On at least one laptop (ECS EF20EA) the 'hp-detect' GPIO is defined in
the DSDT table by the ACPI GpioIo resources in _CRS. The GPIO related
information should be mapped to the rt5645 driver to enable the jack
detection also on non-DT platforms.
Signed-off-by: Chris Chiu <chiu@endlessos.org>
Link: https://lore.kernel.org/r/20210111054141.4668-2-chiu@endlessos.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Because clk_disable_unprepare() already checked NULL clock parameter,
so the additional check is unnecessary, just remove it.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Link: https://lore.kernel.org/r/20210108085834.7168-1-vulab@iscas.ac.cnSigned-off-by: Mark Brown <broonie@kernel.org>

FE is connected to two BEs, BE1 is active, BE2 is deactive.
When closing BE1, FE/BE1 is in HW_FREE state, then BE2 is
startup by mixer runtime update.

For FE is in HW_FREE state, dpcm_run_update_startup() will skip
BE2's startup because FE's state is HW_FREE, BE2 stays in FE's
be_clients list.

During FE's closed, the dpcm_fe_dai_close() will close all related
BEs, BE2 will be closed. This will lead to BE2's dpcm[stream].users
mismatch.

We need disconnet all pending BEs in the corner case.
Signed-off-by: zhucancan <zhucancan@vivo.com>
Link: https://lore.kernel.org/r/AAoArwDfDnoefyxzy2wyiaqm.1.1608885766936.Hmail.zhucancan@vivo.comSigned-off-by: Mark Brown <broonie@kernel.org>

Remove a stale comment about SSP0 being untested, the
bytcht_es8316 has supported SSP0 for a while now and this has
been successfully tested on a GP electrinic T701 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210107120757.12051-1-hdegoede@redhat.comSigned-off-by: Mark Brown <broonie@kernel.org>

CPU support for TX49xx is getting removed, so remove sound support for it.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Link: https://lore.kernel.org/r/20210105140305.141401-11-tsbogend@alpha.franken.deSigned-off-by: Mark Brown <broonie@kernel.org>

bclk_ratio is unused.  Removes bclk_ratio and .set_bclk_ratio callback.

Removes snd_soc_dai_set_bclk_ratio() in a few machine drivers which are
obviously using rt1015.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20201224101854.3024823-1-tzungbi@google.comSigned-off-by: Mark Brown <broonie@kernel.org>

Assuming the calibration state gets lost after system suspend.
Re-calibrates again when resuming.

The rt1015_priv is alloced by kzalloc.  No need to initialize cali_done
to 0 in component probe callback.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20201225030845.4138497-1-tzungbi@google.comSigned-off-by: Mark Brown <broonie@kernel.org>

The newly added driver requires DMA support and fails to build
when that is disabled:

aarch64-linux-ld: sound/soc/fsl/fsl_aud2htx.o: in function `fsl_aud2htx_probe':
fsl_aud2htx.c:(.text+0x3e0): undefined reference to `imx_pcm_dma_init'

Fixes: 8a24c834 ("ASoC: fsl_aud2htx: Add aud2htx module driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/20210103135327.3630973-1-arnd@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The driver can request an optional clock for mclk.
Update the txt file to reflect this.
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201217162740.1452000-1-aford173@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Randconfig builds often show harmless warnings like

WARNING: unmet direct dependencies detected for SND_SOC_MT6359
  Depends on [n]: SOUND [=y] && !UML && SND [=y] && SND_SOC [=y] && MTK_PMIC_WRAP [=n]
  Selected by [y]:
  - SND_SOC_MT8192_MT6359_RT1015_RT5682 [=y] && SOUND [=y] && !UML && SND [=y] && SND_SOC [=y] && I2C [=y] && SND_SOC_MT8192 [=y]

Add a dependency to avoid that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20201230154345.639122-1-arnd@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Sparse will complain about trying to convert between values declared
as snd_ctl_elem_type_t and other types. This patch converts to
consistently use snd_ctl_elem_type_t for control type values. A __force
cast is needed in a couple of cases where the control type value is
parsed out of a DSP data block.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20201230172427.13865-2-rf@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

This fixes some minor cases where u32 or unsigned int types were used
to store big-endian data, and __be32 types used to store both big-endian
and cpu-endian data. This was producing sparse warnings.

