Starting with MC10.14.0, dpaa2_io_service_enqueue_fq() API is
functional. Since there are a number of cases where it offers
better performance compared to the currently used enqueue
function, switch to it for firmware versions that support it.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While in NAPI context, free skbs by calling napi_consume_skb()
instead of dev_kfree_skb(), to take advantage of the bulk freeing
mechanism.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of allocating page fragments via the network stack,
use the page allocator directly. For now, we consume one page
for each Rx buffer.

With the new memory model we are free to consider adding more
XDP support.

Performance decreases slightly in some IP forwarding cases.
No visible effect on termination traffic. The driver memory
footprint increases as a result of this change, but it is
still small enough to not really matter.

Another side effect is that now Rx buffer alignment requirements
are naturally satisfied without any additional actions needed.
Remove alignment related code, except in the buffer layout
information conveyed to MC, as hardware still needs to know the
alignment value we guarantee.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
add flow_rule infrastructure

This patchset, as is, allows us to reuse the driver codebase to
configure ACL hardware offloads for the ethtool_rxnfc and the TC flower
interfaces. A few clients for this infrastructure are presented, such as
the bcm_sf2 and the qede drivers, for reference. Moreover all of the
existing drivers in the tree are converted to use this infrastructure.

This patchset is re-using the existing flow dissector infrastructure
that was introduced by Jiri Pirko et al. so the amount of abstractions
that this patchset adds are minimal. Well, just a few wrapper structures
for the selector side of the rules. And, in order to express actions,
this patchset exposes an action API that is based on the existing TC
action infrastructure and what existing drivers already support on that
front.

v7: This patchset is a rebase on top of the net-next tree, after
    addressing questions and feedback from driver developers in the
    last batch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The qede driver supports for ethtool_rx_flow_spec and flower, both
codebases look very similar.

This patch uses the ethtool_rx_flow_rule() infrastructure to remove the
duplicated ethtool_rx_flow_spec parser and consolidate ACL offload
support around the flow_rule infrastructure.

Furthermore, more code can be consolidated by merging
qede_add_cls_rule() and qede_add_tc_flower_fltr(), these two functions
also look very similar.

This driver currently provides simple ACL support, such as 5-tuple
matching, drop policy and queue to CPU.

Drivers that support more features can benefit from this infrastructure
to save even more redundant codebase.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a preparation patch to reuse the existing TC flower codebase
from ethtool_rx_flow_spec.

This patch is merely moving the core ethtool_rx_flow_spec parser after
tc flower offload driver code so we can skip a few forward function
declarations in the follow up patch.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update this driver to use the flow_rule infrastructure, hence we can use
the same code to populate hardware IR from ethtool_rx_flow and the
cls_flower interfaces.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a function to translate the ethtool_rx_flow_spec
structure to the flow_rule representation.

This allows us to reuse code from the driver side given that both flower
and ethtool_rx_flow interfaces use the same representation.

This patch also includes support for the flow type flags FLOW_EXT,
FLOW_MAC_EXT and FLOW_RSS.

The ethtool_rx_flow_spec_input wrapper structure is used to convey the
rss_context field, that is away from the ethtool_rx_flow_spec structure,
and the ethtool_rx_flow_spec structure.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These actions need to be added to support the ethtool_rx_flow interface.
The queue action includes a field to specify the RSS context, that is
set via FLOW_RSS flow type flag and the rss_context field in struct
ethtool_rxnfc, plus the corresponding queue index. FLOW_RSS implies that
rss_context is non-zero, therefore, queue.ctx == 0 means that FLOW_RSS
was not set. Also add a field to store the vf index which is stored in
the ethtool_rxnfc ring_cookie field.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that drivers have been converted to use the flow action
infrastructure, remove this field from the tc_cls_flower_offload
structure.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch updates drivers to use the new flow action infrastructure.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch provides the flow_stats structure that acts as container for
tc_cls_flower_offload, then we can use to restore the statistics on the
existing TC actions. Hence, tcf_exts_stats_update() is not used from
drivers anymore.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch implements a new function to translate from native TC action
to the new flow_action representation. Moreover, this patch also updates
cls_flower to use this new function.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This new infrastructure defines the nic actions that you can perform
from existing network drivers. This infrastructure allows us to avoid a
direct dependency with the native software TC action representation.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds pedit_headers_action structure to store the result of
parsing tc pedit actions. Then, it calls alloc_tc_pedit_action() to
populate the mlx5e hardware intermediate representation once all actions
have been parsed.

