- 20 Nov, 2019 28 commits
-
-
Rahul Lakkireddy authored
Add TC-MATCHALL classifier ingress offload support. The same actions supported by existing TC-FLOWER offload can be applied to all incoming traffic on the underlying interface. Ensure the rule priority doesn't conflict with existing rules in the TCAM. Only 1 ingress matchall rule can be active at a time on the underlying interface. v5: - No change. v4: - Added check to ensure the matchall rule's prio doesn't conflict with other rules in TCAM. - Added logic to fill default mask for VIID, if none has been provided, to prevent conflict with duplicate VIID rules. - Used existing variables in private structure to fill VIID info, instead of extracting the info manually. v3: - No change. v2: - Removed logic to fetch free index from end of TCAM. Must maintain same ordering as in kernel. Signed-off-by:
Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Rahul Lakkireddy authored
Only offload rule if it satisfies both of the following conditions: 1. The immediate previous rule has priority <= current rule's priority. 2. The immediate next rule has priority >= current rule's priority. Also rework free entry fetch logic to search from end of TCAM, instead of beginning, because higher indices have lower priority than lower indices. This is similar to how TC auto generates priority values. v5: - Fixed commit message and comment to include comparison for equal priority. v4: - Patch added in this version. Signed-off-by:
-
Rahul Lakkireddy authored
Add TC-MATCHALL classifier offload with TC-POLICE action applied for all outgoing traffic on the underlying interface. Split flow block offload to support both egress and ingress classification. For example, to rate limit all outgoing traffic to 1 Gbps: $ tc qdisc add dev enp2s0f4 clsact $ tc filter add dev enp2s0f4 egress matchall skip_sw \ action police rate 1Gbit burst 8Kbit Note that skip_sw is important. Otherwise, both stack and hardware will end up doing policing. Policing can't be shared across flow blocks. Only 1 egress matchall rule can be active at a time on the underlying interface. v5: - No change. v4: - Removed check to reject police offload if prio is not 1. - Moved TC_SETUP_BLOCK code to separate function. v3: - Added check to reject police offload if prio is not 1. - Assign block_shared variable only for TC_SETUP_BLOCK. v2: - Added check to reject flow block sharing for policers. Signed-off-by:
-
David S. Miller authored
Saeed Mahameed says: ==================== page_pool: API for numa node change handling This series extends page pool API to allow page pool consumers to update page pool numa node on the fly. This is required since on some systems, rx rings irqs can migrate between numa nodes, due to irq balancer or user defined scripts, current page pool has no way to know of such migration and will keep allocating and holding on to pages from a wrong numa node, which is bad for the consumer performance. 1) Add API to update numa node id of the page pool Consumers will call this API to update the page pool numa node id. 2) Don't recycle non-reusable pages: Page pool will check upon page return whether a page is suitable for recycling or not. 2.1) when it belongs to a different num node. 2.2) when it was allocated under memory pressure. 3) mlx5 will use the new API to update page pool numa id on demand. The series is a joint work between me and Jonathan, we tested it and it proved itself worthy to avoid page allocator bottlenecks and improve packet rate and cpu utilization significantly for the described scenarios above. Performance testing: XDP drop/tx rate and TCP single/multi stream, on mlx5 driver while migrating rx ring irq from close to far numa: mlx5 internal page cache was locally disabled to get pure page pool results. CPU: Intel(R) Xeon(R) CPU E5-2603 v4 @ 1.70GHz NIC: Mellanox Technologies MT27700 Family [ConnectX-4] (100G) XDP Drop/TX single core: NUMA | XDP | Before | After --------------------------------------- Close | Drop | 11 Mpps | 10.9 Mpps Far | Drop | 4.4 Mpps | 5.8 Mpps Close | TX | 6.5 Mpps | 6.5 Mpps Far | TX | 3.5 Mpps | 4 Mpps Improvement is about 30% drop packet rate, 15% tx packet rate for numa far test. No degradation for numa close tests. TCP single/multi cpu/stream: NUMA | #cpu | Before | After -------------------------------------- Close | 1 | 18 Gbps | 18 Gbps Far | 1 | 15 Gbps | 18 Gbps Close | 12 | 80 Gbps | 80 Gbps Far | 12 | 68 Gbps | 80 Gbps In all test cases we see improvement for the far numa case, and no impact on the close numa case. ================== Performance analysis and conclusions by Jesper [1]: Impact on XDP drop x86_64 is inconclusive and shows only 0.3459ns slow-down, as this is below measurement accuracy of system. v2->v3: - Rebase on top of latest net-next and Jesper's page pool object release patchset [2] - No code changes - Performance analysis by Jesper added to the cover letter. v1->v2: - Drop last patch, as requested by Ilias and Jesper. - Fix documentation's performance numbers order. [1] https://github.com/xdp-project/xdp-project/blob/master/areas/mem/page_pool04_inflight_changes.org#performance-notes [2] https://patchwork.ozlabs.org/cover/1192098/ ==================== Acked-by:
Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by:
-
Saeed Mahameed authored
Once every napi poll cycle, check if numa node is different than the page pool's numa id, and update it using page_pool_update_nid(). Alternatively, we could have registered an irq affinity change handler, but page_pool_update_nid() must be called from napi context anyways, so the handler won't actually help. Performance testing: XDP drop/tx rate and TCP single/multi stream, on mlx5 driver while migrating rx ring irq from close to far numa: mlx5 internal page cache was locally disabled to get pure page pool results. CPU: Intel(R) Xeon(R) CPU E5-2603 v4 @ 1.70GHz NIC: Mellanox Technologies MT27700 Family [ConnectX-4] (100G) XDP Drop/TX single core: NUMA | XDP | Before | After --------------------------------------- Close | Drop | 11 Mpps | 10.9 Mpps Far | Drop | 4.4 Mpps | 5.8 Mpps Close | TX | 6.5 Mpps | 6.5 Mpps Far | TX | 3.5 Mpps | 4 Mpps Improvement is about 30% drop packet rate, 15% tx packet rate for numa far test. No degradation for numa close tests. TCP single/multi cpu/stream: NUMA | #cpu | Before | After -------------------------------------- Close | 1 | 18 Gbps | 18 Gbps Far | 1 | 15 Gbps | 18 Gbps Close | 12 | 80 Gbps | 80 Gbps Far | 12 | 68 Gbps | 80 Gbps In all test cases we see improvement for the far numa case, and no impact on the close numa case. Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Acked-by:
Jonathan Lemon <jonathan.lemon@gmail.com> Acked-by:
-
Saeed Mahameed authored
A page is NOT reusable when at least one of the following is true: 1) allocated when system was under some pressure. (page_is_pfmemalloc) 2) belongs to a different NUMA node than pool->p.nid. To update pool->p.nid users should call page_pool_update_nid(). Holding on to such pages in the pool will hurt the consumer performance when the pool migrates to a different numa node. Performance testing: XDP drop/tx rate and TCP single/multi stream, on mlx5 driver while migrating rx ring irq from close to far numa: mlx5 internal page cache was locally disabled to get pure page pool results. CPU: Intel(R) Xeon(R) CPU E5-2603 v4 @ 1.70GHz NIC: Mellanox Technologies MT27700 Family [ConnectX-4] (100G) XDP Drop/TX single core: NUMA | XDP | Before | After --------------------------------------- Close | Drop | 11 Mpps | 10.9 Mpps Far | Drop | 4.4 Mpps | 5.8 Mpps Close | TX | 6.5 Mpps | 6.5 Mpps Far | TX | 3.5 Mpps | 4 Mpps Improvement is about 30% drop packet rate, 15% tx packet rate for numa far test. No degradation for numa close tests. TCP single/multi cpu/stream: NUMA | #cpu | Before | After -------------------------------------- Close | 1 | 18 Gbps | 18 Gbps Far | 1 | 15 Gbps | 18 Gbps Close | 12 | 80 Gbps | 80 Gbps Far | 12 | 68 Gbps | 80 Gbps In all test cases we see improvement for the far numa case, and no impact on the close numa case. The impact of adding a check per page is very negligible, and shows no performance degradation whatsoever, also functionality wise it seems more correct and more robust for page pool to verify when pages should be recycled, since page pool can't guarantee where pages are coming from. Signed-off-by:
