Skip to content

L
linux
Switch branch/tag
  1. 04 Mar, 2020 6 commits
    • Dajun Jin's avatar
      drivers/of/of_mdio.c:fix of_mdiobus_register() · 209c65b6
      Dajun Jin authored 
      When registers a phy_device successful, should terminate the loop
or the phy_device would be registered in other addr. If there are
multiple PHYs without reg properties, it will go wrong.
Signed-off-by: default avatarDajun Jin <adajunjin@gmail.com>
Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      209c65b6
    • Vishal Kulkarni's avatar
      cxgb4: fix checks for max queues to allocate · 116ca924
      Vishal Kulkarni authored 
      Hardware can support more than 8 queues currently limited by
netif_get_num_default_rss_queues(). So, rework and fix checks for max
number of queues to allocate. The checks should be based on how many are
actually supported by hardware, OR the number of online cpus; whichever
is lower.

Fixes: 5952dde7 ("cxgb4: set maximal number of default RSS queues")
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>"
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      116ca924
    • Hauke Mehrtens's avatar
      phylink: Improve error message when validate failed · 20d8bb0d
      Hauke Mehrtens authored 
      This should improve the error message when the PHY validate in the MAC
driver failed. I ran into this problem multiple times that I put wrong
interface values into the device tree and was searching why it is
failing with -22 (-EINVAL). This should make it easier to spot the
problem.
Signed-off-by: default avatarHauke Mehrtens <hauke@hauke-m.de>
Acked-by: default avatarRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      20d8bb0d
    • Jonas Gorski's avatar
      net: phy: bcm63xx: fix OOPS due to missing driver name · 43de81b0
      Jonas Gorski authored 
      719655a1 ("net: phy: Replace phy driver features u32 with link_mode
bitmap") was a bit over-eager and also removed the second phy driver's
name, resulting in a nasty OOPS on registration:

[    1.319854] CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 804dd50c, ra == 804dd4f0
[    1.330859] Oops[#1]:
[    1.333138] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.4.22 #0
[    1.339217] $ 0   : 00000000 00000001 87ca7f00 805c1874
[    1.344590] $ 4   : 00000000 00000047 00585000 8701f800
[    1.349965] $ 8   : 8701f800 804f4a5c 00000003 64726976
[    1.355341] $12   : 00000001 00000000 00000000 00000114
[    1.360718] $16   : 87ca7f80 00000000 00000000 80639fe4
[    1.366093] $20   : 00000002 00000000 806441d0 80b90000
[    1.371470] $24   : 00000000 00000000
[    1.376847] $28   : 87c1e000 87c1fda0 80b90000 804dd4f0
[    1.382224] Hi    : d1c8f8da
[    1.385180] Lo    : 5518a480
[    1.388182] epc   : 804dd50c kset_find_obj+0x3c/0x114
[    1.393345] ra    : 804dd4f0 kset_find_obj+0x20/0x114
[    1.398530] Status: 10008703 KERNEL EXL IE
[    1.402833] Cause : 00800008 (ExcCode 02)
[    1.406952] BadVA : 00000000
[    1.409913] PrId  : 0002a075 (Broadcom BMIPS4350)
[    1.414745] Modules linked in:
[    1.417895] Process swapper/0 (pid: 1, threadinfo=(ptrval), task=(ptrval), tls=00000000)
[    1.426214] Stack : 87cec000 80630000 80639370 80640658 80640000 80049af4 80639fe4 8063a0d8
[    1.434816]         8063a0d8 802ef078 00000002 00000000 806441d0 80b90000 8063a0d8 802ef114
[    1.443417]         87cea0de 87c1fde0 00000000 804de488 87cea000 8063a0d8 8063a0d8 80334e48
[    1.452018]         80640000 8063984c 80639bf4 00000000 8065de48 00000001 8063a0d8 80334ed0
[    1.460620]         806441d0 80b90000 80b90000 802ef164 8065dd70 80620000 80b90000 8065de58
[    1.469222]         ...
[    1.471734] Call Trace:
[    1.474255] [<804dd50c>] kset_find_obj+0x3c/0x114
[    1.479141] [<802ef078>] driver_find+0x1c/0x44
[    1.483665] [<802ef114>] driver_register+0x74/0x148
[    1.488719] [<80334e48>] phy_driver_register+0x9c/0xd0
[    1.493968] [<80334ed0>] phy_drivers_register+0x54/0xe8
[    1.499345] [<8001061c>] do_one_initcall+0x7c/0x1f4
[    1.504374] [<80644ed8>] kernel_init_freeable+0x1d4/0x2b4
[    1.509940] [<804f4e24>] kernel_init+0x10/0xf8
[    1.514502] [<80018e68>] ret_from_kernel_thread+0x14/0x1c
[    1.520040] Code: 1060000c  02202025  90650000 <90810000> 24630001  14250004  24840001  14a0fffb  90650000
[    1.530061]
[    1.531698] ---[ end trace d52f1717cd29bdc8 ]---

