Whenever there is no path->ah to the destination, keep only defined
number of skb's. Otherwise there are cases that the driver can keep
infinite list of skb's.

For example, when one device want to send unicast arp to the destination,
and from some reason the SM doesn't respond, the driver currently keeps
all the skb's. If that unicast arp traffic stopped, all  these skb's
are kept by the path object till the interface is down.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

As the result of a completion error the QP can moved to SQE state by
the hardware. Since it's not the Error state, there are no flushes
and hence the driver doesn't know about that.

The fix creates a task that after completion with error which is not a
flush tracks the QP state and if it is in SQE state moves it back to RTS.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Update the cached broadcast record in the priv object after every new
join of this broadcast domain group.

These values are needed for the port configuration (MTU size) and to
all the new multicast (non-broadcast) join requests initial parameters.

For example, SM starts with 2K MTU for all the fabric, and after that it
restarts (or handover to new SM) with new port configuration of 4K MTU.
Without using the new values, the driver will keep its old configuration
of 2K and will not apply the new configuration of 4K.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

The current code in the RX flow uses two sg entries for each incoming
packet, the first one was for the IB headers and the second for the rest
of the data, that causes two  dma map/unmap and two allocations, and few
more actions that were done at the data path.

Use only one linear skb on each incoming packet, for the data (IB
headers and payload), that reduces the packet processing in the
data-path (only one skb, no frags, the first frag was not used anyway,
less memory allocations) and the dma handling (only one dma map/unmap
over each incoming packet instead of two map/unmap per each incoming packet).

After commit 73d3fe6d ("gro: fix aggregation for skb using frag_list") from
Eric Dumazet, we will get full aggregation for large packets.

When running bandwidth tests before and after the (over the card's numa node),
using "netperf -H 1.1.1.3 -T -t TCP_STREAM", the results before are ~12Gbs before
and after ~16Gbs on my setup (Mellanox's ConnectX3).
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

We needed the mcast_mutex when we had to prevent the join completion
callback from having the value it stored in mcast->mc overwritten
by a delayed return from ib_sa_join_multicast.  By storing the return
of ib_sa_join_multicast in an intermediate variable, we prevent a
delayed return from ib_sa_join_multicast overwriting the valid
contents of mcast->mc, and we no longer need a mutex to force the
join callback to run after the return of ib_sa_join_multicast.  This
allows us to do away with the mutex entirely and protect our critical
sections with a just a spinlock instead.  This is highly desirable
as there were some places where we couldn't use a mutex because the
code was not allowed to sleep, and so we were currently using a mix
of mutex and spinlock to protect what we needed to protect.  Now we
only have a spin lock and the locking complexity is greatly reduced.
Signed-off-by: Doug Ledford <dledford@redhat.com>

Allow the ipoib layer to attempt to join all outstanding multicast
groups at once.  The ib_sa layer will serialize multiple attempts to
join the same group, but will process attempts to join different groups
in parallel.  Take advantage of that.

In order to make this happen, change the mcast_join_thread to loop
through all needed joins, sending a join request for each one that we
still need to join.  There are a few special cases we handle though:

1) Don't attempt to join anything but the broadcast group until the join
of the broadcast group has succeeded.
2) No longer restart the join task at the end of completion handling.
If we completed successfully, we are done.  The join task now needs kicked
either by mcast_send or mcast_restart_task or mcast_start_thread, but
should not need started anytime else except when scheduling a backoff
attempt to rejoin.
3) No longer use separate join/completion routines for regular and
sendonly joins, pass them all through the same routine and just do the
right thing based on the SENDONLY join flag.
4) Only try to join a SENDONLY join twice, then drop the packets and
quit trying.  We leave the mcast group in the list so that if we get a
new packet, all that we have to do is queue up the packet and restart
the join task and it will automatically try to join twice and then
either send or flush the queue again.
Signed-off-by: Doug Ledford <dledford@redhat.com>

Commit a9c8ba58 ("IPoIB: Fix usage of uninitialized multicast
objects") added a new flag MCAST_JOIN_STARTED, but was not very strict
in how it was used.  We didn't always initialize the completion struct
before we set the flag, and we didn't always call complete on the
completion struct from all paths that complete it.  And when we did
complete it, sometimes we continued to touch the mcast entry after
the completion, opening us up to possible use after free issues.

This made it less than totally effective, and certainly made its use
confusing.  And in the flush function we would use the presence of this
flag to signal that we should wait on the completion struct, but we never
cleared this flag, ever.

In order to make things clearer and aid in resolving the rtnl deadlock
bug I've been chasing, I cleaned this up a bit.

 1) Remove the MCAST_JOIN_STARTED flag entirely
 2) Change MCAST_FLAG_BUSY so it now only means a join is in-flight
 3) Test mcast->mc directly to see if we have completed
    ib_sa_join_multicast (using IS_ERR_OR_NULL)
 4) Make sure that before setting MCAST_FLAG_BUSY we always initialize
    the mcast->done completion struct
 5) Make sure that before calling complete(&mcast->done), we always clear
    the MCAST_FLAG_BUSY bit
 6) Take the mcast_mutex before we call ib_sa_multicast_join and also
    take the mutex in our join callback.  This forces
    ib_sa_multicast_join to return and set mcast->mc before we process
    the callback.  This way, our callback can safely clear mcast->mc
    if there is an error on the join and we will do the right thing as
    a result in mcast_dev_flush.
 7) Because we need the mutex to synchronize mcast->mc, we can no
    longer call mcast_sendonly_join directly from mcast_send and
    instead must add sendonly join processing to the mcast_join_task
 8) Make MCAST_RUN mean that we have a working mcast subsystem, not that
    we have a running task.  We know when we need to reschedule our
    join task thread and don't need a flag to tell us.
 9) Add a helper for rescheduling the join task thread

A number of different races are resolved with these changes.  These
races existed with the old MCAST_FLAG_BUSY usage, the
MCAST_JOIN_STARTED flag was an attempt to address them, and while it
helped, a determined effort could still trip things up.