Ilias Apalodimas <ilias.apalodimas@linaro.org> Acked-by:
-
Saeed Mahameed authored
Add page_pool_update_nid() to be called by page pool consumers when they detect numa node changes. It will update the page pool nid value to start allocating from the new effective numa node. This is to mitigate page pool allocating pages from a wrong numa node, where the pool was originally allocated, and holding on to pages that belong to a different numa node, which causes performance degradation. For pages that are already being consumed and could be returned to the pool by the consumer, in next patch we will add a check per page to avoid recycling them back to the pool and return them to the page allocator. Signed-off-by:
-
David S. Miller authored
Grygorii Strashko says: ==================== net: ethernet: ti: introduce new cpsw switchdev based driver Thank you All for review of v6. There are no significant changes in this version, just fixed comments to v6. --- v6 The major change in this version is DT bindings conversation to json-schema, and fixed other comments to v5. Also added patch to clean up ALE on init and netif restart. --- v5 The major part of work done in this iteration is rebasing on top of net-next with XDP series from Ivan Khoronzhuk [3], and enable XDP support in the new CPSW switchdev driver (it was little bit painful ;(). There are mostly no functional changes in new CPSW driver, just few fixes, sync with old driver and cleanups/optimizations. So, I've kept rest of cover letter unchanged. --- This series originally based on work [1][2] done by Ilias Apalodimas <ilias.apalodimas@linaro.org>. This the RFC v5 which introduces new CPSW switchdev based driver which is operating in dual-emac mode by default, thus working as 2 individual network interfaces. The Switch mode can be enabled by configuring devlink driver parameter "switch_mode" to 1/true: devlink dev param set platform/48484000.switch \ name switch_mode value 1 cmode runtime This can be done regardless of the state of Port's netdev devices - UP/DOWN, but Port's netdev devices have to be in UP before joining the bridge to avoid overwriting of bridge configuration as CPSW switch driver completely reloads its configuration when first Port changes its state to UP. When the both interfaces joined the bridge - CPSW switch driver will start marking packets with offload_fwd_mark flag unless "ale_bypass=0". All configuration is implemented via switchdev API. The previous solution of tracking both Ports joined the bridge (from netdevice_notifier) proved to be not correct as changing CPSW switch driver mode required cleanup of ALE table and CPSW settings which happens while second Port is joined bridge and as result configuration loaded by bridge for the first Port became corrupted. The introduction of the new CPSW switchdev based driver (cpsw_new.c) is split on two parts: Part 1 - basic dual-emac driver; Part 2 switchdev support. Such approach has simplified code development and testing alot. And, I hope, it will help with better review. patches #1 - 5: preparation patches which also moves common code to cpsw_priv.c patches #6 - 9: Introduce TI CPSW switch driver based on switchdev and new DT bindings patch #10: new CPSW switchdev driver documentation patch #11: adds DT nodes for new CPSW switchdev driver added for DRA7 SoC patch #12: adds DT nodes for new cpsw switchdev driver for am571x-idk board patch #13: enables build of TI CPSW driver Most of the contents of the previous cover-letter