This patch is to reduce the performance drop depth observed on SATA HDD
when ATA PT command is outstanding.

Driver returns IO commands with status "SAM_STAT_BUSY" whenever ATA PT
command is outstanding. With this, IO commands will be retried until this
outstanding ATA PT to complete and hence we will observe drop in
performance.

As the driver is completing the subsequent IOs commands with SAM_STAT_BUSY
status, these IOs has to go though the block layer.  Hence it adds latency
to the IOs and large performance drop is observed.

So to reduce this performance dropp, added improvement in driver to return
the subsequent IOs with SCSI_MLQUEUE_DEVICE_BUSY status instead of
completing the IOs with SAM_STAT_BUSY status when ATA PT command is
outstanding. Sending command back with SCSI_MLQUEUE_DEVICE_BUSY does not go
through complete block layer stack (as scsi_done won't be called) SML will
immediately retry the command and this method will avoid latency of block
layer stack and the performance impact will be reduced.

On Local setup, ran 512k sequential read IO operation on HGST SATA drive
with existing driver & with this improvement drivers and here is the
result,

1. With existing driver: IOs are running at bandwidth of ~230 rMB/s and
whenever any ATA PT command is outstanding (e.g issued from systemd-udevd
daemon) then this bandwidth drops to ~150 rMB/s.

2. With this improvement driver: IOs are running at bandwidth of ~230 rMB/s
and whenever any ATA PT command is outstanding then this bandwidth drops to
just ~190 rMB/s.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

During HBA initialization time, if handshake operation fails due to some
firmware fault then currently driver is terminating the HBA
initialization. It is possible that HBA may come up properly if diag reset
is issued.

So improvement is made in driver in such a way that before terminating the
HBA initialization, driver checks the IOC state and if IOC state is in
fault state then issue diag reset for once. If diag reset is successful
then continue with HBA initialization else terminate the HBA
initialization.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Currently with sysfs parameter "drv_support_bitmap" driver exposes whether
driver supports toolbox memory move command or not.

And application should issue the toolbox memory move command only if driver
tell that memory move tool box command is supported through this sysfs
parameter.

In future we can utilize this sysfs parameter if any new feature is added
and need to notify the same to applications.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Host uses the Memory Move Tool to copy data from any source/destination
combination of system memory and IOC memory.

Memory Move Tool box request contains two SGE fields, First SGE field must
contains the source buffer details described by an MPI Simple SGE.  The
second SGE field must contains the destination buffer details described by
an MPI Simple SGE.

 Source   ->   Destination

1. IOC    ->   IOC    (Both the SGE's will be filled by application)

2. HOST   ->   HOST   (Both the SGE's will be filled by the host,
               application should give sgl_offset to first SGE offset)

3. IOC    ->   HOST   (Application will fill the first SGE and set the
               sgl_offset to second SGE and hence driver fills
               the second SGE)
4. HOST   ->   IOC    (Application will fill IOC buffer information in the
               first SGE and set the sgl_offset to second SGE.
               Then driver will fill the second SGE with Host buffer
               information and just before posting the command to the
               firmware, driver will swap these two SGEs so that first
               SGE contains the HOST buffer information and second SGE
               contains the IOC information.

Driver has to take care only of the 4th case, other three cases are by
default supported by the current driver design.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

If driver sees the NVMe drive with "DEVICE_BLOCKED" AccessStatus in its
PCIe Device Page0, then driver removes the drive from its internal list and
does not allow any IOCTL commands to be sent to the drive and will return
the IOCTLs with "-ENODEV" status.

The driver will now allow NVMe Encapsulated IOCTL issued to the NVMe device
with an access status of DEVICE_BLOCKED. This change allows the user to
flash new drive firmware online and revive the drive.

Add NVMe device only the driver's internal list even though the device is
in the blocked state so that the device will be visible to Apps. This way
Apps can send NVMe Encapsulated IOCTLs to this drive and bring the drive
online. This NVMe drive with DEVICE_BLOCKED access status won't added to
the SML, it will be added only in the driver's internal list.

[mkp: clarified desc]
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

SES device of managed PCIe switch will be enumerated same as NVMe drives.

The device info type for this SES device is

        MPI26_PCIE_DEVINFO_SCSI (0x4),

whereas the device info type for NVMe drives is

        MPI26_PCIE_DEVINFO_NVME (0x3).

Based on this device info type driver determines whether the device is NVMe
drive or a SES device of a managed PCIe switch.

This SES device doesn't have the PCIe device page 2 information like NVMe
drives, so driver won't read PCIe device page 2 information for SES device.