One race looks something like this:

Thread 1                             Thread 2
ib_sa_join_multicast (as part of running restart mcast task)
  alloc member
  call callback
                                     ifconfig ib0 down
				     wait_for_completion
    callback call completes
                                     wait_for_completion in
				     mcast_dev_flush completes
				       mcast->mc is PTR_ERR_OR_NULL
				       so we skip ib_sa_leave_multicast
    return from callback
  return from ib_sa_join_multicast
set mcast->mc = return from ib_sa_multicast

We now have a permanently unbalanced join/leave issue that trips up the
refcounting in core/multicast.c

Another like this:

Thread 1                   Thread 2         Thread 3
ib_sa_multicast_join
                                            ifconfig ib0 down
					    priv->broadcast = NULL
                           join_complete
			                    wait_for_completion
			   mcast->mc is not yet set, so don't clear
return from ib_sa_join_multicast and set mcast->mc
			   complete
			   return -EAGAIN (making mcast->mc invalid)
			   		    call ib_sa_multicast_leave
					    on invalid mcast->mc, hang
					    forever

By holding the mutex around ib_sa_multicast_join and taking the mutex
early in the callback, we force mcast->mc to be valid at the time we
run the callback.  This allows us to clear mcast->mc if there is an
error and the join is going to fail.  We do this before we complete
the mcast.  In this way, mcast_dev_flush always sees consistent state
in regards to mcast->mc membership at the time that the
wait_for_completion() returns.
Signed-off-by: Doug Ledford <dledford@redhat.com>

Various places in the IPoIB code had a deadlock related to flushing
the ipoib workqueue.  Now that we have per device workqueues and a
specific flush workqueue, there is no longer a deadlock issue with
flushing the device specific workqueues and we can do so unilaterally.
Signed-off-by: Doug Ledford <dledford@redhat.com>

During my recent work on the rtnl lock deadlock in the IPoIB driver, I
saw that even once I fixed the apparent races for a single device, as
soon as that device had any children, new races popped up.  It turns
out that this is because no matter how well we protect against races
on a single device, the fact that all devices use the same workqueue,
and flush_workqueue() flushes *everything* from that workqueue means
that we would also have to prevent all races between different devices
(for instance, ipoib_mcast_restart_task on interface ib0 can race with
ipoib_mcast_flush_dev on interface ib0.8002, resulting in a deadlock on
the rtnl_lock).

There are several possible solutions to this problem:

Make carrier_on_task and mcast_restart_task try to take the rtnl for
some set period of time and if they fail, then bail.  This runs the
real risk of dropping work on the floor, which can end up being its
own separate kind of deadlock.

Set some global flag in the driver that says some device is in the
middle of going down, letting all tasks know to bail.  Again, this can
drop work on the floor.

Or the method this patch attempts to use, which is when we bring an
interface up, create a workqueue specifically for that interface, so
that when we take it back down, we are flushing only those tasks
associated with our interface.  In addition, keep the global
workqueue, but now limit it to only flush tasks.  In this way, the
flush tasks can always flush the device specific work queues without
having deadlock issues.
Signed-off-by: Doug Ledford <dledford@redhat.com>

We blindly assume that we can just take the rtnl lock and that will
prevent races with downing this interface.  Unfortunately, that's not
the case.  In ipoib_mcast_stop_thread() we will call flush_workqueue()
in an attempt to clear out all remaining instances of ipoib_join_task.
But, since this task is put on the same workqueue as the join task,
the flush_workqueue waits on this thread too.  But this thread is
deadlocked on the rtnl lock.  The better thing here is to use trylock
and loop on that until we either get the lock or we see that
FLAG_OPER_UP has been cleared, in which case we don't need to do
anything anyway and we just return.

While investigating which flag should be used, FLAG_ADMIN_UP or
FLAG_OPER_UP, it was determined that FLAG_OPER_UP was the more
appropriate flag to use.  However, there was a mix of these two flags in
use in the existing code.  So while we check for that flag here as part
of this race fix, also cleanup the two places that had used the less
appropriate flag for their tests.
Signed-off-by: Doug Ledford <dledford@redhat.com>

The ipoib_mcast_flush_dev routine is called with the rtnl_lock held and
needs to keep it held.  It also needs to call flush_workqueue() to flush
out any outstanding work.  In the past, we've had to try and make sure
that we didn't flush out any outstanding join completions because they
also wanted to grab rtnl_lock() and that would deadlock.  It turns out
that the only thing in the join completion handler that needs this lock
can be safely moved to our carrier_on_task, thereby reducing the
potential for the join completion code and the flush code to deadlock
against each other.
Signed-off-by: Doug Ledford <dledford@redhat.com>

In preparation for using per device work queues, we need to move the
start of the neighbor thread task to after ipoib_ib_dev_init and move
the destruction of the neighbor task to before ipoib_ib_dev_cleanup.
Otherwise we will end up freeing our workqueue with work possibly
still on it.
Signed-off-by: Doug Ledford <dledford@redhat.com>

Create a an ipoib_flush_ah and ipoib_stop_ah routines to use at
appropriate times to flush out all remaining ah entries before we shut
the device down.

Because neighbors and mcast entries can each have a reference on any
given ah, we must make sure to free all of those first before our ah
will actually have a 0 refcount and be able to be reaped.