Fix it by readding the name.

Fixes: 719655a1 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Signed-off-by: default avatarJonas Gorski <jonas.gorski@gmail.com>
Acked-by: default avatarFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      43de81b0
    • Jacob Keller's avatar
      devlink: remove trigger command from devlink-region.rst · 70751834
      Jacob Keller authored 
      The devlink trigger command does not exist. While rewriting the
documentation for devlink into the reStructuredText format,
documentation for the trigger command was accidentally merged in. This
occurred because the author was also working on a potential extension to
devlink regions which included this trigger command, and accidentally
squashed the documentation incorrectly.

Further review eventually settled on using the previously unused "new"
command instead of creating a new trigger command.

Fix this by removing mention of the trigger command from the
documentation.

Fixes: 0b0f945f ("devlink: add a file documenting devlink regions", 2020-01-10)
Noticed-by: default avatarJiri Pirko <jiri@resnulli.us>
Signed-off-by: default avatarJacob Keller <jacob.e.keller@intel.com>
Reviewed-by: default avatarJiri Pirko <jiri@mellanox.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      70751834
    • Jonathan Neuschäfer's avatar
      docs: networking: net_failover: Fix a few typos · f8a0fea9
      Jonathan Neuschäfer authored 
      Signed-off-by: default avatarJonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      f8a0fea9
  3. 03 Mar, 2020 22 commits
  5. 02 Mar, 2020 4 commits
  7. 01 Mar, 2020 6 commits
    • Vladimir Oltean's avatar
      net: dsa: sja1105: Don't destroy not-yet-created xmit_worker · 52c0d4e3
      Vladimir Oltean authored 
      Fixes the following NULL pointer dereference on PHY connect error path
teardown:

[    2.291010] sja1105 spi0.1: Probed switch chip: SJA1105T
[    2.310044] sja1105 spi0.1: Enabled switch tagging
[    2.314970] fsl-gianfar soc:ethernet@2d90000 eth2: error -19 setting up slave phy
[    2.322463] 8<--- cut here ---
[    2.325497] Unable to handle kernel NULL pointer dereference at virtual address 00000018
[    2.333555] pgd = (ptrval)
[    2.336241] [00000018] *pgd=00000000
[    2.339797] Internal error: Oops: 5 [#1] SMP ARM
[    2.344384] Modules linked in:
[    2.347420] CPU: 1 PID: 64 Comm: kworker/1:1 Not tainted 5.5.0-rc5 #1
[    2.353820] Hardware name: Freescale LS1021A
[    2.358070] Workqueue: events deferred_probe_work_func
[    2.363182] PC is at kthread_destroy_worker+0x4/0x74
[    2.368117] LR is at sja1105_teardown+0x70/0xb4
[    2.372617] pc : [<c036cdd4>]    lr : [<c0b89238>]    psr: 60000013
[    2.378845] sp : eeac3d30  ip : eeab1900  fp : eef45480
[    2.384036] r10: eef4549c  r9 : 00000001  r8 : 00000000
[    2.389227] r7 : eef527c0  r6 : 00000034  r5 : ed8ddd0c  r4 : ed8ddc40
[    2.395714] r3 : 00000000  r2 : 00000000  r1 : eef4549c  r0 : 00000000
[    2.402204] Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
[    2.409297] Control: 10c5387d  Table: 8020406a  DAC: 00000051
[    2.415008] Process kworker/1:1 (pid: 64, stack limit = 0x(ptrval))
[    2.421237] Stack: (0xeeac3d30 to 0xeeac4000)
[    2.612635] [<c036cdd4>] (kthread_destroy_worker) from [<c0b89238>] (sja1105_teardown+0x70/0xb4)
[    2.621379] [<c0b89238>] (sja1105_teardown) from [<c10717fc>] (dsa_switch_teardown.part.1+0x48/0x74)
[    2.630467] [<c10717fc>] (dsa_switch_teardown.part.1) from [<c1072438>] (dsa_register_switch+0x8b0/0xbf4)
[    2.639984] [<c1072438>] (dsa_register_switch) from [<c0b89c30>] (sja1105_probe+0x2ac/0x464)
[    2.648378] [<c0b89c30>] (sja1105_probe) from [<c0b11a5c>] (spi_drv_probe+0x7c/0xa0)
[    2.656081] [<c0b11a5c>] (spi_drv_probe) from [<c0a26ab8>] (really_probe+0x208/0x480)
[    2.663871] [<c0a26ab8>] (really_probe) from [<c0a26f0c>] (driver_probe_device+0x78/0x1c4)
[    2.672093] [<c0a26f0c>] (driver_probe_device) from [<c0a24c48>] (bus_for_each_drv+0x80/0xc4)
[    2.680574] [<c0a24c48>] (bus_for_each_drv) from [<c0a26810>] (__device_attach+0xd0/0x168)
[    2.688794] [<c0a26810>] (__device_attach) from [<c0a259d8>] (bus_probe_device+0x84/0x8c)
[    2.696927] [<c0a259d8>] (bus_probe_device) from [<c0a25f24>] (deferred_probe_work_func+0x84/0xc4)
[    2.705842] [<c0a25f24>] (deferred_probe_work_func) from [<c03667b0>] (process_one_work+0x22c/0x560)
[    2.714926] [<c03667b0>] (process_one_work) from [<c0366d8c>] (worker_thread+0x2a8/0x5d4)
[    2.723059] [<c0366d8c>] (worker_thread) from [<c036cf94>] (kthread+0x150/0x154)
[    2.730416] [<c036cf94>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c)

Checking for NULL pointer is correct because the per-port xmit kernel
threads are created in sja1105_probe immediately after calling
dsa_register_switch.

Fixes: a68578c2 ("net: dsa: Make deferred_xmit private to sja1105")
Signed-off-by: default avatarVladimir Oltean <olteanv@gmail.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      52c0d4e3
    • Hangbin Liu's avatar
      net/ipv6: use configured metric when add peer route · 07758eb9
      Hangbin Liu authored 
      When we add peer address with metric configured, IPv4 could set the dest
metric correctly, but IPv6 do not. e.g.

]# ip addr add 192.0.2.1 peer 192.0.2.2/32 dev eth1 metric 20
]# ip route show dev eth1
192.0.2.2 proto kernel scope link src 192.0.2.1 metric 20
]# ip addr add 2001:db8::1 peer 2001:db8::2/128 dev eth1 metric 20
]# ip -6 route show dev eth1
2001:db8::1 proto kernel metric 20 pref medium
2001:db8::2 proto kernel metric 256 pref medium

