- 30 Oct, 2019 11 commits
-
-
Markus Theil authored
Mesh path nexthop should be a ethernet address, but current validation checks against 4 byte integers. Cc: stable@vger.kernel.org Fixes: 2ec600d6 ("nl80211/cfg80211: support for mesh, sta dumping") Signed-off-by:
Markus Theil <markus.theil@tu-ilmenau.de> Link: https://lore.kernel.org/r/20191029093003.10355-1-markus.theil@tu-ilmenau.deSigned-off-by:
Johannes Berg <johannes.berg@intel.com>
-
Masashi Honma authored
This patch disables setting of HT20 and more for channel 14 because the channel is only for IEEE 802.11b. The patch for net/wireless/util.c was unit-tested. The patch for net/wireless/chan.c was tested with iw command. Before this patch. $ sudo iw dev <ifname> set channel 14 HT20 $ After this patch. $ sudo iw dev <ifname> set channel 14 HT20 kernel reports: invalid channel definition command failed: Invalid argument (-22) $ Signed-off-by:
Masashi Honma <masashi.honma@gmail.com> Link: https://lore.kernel.org/r/20191021075045.2719-1-masashi.honma@gmail.com [clean up the code, use != instead of equivalent >] Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linuxDavid S. Miller authored
Saeed Mahameed says: ==================== Mellanox, mlx5 fixes 2019-10-24 This series introduces misc fixes to mlx5 driver. v1->v2: - Dropped the kTLS counter documentation patch, Tariq will fix it and send it later. - Added a new fix for link speed mode reporting. ('net/mlx5e: Initialize link modes bitmap on stack') For -stable v4.14 ('net/mlx5e: Fix handling of compressed CQEs in case of low NAPI budget') For -stable v4.19 ('net/mlx5e: Fix ethtool self test: link speed') For -stable v5.2 ('net/mlx5: Fix flow counter list auto bits struct') ('net/mlx5: Fix rtable reference leak') For -stable v5.3 ('net/mlx5e: Remove incorrect match criteria assignment line') ('net/mlx5e: Determine source port properly for vlan push action') ('net/mlx5e: Initialize link modes bitmap on stack') ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Nikolay Aleksandrov authored
A simple typo fix in the nl error message (fbd -> fdb). CC: David Ahern <dsahern@gmail.com> Fixes: 8c6e137f ("rtnetlink: Update rtnl_fdb_dump for strict data checking") Signed-off-by:
Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
-
Ursula Braun authored
If a nonblocking socket is immediately closed after connect(), the connect worker may not have started. This results in a refcount problem, since sock_hold() is called from the connect worker. This patch moves the sock_hold in front of the connect worker scheduling. Reported-by: syzbot+4c063e6dea39e4b79f29@syzkaller.appspotmail.com Fixes: 50717a37 ("net/smc: nonblocking connect rework") Reviewed-by:
Karsten Graul <kgraul@linux.ibm.com> Signed-off-by:
Ursula Braun <ubraun@linux.ibm.com> Signed-off-by:
-
Taehee Yoo authored
When a bonding interface is being created, it setups its mode and options. At that moment, it uses mode_lock so mode_lock should be initialized before that moment. rtnl_newlink() rtnl_create_link() alloc_netdev_mqs() ->setup() //bond_setup() ->newlink //bond_newlink bond_changelink() register_netdevice() ->ndo_init() //bond_init() After commit 089bca2c ("bonding: use dynamic lockdep key instead of subclass"), mode_lock is initialized in bond_init(). So in the bond_changelink(), un-initialized mode_lock can be used. mode_lock should be initialized in bond_setup(). This patch partially reverts commit 089bca2c ("bonding: use dynamic lockdep key instead of subclass") Test command: ip link add bond0 type bond mode 802.3ad lacp_rate 0 Splat looks like: [ 60.615127] INFO: trying to register non-static key. [ 60.615900] the code is fine but needs lockdep annotation. [ 60.616697] turning off the locking correctness validator. [ 60.617490] CPU: 1 PID: 957 Comm: ip Not tainted 5.4.0-rc3+ #109 [ 60.618350] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 [ 60.619481] Call Trace: [ 60.619918] dump_stack+0x7c/0xbb [ 60.620453] register_lock_class+0x1215/0x14d0 [ 60.621131] ? alloc_netdev_mqs+0x7b3/0xcc0 [ 60.621771] ? is_bpf_text_address+0x86/0xf0 [ 60.622416] ? is_dynamic_key+0x230/0x230 [ 60.623032] ? unwind_get_return_address+0x5f/0xa0 [ 60.623757] ? create_prof_cpu_mask+0x20/0x20 [ 60.624408] ? arch_stack_walk+0x83/0xb0 [ 60.625023] __lock_acquire+0xd8/0x3de0 [ 60.625616] ? stack_trace_save+0x82/0xb0 [ 60.626225] ? stack_trace_consume_entry+0x160/0x160 [ 60.626957] ? deactivate_slab.isra.80+0x2c5/0x800 [ 60.627668] ? register_lock_class+0x14d0/0x14d0 [ 60.628380] ? alloc_netdev_mqs+0x7b3/0xcc0 [ 60.629020] ? save_stack+0x69/0x80 [ 60.629574] ? save_stack+0x19/0x80 [ 60.630121] ? __kasan_kmalloc.constprop.4+0xa0/0xd0 [ 60.630859] ? __kmalloc_node+0x16f/0x480 [ 60.631472] ? alloc_netdev_mqs+0x7b3/0xcc0 [ 60.632121] ? rtnl_create_link+0x2ed/0xad0 [ 60.634388] ? __rtnl_newlink+0xad4/0x11b0 [ 60.635024] lock_acquire+0x164/0x3b0 [ 60.635608] ? bond_3ad_update_lacp_rate+0x91/0x200 [bonding] [ 60.636463] _raw_spin_lock_bh+0x38/0x70 [ 60.637084] ? bond_3ad_update_lacp_rate+0x91/0x200 [bonding] [ 60.637930] bond_3ad_update_lacp_rate+0x91/0x200 [bonding] [ 60.638753] ? bond_3ad_lacpdu_recv+0xb30/0xb30 [bonding] [ 60.639552] ? bond_opt_get_val+0x180/0x180 [bonding] [ 60.640307] ? ___slab_alloc+0x5aa/0x610 [ 60.640925] bond_option_lacp_rate_set+0x71/0x140 [bonding] [ 60.641751] __bond_opt_set+0x1ff/0xbb0 [bonding] [ 60.643217] ? kasan_unpoison_shadow+0x30/0x40 [ 60.643924] bond_changelink+0x9a4/0x1700 [bonding] [ 60.644653] ? memset+0x1f/0x40 [ 60.742941] ? bond_slave_changelink+0x1a0/0x1a0 [bonding] [ 60.752694] ? alloc_netdev_mqs+0x8ea/0xcc0 [ 60.753330] ? rtnl_create_link+0x2ed/0xad0 [ 60.753964] bond_newlink+0x1e/0x60 [bonding] [ 60.754612] __rtnl_newlink+0xb9f/0x11b0 [ ... ] Reported-by: syzbot+8da67f407bcba2c72e6e@syzkaller.appspotmail.com Reported-by: syzbot+0d083911ab18b710da71@syzkaller.appspotmail.com Fixes: 089bca2c ("bonding: use dynamic lockdep key instead of subclass") Signed-off-by:
Taehee Yoo <ap420073@gmail.com> Signed-off-by:
-
Anson Huang authored
Use platform_get_irq_byname_optional() and platform_get_irq_optional() instead of platform_get_irq_byname() and platform_get_irq() for optional IRQs to avoid below error message during probe: [ 0.795803] fec 30be0000.ethernet: IRQ pps not found [ 0.800787] fec 30be0000.ethernet: IRQ index 3 not found Signed-off-by:
Anson Huang <Anson.Huang@nxp.com> Acked-by:
Fugang Duan <fugang.duan@nxp.com> Reviewed-by:
Stephen Boyd <swboyd@chromium.org> Signed-off-by:
-
Anson Huang authored
Failed to get irq using name is NOT fatal as driver will use index to get irq instead, use platform_get_irq_byname_optional() instead of platform_get_irq_byname() to avoid below error message during probe: [ 0.819312] fec 30be0000.ethernet: IRQ int0 not found [ 0.824433] fec 30be0000.ethernet: IRQ int1 not found [ 0.829539] fec 30be0000.ethernet: IRQ int2 not found Signed-off-by:
-
Jakub Kicinski authored
Dave's Facebook email address is not working, and my attempts to contact him are failing. Let's remove it to trim down the list of TLS maintainers. Signed-off-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by:
Simon Horman <simon.horman@netronome.com> Signed-off-by:
-
Xin Long authored
This patch is to improve the tun_info options_len by dropping the skb when TUNNEL_VXLAN_OPT is set but options_len is less than vxlan_metadata. This can void a potential out-of-bounds access on ip_tun_info. Fixes: ee122c79 ("vxlan: Flow based tunneling") Signed-off-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
-
Xin Long authored
The check for !md doens't really work for ip_tunnel_info_opts(info) which only does info + 1. Also to avoid out-of-bounds access on info, it should ensure options_len is not less than erspan_metadata in both erspan_xmit() and ip6erspan_tunnel_xmit(). Fixes: 1a66a836 ("gre: add collect_md mode to ERSPAN tunnel") Signed-off-by:
-
- 29 Oct, 2019 19 commits
-
-
Jiangfeng Xiao authored
This is due to error in over budget processing. When dealing with high throughput, the used buffers that exceeds the budget is not cleaned up. In addition, it takes a lot of cycles to clean up the used buffer, and then the buffer where the valid data is located can take effect. Signed-off-by:
Jiangfeng Xiao <xiaojiangfeng@huawei.com> Signed-off-by:
-
Eran Ben Elisha authored
Prior to this patch, the amount of counters guaranteed per VF in the resource tracker was MLX4_VF_COUNTERS_PER_PORT * MLX4_MAX_PORTS. It was set regardless if the VF was single or dual port. This caused several VFs to have no guaranteed counters although the system could satisfy their request. The fix is to dynamically guarantee counters, based on each VF specification. Fixes: 9de92c60 ("net/mlx4_core: Adjust counter grant policy in the resource tracker") Signed-off-by:
Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by:
Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
-
Aya Levin authored
Initialize link modes bitmap on stack before using it, otherwise the outcome of ethtool set link ksettings might have unexpected values. Fixes: 4b95840a ("net/mlx5e: Fix matching of speed to PRM link modes") Signed-off-by:
Aya Levin <ayal@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com>
-
Aya Levin authored
Ethtool self test contains a test for link speed. This test reads the PTYS register and determines whether the current speed is valid or not. Change current implementation to use the function mlx5e_port_linkspeed() that does the same check and fails when speed is invalid. This code redundancy lead to a bug when mlx5e_port_linkspeed() was updated with expended speeds and the self test was not. Fixes: 2c81bfd5 ("net/mlx5e: Move port speed code from en_ethtool.c to en/port.c") Signed-off-by:
Moshe Shemesh <moshe@mellanox.com> Signed-off-by:
-
Maxim Mikityanskiy authored
When CQE compression is enabled, compressed CQEs use the following structure: a title is followed by one or many blocks, each containing 8 mini CQEs (except the last, which may contain fewer mini CQEs). Due to NAPI budget restriction, a complete structure is not always parsed in one NAPI run, and some blocks with mini CQEs may be deferred to the next NAPI poll call - we have the mlx5e_decompress_cqes_cont call in the beginning of mlx5e_poll_rx_cq. However, if the budget is extremely low, some blocks may be left even after that, but the code that follows the mlx5e_decompress_cqes_cont call doesn't check it and assumes that a new CQE begins, which may not be the case. In such cases, random memory corruptions occur. An extremely low NAPI budget of 8 is used when busy_poll or busy_read is active. This commit adds a check to make sure that the previous compressed CQE has been completely parsed after mlx5e_decompress_cqes_cont, otherwise it prevents a new CQE from being fetched in the middle of a compressed CQE. This commit fixes random crashes in __build_skb, __page_pool_put_page and other not-related-directly places, that used to happen when both CQE compression and busy_poll/busy_read were enabled. Fixes: 7219ab34 ("net/mlx5e: CQE compression") Signed-off-by:
Maxim Mikityanskiy <maximmi@mellanox.com> Signed-off-by:
-
Vlad Buslov authored
Geneve implementation changed mlx5 tc to user direct pointer to tunnel_key action's internal struct ip_tunnel_info instance. However, this leads to use-after-free error when initial filter that caused creation of new encap entry is deleted or when tunnel_key action is manually overwritten through action API. Moreover, with recent TC offloads API unlocking change struct flow_action_entry->tunnel point to temporal copy of tunnel info that is deallocated after filter is offloaded to hardware which causes bug to reproduce every time new filter is attached to existing encap entry with following KASAN bug: [ 314.885555] ================================================================== [ 314.886641] BUG: KASAN: use-after-free in memcmp+0x2c/0x60 [ 314.886864] Read of size 1 at addr ffff88886c746280 by task tc/2682 [ 314.887179] CPU: 22 PID: 2682 Comm: tc Not tainted 5.3.0-rc7+ #703 [ 314.887188] Hardware name: Supermicro SYS-2028TP-DECR/X10DRT-P, BIOS 2.0b 03/30/2017 [ 314.887195] Call Trace: [ 314.887215] dump_stack+0x9a/0xf0 [ 314.887236] print_address_description+0x67/0x323 [ 314.887248] ? memcmp+0x2c/0x60 [ 314.887257] ? memcmp+0x2c/0x60 [ 314.887272] __kasan_report.cold+0x1a/0x3d [ 314.887474] ? __mlx5e_tc_del_fdb_peer_flow+0x100/0x1b0 [mlx5_core] [ 314.887484] ? memcmp+0x2c/0x60 [ 314.887509] kasan_report+0xe/0x12 [ 314.887521] memcmp+0x2c/0x60 [ 314.887662] mlx5e_tc_add_fdb_flow+0x51b/0xbe0 [mlx5_core] [ 314.887838] ? mlx5e_encap_take+0x110/0x110 [mlx5_core] [ 314.887902] ? lockdep_init_map+0x87/0x2c0 [ 314.887924] ? __init_waitqueue_head+0x4f/0x60 [ 314.888062] ? mlx5e_alloc_flow.isra.0+0x18c/0x1c0 [mlx5_core] [ 314.888207] __mlx5e_add_fdb_flow+0x2d7/0x440 [mlx5_core] [ 314.888359] ? mlx5e_tc_update_neigh_used_value+0x6f0/0x6f0 [mlx5_core] [ 314.888374] ? match_held_lock+0x2e/0x240 [ 314.888537] mlx5e_configure_flower+0x830/0x16a0 [mlx5_core] [ 314.888702] ? __mlx5e_add_fdb_flow+0x440/0x440 [mlx5_core] [ 314.888713] ? down_read+0x118/0x2c0 [ 314.888728] ? down_read_killable+0x300/0x300 [ 314.888882] ? mlx5e_rep_get_ethtool_stats+0x180/0x180 [mlx5_core] [ 314.888899] tc_setup_cb_add+0x127/0x270 [ 314.888937] fl_hw_replace_filter+0x2ac/0x380 [cls_flower] [ 314.888976] ? fl_hw_destroy_filter+0x1b0/0x1b0 [cls_flower] [ 314.888990] ? fl_change+0xbcf/0x27ef [cls_flower] [ 314.889030] ? fl_change+0xa57/0x27ef [cls_flower] [ 314.889069] fl_change+0x16bd/0x27ef [cls_flower] [ 314.889135] ? __rhashtable_insert_fast.constprop.0+0xa00/0xa00 [cls_flower] [ 314.889167] ? __radix_tree_lookup+0xa4/0x130 [ 314.889200] ? fl_get+0x169/0x240 [cls_flower] [ 314.889218] ? fl_walk+0x230/0x230 [cls_flower] [ 314.889249] tc_new_tfilter+0x5e1/0xd40 [ 314.889281] ? __rhashtable_insert_fast.constprop.0+0xa00/0xa00 [cls_flower] [ 314.889309] ? tc_del_tfilter+0xa30/0xa30 [ 314.889335] ? __lock_acquire+0x5b5/0x2460 [ 314.889378] ? find_held_lock+0x85/0xa0 [ 314.889442] ? tc_del_tfilter+0xa30/0xa30 [ 314.889465] rtnetlink_rcv_msg+0x4ab/0x5f0 [ 314.889488] ? rtnl_dellink+0x490/0x490 [ 314.889518] ? lockdep_hardirqs_on+0x260/0x260 [ 314.889538] ? netlink_deliver_tap+0xab/0x5a0 [ 314.889550] ? match_held_lock+0x1b/0x240 [ 314.889575] netlink_rcv_skb+0xd0/0x200 [ 314.889588] ? rtnl_dellink+0x490/0x490 [ 314.889605] ? netlink_ack+0x440/0x440 [ 314.889635] ? netlink_deliver_tap+0x161/0x5a0 [ 314.889648] ? lock_downgrade+0x360/0x360 [ 314.889657] ? lock_acquire+0xe5/0x210 [ 314.889686] netlink_unicast+0x296/0x350 [ 314.889707] ? netlink_attachskb+0x390/0x390 [ 314.889726] ? _copy_from_iter_full+0xe0/0x3a0 [ 314.889738] ? __virt_addr_valid+0xbb/0x130 [ 314.889771] netlink_sendmsg+0x394/0x600 [ 314.889800] ? netlink_unicast+0x350/0x350 [ 314.889817] ? move_addr_to_kernel.part.0+0x90/0x90 [ 314.889852] ? netlink_unicast+0x350/0x350 [ 314.889872] sock_sendmsg+0x96/0xa0 [ 314.889891] ___sys_sendmsg+0x482/0x520 [ 314.889919] ? copy_msghdr_from_user+0x250/0x250 [ 314.889930] ? __fput+0x1fa/0x390 [ 314.889941] ? task_work_run+0xb7/0xf0 [ 314.889957] ? exit_to_usermode_loop+0x117/0x120 [ 314.889972] ? entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 314.889982] ? do_syscall_64+0x74/0xe0 [ 314.889992] ? entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 314.890012] ? mark_lock+0xac/0x9a0 [ 314.890028] ? __lock_acquire+0x5b5/0x2460 [ 314.890053] ? mark_lock+0xac/0x9a0 [ 314.890083] ? __lock_acquire+0x5b5/0x2460 [ 314.890112] ? match_held_lock+0x1b/0x240 [ 314.890144] ? __fget_light+0xa1/0xf0 [ 314.890166] ? sockfd_lookup_light+0x91/0xb0 [ 314.890187] __sys_sendmsg+0xba/0x130 [ 314.890201] ? __sys_sendmsg_sock+0xb0/0xb0 [ 314.890225] ? __blkcg_punt_bio_submit+0xd0/0xd0 [ 314.890264] ? lockdep_hardirqs_off+0xbe/0x100 [ 314.890274] ? mark_held_locks+0x24/0x90 [ 314.890286] ? do_syscall_64+0x1e/0xe0 [ 314.890308] do_syscall_64+0x74/0xe0 [ 314.890325] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 314.890336] RIP: 0033:0x7f00ca33d7b8 [ 314.890348] Code: 89 02 48 c7 c0 ff ff ff ff eb bb 0f 1f 80 00 00 00 00 f3 0f 1e fa 48 8d 05 65 8f 0c 00 8b 00 85 c0 75 17 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 58 c3 0f 1f 80 00 00 00 00 48 83 ec 28 89 5 4 [ 314.890356] RSP: 002b:00007ffea2983928 EFLAGS: 00000246 ORIG_RAX: 000000000000002e [ 314.890369] RAX: ffffffffffffffda RBX: 000000005d777d5b RCX: 00007f00ca33d7b8 [ 314.890377] RDX: 0000000000000000 RSI: 00007ffea2983990 RDI: 0000000000000003 [ 314.890384] RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000006 [ 314.890392] R10: 0000000000404eda R11: 0000000000000246 R12: 0000000000000001 [ 314.890400] R13: 000000000047f640 R14: 00007ffea2987b58 R15: 0000000000000021 [ 314.890529] Allocated by task 2687: [ 314.890684] save_stack+0x1b/0x80 [ 314.890694] __kasan_kmalloc.constprop.0+0xc2/0xd0 [ 314.890705] __kmalloc_track_caller+0x102/0x340 [ 314.890721] kmemdup+0x1d/0x40 [ 314.890730] tc_setup_flow_action+0x731/0x2c27 [ 314.890743] fl_hw_replace_filter+0x23b/0x380 [cls_flower] [ 314.890756] fl_change+0x16bd/0x27ef [cls_flower] [ 314.890765] tc_new_tfilter+0x5e1/0xd40 [ 314.890776] rtnetlink_rcv_msg+0x4ab/0x5f0 [ 314.890786] netlink_rcv_skb+0xd0/0x200 [ 314.890796] netlink_unicast+0x296/0x350 [ 314.890805] netlink_sendmsg+0x394/0x600 [ 314.890815] sock_sendmsg+0x96/0xa0 [ 314.890825] ___sys_sendmsg+0x482/0x520 [ 314.890834] __sys_sendmsg+0xba/0x130 [ 314.890844] do_syscall_64+0x74/0xe0 [ 314.890854] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 314.890937] Freed by task 2687: [ 314.891076] save_stack+0x1b/0x80 [ 314.891086] __kasan_slab_free+0x12c/0x170 [ 314.891095] kfree+0xeb/0x2f0 [ 314.891106] tc_cleanup_flow_action+0x69/0xa0 [ 314.891119] fl_hw_replace_filter+0x2c5/0x380 [cls_flower] [ 314.891132] fl_change+0x16bd/0x27ef [cls_flower] [ 314.891140] tc_new_tfilter+0x5e1/0xd40 [ 314.891151] rtnetlink_rcv_msg+0x4ab/0x5f0 [ 314.891161] netlink_rcv_skb+0xd0/0x200 [ 314.891170] netlink_unicast+0x296/0x350 [ 314.891180] netlink_sendmsg+0x394/0x600 [ 314.891190] sock_sendmsg+0x96/0xa0 [ 314.891200] ___sys_sendmsg+0x482/0x520 [ 314.891208] __sys_sendmsg+0xba/0x130 [ 314.891218] do_syscall_64+0x74/0xe0 [ 314.891228] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 314.891315] The buggy address belongs to the object at ffff88886c746280 which belongs to the cache kmalloc-96 of size 96 [ 314.891762] The buggy address is located 0 bytes inside of 96-byte region [ffff88886c746280, ffff88886c7462e0) [ 314.892196] The buggy address belongs to the page: [ 314.892387] page:ffffea0021b1d180 refcount:1 mapcount:0 mapping:ffff88835d00ef80 index:0x0 [ 314.892398] flags: 0x57ffffc0000200(slab) [ 314.892413] raw: 0057ffffc0000200 ffffea00219e0340 0000000800000008 ffff88835d00ef80 [ 314.892423] raw: 0000000000000000 0000000080200020 00000001ffffffff 0000000000000000 [ 314.892430] page dumped because: kasan: bad access detected [ 314.892515] Memory state around the buggy address: [ 314.892707] ffff88886c746180: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc [ 314.892976] ffff88886c746200: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc [ 314.893251] >ffff88886c746280: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc [ 314.893522] ^ [ 314.893657] ffff88886c746300: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc [ 314.893924] ffff88886c746380: 00 00 00 00 00 00 00 00 00 fc fc fc fc fc fc fc [ 314.894189] ================================================================== Fix the issue by duplicating tunnel info into per-encap copy that is deallocated with encap structure. Also, duplicate tunnel info in flow parse attribute to support cases when flow might be attached asynchronously. Fixes: 1f6da306 ("net/mlx5e: Geneve, Keep tunnel info as pointer to the original struct") Signed-off-by:Vlad Buslov <vladbu@mellanox.com> Reviewed-by:
Yevgeny Kliteynik <kliteyn@mellanox.com> Reviewed-by:
Roi Dayan <roid@mellanox.com> Signed-off-by:
-
Eli Britstein authored
The cited commit refactored the encap id into a struct pointed from the destination. Bug fix for the case there is no encap for one of the destinations. Fixes: 2b688ea5 ("net/mlx5: Add flow steering actions to fs_cmd shim layer") Signed-off-by:
Eli Britstein <elibr@mellanox.com> Reviewed-by:
-
Parav Pandit authored
If the rt entry gateway family is not AF_INET for multipath device, rtable reference is leaked. Hence, fix it by releasing the reference. Fixes: 5fb091e8 ("net/mlx5e: Use hint to resolve route when in HW multipath mode") Fixes: e32ee6c7 ("net/mlx5e: Support tunnel encap over tagged Ethernet") Signed-off-by:
Parav Pandit <parav@mellanox.com> Signed-off-by:
-
Vlad Buslov authored
When encap entry initialization completes successfully e->compl_result is set to positive value and not zero, like mlx5e_rep_update_flows() assumes at the moment. Fix the conditional to only skip encap flows update when e->compl_result < 0. Fixes: 2a1f1768 ("net/mlx5e: Refactor neigh update for concurrent execution") Signed-off-by:
-
Maor Gottlieb authored
Memory allocated by kvzalloc should be freed by kvfree. Fixes: cef35af3 ("net/mlx5e: Add mlx5e HV VHCA stats agent") Signed-off-by:
Maor Gottlieb <maorg@mellanox.com> Signed-off-by:
-
Dmytro Linkin authored
Driver have function, which enable match criteria for misc parameters in dependence of eswitch capabilities. Fixes: 4f5d1bea ("Merge branch 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux") Signed-off-by:
Dmytro Linkin <dmitrolin@mellanox.com> Reviewed-by:
Jianbo Liu <jianbol@mellanox.com> Reviewed-by:
-
Dmytro Linkin authored
Termination tables are used for vlan push actions on uplink ports. To support RoCE dual port the source port value was placed in a register. Fix the code to use an API method returning the source port according to the FW capabilities. Fixes: 10caabda ("net/mlx5e: Use termination table for VLAN push actions") Signed-off-by:
Oz Shlomo <ozsh@mellanox.com> Reviewed-by:
-
Roi Dayan authored
The union should contain the extended dest and counter list. Remove the resevered 0x40 bits which is redundant. This change doesn't break any functionally. Everything works today because the code in fs_cmd.c is using the correct structs if extended dest or the basic dest. Fixes: 1b115498 ("net/mlx5: Introduce extended destination fields") Signed-off-by:
Mark Bloch <markb@mellanox.com> Signed-off-by:
-
David S. Miller authored
Vladimir Oltean says: ==================== VLAN fixes for Ocelot switch This series addresses 2 issues with vlan_filtering=1: - Untagged traffic gets dropped unless commands are run in a very specific order. - Untagged traffic starts being transmitted as tagged after adding another untagged VID on the port. Tested on NXP LS1028A-RDB board. ==================== Signed-off-by: -
Vladimir Oltean authored
The switch driver keeps a "vid" variable per port, which signifies _the_ VLAN ID that is stripped on that port's egress (aka the native VLAN on a trunk port). That is the way the hardware is designed (mostly). The port->vid is programmed into REW:PORT:PORT_VLAN_CFG:PORT_VID and the rewriter is told to send all traffic as tagged except the one having port->vid. There exists a possibility of finer-grained egress untagging decisions: using the VCAP IS1 engine, one rule can be added to match every VLAN-tagged frame whose VLAN should be untagged, and set POP_CNT=1 as action. However, the IS1 can hold at most 512 entries, and the VLANs are in the order of 6 * 4096. So the code is fine for now. But this sequence of commands: $ bridge vlan add dev swp0 vid 1 pvid untagged $ bridge vlan add dev swp0 vid 2 untagged makes untagged and pvid-tagged traffic be sent out of swp0 as tagged with VID 1, despite user's request. Prevent that from happening. The user should temporarily remove the existing untagged VLAN (1 in this case), add it back as tagged, and then add the new untagged VLAN (2 in this case). Cc: Antoine Tenart <antoine.tenart@bootlin.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Fixes: 7142529f ("net: mscc: ocelot: add VLAN filtering") Signed-off-by:
Vladimir Oltean <olteanv@gmail.com> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Acked-by:
Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by:
-
Vladimir Oltean authored
Background information: the driver operates the hardware in a mode where a single VLAN can be transmitted as untagged on a particular egress port. That is the "native VLAN on trunk port" use case. Its value is held in port->vid. Consider the following command sequence (no network manager, all interfaces are down, debugging prints added by me): $ ip link add dev br0 type bridge vlan_filtering 1 $ ip link set dev swp0 master br0 Kernel code path during last command: br_add_slave -> ocelot_netdevice_port_event (NETDEV_CHANGEUPPER): [ 21.401901] ocelot_vlan_port_apply: port 0 vlan aware 0 pvid 0 vid 0 br_add_slave -> nbp_vlan_init -> switchdev_port_attr_set -> ocelot_port_attr_set (SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING): [ 21.413335] ocelot_vlan_port_apply: port 0 vlan aware 1 pvid 0 vid 0 br_add_slave -> nbp_vlan_init -> nbp_vlan_add -> br_switchdev_port_vlan_add -> switchdev_port_obj_add -> ocelot_port_obj_add -> ocelot_vlan_vid_add [ 21.667421] ocelot_vlan_port_apply: port 0 vlan aware 1 pvid 1 vid 1 So far so good. The bridge has replaced the driver's default pvid used in standalone mode (0) with its own default_pvid (1). The port's vid (native VLAN) has also changed from 0 to 1. $ ip link set dev swp0 up [ 31.722956] 8021q: adding VLAN 0 to HW filter on device swp0 do_setlink -> dev_change_flags -> vlan_vid_add -> ocelot_vlan_rx_add_vid -> ocelot_vlan_vid_add: [ 31.728700] ocelot_vlan_port_apply: port 0 vlan aware 1 pvid 1 vid 0 The 8021q module uses the .ndo_vlan_rx_add_vid API on .ndo_open to make ports be able to transmit and receive 802.1p-tagged traffic by default. This API is supposed to offload a VLAN sub-interface, which for a switch port means to add a VLAN that is not a pvid, and tagged on egress. But the driver implementation of .ndo_vlan_rx_add_vid is wrong: it adds back vid 0 as "egress untagged". Now back to the initial paragraph: there is a single untagged VID that the driver keeps track of, and that has just changed from 1 (the pvid) to 0. So this breaks the bridge core's expectation, because it has changed vid 1 from untagged to tagged, when what the user sees is. $ bridge vlan port vlan ids swp0 1 PVID Egress Untagged br0 1 PVID Egress Untagged But curiously, instead of manifesting itself as "untagged and pvid-tagged traffic gets sent as tagged on egress", the bug: - is hidden when vlan_filtering=0 - manifests as dropped traffic when vlan_filtering=1, due to this setting: if (port->vlan_aware && !port->vid) /* If port is vlan-aware and tagged, drop untagged and priority * tagged frames. */ val |= ANA_PORT_DROP_CFG_DROP_UNTAGGED_ENA | ANA_PORT_DROP_CFG_DROP_PRIO_S_TAGGED_ENA | ANA_PORT_DROP_CFG_DROP_PRIO_C_TAGGED_ENA; which would have made sense if it weren't for this bug. The setting's intention was "this is a trunk port with no native VLAN, so don't accept untagged traffic". So the driver was never expecting to set VLAN 0 as the value of the native VLAN, 0 was just encoding for "invalid". So the fix is to not send 802.1p traffic as untagged, because that would change the port's native vlan to 0, unbeknownst to the bridge, and trigger unexpected code paths in the driver. Cc: Antoine Tenart <antoine.tenart@bootlin.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Fixes: 7142529f ("net: mscc: ocelot: add VLAN filtering") Signed-off-by:
Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by:
-
Navid Emamdoost authored