This factoring is needed in preparation for having per-device work
queues.  The original per-device workqueue code resulted in the following
error message:

<ibdev>: ib_dealloc_pd failed

That error was tracked down to this issue.  With the changes to which
workqueues were flushed when, there were no flushes of the per device
workqueue after the last ah's were freed, resulting in an attempt to
dealloc the pd with outstanding resources still allocated.  This code
puts the explicit flushes in the needed places to avoid that problem.
Signed-off-by: Doug Ledford <dledford@redhat.com>

Pull kconfig updates from Michal Marek:
 "Here is the kconfig stuff for v4.1-rc1:

   - fixes for mergeconfig (used by make kvmconfig/tinyconfig)

   - header cleanup

   - make -s *config is silent now"

* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  kconfig: Do not print status messages in make -s mode
  kconfig: Simplify Makefile
  kbuild: add generic mergeconfig target, %.config
  merge_config.sh: rename MAKE to RUNMAKE
  merge_config.sh: improve indentation
  kbuild: mergeconfig: remove redundant $(objtree)
  kbuild: mergeconfig: move an error check to merge_config.sh
  kbuild: mergeconfig: fix "jobserver unavailable" warning
  kconfig: Remove unnecessary prototypes from headers
  kconfig: Remove dead code
  kconfig: Get rid of the P() macro in headers
  kconfig: fix a misspelling in scripts/kconfig/merge_config.sh

Pull kbuild updates from Michal Marek:
 "Here is the first round of kbuild changes for v4.1-rc1:

   - kallsyms fix for ARM and cleanup

   - make dep(end) removed (developers have no sense of nostalgia these
     days...)

   - include Makefiles by relative path

   - stop useless rebuilds of asm-offsets.h and bounds.h"

* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  Kbuild: kallsyms: drop special handling of pre-3.0 GCC symbols
  Kbuild: kallsyms: ignore veneers emitted by the ARM linker
  kbuild: ia64: use $(src)/Makefile.gate rather than particular path
  kbuild: include $(src)/Makefile rather than $(obj)/Makefile
  kbuild: use relative path more to include Makefile
  kbuild: use relative path to include Makefile
  kbuild: do not add $(bounds-file) and $(offsets-file) to targets
  kbuild: remove warning about "make depend"
  kbuild: Don't reset timestamps in include/generated if not needed

Pull security subsystem updates from James Morris:
 "Highlights for this window:

   - improved AVC hashing for SELinux by John Brooks and Stephen Smalley

   - addition of an unconfined label to Smack

   - Smack documentation update

   - TPM driver updates"

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (28 commits)
  lsm: copy comm before calling audit_log to avoid race in string printing
  tomoyo: Do not generate empty policy files
  tomoyo: Use if_changed when generating builtin-policy.h
  tomoyo: Use bin2c to generate builtin-policy.h
  selinux: increase avtab max buckets
  selinux: Use a better hash function for avtab
  selinux: convert avtab hash table to flex_array
  selinux: reconcile security_netlbl_secattr_to_sid() and mls_import_netlbl_cat()
  selinux: remove unnecessary pointer reassignment
  Smack: Updates for Smack documentation
  tpm/st33zp24/spi: Add missing device table for spi phy.
  tpm/st33zp24: Add proper wait for ordinal duration in case of irq mode
  smack: Fix gcc warning from unused smack_syslog_lock mutex in smackfs.c
  Smack: Allow an unconfined label in bringup mode
  Smack: getting the Smack security context of keys
  Smack: Assign smack_known_web as default smk_in label for kernel thread's socket
  tpm/tpm_infineon: Use struct dev_pm_ops for power management
  MAINTAINERS: Add Jason as designated reviewer for TPM
  tpm: Update KConfig text to include TPM2.0 FIFO chips
  tpm/st33zp24/dts/st33zp24-spi: Add dts documentation for st33zp24 spi phy
  ...

Pull crypto update from Herbert Xu:
 "Here is the crypto update for 4.1:

  New interfaces:
   - user-space interface for AEAD
   - user-space interface for RNG (i.e., pseudo RNG)

  New hashes:
   - ARMv8 SHA1/256
   - ARMv8 AES
   - ARMv8 GHASH
   - ARM assembler and NEON SHA256
   - MIPS OCTEON SHA1/256/512
   - MIPS img-hash SHA1/256 and MD5
   - Power 8 VMX AES/CBC/CTR/GHASH
   - PPC assembler AES, SHA1/256 and MD5
   - Broadcom IPROC RNG driver

  Cleanups/fixes:
   - prevent internal helper algos from being exposed to user-space
   - merge common code from assembly/C SHA implementations
   - misc fixes"

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (169 commits)
  crypto: arm - workaround for building with old binutils
  crypto: arm/sha256 - avoid sha256 code on ARMv7-M
  crypto: x86/sha512_ssse3 - move SHA-384/512 SSSE3 implementation to base layer
  crypto: x86/sha256_ssse3 - move SHA-224/256 SSSE3 implementation to base layer
  crypto: x86/sha1_ssse3 - move SHA-1 SSSE3 implementation to base layer
  crypto: arm64/sha2-ce - move SHA-224/256 ARMv8 implementation to base layer
  crypto: arm64/sha1-ce - move SHA-1 ARMv8 implementation to base layer
  crypto: arm/sha2-ce - move SHA-224/256 ARMv8 implementation to base layer
  crypto: arm/sha256 - move SHA-224/256 ASM/NEON implementation to base layer
  crypto: arm/sha1-ce - move SHA-1 ARMv8 implementation to base layer
  crypto: arm/sha1_neon - move SHA-1 NEON implementation to base layer
  crypto: arm/sha1 - move SHA-1 ARM asm implementation to base layer
  crypto: sha512-generic - move to generic glue implementation
  crypto: sha256-generic - move to generic glue implementation
  crypto: sha1-generic - move to generic glue implementation
  crypto: sha512 - implement base layer for SHA-512
  crypto: sha256 - implement base layer for SHA-256
  crypto: sha1 - implement base layer for SHA-1
  crypto: api - remove instance when test failed
  crypto: api - Move alg ref count init to crypto_check_alg
  ...

Pull networking updates from David Miller:

 1) Add BQL support to via-rhine, from Tino Reichardt.

 2) Integrate SWITCHDEV layer support into the DSA layer, so DSA drivers
    can support hw switch offloading.  From Floria Fainelli.