Most cases resulted from using the same variable to hold the big-endian
value and its converted cpu-endian value. These can be simply fixed by
introducing another local variable, or avoiding storing the intermediate
value back into the original variable.

One special case is the raw_buf used in the compressed streams to transfer
data from DSP to user-side. The endian conversion happens in-place (as
there's no point introducing another buffer) so a cast to (__be32 *) is
added when passing it to wm_adsp_read_raw_data_block().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20201230172427.13865-1-rf@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

This patch removes the redundant delay time to speed up from the cold start
of headphone playback.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Link: https://lore.kernel.org/r/20201230080235.12698-1-oder_chiou@realtek.comSigned-off-by: Mark Brown <broonie@kernel.org>

The series refactors rt1015.c.

The 1st patch sorts header inclusions alphabetically.

The 2nd and 3rd patch improve error handling for kcontrols.

The 4th patch enhances readability.

The 5th patch removes unused variables in rt1015_priv.

Tzung-Bi Shih (5):
  ASoC: rt1015: sort header inclusions
  ASoC: rt1015: save boost_mode only if valid
  ASoC: rt1015: return error if any when setting bypass_boost
  ASoC: rt1015: refactor retry loop and rt1015_priv allocation
  ASoC: rt1015: remove unneeded variables in rt1015_priv

 sound/soc/codecs/rt1015.c | 49 ++++++++++++++++++++-------------------
 sound/soc/codecs/rt1015.h |  4 ----
 2 files changed, 25 insertions(+), 28 deletions(-)

--
2.29.2.729.g45daf8777d-goog

- `lrck' is only used in .hw_params callback so that it can be local.
- `bclk' is unused.
- `id' is unused.
- `amp_ver' is unused.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20201224100607.3006171-6-tzungbi@google.comSigned-off-by: Mark Brown <broonie@kernel.org>

Refactors retry loop in flush DAC work.  It is more clear to use a
for-loop here.

Uses !rt1015 to check if NULL.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20201224100607.3006171-5-tzungbi@google.comSigned-off-by: Mark Brown <broonie@kernel.org>

Returns -EBUSY if DAC is using when setting bypass_boost.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20201224100607.3006171-4-tzungbi@google.comSigned-off-by: Mark Brown <broonie@kernel.org>

Saves boost_mode only if valid.  Also returns -EINVAL if it is invalid.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20201224100607.3006171-3-tzungbi@google.comSigned-off-by: Mark Brown <broonie@kernel.org>

Sorts header inclusions.  ASCII value of 'r' is less than 's'.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20201224100607.3006171-2-tzungbi@google.comSigned-off-by: Mark Brown <broonie@kernel.org>

s/apci/acpi/

Turn an ICL into a TGL because it is likely a cut'n'paste error
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20201229085103.192715-1-christophe.jaillet@wanadoo.frSigned-off-by: Mark Brown <broonie@kernel.org>

Using a managed buffer will pre-allocate the buffer using
snd_pcm_lib_preallocate_pages() and automatically free it when the PCM is
destroyed.

In addition it will call snd_pcm_lib_malloc_pages() before the driver's
hw_params() callback and snd_pcm_lib_free_pages() after the driver's
hw_free() callback.

This slightly reduces the boilerplate code of the driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201218154544.25513-1-lars@metafoo.deSigned-off-by: Mark Brown <broonie@kernel.org>

Since we got list_entry_is_head() helper in the generic header,
we may switch driver to use it. This eliminates the need
in additional variable.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20201208111805.6989-1-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

New calibration sequence to fix power issue in idle state.
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Link: https://lore.kernel.org/r/ec66399502514edbb1de3cf9bff08b1d@realtek.comSigned-off-by: Mark Brown <broonie@kernel.org>

As the register map is 16-bit or 32-bit big-endian, the 24-bit
DSP words appear padded and with the bytes swapped. When reading a
raw stream of bytes, the pad bytes must be removed and the data bytes
swapped back to their original order.

