Add in a gpio-keys section to the Rainier device tree source, add in the
power supply presence GPIOs.
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Fix the size of the Proc VRM card's eeprom used for vpd storage. The
size is changed from 64Kbit to 128Kbit.
Signed-off-by: Jinu Joy Thomas <jinu.joy.thomas@in.ibm.com>
Reviewed-by: Santosh Puranik <santosh.puranik.ibm@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Requesting pinmux configuration is done at driver probe time. The LPC IP
is composed of many sub-devices, each with their own driver, and no
driver exists for the entire IP block. Avoid having each sub-device
request the LPC pinmux by just hogging it in the pinctrl node.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Like most OpenPower machines the VUART is expected to be at /dev/ttyS5
for communication with the host over LPC.
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Added eeproms for the below VPD devices
- BMC
- TPM
- System Planar
- DCM 0 VRM
- DCM 1 VRM
- Base Op panel
- Lcd Op panel
- DASD (All)
- PCIe Cards (All)
Signed-off-by: Jinu Joy Thomas <jinu.joy.thomas@in.ibm.com>
Reviewed-by: Santosh Puranik <santosh.puranik.ibm@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

OpenBMC requires a window the same size as the image being loaded.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>

This adds the description of the Power9 CPUs that are attached to the
BMC.
Signed-off-by: Joel Stanley <joel@jms.id.au>

The UART has an issue on A0 that can be worked around by using the
Synopsis driver.
Tested-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

The UARTs on the AST2600 A0 have a known issue that can be worked around
by using the Synopsys driver.
Tested-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

The AST2600 has five UARTs. Add UART 1 to 4.
Tested-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

The upstream clock for the I2C buses is APB2.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>

We need to ungate RCLK on AST2500- and AST2600-based platforms for RMII
to function. RMII interfaces are commonly used for NCSI.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>

This contains the dt-bindings headers for the ethernet clocks.
Signed-off-by: Joel Stanley <joel@jms.id.au>

Tacoma has two SPI flash devices attached to the FMC, and one on the SPI
controller.
Signed-off-by: Joel Stanley <joel@jms.id.au>

Add fan controllers, regulators, temperature sensors, power supplies
and regulators.
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

The ast2600 has two FSI masters on the APB.
Signed-off-by: Joel Stanley <joel@jms.id.au>

Keep the FMC controller chips at a safe 50 MHz rate and use 100 MHz
for the PNOR on the machines using a AST2500 SoC.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Use the SoC-specific compatible strings instead.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Adds a new power_green led to show the host state.
Signed-off-by: Alexander Filippov <a.filippov@yadro.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Add gpio-keys for various signals on Tacoma.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>

All 2600-evb MACs use RGMII/MDIO.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>

This way enabling the MDIO controllers automatically requests the right
pinmux configuration.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>

The binding was updated to better reflect the intended use of the
hardware and the existing function/groups for SD3 were dropped.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>

The AST2600 u-boot and kernel images have outgrown the OpenBMC layout.
While BMC machines use 128MB SPI NOR chips, we only have 64MB on the EVB
so use a layout that has a smaller region for the ro and rw filesystems.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Tacoma has two SPI flash devices attached to the FMC, and one on the SPI
controller.
Signed-off-by: Joel Stanley <joel@jms.id.au>

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Add fan controllers, regulators, temperature sensors, power supplies
and regulators.
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Rainier contains two NCSI network devices.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Rainier is a new IBM server with POWER host processors and an AST2600
BMC.
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>

This is an alternate layout used by OpenBMC systems that require more
space on the BMC's flash. In addition to more space for the rootfs, it
supports a larger u-boot and Linux kernel FIT image.

The division of space is as follows:

 u-boot + env: 1MB
 kernel/FIT: 9MB
 rwfs: 86MB
 rofs: 32MB
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Change BMC init-ok from GPIO to LED, which needs to blink when BMC
initialization is complete.

Use TAB to align some lines.
Signed-off-by: Chicago Duan <duanzhijia01@inspur.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Enable all the I2C busses on Tacoma and add the I2C slave devices that
exist on the busses.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

This is an AST2600 based BMC card for a Power9 system.
Signed-off-by: Joel Stanley <joel@jms.id.au>

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Everything is the same as G5, except the devices have their own
interrupt now.
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

The AST2600 has two VUART devices.
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>

The AST2600 has 16 I2C buses each with their own global IRQ line.
Signed-off-by: Joel Stanley <joel@jms.id.au>

The AST2600 has 208 normal GPIO pins and 36 1.8V GPIOs.
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Enable the eMMC controller and limit it to 52MHz to avoid the host
controller reporting bus error conditions.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>