- 16 Jan, 2013 22 commits
-
-
Stephen Hemminger authored
Use the standard netdev_xxx() and dev_xxx() wrappers to format log messages. Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Stephen Hemminger authored
Use netdev_dbg() rather than dev_dbg() because the former prints the device name which is more useful than the pci name. Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Stephen Hemminger authored
This messages that occur during boot time from this device when netdev_err is called before calling register_netdevice(). Switch to using dev_XXX macros which correlate message with PCI info which is available. Rather than fixing the features message, just remove it since the information is redundant and available through ethtool. Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Stephen Hemminger authored
The uncommitted[] array was set but never used except in a debug message. Remove it. Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Stephen Hemminger authored
Use netdev_alloc_skb_align, rather than open code using dev_alloc_skb. Change allocation at startup to use GFP_KERNEL. Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-nextDavid S. Miller authored
Jeff Kirsher says: ==================== This series contains updates to e1000e only. v2- updates patch 09/15 "e1000e: resolve checkpatch PREFER_PR_LEVEL warning" based on feedback from Joe Perches. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Bruce Allan authored
Cleanup a set of conditional tests. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Bruce Allan authored
The removed code block is duplicated in e1000e_write_itr() so use that instead. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Bruce Allan authored
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Bruce Allan authored
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Bruce Allan authored
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Bruce Allan authored
rx_long_byte_count can be removed since it is duplicated in rx_bytes Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Bruce Allan authored
WARNING: Prefer netdev_info(netdev, ... then dev_info(dev, ... then pr_info(... to printk(KERN_INFO ... v2 - remove unnecessary "e1000e:" prefix as pointed out by Joe Perches since that produces a redundant "e1000e:" in the log message Cc: Joe Perches <joe@perches.com> Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Bruce Allan authored
...discovered during code inspection. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Bruce Allan authored
When there is heavy traffic and the cable is pulled, the driver must reset the adapter to flush the Tx queue in hardware. This causes the reset path to be scheduled and logs the message "Reset adapter" which could be mis- interpreted as an error by the user. Change how the reset path is invoked for this scenario by using the same method done in an existing work-around for 80003es2lan (i.e. set a flag and if the flag is set in the reset code do not log the "Reset adapter" message since the reset is expected). Re-name the FLAG_RX_RESTART_NOW to FLAG_RESTART_NOW since it is used for resets in both the Rx and Tx specific code. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Bruce Allan authored
Energy Efficient Ethernet on 82579 and I217 should only be enabled if not disabled by the user, if the link is full duplex and the link partner has similar EEE capabilities (stored in different EMI registers on the two different parts). After enabling EEE, read the IEEE MMD register 3.1 (which is also stored in different EMI registers on the two different parts) to clear the count of received Tx/Rx LPI indications. Also, rename I217_EEE_100_SUPPORTED to I82579_EEE_100_SUPPORTED to indicate the bit is valid starting with I82579 (released before I217). Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Bruce Allan authored
When connected to certain switches, the 82577 PHY might drop link unexpectedly. Work around the issue by setting the Mean Square Error higher than the hardware default. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Bruce Allan authored
The Extended Management Interface (EMI) registers are accessed by first writing the EMI register offset to the EMI_ADDR regiter and then either reading or writing the data to/from the EMI_DATA register. Add helper functions for performing these steps and convert existing EMI register accesses accordingly. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Eric Dumazet authored
commit 1def9238 (net_sched: more precise pkt_len computation) does a wrong computation of mac + network headers length, as it includes the padding before the frame. Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Bruce Allan authored
On I217, the bit that indicates an invalid EEPROM (NVM) image checksum has changed from previous ICH/PCH LOMs. When validating the EEPROM checksum, check the appropriate bit on different devices. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Bruce Allan authored
When data blocks are written to the EEPROM, the HW/SW/FW semaphore must be held for the duration. With large data blocks on 80003es2lan, 82571 and 82572, this can take too long and cause the firmware to take ownership of the semaphore and consequently ownership of writes to the EEPROM. Instead, acquire and release the semaphore for each page of the block written. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Bruce Allan authored
Enables flow control to be set in SerDes autoneg mode. This is what is done for copper, but relies on a different set of register/bit checks since this is all done within the Mac registers. Remove inapplicable comment in defines.h Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 15 Jan, 2013 14 commits
-
-
Yuval Mintz authored
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yuval Mintz authored
Since submit 621b4d66 the bnx2x driver support FW GRO. However, when using the device with GRO enabled in bridging scenarios throughput is very low, as the bridge expects all incoming packets to be passed with CHECKSUM_PARTIAL - a demand which is satisfied by the SW GRO implementation, but was missed in the bnx2x driver implementation (which returned CHECKSUM_UNNECESSARY). Now, given that the traffic is supported by FW GRO (TCP/IP), the bnx2x driver calculates the pseudo checksum by itself, passing skbs with CHECKSUM_PARTIAL and giving a much better throughput when receiving GRO traffic. Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yuval Mintz authored