This SES device uses only IEEE SGL's, So driver build's IEEE SGL's whenever
it receives any SCSI commands for this SES device.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Updated MPI to 2.6.8 specification and header files to 2.00.54.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Issue:

During online Firmware upgrade operations it is possible that MaxDevHandles
filled in IOCFacts may change with new FW.  With this we may observe kernel
panics when driver try to access the pd_handles or blocking_handles buffers
at offset greater than the old firmware's MaxDevHandle value.

Fix:

_base_check_ioc_facts_changes() looks for increase/decrease in IOCFacts
attributes during online firmware upgrade and increases the pd_handles,
blocking_handles, etc buffer sizes to new firmware's MaxDevHandle value if
this new firmware's MaxDevHandle value is greater than the old firmware's
MaxDevHandle value.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Driver gets a request frame from the free pool of DMA-able request frames
and fill in the required information and pass the address of the frame to
IOC/FW to pull the complete request frame. In certain places the driver
used the request frame allocated from the free pool without completely
clearing the previous data stored in it. The request contents were cleared
only for the size of the new request to be issued and that left out some
stale data in the unused part of the request. Though the IOC/FW is not
expected to access the request beyond the specified size, it is good
practice to clear complete request message frame.

So reinitialize the complete request message frame with 0s before using
it.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

PCIe Lane margin tool box request requires IEEE sgl's and hence driver
fills the SGL field with IEEE sgl's while issuing the PCIe Lane margin
ioctl request to the HBA firmware.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

There are several occasions where variable rc is being initialized with a
value that is never read and error is being re-assigned a little later on.
Clean up the code by removing rc entirely and just returning the return
value from the call to pm8001_issue_ssp_tmf

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

In hisi_sas_lu_reset(), we call internal abort for SAS and SATA device
codepaths -> consolidate into a single call.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The format specifier "%p" can leak kernel address, and use "%pK" instead.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Remove some unnecessary code, including:

 - Explicit zeroing of memory allocated for dmam_alloc_coherent()

 - Some duplicated code

 - Some redundant masking
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

For functions which always return 0, which is never checked, make to return
void.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

It will free irq automatically if devm_request_irq() failed, so drop
free_irq() if devm_request_irq() failed.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The SMP frame response is written to the command table and not the SMP
response pointer from libsas, so don't bother DMA mapping (and unmapping)
the SMP response from libsas.
Suggested-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The call to kmap_atomic() in the SMP command completion code is
unnecessary, since kmap() is only really concerned with highmem, which is
not relevant on arm64. The controller only finds itself in arm64 systems.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

For a system with PAGE_SIZE of 16K or 64K, the size every time we want to
alloc may be small like 4K, but for function dmam_alloc_coherent(), the
least size it allocates is PAGE_SIZE, so it will waste much memory for the
situation.

To solve the issue, limit the minimum allocation size of slot buf to
PAGE_SIZE.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

For struct hisi_sas_status_buffer, it contains struct hisi_sas_err_record
and iu[1024]. The struct iu[1024] will be filled fully by the response of
disks, so it is not need to initialize them to 0, but for the struct
hisi_sas_err_record, SAS controller only fill some fields of
hisi_sas_err_record according to hw designer, so it should be initialised
to 0.  After the change, cpu utilization percentage of memset() is changed
from 1.7% to 0.12%.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Fix a possible out-of-bounds access in hisi_sas_debug_I_T_nexus_reset().
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The AXI and RAS register values should also should be snapshot at debugfs.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The value of IOST/ITCT is updated to cache first, and then synchronize to
DDR periodically. So the value in IOST/ITCT cache is the latest data and
it's important for debugging.

So, the HW cache of IOST and ITCT should be snapshot at debugfs.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Fix how the pointer is set in hisi_sas_debugfs_iost_show() and
hisi_sas_debugfs_itct_show().
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

In commit 1273d65f ("scsi: hisi_sas: change queue depth from 512 to
4096"), the depth of each queue is the same as the max IPTT in the system.

As such, as long as we have an IPTT allocated, we will have enough space on
any delivery queue.

All .get_free_slot functions were checking for space on the queue by
reading the DQ read pointer. Drop this, and also raise the code into common
code, as there is nothing hw specific remaining.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

There is a small optimisation to be had by making the max IPTT the same for
all hw revisions, that being we can drop the check for read and write
pointer being the same in the get free slot function.

Change v1 hw to have max IPTT of 4096 - same as v2 and v3 hw - and
drop hisi_sas_hw.max_command_entries.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

If the userspace process crashes while we send the nl msg, it is possible
that the cmd in curr_nl_cmd of tcmu_dev never gets reset to 0, and and
returns busy for other commands after the userspace process is restartd.