Fix this by using configured metric instead of default one.
Reported-by: default avatarJianlin Shi <jishi@redhat.com>
Fixes: 8308f3ff ("net/ipv6: Add support for specifying metric of connected routes")
Reviewed-by: default avatarDavid Ahern <dsahern@gmail.com>
Signed-off-by: default avatarHangbin Liu <liuhangbin@gmail.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      07758eb9
    • Russell King's avatar
      net: dsa: mv88e6xxx: fix lockup on warm boot · 0395823b
      Russell King authored 
      If the switch is not hardware reset on a warm boot, interrupts can be
left enabled, and possibly pending. This will cause us to enter an
infinite loop trying to service an interrupt we are unable to handle,
thereby preventing the kernel from booting.

Ensure that the global 2 interrupt sources are disabled before we claim
the parent interrupt.

Observed on the ZII development revision B and C platforms with
reworked serdes support, and using reboot -f to reboot the platform.

Fixes: dc30c35b ("net: dsa: mv88e6xxx: Implement interrupt support.")
Signed-off-by: default avatarRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      0395823b
    • Randy Dunlap's avatar
      atm: nicstar: fix if-statement empty body warning · 8a171c5c
      Randy Dunlap authored 
      When debugging via PRINTK() is not enabled, make the PRINTK()
macro be an empty do-while block.

Thix fixes a gcc warning when -Wextra is set:
../drivers/atm/nicstar.c:1819:23: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body]

I have verified that there is no object code change (with gcc 7.5.0).
Signed-off-by: default avatarRandy Dunlap <rdunlap@infradead.org>
Cc: Chas Williams <3chas3@gmail.com>
Cc: linux-atm-general@lists.sourceforge.net
Cc: netdev@vger.kernel.org
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      8a171c5c
    • Pablo Neira Ayuso's avatar
      netlink: Use netlink header as base to calculate bad attribute offset · 84b32680
      Pablo Neira Ayuso authored 
      Userspace might send a batch that is composed of several netlink
messages. The netlink_ack() function must use the pointer to the netlink
header as base to calculate the bad attribute offset.

Fixes: 2d4bc933 ("netlink: extended ACK reporting")
Signed-off-by: default avatarPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      84b32680
    • You-Sheng Yang's avatar
      r8152: check disconnect status after long sleep · d64c7a08
      You-Sheng Yang authored 
      Dell USB Type C docking WD19/WD19DC attaches additional peripherals as:

  /: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/6p, 5000M
      |__ Port 1: Dev 11, If 0, Class=Hub, Driver=hub/4p, 5000M
          |__ Port 3: Dev 12, If 0, Class=Hub, Driver=hub/4p, 5000M
          |__ Port 4: Dev 13, If 0, Class=Vendor Specific Class,
              Driver=r8152, 5000M

where usb 2-1-3 is a hub connecting all USB Type-A/C ports on the dock.

When hotplugging such dock with additional usb devices already attached on
it, the probing process may reset usb 2.1 port, therefore r8152 ethernet
device is also reset. However, during r8152 device init there are several
for-loops that, when it's unable to retrieve hardware registers due to
being disconnected from USB, may take up to 14 seconds each in practice,
and that has to be completed before USB may re-enumerate devices on the
bus. As a result, devices attached to the dock will only be available
after nearly 1 minute after the dock was plugged in:

  [ 216.388290] [250] r8152 2-1.4:1.0: usb_probe_interface
  [ 216.388292] [250] r8152 2-1.4:1.0: usb_probe_interface - got id
  [ 258.830410] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): PHY not ready
  [ 258.830460] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): Invalid header when reading pass-thru MAC addr
  [ 258.830464] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): Get ether addr fail