This patch comes in preparation for the new flow_action infrastructure,
where each packet mangling comes in an separated action, ie. not packed
as in tc pedit.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch wraps the dissector key and mask - that flower uses to
represent the matching side - around the flow_match structure.

To avoid a follow up patch that would edit the same LoCs in the drivers,
this patch also wraps this new flow match structure around the flow rule
object. This new structure will also contain the flow actions in follow
up patches.

This introduces two new interfaces:

	bool flow_rule_match_key(rule, dissector_id)

that returns true if a given matching key is set on, and:

	flow_rule_match_XYZ(rule, &match);

To fetch the matching side XYZ into the match container structure, to
retrieve the key and the mask with one single call.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
net: phy: add and use further MMD accessors

Add MMD accessors for modifying MMD registers and clearing / setting
bits in MMD registers. Use these accessors in PHY drivers and phylib.

v2:
- fix SoB in patch 2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Make use of the new MMD accessors.

v2:
- fix SoB
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds full set of locked and unlocked accessor functions to read and
write PHY MMD registers and/or bitfields.

Set of functions exactly matches what is already available for PHY
legacy registers.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-for-davem-2019-02-06' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for 5.1

First set of patches for 5.1. Lots of new features in various drivers
but nothing really special standing out.

Major changes:

brcmfmac

* DMI nvram filename quirk for PoV TAB-P1006W-232 tablet

rsi

* support for hardware scan offload

iwlwifi

* support for Target Wakeup Time (TWT) -- a feature that allows the AP
  to specify when individual stations can access the medium

* support for mac80211 AMSDU handling

* some new PCI IDs

* relicense the pcie submodule to dual GPL/BSD

* reworked the TOF/CSI (channel estimation matrix) implementation

* Some product name updates in the human-readable strings

mt76

* energy detect regulatory compliance fixes

* preparation for MT7603 support

* channel switch announcement support

mwifiex

* support for sd8977 chipset

qtnfmac

* support for 4addr mode

* convert to SPDX license identifiers
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2019-02-05

This series contains updates to igc, e1000e, ixgbe, fm10k and driver
documentation.

Kai-Heng Feng fixes an e1000e issue where the Wake-On-LAN settings where
being set incorrectly during a system suspend.

Sasha addresses community feedback on the igc driver and provides a
number of code cleanups to remove either unreachable or unused code.  In
addition, added basic ethtool support for the igc driver.

Mike Rapoport fixes the formatting of the kernel driver documentation so
that the title is properly formatted and does not get lumped with the
document sections in the HTML kernel documents generated.

Jiri Kosina updates a hard coded RAR entries value with the existing
define IXGBE_82599_RAR_ENTRIES.

Jake fixes up whitespace in the fm10k driver.

Konstantin Khlebnikov fixes an issue where in some cases, the e1000e
driver will continually reset during a system boot because the watchdog
task sees items in the transmit buffer but the carrier is off (trying to
establish link) causing the device reset to flush the buffer.  To
resolve, just move this check/flush into the watchdog section for when
the carrier is off.

Todd bumps the igb driver version to reflect the recent driver changes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds basic ethtool support to the device to allow
for configuration.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

With recent changes, need to bump the driver version to reflect the
changes.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove the redundant 'igc_get_phy_id_base' method and use
the 'igc_get_phy_id' method directly instead.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove the redundant 'igc_read_mac_addr_base' method and use
the 'igc_read_mac_addr' method directly instead.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

I'm seeing series of e1000e resets (sometimes endless) at system boot
if something generates tx traffic at this time. In my case this is
netconsole who sends message "e1000e 0000:02:00.0: Some CPU C-states
have been disabled in order to enable jumbo frames" from e1000e itself.
As result e1000_watchdog_task sees used tx buffer while carrier is off
and start this reset cycle again.

[   17.794359] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[   17.794714] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   22.936455] e1000e 0000:02:00.0 eth1: changing MTU from 1500 to 9000
[   23.033336] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   26.102364] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[   27.174495] 8021q: 802.1Q VLAN Support v1.8
[   27.174513] 8021q: adding VLAN 0 to HW filter on device eth1
[   30.671724] cgroup: cgroup: disabling cgroup2 socket matching due to net_prio or net_cls activation
[   30.898564] netpoll: netconsole: local port 6666
[   30.898566] netpoll: netconsole: local IPv6 address 2a02:6b8:0:80b:beae:c5ff:fe28:23f8
[   30.898567] netpoll: netconsole: interface 'eth1'
[   30.898568] netpoll: netconsole: remote port 6666
[   30.898568] netpoll: netconsole: remote IPv6 address 2a02:6b8:b000:605c:e61d:2dff:fe03:3790
[   30.898569] netpoll: netconsole: remote ethernet address b0:a8:6e:f4:ff:c0
[   30.917747] console [netcon0] enabled
[   30.917749] netconsole: network logging started
[   31.453353] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   34.185730] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   34.321840] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   34.465822] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   34.597423] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   34.745417] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   34.877356] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   35.005441] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   35.157376] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   35.289362] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   35.417441] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   37.790342] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None