More details below:

/backstores/user:file/file> set attribute dev_size=2048
Cannot set attribute dev_size: [Errno 3] No such process
/backstores/user:file/file> set attribute dev_size=2048
Cannot set attribute dev_size: [Errno 16] Device or resource busy

with following kernel messages:
[173605.747169] Unable to reconfigure device
[173616.686674] tcmu daemon: command reply support 1.
[173623.866978] netlink cmd 3 already executing on file
[173623.866984] Unable to reconfigure device

Also, it is not safe to leave the nl_cmd in the list, and not get deleted.

This patch removes the nl_cmd from the list, and clear its data if it is
not sent successfully.
Signed-off-by: Li Zhong <lizhongfs@gmail.com>
Acked-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Configure CDNS_UFS_REG_HCLKDIV in .hce_enable_notify() instead of
.setup_clock() because if UFSHCD resets the controller ip because of phy or
device related errors then CDNS_UFS_REG_HCLKDIV is reset to default value
and .setup_clock() is not called later in the sequence whereas
.hce_enable_notify will be called everytime controller is reenabled.
Signed-off-by: Anil Varughese <aniljoy@cadence.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The data structure used for log messages is so large that it can cause a
boot failure. Since allocations from that data structure can fail anyway,
use kmalloc() / kfree() instead of that data structure.

See also https://bugzilla.kernel.org/show_bug.cgi?id=204119.
See also commit ded85c19 ("scsi: Implement per-cpu logging buffer") # v4.0.
Reported-by: Jan Palus <jpalus@fastmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Jan Palus <jpalus@fastmail.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

If scsi_target_block() fails that can break the code that calls this
function. Hence complain loudly if scsi_target_block() fails.

Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The only 'new_state' values passed by upstream kernel code to
scsi_internal_device_unblock_nowait() are SDEV_RUNNING and
SDEV_TRANSPORT_OFFLINE. These are the only values that should be passed to
this function. Hence check the value of the 'new_state' argument to avoid
that scsi_internal_device_unblock_nowait() would be used to trigger an
illegal SCSI device state transition. In this context 'illegal' means not
allowed by scsi_device_set_state().

Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Define new a type: uc_string_id for easier string handling and less
casting. Reduce number or string copies in price of a dynamic allocation.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Mark switch cases where we are expecting to fall through.

This patch fixes the following warning (Building: m68k):

drivers/scsi/wd33c93.c: In function  round_4 :
drivers/scsi/wd33c93.c:1856:11: warning: this statement may fall through [-Wimplicit-fallthrough=]
   case 2: ++x;
           ^~~
drivers/scsi/wd33c93.c:1857:3: note: here
   case 3: ++x;
   ^~~~
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Mark switch cases where we are expecting to fall through.

This patch fixes the following warnings:

drivers/scsi/sun3_scsi.c: warning: this statement may fall through
[-Wimplicit-fallthrough=]:  => 399:9, 403:9
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Mark switch cases where we are expecting to fall through.

This patch fixes the following warnings (Building: sparc defconfig):

drivers/scsi/qlogicpti.c: In function 'qlogicpti_mbox_command':
drivers/scsi/qlogicpti.c:202:10: warning: this statement may fall through [-Wimplicit-fallthrough=]
  case 6: sbus_writew(param[5], qpti->qregs + MBOX5);
          ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/qlogicpti.c:203:2: note: here
  case 5: sbus_writew(param[4], qpti->qregs + MBOX4);
  ^~~~
drivers/scsi/qlogicpti.c:203:10: warning: this statement may fall through [-Wimplicit-fallthrough=]
  case 5: sbus_writew(param[4], qpti->qregs + MBOX4);
          ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/qlogicpti.c:204:2: note: here
  case 4: sbus_writew(param[3], qpti->qregs + MBOX3);
  ^~~~
drivers/scsi/qlogicpti.c:204:10: warning: this statement may fall through [-Wimplicit-fallthrough=]
  case 4: sbus_writew(param[3], qpti->qregs + MBOX3);
          ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/qlogicpti.c:205:2: note: here
  case 3: sbus_writew(param[2], qpti->qregs + MBOX2);
  ^~~~
drivers/scsi/qlogicpti.c:205:10: warning: this statement may fall through [-Wimplicit-fallthrough=]
  case 3: sbus_writew(param[2], qpti->qregs + MBOX2);
          ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/qlogicpti.c:206:2: note: here
  case 2: sbus_writew(param[1], qpti->qregs + MBOX1);
  ^~~~
drivers/scsi/qlogicpti.c:206:10: warning: this statement may fall through [-Wimplicit-fallthrough=]
  case 2: sbus_writew(param[1], qpti->qregs + MBOX1);
          ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/qlogicpti.c:207:2: note: here
  case 1: sbus_writew(param[0], qpti->qregs + MBOX0);
  ^~~~
drivers/scsi/qlogicpti.c:256:19: warning: this statement may fall through [-Wimplicit-fallthrough=]
  case 6: param[5] = sbus_readw(qpti->qregs + MBOX5);
          ~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/qlogicpti.c:257:2: note: here
  case 5: param[4] = sbus_readw(qpti->qregs + MBOX4);
  ^~~~
drivers/scsi/qlogicpti.c:257:19: warning: this statement may fall through [-Wimplicit-fallthrough=]
  case 5: param[4] = sbus_readw(qpti->qregs + MBOX4);
          ~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/qlogicpti.c:258:2: note: here
  case 4: param[3] = sbus_readw(qpti->qregs + MBOX3);
  ^~~~
drivers/scsi/qlogicpti.c:258:19: warning: this statement may fall through [-Wimplicit-fallthrough=]
  case 4: param[3] = sbus_readw(qpti->qregs + MBOX3);
          ~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/qlogicpti.c:259:2: note: here
  case 3: param[2] = sbus_readw(qpti->qregs + MBOX2);
  ^~~~
drivers/scsi/qlogicpti.c:259:19: warning: this statement may fall through [-Wimplicit-fallthrough=]
  case 3: param[2] = sbus_readw(qpti->qregs + MBOX2);
          ~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/qlogicpti.c:260:2: note: here
  case 2: param[1] = sbus_readw(qpti->qregs + MBOX1);
  ^~~~
drivers/scsi/qlogicpti.c:260:19: warning: this statement may fall through [-Wimplicit-fallthrough=]
  case 2: param[1] = sbus_readw(qpti->qregs + MBOX1);
          ~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/qlogicpti.c:261:2: note: here
  case 1: param[0] = sbus_readw(qpti->qregs + MBOX0);
  ^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Mark switch cases where we are expecting to fall through.