 3) Allow 'ip address' commands to initiate multicast group join/leave,
    from Madhu Challa.

 4) Many ipv4 FIB lookup optimizations from Alexander Duyck.

 5) Support EBPF in cls_bpf classifier and act_bpf action, from Daniel
    Borkmann.

 6) Remove the ugly compat support in ARP for ugly layers like ax25,
    rose, etc.  And use this to clean up the neigh layer, then use it to
    implement MPLS support.  All from Eric Biederman.

 7) Support L3 forwarding offloading in switches, from Scott Feldman.

 8) Collapse the LOCAL and MAIN ipv4 FIB tables when possible, to speed
    up route lookups even further.  From Alexander Duyck.

 9) Many improvements and bug fixes to the rhashtable implementation,
    from Herbert Xu and Thomas Graf.  In particular, in the case where
    an rhashtable user bulk adds a large number of items into an empty
    table, we expand the table much more sanely.

10) Don't make the tcp_metrics hash table per-namespace, from Eric
    Biederman.

11) Extend EBPF to access SKB fields, from Alexei Starovoitov.

12) Split out new connection request sockets so that they can be
    established in the main hash table.  Much less false sharing since
    hash lookups go direct to the request sockets instead of having to
    go first to the listener then to the request socks hashed
    underneath.  From Eric Dumazet.

13) Add async I/O support for crytpo AF_ALG sockets, from Tadeusz Struk.

14) Support stable privacy address generation for RFC7217 in IPV6.  From
    Hannes Frederic Sowa.

15) Hash network namespace into IP frag IDs, also from Hannes Frederic
    Sowa.

16) Convert PTP get/set methods to use 64-bit time, from Richard
    Cochran.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1816 commits)
  fm10k: Bump driver version to 0.15.2
  fm10k: corrected VF multicast update
  fm10k: mbx_update_max_size does not drop all oversized messages
  fm10k: reset head instead of calling update_max_size
  fm10k: renamed mbx_tx_dropped to mbx_tx_oversized
  fm10k: update xcast mode before synchronizing multicast addresses
  fm10k: start service timer on probe
  fm10k: fix function header comment
  fm10k: comment next_vf_mbx flow
  fm10k: don't handle mailbox events in iov_event path and always process mailbox
  fm10k: use separate workqueue for fm10k driver
  fm10k: Set PF queues to unlimited bandwidth during virtualization
  fm10k: expose tx_timeout_count as an ethtool stat
  fm10k: only increment tx_timeout_count in Tx hang path
  fm10k: remove extraneous "Reset interface" message
  fm10k: separate PF only stats so that VF does not display them
  fm10k: use hw->mac.max_queues for stats
  fm10k: only show actual queues, not the maximum in hardware
  fm10k: allow creation of VLAN on default vid
  fm10k: fix unused warnings
  ...

Pull ARM updates from Russell King:
 "Included in this update are both some long term fixes and some new
  features.

  Fixes:

   - An integer overflow in the calculation of ELF_ET_DYN_BASE.

   - Avoiding OOMs for high-order IOMMU allocations

   - SMP requires the data cache to be enabled for synchronisation
     primitives to work, so prevent the CPU_DCACHE_DISABLE option being
     visible on SMP builds.

   - A bug going back 10+ years in the noMMU ARM94* CPU support code,
     where it corrupts registers.  Found by folk getting Linux running
     on their cameras.

   - Versatile Express needs an errata workaround enabled for CPU
     hot-unplug to work.

  Features:

   - Clean up module linker by handling out of range relocations
     separately from relocation cases we don't handle.

   - Fix a long term bug in the pci_mmap_page_range() code, which we
     hope won't impact userspace (we hope there's no users of the
     existing broken interface.)

   - Don't map DMA coherent allocations when we don't have a MMU.

   - Drop experimental status for SMP_ON_UP.

   - Warn when DT doesn't specify ePAPR mandatory cache properties.

   - Add documentation concerning how we find the start of physical
     memory for AUTO_ZRELADDR kernels, detailing why we have chosen the
     mask and the implications of changing it.

   - Updates from Ard Biesheuvel to address some issues with large
     kernels (such as allyesconfig) failing to link.

   - Allow hibernation to work on modern (ARMv7) CPUs - this appears to
     have never worked in the past on these CPUs.

   - Enable IRQ_SHOW_LEVEL, which changes the /proc/interrupts output
     format (hopefully without userspace breaking...  let's hope that if
     it causes someone a problem, they tell us.)

   - Fix tegra-ahb DT offsets.

   - Rework ARM errata 643719 code (and ARMv7 flush_cache_louis()/
     flush_dcache_all()) code to be more efficient, and enable this
     errata workaround by default for ARMv7+SMP CPUs.  This complements
     the Versatile Express fix above.

   - Rework ARMv7 context code for errata 430973, so that only Cortex A8
     CPUs are impacted by the branch target buffer flush when this
     errata is enabled.  Also update the help text to indicate that all
     r1p* A8 CPUs are impacted.

   - Switch ARM to the generic show_mem() implementation, it conveys all
     the information which we were already reporting.

   - Prevent slow timer sources being used for udelay() - timers running
     at less than 1MHz are not useful for this, and can cause udelay()
     to return immediately, without any wait.  Using such a slow timer
     is silly.

   - VDSO support for 32-bit ARM, mainly for gettimeofday() using the
     ARM architected timer.

   - Perf support for Scorpion performance monitoring units"

vdso semantic conflict fixed up as per linux-next.

* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (52 commits)
  ARM: update errata 430973 documentation to cover Cortex A8 r1p*
  ARM: ensure delay timer has sufficient accuracy for delays
  ARM: switch to use the generic show_mem() implementation
  ARM: proc-v7: avoid errata 430973 workaround for non-Cortex A8 CPUs
  ARM: enable ARM errata 643719 workaround by default
  ARM: cache-v7: optimise test for Cortex A9 r0pX devices
  ARM: cache-v7: optimise branches in v7_flush_cache_louis
  ARM: cache-v7: consolidate initialisation of cache level index
  ARM: cache-v7: shift CLIDR to extract appropriate field before masking
  ARM: cache-v7: use movw/movt instructions
  ARM: allow 16-bit instructions in ALT_UP()
  ARM: proc-arm94*.S: fix setup function
  ARM: vexpress: fix CPU hotplug with CT9x4 tile.
  ARM: 8276/1: Make CPU_DCACHE_DISABLE depend on !SMP
  ARM: 8335/1: Documentation: DT bindings: Tegra AHB: document the legacy base address
  ARM: 8334/1: amba: tegra-ahb: detect and correct bogus base address
  ARM: 8333/1: amba: tegra-ahb: fix register offsets in the macros
  ARM: 8339/1: Enable CONFIG_GENERIC_IRQ_SHOW_LEVEL
  ARM: 8338/1: kexec: Relax SMP validation to improve DT compatibility
  ARM: 8337/1: mm: Do not invoke OOM for higher order IOMMU DMA allocations
  ...

Pull s390 updates from Martin Schwidefsky:
 "The major change in this merge is the removal of the support for
  31-bit kernels.  Naturally 31-bit user space will continue to work via
  the compat layer.

  And then some cleanup, some improvements and bug fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (23 commits)
  s390/smp: wait until secondaries are active & online
  s390/hibernate: fix save and restore of kernel text section
  s390/cacheinfo: add missing facility check
  s390/syscalls: simplify syscall_get_arch()
  s390/irq: enforce correct irqclass_sub_desc array size
  s390: remove "64" suffix from mem64.S and swsusp_asm64.S
  s390/ipl: cleanup macro usage
  s390/ipl: cleanup shutdown_action attributes
  s390/ipl: cleanup bin attr usage
  s390/uprobes: fix address space annotation
  s390: add missing arch_release_task_struct() declaration
  s390: make couple of functions and variables static
  s390/maccess: improve s390_kernel_write()
  s390/maccess: remove potentially broken probe_kernel_write()
  s390/watchdog: support for KVM hypervisors and delete pr_info messages
  s390/watchdog: enable KEEPALIVE for /dev/watchdog
  s390/dasd: remove setting of scheduler from driver
  s390/traps: panic() instead of die() on translation exception
  s390: remove test_facility(2) (== z/Architecture mode active) checks
  s390/cmpxchg: simplify cmpxchg_double
  ...

Pull power management and ACPI updates from Rafael Wysocki:
 "These are mostly fixes and cleanups all over, although there are a few
  items that sort of fall into the new feature category.

  First off, we have new callbacks for PM domains that should help us to
  handle some issues related to device initialization in a better way.

  There also is some consolidation in the unified device properties API
  area allowing us to use that inferface for accessing data coming from
  platform initialization code in addition to firmware-provided data.

  We have some new device/CPU IDs in a few drivers, support for new
  chips and a new cpufreq driver too.

  Specifics:

   - Generic PM domains support update including new PM domain callbacks
     to handle device initialization better (Russell King, Rafael J
     Wysocki, Kevin Hilman)

   - Unified device properties API update including a new mechanism for
     accessing data provided by platform initialization code (Rafael J
     Wysocki, Adrian Hunter)

   - ARM cpuidle update including ARM32/ARM64 handling consolidation
     (Daniel Lezcano)

   - intel_idle update including support for the Silvermont Core in the
     Baytrail SOC and for the Airmont Core in the Cherrytrail and
     Braswell SOCs (Len Brown, Mathias Krause)

   - New cpufreq driver for Hisilicon ACPU (Leo Yan)

   - intel_pstate update including support for the Knights Landing chip
     (Dasaratharaman Chandramouli, Kristen Carlson Accardi)

   - QorIQ cpufreq driver update (Tang Yuantian, Arnd Bergmann)

   - powernv cpufreq driver update (Shilpasri G Bhat)

   - devfreq update including Tegra support changes (Tomeu Vizoso,
     MyungJoo Ham, Chanwoo Choi)

   - powercap RAPL (Running-Average Power Limit) driver update including
     support for Intel Broadwell server chips (Jacob Pan, Mathias Krause)

   - ACPI device enumeration update related to the handling of the
     special PRP0001 device ID allowing DT-style 'compatible' property
     to be used for ACPI device identification (Rafael J Wysocki)

   - ACPI EC driver update including limited _DEP support (Lan Tianyu,
     Lv Zheng)

   - ACPI backlight driver update including a new mechanism to allow
     native backlight handling to be forced on non-Windows 8 systems and
     a new quirk for Lenovo Ideapad Z570 (Aaron Lu, Hans de Goede)

   - New Windows Vista compatibility quirk for Sony VGN-SR19XN (Chen Yu)

   - Assorted ACPI fixes and cleanups (Aaron Lu, Martin Kepplinger,
     Masanari Iida, Mika Westerberg, Nan Li, Rafael J Wysocki)

   - Fixes related to suspend-to-idle for the iTCO watchdog driver and
     the ACPI core system suspend/resume code (Rafael J Wysocki, Chen Yu)

   - PM tracing support for the suspend phase of system suspend/resume
     transitions (Zhonghui Fu)

   - Configurable delay for the system suspend/resume testing facility
     (Brian Norris)

   - PNP subsystem cleanups (Peter Huewe, Rafael J Wysocki)"

* tag 'pm+acpi-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (74 commits)
  ACPI / scan: Fix NULL pointer dereference in acpi_companion_match()
  ACPI / scan: Rework modalias creation when "compatible" is present
  intel_idle: mark cpu id array as __initconst
  powercap / RAPL: mark rapl_ids array as __initconst
  powercap / RAPL: add ID for Broadwell server
  intel_pstate: Knights Landing support
  intel_pstate: remove MSR test
  cpufreq: fix qoriq uniprocessor build
  ACPI / scan: Take the PRP0001 position in the list of IDs into account
  ACPI / scan: Simplify acpi_match_device()
  ACPI / scan: Generalize of_compatible matching
  device property: Introduce firmware node type for platform data
  device property: Make it possible to use secondary firmware nodes
  PM / watchdog: iTCO: stop watchdog during system suspend
  cpufreq: hisilicon: add acpu driver
  ACPI / EC: Call acpi_walk_dep_device_list() after installing EC opregion handler
  cpufreq: powernv: Report cpu frequency throttling
  intel_idle: Add support for the Airmont Core in the Cherrytrail and Braswell SOCs
  intel_idle: Update support for Silvermont Core in Baytrail SOC
  PM / devfreq: tegra: Register governor on module init
  ...