When enabling interrupts, acknowledge the interrupt only after configuring the IGU to the correct interrupt mode (otherwise it would dirty selftests) Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yuval Mintz authored
Get better control over interrupts during panic, and allow FW to test outgoing Tx packets when stop-on-error is allowed. Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Miriam Shitrit authored
This revises and enhances the bnx2x register dump facilities, adding support for `ethtool -w' on top of `ethtool -d'. Signed-off-by: Miriam Shitrit <miris@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yuval Mintz authored
When a device is configured to act as either iscsi or fcoe device in its nvram, prevent the other from being misused by preventing its activation in the driver. Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yaniv Rosner authored
On rare occasions, self test link may fail since the link is being sampled while it's still being stabilized. To correct this behaviour, try to sample the link for 2 seconds prior to declaring a failure. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Dmitry Kravkov authored
Current logic causes chips running in switch dependent multi-function FCoE mode not to configure their MAC, leading to an all 0s MAC. This patch configures the interface with the SAN Mac instead. Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Dmitry Kravkov authored
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yuval Mintz authored
Self-tests following boot from SAN have failed as the UNDI driver might leave some NIG interrupt indications. This patch does the clean-up, clearing those indications and allowing the test to pass. Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller authored
Conflicts: Documentation/networking/ip-sysctl.txt drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c Both conflicts were simply overlapping context. A build fix for qlcnic is in here too, simply removing the added devinit annotations which no longer exist. Signed-off-by: David S. Miller <davem@davemloft.net>
-
Nithin Nayak Sujir authored
TG3_PHY_AUXCTL_SMDSP_ENABLE/DISABLE macros do a blind write to the phy auxiliary control register and overwrite the EXT_PKT_LEN (bit 14) resulting in intermittent crc errors on jumbo frames with some link partners. Change the code to do a read/modify/write. Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Nithin Nayak Sujir authored
When netconsole is enabled, logging messages generated during tg3_open can result in a null pointer dereference for the uninitialized tg3 status block. Use the irq_sync flag to disable polling in the early stages. irq_sync is cleared when the driver is enabling interrupts after all initialization is completed. Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Paul Gortmaker authored
In commit a5e371f6 ("drivers/net: delete all code/drivers depending on CONFIG_MCA") most of the MCA drivers went, including the Kconfig/Makefile hooks for ibmlana, but it seems that I missed the "git rm" on these actual driver files, and with the namespace overlap with machine check architecture, it got missed by various git grep type checking done at that time. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 14 Jan, 2013 4 commits
-
-
git://1984.lsi.us.es/nfDavid S. Miller authored
Pablo Neira Ayuso says: ==================== The following patchset contains netfilter fixes for 3.8-rc3, they are: * fix possible BUG_ON if several netns are in use and the nf_conntrack module is removed, initial patch from Gao feng, final patch from myself. * fix unset return value if conntrack zone are disabled at compile-time, reported by Borislav Petkov, fix from myself. * fix display error message via dmesg for arp_tables, from Jan Engelhardt. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Paul Moore authored
This patch corrects some problems with LSM/SELinux that were introduced with the multiqueue patchset. The problem stems from the fact that the multiqueue work changed the relationship between the tun device and its associated socket; before the socket persisted for the life of the device, however after the multiqueue changes the socket only persisted for the life of the userspace connection (fd open). For non-persistent devices this is not an issue, but for persistent devices this can cause the tun device to lose its SELinux label. We correct this problem by adding an opaque LSM security blob to the tun device struct which allows us to have the LSM security state, e.g. SELinux labeling information, persist for the lifetime of the tun device. In the process we tweak the LSM hooks to work with this new approach to TUN device/socket labeling and introduce a new LSM hook, security_tun_dev_attach_queue(), to approve requests to attach to a TUN queue via TUNSETQUEUE. The SELinux code has been adjusted to match the new LSM hooks, the other LSMs do not make use of the LSM TUN controls. This patch makes use of the recently added "tun_socket:attach_queue" permission to restrict access to the TUNSETQUEUE operation. On older SELinux policies which do not define the "tun_socket:attach_queue" permission the access control decision for TUNSETQUEUE will be handled according to the SELinux policy's unknown permission setting. Signed-off-by: Paul Moore <pmoore@redhat.com> Acked-by: Eric Paris <eparis@parisplace.org> Tested-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Paul Moore authored
Add a new permission to align with the new TUN multiqueue support, "tun_socket:attach_queue". The corresponding SELinux reference policy patch is show below: diff --git a/policy/flask/access_vectors b/policy/flask/access_vectors index 28802c5..a0664a1 100644 --- a/policy/flask/access_vectors +++ b/policy/flask/access_vectors @@ -827,6 +827,9 @@ class kernel_service class tun_socket inherits socket +{ + attach_queue +} class x_pointer inherits x_device Signed-off-by: Paul Moore <pmoore@redhat.com> Acked-by: Eric Paris <eparis@parisplace.org> Tested-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
spin_is_locked() on a non !SMP build is kind of useless. BUG_ON(!spin_is_locked(xx)) is guaranteed to crash. Just remove this check in reqsk_fastopen_remove() as the callers do hold the socket lock. Reported-by: Ketan Kulkarni <ketkulka@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jerry Chu <hkchu@google.com> Cc: Yuchung Cheng <ycheng@google.com> Cc: Dave Taht <dave.taht@gmail.com> Acked-by: H.K. Jerry Chu <hkchu@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-