have been added in new driver documentation, so please refer to that for configuration, testing and future work. These patches can be found at (branch contains some additional patches required for testing on top of net-next): https://github.com/grygoriyS/linux.git branch: lkml-5.4-switch-tbd-v7 changes in v7: - patch 2: added check for devm_kmalloc_array() return value - patch 6: fixed comments changes in v6: https://lkml.org/lkml/2019/11/9/108 - DT bindings converted to json-schema - netdev initialization is split on creation and registration. The netdevs registration happens now at the end of the pobe. - reworked cpsw_set_pauseparam() to use PHYlib APIs. - other comments for v5 fixed v5: https://patchwork.kernel.org/cover/11208785/ - rebase on top of net-next with XDP series from Ivan Khoronzhuk [3], and enable XDP support in the new CPSW switchdev driver cpsw driver (tested XDP_DROP only) - sync with old cpsw driver - implement comments from Ivan Khoronzhuk and Rob Herring - fixed "NETDEV WATCHDOG: .." warning after interface after interface UP/DOWN, missed TX wake in cpsw_adjust_link() v4: https://patchwork.kernel.org/cover/11010523/ - finished split of common CPSW code - added devlink support - changed CPSW mode configuration approach: from netdevice_notifier to devlink parameter - refactor and clean up ALE changes which allows to modify VLANs/MDBs entries - added missed support for port QDISC_CBS and QDISC_MQPRIO - the CPSW is split on two parts: basic dual_mac driver and switchdev support - added missed callback .ndo_get_port_parent_id() - reworked ingress frames marking in switch mode (offload_fwd_mark) - applied comments from Andrew Lunn v3: https://lwn.net/Articles/786677/ Changes in v3: - alot of work done to split properly common code between legacy and switchdev CPSW drivers and clean up code - CPSW switchdev interface updated to the current LKML switchdev interface - actually new CPSW switchdev based driver introduced - optimized dual_mac mode in new driver. Main change is that in promiscuous mode P0_UNI_FLOOD (both ports) is enabled in addition to ALLMULTI (current port) instead of ALE_BYPASS. So, port in non promiscuous mode will keep possibility of mcast and vlan filtering. - changed bridge join sequnce: now switch mode will be enabled only when both ports joined the bridge. CPSW will be switched to dual_mac mode if any port leave bridge. ALE table is completly cleared and then refiled while switching to switch mode - this simplidies code a lot, but introduces some limitation to bridge setup sequence: ip link add name br0 type bridge ip link set dev br0 type bridge ageing_time 1000 ip link set dev br0 type bridge vlan_filtering 0 <- disable echo 0 > /sys/class/net/br0/bridge/default_vlan ip link set dev sw0p1 up <- add ports ip link set dev sw0p2 up ip link set dev sw0p1 master br0 ip link set dev sw0p2 master br0 echo 1 > /sys/class/net/br0/bridge/default_vlan <- enable ip link set dev br0 type bridge vlan_filtering 1 bridge vlan add dev br0 vid 1 pvid untagged self - STP tested with vlan_filtering 1/0. To make STP work I've had to set NO_SA_UPDATE for all slave ports (see comment in code). It also required to statically register STP mcast address {0x01, 0x80, 0xc2, 0x0, 0x0, 0x0}; - allowed build both TI_CPSW and TI_CPSW_SWITCHDEV drivers - PTP can be enabled on both ports in dual_mac mode [1] https://patchwork.ozlabs.org/cover/929367/ [2] https://patches.linaro.org/cover/136709/ [3] https://patchwork.kernel.org/cover/11035813/ ==================== Signed-off-by:
-
Grygorii Strashko authored
Add CONFIG_TI_CPSW_SWITCHDEV option to enable new cpsw switchdev driver Signed-off-by:
Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by:
-
Grygorii Strashko authored
Add DT nodes for new cpsw switchdev driver for am571x-idk board for now to enable testing of the new solution. Signed-off-by:
-
Grygorii Strashko authored
Add DT nodes for new cpsw switch dev driver. Signed-off-by:
-