In the implementation of i2400m_op_rfkill_sw_toggle() the allocated buffer for cmd should be released before returning. The documentation for i2400m_msg_to_dev() says when it returns the buffer can be reused. Meaning cmd should be released in either case. Move kfree(cmd) before return to be reached by all execution paths. Fixes: 2507e6ab ("wimax: i2400: fix memory leak") Signed-off-by:
Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by:
-
Jiangfeng Xiao authored
When rmmod hip04_eth.ko, we can get the following warning: Task track: rmmod(1623)>bash(1591)>login(1581)>init(1) ------------[ cut here ]------------ WARNING: CPU: 0 PID: 1623 at kernel/irq/manage.c:1557 __free_irq+0xa4/0x2ac() Trying to free already-free IRQ 200 Modules linked in: ping(O) pramdisk(O) cpuinfo(O) rtos_snapshot(O) interrupt_ctrl(O) mtdblock mtd_blkdevrtfs nfs_acl nfs lockd grace sunrpc xt_tcpudp ipt_REJECT iptable_filter ip_tables x_tables nf_reject_ipv CPU: 0 PID: 1623 Comm: rmmod Tainted: G O 4.4.193 #1 Hardware name: Hisilicon A15 [<c020b408>] (rtos_unwind_backtrace) from [<c0206624>] (show_stack+0x10/0x14) [<c0206624>] (show_stack) from [<c03f2be4>] (dump_stack+0xa0/0xd8) [<c03f2be4>] (dump_stack) from [<c021a780>] (warn_slowpath_common+0x84/0xb0) [<c021a780>] (warn_slowpath_common) from [<c021a7e8>] (warn_slowpath_fmt+0x3c/0x68) [<c021a7e8>] (warn_slowpath_fmt) from [<c026876c>] (__free_irq+0xa4/0x2ac) [<c026876c>] (__free_irq) from [<c0268a14>] (free_irq+0x60/0x7c) [<c0268a14>] (free_irq) from [<c0469e80>] (release_nodes+0x1c4/0x1ec) [<c0469e80>] (release_nodes) from [<c0466924>] (__device_release_driver+0xa8/0x104) [<c0466924>] (__device_release_driver) from [<c0466a80>] (driver_detach+0xd0/0xf8) [<c0466a80>] (driver_detach) from [<c0465e18>] (bus_remove_driver+0x64/0x8c) [<c0465e18>] (bus_remove_driver) from [<c02935b0>] (SyS_delete_module+0x198/0x1e0) [<c02935b0>] (SyS_delete_module) from [<c0202ed0>] (__sys_trace_return+0x0/0x10) ---[ end trace bb25d6123d849b44 ]--- Currently "rmmod hip04_eth.ko" call free_irq more than once as devres_release_all and hip04_remove both call free_irq. This results in a 'Trying to free already-free IRQ' warning. To solve the problem free_irq has been moved out of hip04_remove. Signed-off-by:
-
Will Deacon authored
In the highly unlikely event that we fail to allocate either of the "/txrx" or "/control" workqueues, we should bail cleanly rather than blindly march on with NULL queue pointer(s) installed in the 'fjes_adapter' instance. Cc: "David S. Miller" <davem@davemloft.net> Reported-by:
Nicolas Waisman <nico@semmle.com> Link: https://lore.kernel.org/lkml/CADJ_3a8WFrs5NouXNqS5WYe7rebFP+_A5CheeqAyD_p7DFJJcg@mail.gmail.com/Signed-off-by:
Will Deacon <will@kernel.org> Signed-off-by:
-
- 28 Oct, 2019 10 commits
-
-
git://git.open-mesh.org/linux-mergeDavid S. Miller authored
Simon Wunderlich says: ==================== Here are two batman-adv bugfixes: * Fix free/alloc race for OGM and OGMv2, by Sven Eckelmann (2 patches) ==================== Signed-off-by: -
Daniel Wagner authored
lan78xx_status() will run with interrupts enabled due to the change in ed194d13 ("usb: core: remove local_irq_save() around ->complete() handler"). generic_handle_irq() expects to be run with IRQs disabled. [ 4.886203] 000: irq 79 handler irq_default_primary_handler+0x0/0x8 enabled interrupts [ 4.886243] 000: WARNING: CPU: 0 PID: 0 at kernel/irq/handle.c:152 __handle_irq_event_percpu+0x154/0x168 [ 4.896294] 000: Modules linked in: [ 4.896301] 000: CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.3.6 #39 [ 4.896310] 000: Hardware name: Raspberry Pi 3 Model B+ (DT) [ 4.896315] 000: pstate: 60000005 (nZCv daif -PAN -UAO) [ 4.896321] 000: pc : __handle_irq_event_percpu+0x154/0x168 [ 4.896331] 000: lr : __handle_irq_event_percpu+0x154/0x168 [ 4.896339] 000: sp : ffff000010003cc0 [ 4.896346] 000: x29: ffff000010003cc0 x28: 0000000000000060 [ 4.896355] 000: x27: ffff000011021980 x26: ffff00001189c72b [ 4.896364] 000: x25: ffff000011702bc0 x24: ffff800036d6e400 [ 4.896373] 000: x23: 000000000000004f x22: ffff000010003d64 [ 4.896381] 000: x21: 0000000000000000 x20: 0000000000000002 [ 4.896390] 000: x19: ffff8000371c8480 x18: 0000000000000060 [ 4.896398] 000: x17: 0000000000000000 x16: 00000000000000eb [ 4.896406] 000: x15: ffff000011712d18 x14: 7265746e69206465 [ 4.896414] 000: x13: ffff000010003ba0 x12: ffff000011712df0 [ 4.896422] 000: x11: 0000000000000001 x10: ffff000011712e08 [ 4.896430] 000: x9 : 0000000000000001 x8 : 000000000003c920 [ 4.896437] 000: x7 : ffff0000118cc410 x6 : ffff0000118c7f00 [ 4.896445] 000: x5 : 000000000003c920 x4 : 0000000000004510 [ 4.896453] 000: x3 : ffff000011712dc8 x2 : 0000000000000000 [ 4.896461] 000: x1 : 73a3f67df94c1500 x0 : 0000000000000000 [ 4.896466] 000: Call trace: [ 4.896471] 000: __handle_irq_event_percpu+0x154/0x168 [ 4.896481] 000: handle_irq_event_percpu+0x50/0xb0 [ 4.896489] 000: handle_irq_event+0x40/0x98 [ 4.896497] 000: handle_simple_irq+0xa4/0xf0 [ 4.896505] 000: generic_handle_irq+0x24/0x38 [ 4.896513] 000: intr_complete+0xb0/0xe0 [ 4.896525] 000: __usb_hcd_giveback_urb+0x58/0xd8 [ 4.896533] 000: usb_giveback_urb_bh+0xd0/0x170 [ 4.896539] 000: tasklet_action_common.isra.0+0x9c/0x128 [ 4.896549] 000: tasklet_hi_action+0x24/0x30 [ 4.896556] 000: __do_softirq+0x120/0x23c [ 4.896564] 000: irq_exit+0xb8/0xd8 [ 4.896571] 000: __handle_domain_irq+0x64/0xb8 [ 4.896579] 000: bcm2836_arm_irqchip_handle_irq+0x60/0xc0 [ 4.896586] 000: el1_irq+0xb8/0x140 [ 4.896592] 000: arch_cpu_idle+0x10/0x18 [ 4.896601] 000: do_idle+0x200/0x280 [ 4.896608] 000: cpu_startup_entry+0x20/0x28 [ 4.896615] 000: rest_init+0xb4/0xc0 [ 4.896623] 000: arch_call_rest_init+0xc/0x14 [ 4.896632] 000: start_kernel+0x454/0x480 Fixes: ed194d13 ("usb: core: remove local_irq_save() around ->complete() handler") Cc: Woojung Huh <woojung.huh@microchip.com> Cc: Marc Zyngier <maz@kernel.org> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Stefan Wahren <wahrenst@gmx.net> Cc: Jisheng Zhang <Jisheng.Zhang@synaptics.com> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: David Miller <davem@davemloft.net> Signed-off-by:
Daniel Wagner <dwagner@suse.de> Tested-by:
Stefan Wahren <wahrenst@gmx.net> Signed-off-by:
-
Arnd Bergmann authored
An earlier bugfix introduced a dependency on CONFIG_NET_SCH_TAPRIO, but this missed the case of NET_SCH_TAPRIO=m and NET_DSA_SJA1105=y, which still causes a link error: drivers/net/dsa/sja1105/sja1105_tas.o: In function `sja1105_setup_tc_taprio': sja1105_tas.c:(.text+0x5c): undefined reference to `taprio_offload_free' sja1105_tas.c:(.text+0x3b4): undefined reference to `taprio_offload_get' drivers/net/dsa/sja1105/sja1105_tas.o: In function `sja1105_tas_teardown': sja1105_tas.c:(.text+0x6ec): undefined reference to `taprio_offload_free' Change the dependency to only allow selecting the TAS code when it can link against the taprio code. Fixes: a8d570de ("net: dsa: sja1105: Add dependency for NET_DSA_SJA1105_TAS") Fixes: 317ab5b8 ("net: dsa: sja1105: Configure the Time-Aware Scheduler via tc-taprio offload") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Benjamin Herrenschmidt authored
We are calling the checksum helper after the dma_map_single() call to map the packet. This is incorrect as the checksumming code will touch the packet from the CPU. This means the cache won't be properly flushes (or the bounce buffering will leave us with the unmodified packet to DMA). This moves the calculation of the checksum & vlan tags to before the DMA mapping. This also has the side effect of fixing another bug: If the checksum helper fails, we goto "drop" to drop the packet, which will not unmap the DMA mapping. Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Fixes: 05690d63 ("ftgmac100: Upgrade to NETIF_F_HW_CSUM") Reviewed-by:
Vijay Khemka <vijaykhemka@fb.com> Tested-by:
-
Tejun Heo authored
sk_page_frag() optimizes skb_frag allocations by using per-task skb_frag cache when it knows it's the only user. The condition is determined by seeing whether the socket allocation mask allows blocking - if the allocation may block, it obviously owns the task's context and ergo exclusively owns current->task_frag. Unfortunately, this misses recursion through memory reclaim path. Please take a look at the following backtrace. [2] RIP: 0010:tcp_sendmsg_locked+0xccf/0xe10 ... tcp_sendmsg+0x27/0x40 sock_sendmsg+0x30/0x40 sock_xmit.isra.24+0xa1/0x170 [nbd] nbd_send_cmd+0x1d2/0x690 [nbd] nbd_queue_rq+0x1b5/0x3b0 [nbd] __blk_mq_try_issue_directly+0x108/0x1b0 blk_mq_request_issue_directly+0xbd/0xe0 blk_mq_try_issue_list_directly+0x41/0xb0 blk_mq_sched_insert_requests+0xa2/0xe0 blk_mq_flush_plug_list+0x205/0x2a0 blk_flush_plug_list+0xc3/0xf0 [1] blk_finish_plug+0x21/0x2e _xfs_buf_ioapply+0x313/0x460 __xfs_buf_submit+0x67/0x220 xfs_buf_read_map+0x113/0x1a0 xfs_trans_read_buf_map+0xbf/0x330 xfs_btree_read_buf_block.constprop.42+0x95/0xd0 xfs_btree_lookup_get_block+0x95/0x170 xfs_btree_lookup+0xcc/0x470 xfs_bmap_del_extent_real+0x254/0x9a0 __xfs_bunmapi+0x45c/0xab0 xfs_bunmapi+0x15/0x30 xfs_itruncate_extents_flags+0xca/0x250 xfs_free_eofblocks+0x181/0x1e0 xfs_fs_destroy_inode+0xa8/0x1b0 destroy_inode+0x38/0x70 dispose_list+0x35/0x50 prune_icache_sb+0x52/0x70 super_cache_scan+0x120/0x1a0 do_shrink_slab+0x120/0x290 shrink_slab+0x216/0x2b0 shrink_node+0x1b6/0x4a0 do_try_to_free_pages+0xc6/0x370 try_to_free_mem_cgroup_pages+0xe3/0x1e0 try_charge+0x29e/0x790 mem_cgroup_charge_skmem+0x6a/0x100 __sk_mem_raise_allocated+0x18e/0x390 __sk_mem_schedule+0x2a/0x40 [0] tcp_sendmsg_locked+0x8eb/0xe10 tcp_sendmsg+0x27/0x40 sock_sendmsg+0x30/0x40 ___sys_sendmsg+0x26d/0x2b0 __sys_sendmsg+0x57/0xa0 do_syscall_64+0x42/0x100 entry_SYSCALL_64_after_hwframe+0x44/0xa9 In [0], tcp_send_msg_locked() was using current->page_frag when it called sk_wmem_schedule(). It already calculated how many bytes can be fit into current->page_frag. Due to memory pressure, sk_wmem_schedule() called into memory reclaim path which called into xfs and then IO issue path. Because the filesystem in question is backed by nbd, the control goes back into the tcp layer - back into tcp_sendmsg_locked(). nbd sets sk_allocation to (GFP_NOIO | __GFP_MEMALLOC) which makes sense - it's in the process of freeing memory and wants to be able to, e.g., drop clean pages to make forward progress. However, this confused sk_page_frag() called from [2]. Because it only tests whether the allocation allows blocking which it does, it now thinks current->page_frag can be used again although it already was being used in [0]. After [2] used current->page_frag, the offset would be increased by the used amount. When the control returns to [0], current->page_frag's offset is increased and the previously calculated number of bytes now may overrun the end of allocated memory leading to silent memory corruptions. Fix it by adding gfpflags_normal_context() which tests sleepable && !reclaim and use it to determine whether to use current->task_frag. v2: Eric didn't like gfp flags being tested twice. Introduce a new helper gfpflags_normal_context() and combine the two tests. Signed-off-by:Tejun Heo <tj@kernel.org> Cc: Josef Bacik <josef@toxicpanda.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Eric Dumazet authored