This patch flushes tx buffers only once when carrier is off
rather than at each watchdog iteration.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove the 'igc_get_link_up_info_base method' from igc_base.c file.
Use the 'igc_get_speed_and_duplex_copper' method directly and reduce
the code redundancy.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove unused igc_adv_data_desc definition from igc_base.h file.
Descriptors definition will be added per demand.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The change is based on the issue found by Kangjie Lu <kjlu@umn.edu> where
we not checking the return value of a register read/write which could result
in a NULL pointer dereference if the read/write fails.

Since we are only trying to disable the far-end loopback, if the read
and write of register fails, we do not want to bail out of the function.
We just want to log that it failed to disable and continue on.

CC: Sasha Neftin <sasha.neftin@intel.com>
CC: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The function comment for fm10k_iov_msg_msix_pf has an extra space in
a sentence, which is unnecessary.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe_reset_hw_82599() resets the value of hw->mac.num_rar_entries to
pre-defined value of 128. Let's get rid of that hardcoded literal, and use
IXGBE_82599_RAR_ENTRIES instead, the same way the normal initialization
path does.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove redundant igc_check_for_link_base code and replace it with
an igc_check_for_copper_link method.
Fix duplication of IGC_ADVTXD_PAYLEN_SHIFT mask declaration.
Remove obsolete IGC_SCVPC register definition.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The documentation of Intel drivers is missing the heading adornment for
document titles.

This causes the generated html to have TOC entries from these documents to
appear as top level TOC entries:

* Linux* Base Driver for Intel(R) Ethernet Network Connection
* Contents
* Identifying Your Adapter
* Command Line Parameters
  * AutoNeg
  * Duplex
  ...

Add overline heading adornment to document titles.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Address community comment.
Remove the unreachable code leads to the static checker warning.
PHY functionality will be added later per demand.
Reported by Dan Carpenter.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e sets different WoL settings in system suspend callback and
runtime suspend callback.

The suspend direct complete optimization leaves e1000e in runtime
suspended state with wrong WoL setting during system suspend.

To fix this, we need to disable suspend direct complete optimization to
let e1000e always use suspend callback to set correct WoL during system
suspend.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Sven Auhagen reports that if he changes a SFP+ module for a SFP module
on the Macchiatobin Single Shot, the link does not come back up.  For
Sven, it is as easy as:

- Insert a SFP+ module connected, and use ping6 to verify link is up.
- Remove SFP+ module
- Insert SFP 1000base-X module use ping6 to verify link is up: Link
  up event did not trigger and the link is down

but that doesn't show the problem for me.  Locally, this has been
reproduced by:

- Boot with no modules.
- Insert SFP+ module, confirm link is up.
- Replace module with 25000base-X module.  Confirm link is up.
- Set remote end down, link is reported as dropped at both ends.
- Set remote end up, link is reported up at remote end, but not local
  end due to lack of link interrupt.

Fix this by setting up both GMAC and XLG interrupts for port 0, but
only unmasking the appropriate interrupt according to the current mode
set in the mac_config() method.  However, only do the mask/unmask
dance when we are really changing the link mode to avoid missing any
link interrupts.
Tested-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the phy_interface_mode_is_8023z() helper for detecting interface
modes that use 802.3z serial encoding.  This is equivalent to testing
for both 1000base-X and 2500base-X.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Moritz Fischer says:

====================
nixge: Fixed-link support

This series adds fixed-link support to nixge.

The first patch corrects the binding to correctly reflect
hardware that does not come with MDIO cores instantiated.

The second patch adds fixed link support to the driver.

The third patch updates the binding document with the now
optional (formerly required) phy-handle property and references
the fixed-link docs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Update device-tree binding with fixed-link support.

With fixed-link support the formerly required property 'phy-handle'
is now optional if 'fixed-link' child is present.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for fixed-link configurations to nixge driver.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>