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2015-04-14

This series contains updates to fm10k only.

Fixed transmit statistics which was actually using values from the
receive ring, instead of the transmit ring.  Fixed up spelling mistakes
in code comments and resolved unused argument warnings.  Added support
for netconsole.  Fixed up statistic reporting so that we are only
reporting from actual queues as well as display PF only stats for
just the PF and not the VF.  Also fixed an issue that when returning
virtualization queues from the VF back to the PF, we were retaining
the VF rate limiter.

Fixed up the driver to use a separate workqueue, which helps reduce
and stabilize latency between scheduling the work in our interrupt and
actually performing the work.

Fixed a bug where the VF tried to set a multicast address before
requesting the required xcast mode.

Fix VF multicast update since VFs were being improperly added to the
switch's mutlicast group.  The error stems from the fact that incorrect
arguments were passed to the update_mc_addr().

Thanks to Alex Duyck for the extensive review.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull input subsystem updates from Dmitry Torokhov:
 "You will get the following new drivers:

   - Qualcomm PM8941 power key drver
   - ChipOne icn8318 touchscreen controller driver
   - Broadcom iProc touchscreen and keypad drivers
   - Semtech SX8654 I2C touchscreen controller driver

  ALPS driver now supports newer SS4 devices; Elantech got a fix that
  should make it work on some ASUS laptops; and a slew of other
  enhancements and random fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (51 commits)
  Input: alps - non interleaved V2 dualpoint has separate stick button bits
  Input: alps - fix touchpad buttons getting stuck when used with trackpoint
  Input: atkbd - document "no new force-release quirks" policy
  Input: ALPS - make alps_get_pkt_id_ss4_v2() and others static
  Input: ALPS - V7 devices can report 5-finger taps
  Input: ALPS - add support for SS4 touchpad devices
  Input: ALPS - refactor alps_set_abs_params_mt()
  Input: elantech - fix absolute mode setting on some ASUS laptops
  Input: atmel_mxt_ts - split out touchpad initialisation logic
  Input: atmel_mxt_ts - implement support for T100 touch object
  Input: cros_ec_keyb - fix clearing keyboard state on wakeup
  Input: gscps2 - drop pci_ids dependency
  Input: synaptics - allocate 3 slots to keep stability in image sensors
  Input: Revert "Revert "synaptics - use dmax in input_mt_assign_slots""
  Input: MT - make slot assignment work for overcovered solutions
  mfd: tc3589x: enforce device-tree only mode
  Input: tc3589x - localize platform data
  Input: tsc2007 - Convert msecs to jiffies only once
  Input: edt-ft5x06 - remove EV_SYN event report
  Input: edt-ft5x06 - allow to setting the maximum axes value through the DT
  ...

Pull i2c updates from Wolfram Sang:
 "Most notable:

   - introducing the i2c_quirk infrastructure.  Now, flaws of I2C
     controllers can be described and the core will check if the flaws
     collide with the messages to be sent

   - wait_for_completion return type cleanup series

   - new drivers for Digicolor, Netlogic XLP, Ingenic JZ4780

   - updates to the I2C slave framework which include API changes.  Its
     only user was updated, too.  Documentation was finally added

   - changed dynamic bus numbering for the DT case.  This could change
     bus numbers for users.  However, it fixes a collision where dynamic
     and static busses request the same id.

   - driver bugfixes, cleanups"

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (52 commits)
  i2c: xlp9xx: Driver for Netlogic XLP9XX/5XX I2C controller
  of: Add vendor prefix 'netlogic'
  i2c: davinci: use ICPFUNC to toggle I2C as gpio for bus recovery
  i2c: davinci: use bus recovery infrastructure
  i2c: change input parameter to i2c_adapter for prepare/unprepare_recovery
  i2c: i2c-mux-gpio: remove error messages for probe deferrals
  i2c: jz4780: Add i2c bus controller driver for Ingenic JZ4780
  i2c: dln2: set the device tree node of the adapter
  i2c: davinci: fixup wait_for_completion_timeout handling
  i2c: mpc: Fix ISR return value
  i2c: slave-eeprom: add more info when to increase the pointer
  i2c: slave: add documentation for i2c-slave-eeprom
  Documentation: i2c: describe the new slave mode
  i2c: slave: rework the slave API
  i2c: add support for the Digicolor I2C controller
  i2c: busses with dynamic ids should start after fixed ids for DT
  of: base: add function to get highest id of an alias stem
  i2c: designware: Suppress error message if platform_get_irq() < 0
  i2c: mpc: assign the correct prescaler from SVR
  i2c: img-scb: fixup of wait_for_completion_timeout return handling
  ...

