN 15, the HP OMEN 16 also needs
ALC285_FIXUP_HP_MUTE_LED for the mute LED to work.

[ Rearranged the entry in PCI SSID order by tiwai ]
Signed-off-by: Daniel Houldsworth <dhould3@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220918171300.24693-1-dhould3@gmail.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

Use for_each_child_of_node() macro instead of open coding it.
No functional change.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220916141108.683080-1-yangyingliang@huawei.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

When the user space pcm stream uses the silent stream converter,
it is no longer allocated for the silent stream. Clear the appropriate
flag in the hdmi_pcm_open() function. The silent stream setup may
be applied in hdmi_pcm_close() (and the error path - open fcn) again.

If the flag is not cleared, the reuse conditions for the silent
stream converter in hdmi_choose_cvt() may improperly share
this converter.

Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20220913070216.3233974-1-perex@perex.czSigned-off-by: Takashi Iwai <tiwai@suse.de>

The ASUS G15 2022 (GA503R) series laptop has the same node-to-DAC pairs
as early models and the G14, this includes bass speakers which are by
default mapped incorrectly to the 0x06 node.

Add a quirk to use the same DAC pairs as the G14.
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220915080921.35563-4-luke@ljones.devSigned-off-by: Takashi Iwai <tiwai@suse.de>

Fixes up the pincfg for ASUS ROG Strix G15 (G533Z) headphone combo jack

[ Fixed the position in the quirk table by tiwai ]
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220915080921.35563-3-luke@ljones.devSigned-off-by: Takashi Iwai <tiwai@suse.de>

Fixes up the pincfg for ASUS ROG Strix G513 headphone and mic combo jack

[ Fixed the position in the quirk table by tiwai ]
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220915080921.35563-2-luke@ljones.devSigned-off-by: Takashi Iwai <tiwai@suse.de>

A few entries have been mistakenly inserted in wrong positions without
considering the SSID ordering.  Place them at right positions.

Fixes: b7557267 ("ALSA: hda/realtek: Add quirk for ASUS GA402")
Fixes: 94db9cc8 ("ALSA: hda/realtek: Add quirk for ASUS GU603")
Fixes: 739d0959 ("ALSA: hda: Add quirk for ASUS Flow x13")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220915154724.31634-1-tiwai@suse.deSigned-off-by: Takashi Iwai <tiwai@suse.de>

Just as with the 5570 (and the other Dell laptops), this enables the two
subwoofer speakers on the Dell Precision 5530 together with the main
ones, significantly increasing the audio quality. I've tested this
myself on a 5530 and can confirm it's working as expected.
Signed-off-by: Callum Osmotherly <callum.osmotherly@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/YyMjQO3mhyXlMbCf@piranhaSigned-off-by: Takashi Iwai <tiwai@suse.de>

The recent fix in commit 6392dcd1 ("ALSA: usb-audio: Register card
at the last interface") tried to delay the card registration until the
last found interface is probed.  It assumed that the probe callback
gets called for those later interfaces, but it's not always true; as
the driver loops over the descriptor and probes the matching ones,
it's not separately called via multiple probe calls.  This results in
the missing card registration, i.e. no sound device.

For addressing this problem, replace the check whether the last
interface is processed with usb_interface_claimed() instead of the
comparison with the probe interface number.

Fixes: 6392dcd1 ("ALSA: usb-audio: Register card at the last interface")
Link: https://lore.kernel.org/r/20220915085947.7922-1-tiwai@suse.deSigned-off-by: Takashi Iwai <tiwai@suse.de>

The Dell Precision 5570 uses the same 4-speakers-on-ALC289 just like the
previous Precision 5560. I replicated that patch onto this one, and can
confirm that the audio is much better (the woofers are now working);
I've tested it on my Dell Precision 5570.
Signed-off-by: Callum Osmotherly <callum.osmotherly@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/YyGbWM5wEoFMbW2v@piranhaSigned-off-by: Takashi Iwai <tiwai@suse.de>