The previous implementation of this assumed that the be32_to_cpu() in
wm_adsp_read_data_block() would swap back to little-endian. But this is
obviously only true on a little-endian CPU. It also made two walks
through the data, once to endian-swap and again to strip the pad bytes.

This patch re-works the code so that the endian-swap and unpad are done
together in a single walk, and it is not dependent on the endianness of
the CPU. The data_word_size argument to wm_adsp_remove_padding() has been
dropped because currently this is always 3.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20201216112512.26503-1-rf@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

Since we got list_entry_is_head() helper in the generic header,
we may switch catpt to use it. It removes the need in additional variable.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20201214172138.44267-1-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Since commit 36e2c742 ("fs: don't allow splice read/write without
explicit ops") we've required that file operation structures explicitly
enable splice support, rather than falling back to the default handlers.

Most /proc files use the indirect 'struct proc_ops' to describe their
file operations, and were fixed up to support splice earlier in commits
40be821d..b24c30c6, but the mountinfo files interact with the
VFS directly using their own 'struct file_operations' and got missed as
a result.

This adds the necessary support for splice to work for /proc/*/mountinfo
and friends.
Reported-by: Joan Bruguera Micó <joanbrugueram@gmail.com>
Reported-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209971
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull NTB fixes from Jon Mason:
 "Bug fix for IDT NTB and Intel NTB LTR management support"

* tag 'ntb-5.11' of git://github.com/jonmason/ntb:
  ntb: intel: add Intel NTB LTR vendor support for gen4 NTB
  ntb: idt: fix error check in ntb_hw_idt.c

Pull crypto fixes from Herbert Xu:
 "Fix a number of autobuild failures due to missing Kconfig
  dependencies"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: qat - add CRYPTO_AES to Kconfig dependencies
  crypto: keembay - Add dependency on HAS_IOMEM
  crypto: keembay - CRYPTO_DEV_KEEMBAY_OCS_AES_SM4 should depend on ARCH_KEEMBAY

Pull objtool fix from Ingo Molnar:
 "Fix a segfault that occurs when built with Clang"

* tag 'objtool-urgent-2020-12-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  objtool: Fix seg fault with Clang non-section symbols

Pull locking fixes from Ingo Molnar:
 "Misc fixes/updates:

   - Fix static keys usage in module __init sections

   - Add separate MAINTAINERS entry for static branches/calls

   - Fix lockdep splat with CONFIG_PREEMPTIRQ_EVENTS=y tracing"

* tag 'locking-urgent-2020-12-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  softirq: Avoid bad tracing / lockdep interaction
  jump_label/static_call: Add MAINTAINERS
  jump_label: Fix usage in module __init

Pull timer fixes from Ingo Molnar:
 "Update/fix two CPU sanity checks in the hotplug and the boot code, and
  fix a typo in the Kconfig help text.

  [ Context: the first two commits are the result of an ongoing
    annotation+review work of (intentional) tick_do_timer_cpu() data
    races reported by KCSAN, but the annotations aren't fully cooked
    yet ]"

* tag 'timers-urgent-2020-12-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timekeeping: Fix spelling mistake in Kconfig "fullfill" -> "fulfill"
  tick/sched: Remove bogus boot "safety" check
  tick: Remove pointless cpu valid check in hotplug code

Pull scheduler fix from Ingo Molnar:
 "Fix a context switch performance regression"

* tag 'sched-urgent-2020-12-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Optimize finish_lock_switch()

Commit c9a3c4e6 ("mfd: ab8500-debugfs: Remove extraneous curly
brace") removed a left-over curly brace that caused build failures, but
Joe Perches points out that the subsequent 'seq_putc()' should also be
removed, because the commit that caused all these problems already added
the final '\n' to the seq_printf() above it.
Reported-by: Joe Perches <joe@perches.com>
Fixes: 886c8121 ("mfd: ab8500-debugfs: Remove the racy fiddling with irq_desc")
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull PCI fixes from Bjorn Helgaas:

 - Fix a tegra enumeration regression (Rob Herring)

 - Fix a designware-host check that warned on *success*, not failure
   (Alexander Lobakin)

* tag 'pci-v5.11-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: dwc: Fix inverted condition of DMA mask setup warning
  PCI: tegra: Fix host link initialization

Clang errors:

  drivers/mfd/ab8500-debugfs.c:1526:2: error: non-void function does not return a value [-Werror,-Wreturn-type]
          }
          ^
  drivers/mfd/ab8500-debugfs.c:1528:2: error: expected identifier or '('
  return 0;
          ^
  drivers/mfd/ab8500-debugfs.c:1529:1: error: extraneous closing brace ('}')
  }
  ^
  3 errors generated.

The cleanup in ab8500_interrupts_show left a curly brace around, remove
it to fix the error.

Fixes: 886c8121 ("mfd: ab8500-debugfs: Remove the racy fiddling with irq_desc")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 660c4865 ("PCI: dwc: Set 32-bit DMA mask for MSI target address
allocation") added dma_mask_set() call to explicitly set 32-bit DMA mask
for MSI message mapping, but for now it throws a warning on ret == 0, while
dma_set_mask() returns 0 in case of success.

Fix this by inverting the condition.

[bhelgaas: join string to make it greppable]
Fixes: 660c4865 ("PCI: dwc: Set 32-bit DMA mask for MSI target address allocation")
Link: https://lore.kernel.org/r/20201222150708.67983-1-alobakin@pm.meSigned-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Commit b9ac0f9d ("PCI: dwc: Move dw_pcie_setup_rc() to DWC common
code") broke enumeration of downstream devices on Tegra:

In non-working case (next-20201211):

  0001:00:00.0 PCI bridge: NVIDIA Corporation Device 1ad2 (rev a1)
  0001:01:00.0 SATA controller: Marvell Technology Group Ltd. Device 9171 (rev 13)
  0005:00:00.0 PCI bridge: NVIDIA Corporation Device 1ad0 (rev a1)

In working case (v5.10-rc7):

  0001:00:00.0 PCI bridge: Molex Incorporated Device 1ad2 (rev a1)
  0001:01:00.0 SATA controller: Marvell Technology Group Ltd. Device 9171 (rev 13)
  0005:00:00.0 PCI bridge: Molex Incorporated Device 1ad0 (rev a1)
  0005:01:00.0 PCI bridge: PLX Technology, Inc. Device 3380 (rev ab)
  0005:02:02.0 PCI bridge: PLX Technology, Inc. Device 3380 (rev ab)
  0005:03:00.0 USB controller: PLX Technology, Inc. Device 3380 (rev ab)

The problem seems to be dw_pcie_setup_rc() is now called twice before and
after the link up handling. The fix is to move Tegra's link up handling to
.start_link() function like other DWC drivers. Tegra is a bit more
complicated than others as it re-inits the whole DWC controller to retry
the link. With this, the initialization ordering is restored to match the
prior sequence.

Fixes: b9ac0f9d ("PCI: dwc: Move dw_pcie_setup_rc() to DWC common code")
Link: https://lore.kernel.org/r/20201218143905.1614098-1-robh@kernel.orgReported-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Tested-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Vidya Sagar <vidyas@nvidia.com>

clang (quite rightly) complains fairly loudly about the newly added
mpc1_get_mpc_out_mux() function returning an uninitialized value if the
'opp_id' checks don't pass.

This may not happen in practice, but the code really shouldn't return
garbage if the sanity checks don't pass.

So just initialize 'val' to zero to avoid the issue.

Fixes: 110b055b ("drm/amd/display: add getter routine to retrieve mpcc mux")
Cc: Josip Pavic <Josip.Pavic@amd.com>
Cc: Bindu Ramamurthy <bindu.r@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>