This patch fixes the following warnings:

drivers/scsi/ibmvscsi/ibmvfc.c: In function 'ibmvfc_npiv_login_done':
drivers/scsi/ibmvscsi/ibmvfc.c:4022:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
   ibmvfc_retry_host_init(vhost);
   ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/ibmvscsi/ibmvfc.c:4023:2: note: here
  case IBMVFC_MAD_DRIVER_FAILED:
  ^~~~
drivers/scsi/ibmvscsi/ibmvfc.c: In function 'ibmvfc_bsg_request':
drivers/scsi/ibmvscsi/ibmvfc.c:1830:11: warning: this statement may fall through [-Wimplicit-fallthrough=]
   port_id = (bsg_request->rqst_data.h_els.port_id[0] << 16) |
   ~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    (bsg_request->rqst_data.h_els.port_id[1] << 8) |
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    bsg_request->rqst_data.h_els.port_id[2];
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/ibmvscsi/ibmvfc.c:1833:2: note: here
  case FC_BSG_RPT_ELS:
  ^~~~
drivers/scsi/ibmvscsi/ibmvfc.c:1838:11: warning: this statement may fall through [-Wimplicit-fallthrough=]
   port_id = (bsg_request->rqst_data.h_ct.port_id[0] << 16) |
   ~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    (bsg_request->rqst_data.h_ct.port_id[1] << 8) |
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    bsg_request->rqst_data.h_ct.port_id[2];
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/ibmvscsi/ibmvfc.c:1841:2: note: here
  case FC_BSG_RPT_CT:
  ^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The commit de516379 ("scsi: megaraid_sas: changes to function
prototypes") introduced a comilation warning due to it changed the function
prototype of read_fw_status_reg() to take an instance pointer instead, but
forgot to remove an unused variable.

drivers/scsi/megaraid/megaraid_sas_fusion.c: In function
'megasas_fusion_update_can_queue':
drivers/scsi/megaraid/megaraid_sas_fusion.c:326:39: warning: variable
'reg_set' set but not used [-Wunused-but-set-variable]
  struct megasas_register_set __iomem *reg_set;
                                       ^~~~~~~
Fixes: de516379 ("scsi: megaraid_sas: changes to function prototypes")
Signed-off-by: Qian Cai <cai@lca.pw>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Fix sparse warnings:

drivers/scsi/megaraid/megaraid_sas_fusion.c:3369:1: warning: symbol 'complete_cmd_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:3535:6: warning: symbol 'megasas_sync_irqs' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:3554:1: warning: symbol 'megasas_complete_cmd_dpc_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:3573:13: warning: symbol 'megasas_isr_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:3604:1: warning: symbol 'build_mpt_mfi_pass_thru' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:3661:40: warning: symbol 'build_mpt_cmd' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:3688:1: warning: symbol 'megasas_issue_dcmd_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:3881:5: warning: symbol 'megasas_wait_for_outstanding_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:4005:6: warning: symbol 'megasas_refire_mgmt_cmd' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:4525:25: warning: symbol 'megasas_get_peer_instance' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:4825:7: warning: symbol 'megasas_fusion_crash_dump' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>