Ilias Apalodimas authored
A new cpsw dirver based on switchdev was added. Add documentation about basic configuration and future features Signed-off-by:
-
Grygorii Strashko authored
Add dependency from TI_CPSW_SWITCHDEV. Signed-off-by:
-
Ilias Apalodimas authored
CPSW switchdev based driver which is operating in dual-emac mode by default, thus working as 2 individual network interfaces. The Switch mode can be enabled by configuring devlink driver parameter "switch_mode" to 1: devlink dev param set platform/48484000.switch \ name switch_mode value 1 cmode runtime This can be done regardless of the state of Port's netdevs - UP/DOWN, but Port's netdev devices have to be UP before joining the bridge to avoid overwriting of bridge configuration as CPSW switch driver completely reloads its configuration when first Port changes its state to UP. When the both interfaces joined the bridge - CPSW switch driver will start marking packets with offload_fwd_mark flag unless "ale_bypass=0". All configuration is implemented via switchdev API and notifiers. Supported: - SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS - SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS: BR_MCAST_FLOOD - SWITCHDEV_ATTR_ID_PORT_STP_STATE - SWITCHDEV_OBJ_ID_PORT_VLAN - SWITCHDEV_OBJ_ID_PORT_MDB - SWITCHDEV_OBJ_ID_HOST_MDB Hence CPSW switchdev driver supports: - FDB offloading - MDB offloading - VLAN filtering and offloading - STP Signed-off-by:
-
Ilias Apalodimas authored
Part 1: Introduce basic CPSW dual_mac driver (cpsw_new.c) which is operating in dual-emac mode by default, thus working as 2 individual network interfaces. Main differences from legacy CPSW driver are: - optimized promiscuous mode: The P0_UNI_FLOOD (both ports) is enabled in addition to ALLMULTI (current port) instead of ALE_BYPASS. So, Ports in promiscuous mode will keep possibility of mcast and vlan filtering, which is provides significant benefits when ports are joined to the same bridge, but without enabling "switch" mode, or to different bridges. - learning disabled on ports as it make not too much sense for segregated ports - no forwarding in HW. - enabled basic support for devlink. devlink dev show platform/48484000.switch devlink dev param show platform/48484000.switch: name ale_bypass type driver-specific values: cmode runtime value false - "ale_bypass" devlink driver parameter allows to enable ALE_CONTROL(4).BYPASS mode for debug purposes. - updated DT bindings. Signed-off-by:
Murali Karicheri <m-karicheri2@ti.com> Signed-off-by:
-
Grygorii Strashko authored
Add bindings for the new TI CPSW switch driver. Comparing to the legacy bindings (net/cpsw.txt): - ports definition follows DSA bindings (net/dsa/dsa.txt) and ports can be marked as "disabled" if not physically wired. - all deprecated properties dropped; - all legacy propertiies dropped which represent constant HW cpapbilities (cpdma_channels, ale_entries, bd_ram_size, mac_control, slaves, active_slave) - TI CPTS DT properties are reused as is, but grouped in "cpts" sub-node - TI Davinci MDIO DT bindings are reused as is, because Davinci MDIO is reused. Signed-off-by:
-
Grygorii Strashko authored
As a preparatory patch to add support for a switchdev based cpsw driver, move common functions to cpsw-priv.c so that they can be used across both drivers. Signed-off-by:
-
Grygorii Strashko authored
A following patches introduce new CPSW switchdev driver which uses common code with legacy CPSW driver. This will introduce build dependency between CPSW switchdev and CPSW legacy drivers related to for_each_slave() and cpsw_slave_index() - they can be compiled both, but only one of them will be not functional depending in Kconfig settings due to duffrences in Slave Ports indexes calculation. To fix this make for_each_slave() local (it's used now only by legacy CPSW driver) and convert cpsw_slave_index() to be a function pointer which is assigned in probe. Driver to probe is defined by DT. Signed-off-by:
-
Ilias Apalodimas authored
A following patch introduces switchdev functionality, so modify ALE engine VLANs/MDBs API: - cpsw_ale_del_mcast(): update so it will remove only selected ports from mcast port_mask or delete whole mcast record if !port_mask - cpsw_ale_del_vlan(): update so it will remove only selected ports from all VLAN record's masks or delete whole VLAN record if !port_mask - add cpsw_ale_vlan_add_modify() to add or modify existing VLAN record's masks - add cpsw_ale_set_unreg_mcast() for enabling unreg mcast on port VLANs Signed-off-by:
-
Grygorii Strashko authored
Now untagged vlan traffic is not support on Host P0 port. This patch adds in ALE context bitmap of VLANs for which Host P0 port bit set in Force Untagged Packet Egress bitmask in VLANs ALE entries, and adds corresponding check in VLAN incapsulation header parsing function cpsw_rx_vlan_encap(). Signed-off-by:
-
Grygorii Strashko authored
Clean CPSW ALE on init and intf restart (up/down) to avoid reading obsolete or garbage entries from ALE table. Signed-off-by:
-
David S. Miller authored
Pablo Neira Ayuso says: ==================== nf_tables_offload: vlan matching support The following patchset contains Netfilter support for vlan matching offloads: 1) Constify nft_reg_load() as a preparation patch. 2) Restrict rule matching to ingress interface type ARPHRD_ETHER. 3) Add new vlan_tci field to flow_dissector_key_vlan structure, to allow to set up vlan_id, vlan_dei and vlan_priority in one go. 4) C-VLAN matching support. ==================== Signed-off-by: -
Pablo Neira Ayuso authored
Match on h_vlan_encapsulated_proto and set up protocol dependency. Check for protocol dependency before accessing the tci field. Allow to match on the encapsulated ethertype too. Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
Pablo Neira Ayuso authored
Match on ethertype and set up protocol dependency. Check for protocol dependency before accessing the tci field. Allow to match on the encapsulated ethertype too. Signed-off-by:
-
Pablo Neira Ayuso authored
Hardware offload support at this stage assumes an ethernet device in place. The flow dissector provides the intermediate representation to express this selector, so extend it to allow to store the interface type. Flower does not uses this, so skb_flow_dissect_meta() is not extended to match on this new field. Signed-off-by:
-
Pablo Neira Ayuso authored
This patch constifies the pointer to source register data that is passed as an input parameter. Signed-off-by:
-
Xin Long authored
geneve RFC (draft-ietf-nvo3-geneve-14) allows a geneve packet to carry multiple geneve opts, so it's necessary for lwtunnel to support adding multiple geneve opts in one lwtunnel route. But vxlan and erspan opts are still only allowed to add one option. With this patch, iproute2 could make it like: # ip r a 1.1.1.0/24 encap ip id 1 geneve_opts 0:0:12121212,1:2:12121212 \ dst 10.1.0.2 dev geneve1 # ip r a 1.1.1.0/24 encap ip id 1 vxlan_opts 456 \ dst 10.1.0.2 dev erspan1 # ip r a 1.1.1.0/24 encap ip id 1 erspan_opts 1:123:0:0 \ dst 10.1.0.2 dev erspan1 Which are pretty much like cls_flower and act_tunnel_key. Signed-off-by:Xin Long <lucien.xin@gmail.com> Signed-off-by:
-
Rahul Lakkireddy authored
Semicolon is not required at the end of switch block. So, remove it. Addresses coccinelle warning: drivers/net/ethernet/chelsio/cxgb4/sge.c:2260:2-3: Unneeded semicolon Fixes: 4846d533 ("cxgb4: add Tx and Rx path for ETHOFLD traffic") Reported-by:
kbuild test robot <lkp@intel.com> Signed-off-by:
-
- 19 Nov, 2019 12 commits
-
-
Vladimir Oltean authored