This happens in, for example, r8153_init:

  static int generic_ocp_read(struct r8152 *tp, u16 index, u16 size,
			    void *data, u16 type)
  {
    if (test_bit(RTL8152_UNPLUG, &tp->flags))
      return -ENODEV;
    ...
  }

  static u16 ocp_read_word(struct r8152 *tp, u16 type, u16 index)
  {
    u32 data;
    ...
    generic_ocp_read(tp, index, sizeof(tmp), &tmp, type | byen);

    data = __le32_to_cpu(tmp);
    ...
    return (u16)data;
  }

  static void r8153_init(struct r8152 *tp)
  {
    ...
    if (test_bit(RTL8152_UNPLUG, &tp->flags))
      return;

    for (i = 0; i < 500; i++) {
      if (ocp_read_word(tp, MCU_TYPE_PLA, PLA_BOOT_CTRL) &
          AUTOLOAD_DONE)
        break;
      msleep(20);
    }
    ...
  }

Since ocp_read_word() doesn't check the return status of
generic_ocp_read(), and the only exit condition for the loop is to have
a match in the returned value, such loops will only ends after exceeding
its maximum runs when the device has been marked as disconnected, which
takes 500 * 20ms = 10 seconds in theory, 14 in practice.

To solve this long latency another test to RTL8152_UNPLUG flag should be
added after those 20ms sleep to skip unnecessary loops, so that the device
probe can complete early and proceed to parent port reset/reprobe process.

This can be reproduced on all kernel versions up to latest v5.6-rc2, but
after v5.5-rc7 the reproduce rate is dramatically lowered to 1/30 or less
while it was around 1/2.
Signed-off-by: default avatarYou-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      d64c7a08
  9. 28 Feb, 2020 1 commit
    • Linus Torvalds's avatar
      Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net · 7058b837
      Linus Torvalds authored 
      Pull networking fixes from David Miller:

 1) Fix leak in nl80211 AP start where we leak the ACL memory, from
    Johannes Berg.

 2) Fix double mutex unlock in mac80211, from Andrei Otcheretianski.

 3) Fix RCU stall in ipset, from Jozsef Kadlecsik.

 4) Fix devlink locking in devlink_dpipe_table_register, from Madhuparna
    Bhowmik.

 5) Fix race causing TX hang in ll_temac, from Esben Haabendal.

 6) Stale eth hdr pointer in br_dev_xmit(), from Nikolay Aleksandrov.

 7) Fix TX hash calculation bounds checking wrt. tc rules, from Amritha
    Nambiar.

 8) Size netlink responses properly in schedule action code to take into
    consideration TCA_ACT_FLAGS. From Jiri Pirko.

 9) Fix firmware paths for mscc PHY driver, from Antoine Tenart.

10) Don't register stmmac notifier multiple times, from Aaro Koskinen.

11) Various rmnet bug fixes, from Taehee Yoo.

12) Fix vsock deadlock in vsock transport release, from Stefano
    Garzarella.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (61 commits)
  net: dsa: mv88e6xxx: Fix masking of egress port
  mlxsw: pci: Wait longer before accessing the device after reset
  sfc: fix timestamp reconstruction at 16-bit rollover points
  vsock: fix potential deadlock in transport->release()
  unix: It's CONFIG_PROC_FS not CONFIG_PROCFS
  net: rmnet: fix packet forwarding in rmnet bridge mode
  net: rmnet: fix bridge mode bugs
  net: rmnet: use upper/lower device infrastructure
  net: rmnet: do not allow to change mux id if mux id is duplicated
  net: rmnet: remove rcu_read_lock in rmnet_force_unassociate_device()
  net: rmnet: fix suspicious RCU usage
  net: rmnet: fix NULL pointer dereference in rmnet_changelink()
  net: rmnet: fix NULL pointer dereference in rmnet_newlink()
  net: phy: marvell: don't interpret PHY status unless resolved
  mlx5: register lag notifier for init network namespace only
  unix: define and set show_fdinfo only if procfs is enabled
  hinic: fix a bug of rss configuration
  hinic: fix a bug of setting hw_ioctxt
  hinic: fix a irq affinity bug
  net/smc: check for valid ib_client_data
  ...
      7058b837
  11. 27 Feb, 2020 1 commit
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7