Pull VFIO updates from Alex Williamson:

 - VFIO platform bus driver support (Baptiste Reynal, Antonios Motakis,
   testing and review by Eric Auger)

 - Split VFIO irqfd support to separate module (Alex Williamson)

 - vfio-pci VGA arbiter client (Alex Williamson)

 - New vfio-pci.ids= module option (Alex Williamson)

 - vfio-pci D3 power state support for idle devices (Alex Williamson)

* tag 'vfio-v4.1-rc1' of git://github.com/awilliam/linux-vfio: (30 commits)
  vfio-pci: Fix use after free
  vfio-pci: Move idle devices to D3hot power state
  vfio-pci: Remove warning if try-reset fails
  vfio-pci: Allow PCI IDs to be specified as module options
  vfio-pci: Add VGA arbiter client
  vfio-pci: Add module option to disable VGA region access
  vgaarb: Stub vga_set_legacy_decoding()
  vfio: Split virqfd into a separate module for vfio bus drivers
  vfio: virqfd_lock can be static
  vfio: put off the allocation of "minor" in vfio_create_group
  vfio/platform: implement IRQ masking/unmasking via an eventfd
  vfio: initialize the virqfd workqueue in VFIO generic code
  vfio: move eventfd support code for VFIO_PCI to a separate file
  vfio: pass an opaque pointer on virqfd initialization
  vfio: add local lock for virqfd instead of depending on VFIO PCI
  vfio: virqfd: rename vfio_pci_virqfd_init and vfio_pci_virqfd_exit
  vfio: add a vfio_ prefix to virqfd_enable and virqfd_disable and export
  vfio/platform: support for level sensitive interrupts
  vfio/platform: trigger an interrupt via eventfd
  vfio/platform: initial interrupts support code
  ...

Pull pincontrol updates from Linus Walleij:
 "This is the bulk of pin control changes for the v4.1 development
  cycle.  Nothing really exciting this time: we basically added a few
  new drivers and subdrivers and stabilized them in linux-next.  Some
  cleanups too.  With sunrisepoint Intel has a real fine fully featured
  pin control driver for contemporary hardware, and the AMD driver is
  also for large deployments.  Most of the others are ARM devices.

  New drivers:
    - Intel Sunrisepoint
    - AMD KERNCZ GPIO
    - Broadcom Cygnus IOMUX

  New subdrivers:
    - Marvell MVEBU Armada 39x SoCs
    - Samsung Exynos 5433
    - nVidia Tegra 210
    - Mediatek MT8135
    - Mediatek MT8173
    - AMLogic Meson8b
    - Qualcomm PM8916

  On top of this cleanups and development history for the above drivers
  as issues were fixed after merging"

* tag 'pinctrl-v4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (71 commits)
  pinctrl: sirf: move sgpio lock into state container
  pinctrl: Add support for PM8916 GPIO's and MPP's
  pinctrl: bcm2835: Fix support for threaded level triggered IRQs
  sh-pfc: r8a7790: add EtherAVB pin groups
  pinctrl: Document "function" + "pins" pinmux binding
  pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support
  pinctrl: fsl: imx: Check for 0 config register
  pinctrl: Add support for Meson8b
  documentation: Extend pinctrl docs for Meson8b
  pinctrl: Cleanup Meson8 driver
  Fix inconsistent spinlock of AMD GPIO driver which can be recognized by static analysis tool smatch. Declare constant Variables with Sparse's suggestion.
  pinctrl: at91: convert __raw to endian agnostic IO
  pinctrl: constify of_device_id array
  pinctrl: pinconf-generic: add dt node names to error messages
  pinctrl: pinconf-generic: scan also referenced phandle node
  pinctrl: mvebu: add suspend/resume support to Armada XP pinctrl driver
  pinctrl: st: Display pin's function when printing pinctrl debug information
  pinctrl: st: Show correct pin direction also in GPIO mode
  pinctrl: st: Supply a GPIO get_direction() call-back
  pinctrl: st: Move st_get_pio_control() further up the source file
  ...

Pull backlight updates from Lee Jones:
 "Changes to existing drivers:

   - Use of_get_child_by_name() instead of refcount; 88pm860x_bl

   - Terminate array with NULL element; da9052_bl"

* tag 'backlight-for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
  backlight: da9052_bl: Terminate da9052_wled_ids array with empty element
  backlight: 88pm860x_bl: Use of_get_child_by_name() instead of refcount hack

Pull MFD updates from Lee Jones:
 "Changes to existing drivers:

   - Rename child driver [axp288_battery => axp288_fuel_gauge]; axp20x
   - Rename child driver [max77693-flash => max77693-led]; max77693
   - Error handling fixes; intel_soc_pmic
   - GPIO tweaking; intel_soc_pmic
   - Remove non-DT code; vexpress-sysreg, tc3589x
   - Remove unused/legacy code; ti_am335x_tscadc, rts5249, rtsx_gops, rtsx_pcr,
                                rtc-s5m, sec-core, max77693, menelaus,
                                wm5102-tables
   - Trivial fixups; rtsx_pci, da9150-core, sec-core, max7769, max77693,
                     mc13xxx-core, dln2, hi6421-pmic-core, rk808, twl4030-power,
                     lpc_ich, menelaus, twl6040
   - Update register/address values; rts5227, rts5249
   - DT and/or binding document fixups; arizona, da9150, mt6397, axp20x,
                                        qcom-rpm, qcom-spmi-pmic
   - Couple of trivial core Kconfig fixups
   - Remove use of seq_printf return value; ab8500-debugfs
   - Remove __exit markups; menelaus, tps65010
   - Fix platform-device name collisions; mfd-core

  New drivers/supported devices:

   - Add support for wm8280/wm8281 into arizona
   - Add support for COMe-cBL6 into kempld-core
   - Add support for rts524a and rts525a into rts5249
   - Add support for ipq8064 into qcom_rpm
   - Add support for extcon into axp20x
   - New MediaTek MT6397 PMIC driver
   - New Maxim MAX77843 PMIC dirver
   - New Intel Quark X1000 I2C-GPIO driver
   - New Skyworks SKY81452 driver"