KCSAN reported a data-race in udp_set_dev_scratch() [1] The issue here is that we must not write over skb fields if skb is shared. A similar issue has been fixed in commit 89c22d8c ("net: Fix skb csum races when peeking") While we are at it, use a helper only dealing with udp_skb_scratch(skb)->csum_unnecessary, as this allows udp_set_dev_scratch() to be called once and thus inlined. [1] BUG: KCSAN: data-race in udp_set_dev_scratch / udpv6_recvmsg write to 0xffff888120278317 of 1 bytes by task 10411 on cpu 1: udp_set_dev_scratch+0xea/0x200 net/ipv4/udp.c:1308 __first_packet_length+0x147/0x420 net/ipv4/udp.c:1556 first_packet_length+0x68/0x2a0 net/ipv4/udp.c:1579 udp_poll+0xea/0x110 net/ipv4/udp.c:2720 sock_poll+0xed/0x250 net/socket.c:1256 vfs_poll include/linux/poll.h:90 [inline] do_select+0x7d0/0x1020 fs/select.c:534 core_sys_select+0x381/0x550 fs/select.c:677 do_pselect.constprop.0+0x11d/0x160 fs/select.c:759 __do_sys_pselect6 fs/select.c:784 [inline] __se_sys_pselect6 fs/select.c:769 [inline] __x64_sys_pselect6+0x12e/0x170 fs/select.c:769 do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x44/0xa9 read to 0xffff888120278317 of 1 bytes by task 10413 on cpu 0: udp_skb_csum_unnecessary include/net/udp.h:358 [inline] udpv6_recvmsg+0x43e/0xe90 net/ipv6/udp.c:310 inet6_recvmsg+0xbb/0x240 net/ipv6/af_inet6.c:592 sock_recvmsg_nosec+0x5c/0x70 net/socket.c:871 ___sys_recvmsg+0x1a0/0x3e0 net/socket.c:2480 do_recvmmsg+0x19a/0x5c0 net/socket.c:2601 __sys_recvmmsg+0x1ef/0x200 net/socket.c:2680 __do_sys_recvmmsg net/socket.c:2703 [inline] __se_sys_recvmmsg net/socket.c:2696 [inline] __x64_sys_recvmmsg+0x89/0xb0 net/socket.c:2696 do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Reported by Kernel Concurrency Sanitizer on: CPU: 0 PID: 10413 Comm: syz-executor.0 Not tainted 5.4.0-rc3+ #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Fixes: 2276f58a ("udp: use a separate rx queue for packet reception") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
syzbot <syzkaller@googlegroups.com> Cc: Paolo Abeni <pabeni@redhat.com> Reviewed-by:
Paolo Abeni <pabeni@redhat.com> Signed-off-by:
-
Nishad Kamdar authored
This patch corrects the SPDX License Identifier style in header files related to DPAA2 Ethernet driver supporting Freescale SoCs with DPAA2. For C header files Documentation/process/license-rules.rst mandates C-like comments (opposed to C source files where C++ style should be used) Changes made by using a script provided by Joe Perches here: https://lkml.org/lkml/2019/2/7/46. Suggested-by:
Joe Perches <joe@perches.com> Signed-off-by:
Nishad Kamdar <nishadkamdar@gmail.com> Signed-off-by:
-
David S. Miller authored
Eric Dumazet says: ==================== net: avoid KCSAN splats Often times we use skb_queue_empty() without holding a lock, meaning that other cpus (or interrupt) can change the queue under us. This is fine, but we need to properly annotate the lockless intent to make sure the compiler wont over optimize things. ==================== Signed-off-by: -
Eric Dumazet authored
__skb_wait_for_more_packets() can be called while other cpus can feed packets to the socket receive queue. KCSAN reported : BUG: KCSAN: data-race in __skb_wait_for_more_packets / __udp_enqueue_schedule_skb write to 0xffff888102e40b58 of 8 bytes by interrupt on cpu 0: __skb_insert include/linux/skbuff.h:1852 [inline] __skb_queue_before include/linux/skbuff.h:1958 [inline] __skb_queue_tail include/linux/skbuff.h:1991 [inline] __udp_enqueue_schedule_skb+0x2d7/0x410 net/ipv4/udp.c:1470 __udp_queue_rcv_skb net/ipv4/udp.c:1940 [inline] udp_queue_rcv_one_skb+0x7bd/0xc70 net/ipv4/udp.c:2057 udp_queue_rcv_skb+0xb5/0x400 net/ipv4/udp.c:2074 udp_unicast_rcv_skb.isra.0+0x7e/0x1c0 net/ipv4/udp.c:2233 __udp4_lib_rcv+0xa44/0x17c0 net/ipv4/udp.c:2300 udp_rcv+0x2b/0x40 net/ipv4/udp.c:2470 ip_protocol_deliver_rcu+0x4d/0x420 net/ipv4/ip_input.c:204 ip_local_deliver_finish+0x110/0x140 net/ipv4/ip_input.c:231 NF_HOOK include/linux/netfilter.h:305 [inline] NF_HOOK include/linux/netfilter.h:299 [inline] ip_local_deliver+0x133/0x210 net/ipv4/ip_input.c:252 dst_input include/net/dst.h:442 [inline] ip_rcv_finish+0x121/0x160 net/ipv4/ip_input.c:413 NF_HOOK include/linux/netfilter.h:305 [inline] NF_HOOK include/linux/netfilter.h:299 [inline] ip_rcv+0x18f/0x1a0 net/ipv4/ip_input.c:523 __netif_receive_skb_one_core+0xa7/0xe0 net/core/dev.c:5010 __netif_receive_skb+0x37/0xf0 net/core/dev.c:5124 process_backlog+0x1d3/0x420 net/core/dev.c:5955 read to 0xffff888102e40b58 of 8 bytes by task 13035 on cpu 1: __skb_wait_for_more_packets+0xfa/0x320 net/core/datagram.c:100 __skb_recv_udp+0x374/0x500 net/ipv4/udp.c:1683 udp_recvmsg+0xe1/0xb10 net/ipv4/udp.c:1712 inet_recvmsg+0xbb/0x250 net/ipv4/af_inet.c:838 sock_recvmsg_nosec+0x5c/0x70 net/socket.c:871 ___sys_recvmsg+0x1a0/0x3e0 net/socket.c:2480 do_recvmmsg+0x19a/0x5c0 net/socket.c:2601 __sys_recvmmsg+0x1ef/0x200 net/socket.c:2680 __do_sys_recvmmsg net/socket.c:2703 [inline] __se_sys_recvmmsg net/socket.c:2696 [inline] __x64_sys_recvmmsg+0x89/0xb0 net/socket.c:2696 do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Reported by Kernel Concurrency Sanitizer on: CPU: 1 PID: 13035 Comm: syz-executor.3 Not tainted 5.4.0-rc3+ #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Signed-off-by:
-
Eric Dumazet authored
Busy polling usually runs without locks. Let's use skb_queue_empty_lockless() instead of skb_queue_empty() Also uses READ_ONCE() in __skb_try_recv_datagram() to address a similar potential problem. Signed-off-by:
-
