When the paths are created in map_singles(), we don't have to
re-create new paths in try_assign_dacs().  Just evaluate the badness
and skip to the next item.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Set path->active flag at the path creation time and let the paths
initialized according to the current path->active state in
set_output_and_unmute().  This allows to modify the active flag of
some output paths dynamically, e.g. switching the front output route
with or without aamix like patch_via.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

activate_amp() in the generic parser checks whether the given NID is
included in any active paths and skips it if found.  This was a
workaround for avoiding disabling the widgets in the active paths when
one path is disabled, thus it shouldn't be applied to the case for
path activation.  Due to this wrong check, some analog loopback paths
haven't been initialized correctly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

... as a preliminary work for migrating patch_sigmatel.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Manage the connection list cache using linked lists instead of
snd_array, and revive snd_hda_get_conn_list() again, so that we don't
have to keep the expanded values locally.
This will reduce the stack usage by recursive call of
snd_hda_get_conn_index() or parse_nid_path() of the generic parser.

The list management doesn't include any mutex protection, thus the
caller needs to take care of race appropriately.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Yet another broken hardware workaround: there are hardware indicating
the inverted jack detection bit result.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Add the new flag, codec->inv_eapd, indicating that the EAPD
implementation is inverted.

There are always broken hardware in the world.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Similar like the implementation in patch_analog.c and patch_via.c,
the generic parser can provide the independent HP PCM stream now.
It's enabled when spec->indep_hp is set by the caller while parsing.

Currently no dynamic PCM switching as in patch_via.c is implemented
yet.  The control returns -EBUSY when the value is changed during PCM
operations.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Allow the path including the loopback mixer widget in the primary
output channel as an alternative in the generic codec parser.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

... instead of numbers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

It never showed the 4th line out and headphone pins since quite ago.
Oh well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Add a better debug print code to show the new assigned paths in
generic parser.  It appears only with CONFIG_SND_DEBUG_VERBOSE=y.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

It's never used in the generic parser.  It was there from the old
Realtek code, which has been dropped quite ago, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

When a PCM name string is generated from the chip name, it might
become strange like "CX20549 (Venice) Analog".  In this patch, the
parser tries to drop the invalid words like "(Venice)" in the PCM name
string.  Also, when the name string is given beforehand by the caller,
respect it and use it as is.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

There is no reason to avoid snd_hda_set_pin_ctl_cache() there.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

When spec->own_eapd_ctl isn't set, try to turn on/off EAPD on demand
for each pin.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

There were some old codes that look not stable enough, which was
derived from the old Realtek code.  The initialization for primary
output in init_multi_out() needs to consider the case of shared DAC.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Just a small clean up by splitting a function.
No functional changes at all.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

For preliminary works to migrate the generic parser for Conexant
codecs: the same function is ported to hda_generic.c.
But now it looks through the jack detect table so that it can cover
better.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Add a flag to indicate whether the vmaster mute hook enum is exposed
or not.  Conexant codecs may want not to expose the control depending
on the model.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

... to distinguish from the invalid event type.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Old codecs like AD1986A tend to have long paths as they were just made
to be the way like AC97.  The current max depth 5 can be too short for
such devices.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The access to a cache array element could be invalid outside the
mutex, so copy locally for the later references.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The dirty entry has to be checked at the beginning in the loop, not in
the inner loop for channels.  This caused a regression that the right
channel isn't properly written.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This would reduce the number of actually executed verbs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

A bit of details won't hurt.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The bound capture volume and switch controls use the cached amp
updates, but it's missing the flushing at the end.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

It makes easier to understand although these are identical with
snd_hda_codec_resume_*() functions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The inverted dmic fix overwrites the right channel amp value, but it
would work only when the amp values have been already actually
written.  Put snd_hda_codec_resume_amp() before the amp write for
flushing caches.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Add an overflow check of CORB in HD-audio controller and codec drivers
so that flood of sequential writes would work properly.
In the controller side, add a check of CORB read-pointer to make
returning -EAGAIN when it's full.  Meanwhile in the codec side, when
-EAGAIN error is received, it retries the write after flushing the
pending verbs (calling get_response() essentially does it).
Signed-off-by: Takashi Iwai <tiwai@suse.de>

These functions are supposed to be called at finishing the cached
sequential writes, so clear the flag properly for lazy developers who
often forget details.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

When verbs or amps are actually written to the hardware, we can clear
dirty flag so that the later snd_hda_codec_resume_*() calls can skip
these verbs / amps.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The commit [2e9bf247: ALSA: hda_codec: Check for invalid zero
connections] trims the whole connection list when an invalid value is
reported by the hardware.  But some codecs (at least AD1986A) may give
a zero NID in the middle of the connection list, so dropping the whole
list isn't good for such cases.

In this patch, as a workaround, allow a single zero NID in the read
connection list.  If it hits zero twice, it's handled as an error, so
that we can avoid "too many connections" errors.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

In general we prefer "Capture Source" to "Input Source".
The latter was chosen in many places just because "Capture Source"
label doesn't work well with the current alsa-lib mixer abstraction
when multiple instances are present.  But when we know that there is a
single input-source element, we can safely choose "Capture Source"
label.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The next migration step is to use the common code in generic driver
for Realtek driver.  This is no drastic change and there should be no
real functional changes, as the generic parser code comes from Realtek
driver originally.

As Realtek driver requires the generic parser code, it needs a
reverse-selection of CONFIG_SND_HDA_GENERIC kconfig.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

These handlers are supposed to be called externally from the codec
drivers once when they need to handle own jack events.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

When no controls are assigned in the parser (e.g. no analog path),
spec->kctls.list is still NULL.  We need to check it before passing to
snd_hda_add_new_ctls().
Signed-off-by: Takashi Iwai <tiwai@suse.de>

In some cases, we want to manipulate the auto_pin_cfg table before
passing to snd_hda_gen_parse_auto_config() (e.g. Realtek SSID check
code fiddles with the headphone pin).   Also passing ignore_pins just
for snd_hda_parse_pin_defcfg() isn't good.

In this patch, snd_hda_gen_parse_auto_config() is changed to receive
the auto_pin_cfg table to be parsed.  The passed auto_pin_cfg table
must have been initialized (typically by calling
snd_hda_gen_parse_auto_config()) beforehand by the caller.

Also together with this change, spec->parse_flags is also removed.
Since this was referred only at the place calling
snd_hda_parse_pin_defcfg(), no longer needed to be kept in spec.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

It may be used in other codec drivers, so let it free.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Enable EAPD in output path initializations automatically unless the
new flag spec->own_eapd_ctl is set.
Signed-off-by: Takashi Iwai <tiwai@suse.de>