On the NXP LS1028A, there are 2 Ethernet links between the Felix switch and the ENETC: - eno2 <-> swp4, at 2.5G - eno3 <-> swp5, at 1G Only one of the above Ethernet port pairs can act as a DSA link for tagging. When adding initial support for the driver, it was tested only on the 1G eno3 <-> swp5 interface, due to the necessity of using PHYLIB initially (which treats fixed-link interfaces as emulated C22 PHYs, so it doesn't support fixed-link speeds higher than 1G). After making PHYLINK work, it appears that swp4 still can't act as CPU port. So it looks like ocelot_set_cpu_port was being called for swp4, but then it was called again for swp5, overwriting the CPU port assigned in the DT. It appears that when you call dsa_upstream_port for a port that is not defined in the device tree (such as swp5 when using swp4 as CPU port), its dp->cpu_dp pointer is not initialized by dsa_tree_setup_default_cpu, and this trips up the following condition in dsa_upstream_port: if (!cpu_dp) return port; So the moral of the story is: don't call dsa_upstream_port for a port that is not defined in the device tree, and therefore its dsa_port structure is not completely initialized (ds->num_ports is still 6). Fixes: 56051948 ("net: dsa: ocelot: add driver for Felix switch family") Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by:
-
Colin Ian King authored
In the case where the call to phy_interface_is_rgmii returns zero the variable ret is left uninitialized and this is returned at the end of the function dp83869_configure_rgmii. Fix this by returning 0 instead of the uninitialized value in ret. Addresses-Coverity: ("Uninitialized scalar variable") Fixes: 01db923e ("net: phy: dp83869: Add TI dp83869 phy") Signed-off-by:Colin Ian King <colin.king@canonical.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Xin Long authored
LWTUNNEL_IP_OPT_ERSPAN_VER is u8 type, and nla_put_u8 should have been used instead of nla_put_u32(). This is a copy-paste error. Fixes: b0a21810 ("lwtunnel: add options setting and dumping for erspan") Signed-off-by:
Simon Horman <simon.horman@netronome.com> Signed-off-by:
-
David S. Miller authored
Michael Chan says: ==================== bnxt_en: Updates. This series has the firmware interface update that changes the aRFS/ntuple interface on 57500 chips. The 2nd patch adds a counter and improves the hardware buffer error handling on the 57500 chips. The rest of the series is mainly enhancements on error recovery and firmware reset. ==================== Signed-off-by: -
Pavan Chebbi authored
This is especially beneficial during the NVRAM related firmware commands that have longer timeouts. If the BNXT_STATE_FW_FATAL_COND flag gets set while waiting for firmware response, abort and return error. Signed-off-by:
Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
-
Vasundhara Volam authored
During loss of heartbeat, log this warning message. Signed-off-by:
Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by:
-
Vasundhara Volam authored
For NVM params that are not supported in the current NVM configuration, return the error as -EOPNOTSUPP. Signed-off-by:
-
Vasundhara Volam authored
Report health status update to devlink health reporter, once reset is completed. Cc: Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
Vasundhara Volam authored
The Linux driver is capable of being the master function to handle resets, so we set the flag to let firmware know. Some other drivers, such as DPDK, is not capable and will not set the flag. Signed-off-by:
-
Vasundhara Volam authored
If firmware supports hot reset, extend ETHTOOL_RESET to support hot reset driver which does not require a driver reload after ETHTOOL_RESET. The driver will go through the same coordinated reset sequence as a firmware initiated fatal/non-fatal reset. Signed-off-by:
-
Vasundhara Volam authored
Use the larger HWRM_COREDUMP_TIMEOUT value for coredump related data response from the firmware. These commands take longer than normal commands. Signed-off-by:
-
Michael Chan authored
When hardware reports RX buffer errors, the latest 57500 chips do not require reset. The packet is discarded by the hardware and the ring will continue to operate. Also, add an rx_buf_errors counter for this type of error. It can help the user to identify if the aggregation ring is too small. Signed-off-by:
-