* tag 'mfd-for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (76 commits)
  mfd: sec: Fix RTC alarm interrupt number on S2MPS11
  mfd: wm5102: Remove registers for output 3R from readable list
  mfd: tps65010: Remove incorrect __exit markups
  mfd: devicetree: bindings: Add Qualcomm RPM regulator subnodes
  mfd: axp20x: Add support for extcon cell
  mfd: lpc_ich: Sort IDs
  mfd: twl6040: Remove wrong and unneeded "platform:twl6040" modalias
  mfd: qcom-spmi-pmic: Add specific compatible strings for Qualcomm's SPMI PMIC's
  mfd: axp20x: Fix duplicate const for model names
  mfd: menelaus: Use macro for magic number
  mfd: menelaus: Drop support for SW controller VCORE
  mfd: menelaus: Delete omap_has_menelaus
  mfd: arizona: Correct type of gpio_defaults
  mfd: lpc_ich: Sort IDs
  mfd: Fix a typo in Kconfig
  mfd: qcom_rpm: Add support for IPQ8064
  mfd: devicetree: qcom_rpm: Document IPQ8064 resources
  mfd: core: Fix platform-device name collisions
  mfd: intel_quark_i2c_gpio: Don't crash if !DMI
  dt-bindings: Add vendor-prefix for X-Powers
  ...

When task->comm is passed directly to audit_log_untrustedstring() without
getting a copy or using the task_lock, there is a race that could happen that
would output a NULL (\0) in the middle of the output string that would
effectively truncate the rest of the report text after the comm= field in the
audit log message, losing fields.

Using get_task_comm() to get a copy while acquiring the task_lock to prevent
this and to prevent the result from being a mixture of old and new values of
comm would incur potentially unacceptable overhead, considering that the value
can be influenced by userspace and therefore untrusted anyways.

Copy the value before passing it to audit_log_untrustedstring() ensures that a
local copy is used to calculate the length *and* subsequently printed.  Even if
this value contains a mix of old and new values, it will only calculate and
copy up to the first NULL, preventing the rest of the audit log message being
truncated.

Use a second local copy of comm to avoid a race between the first and second
calls to audit_log_untrustedstring() with comm.
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>

Merge first patchbomb from Andrew Morton:

 - arch/sh updates

 - ocfs2 updates

 - kernel/watchdog feature

 - about half of mm/

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (122 commits)
  Documentation: update arch list in the 'memtest' entry
  Kconfig: memtest: update number of test patterns up to 17
  arm: add support for memtest
  arm64: add support for memtest
  memtest: use phys_addr_t for physical addresses
  mm: move memtest under mm
  mm, hugetlb: abort __get_user_pages if current has been oom killed
  mm, mempool: do not allow atomic resizing
  memcg: print cgroup information when system panics due to panic_on_oom
  mm: numa: remove migrate_ratelimited
  mm: fold arch_randomize_brk into ARCH_HAS_ELF_RANDOMIZE
  mm: split ET_DYN ASLR from mmap ASLR
  s390: redefine randomize_et_dyn for ELF_ET_DYN_BASE
  mm: expose arch_mmap_rnd when available
  s390: standardize mmap_rnd() usage
  powerpc: standardize mmap_rnd() usage
  mips: extract logic for mmap_rnd()
  arm64: standardize mmap_rnd() usage
  x86: standardize mmap_rnd() usage
  arm: factor out mmap ASLR into mmap_rnd
  ...

Since arm64/arm support memtest command line option update the "memtest"
entry.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Additional test patterns for memtest were introduced since commit
63823126 ("x86: memtest: add additional (regular) test patterns"),
but looks like Kconfig was not updated that time.

Update Kconfig entry with the actual number of maximum test patterns.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add support for memtest command line option.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add support for memtest command line option.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Since memtest might be used by other architectures pass input parameters
as phys_addr_t instead of long to prevent overflow.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Memtest is a simple feature which fills the memory with a given set of
patterns and validates memory contents, if bad memory regions is detected
it reserves them via memblock API.  Since memblock API is widely used by
other architectures this feature can be enabled outside of x86 world.

This patch set promotes memtest to live under generic mm umbrella and
enables memtest feature for arm/arm64.

It was reported that this patch set was useful for tracking down an issue
with some errant DMA on an arm64 platform.

This patch (of 6):

There is nothing platform dependent in the core memtest code, so other
platforms might benefit from this feature too.

[linux@roeck-us.net: MEMTEST depends on MEMBLOCK]
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If __get_user_pages() is faulting a significant number of hugetlb pages,
usually as the result of mmap(MAP_LOCKED), it can potentially allocate a
very large amount of memory.

If the process has been oom killed, this will cause a lot of memory to
potentially deplete memory reserves.

In the same way that commit 4779280d ("mm: make get_user_pages()
interruptible") aborted for pending SIGKILLs when faulting non-hugetlb
memory, based on the premise of commit 462e00cc ("oom: stop
allocating user memory if TIF_MEMDIE is set"), hugetlb page faults now
terminate when the process has been oom killed.
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Greg Thelen <gthelen@google.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Davidlohr Bueso <dave@stgolabs.net>
Acked-by: "Kirill A. Shutemov" <kirill@shutemov.name>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Allocating a large number of elements in atomic context could quickly
deplete memory reserves, so just disallow atomic resizing entirely.

Nothing currently uses mempool_resize() with anything other than
GFP_KERNEL, so convert existing callers to drop the gfp_mask.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Steffen Maier <maier@linux.vnet.ibm.com>	[zfcp]
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Steve French <sfrench@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If kernel panics due to oom, caused by a cgroup reaching its limit, when
'compulsory panic_on_oom' is enabled, then we will only see that the OOM
happened because of "compulsory panic_on_oom is enabled" but this doesn't
tell the difference between mempolicy and memcg.  And dumping system wide
information is plain wrong and more confusing.  This patch provides the
information of the cgroup whose limit triggerred panic
Signed-off-by: Balasubramani Vivekanandan <balasubramani_vivekanandan@mentor.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This code is dead since commit 9e645ab6 ("sched/numa: Continue PTE
scanning even if migrate rate limited") so remove it.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>