We check tid->sched without a lock taken on ath_tx_aggr_sleep(). That
is race condition which can result of doing list_del(&tid->list) twice
(second time with poisoned list node) and cause crash like shown below:

[424271.637220] BUG: unable to handle kernel paging request at 00100104
[424271.637328] IP: [<f90fc072>] ath_tx_aggr_sleep+0x62/0xe0 [ath9k]
...
[424271.639953] Call Trace:
[424271.639998]  [<f90f6900>] ? ath9k_get_survey+0x110/0x110 [ath9k]
[424271.640083]  [<f90f6942>] ath9k_sta_notify+0x42/0x50 [ath9k]
[424271.640177]  [<f809cfef>] sta_ps_start+0x8f/0x1c0 [mac80211]
[424271.640258]  [<c10f730e>] ? free_compound_page+0x2e/0x40
[424271.640346]  [<f809e915>] ieee80211_rx_handlers+0x9d5/0x2340 [mac80211]
[424271.640437]  [<c112f048>] ? kmem_cache_free+0x1d8/0x1f0
[424271.640510]  [<c1345a84>] ? kfree_skbmem+0x34/0x90
[424271.640578]  [<c10fc23c>] ? put_page+0x2c/0x40
[424271.640640]  [<c1345a84>] ? kfree_skbmem+0x34/0x90
[424271.640706]  [<c1345a84>] ? kfree_skbmem+0x34/0x90
[424271.640787]  [<f809dde3>] ? ieee80211_rx_handlers_result+0x73/0x1d0 [mac80211]
[424271.640897]  [<f80a07a0>] ieee80211_prepare_and_rx_handle+0x520/0xad0 [mac80211]
[424271.641009]  [<f809e22d>] ? ieee80211_rx_handlers+0x2ed/0x2340 [mac80211]
[424271.641104]  [<c13846ce>] ? ip_output+0x7e/0xd0
[424271.641182]  [<f80a1057>] ieee80211_rx+0x307/0x7c0 [mac80211]
[424271.641266]  [<f90fa6ee>] ath_rx_tasklet+0x88e/0xf70 [ath9k]
[424271.641358]  [<f80a0f2c>] ? ieee80211_rx+0x1dc/0x7c0 [mac80211]
[424271.641445]  [<f90f82db>] ath9k_tasklet+0xcb/0x130 [ath9k]

Bug report:
https://bugzilla.kernel.org/show_bug.cgi?id=70551Reported-and-tested-by: Max Sydorenko <maxim.stargazer@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We are sending sleep confirm done interrupt in the middle of
sleep handshake. There is a corner case when Tx done interrupt
is received from firmware during sleep handshake due to which
host and firmware power states go out of sync causing cmd and
Tx data timeout problem.

Hence sleep confirm done interrupt is sent at the end of sleep
handshake to fix the problem.

Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We may get a NULL pointer here if skb allocation for Rx packet
was failed earlier.

Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Write io memory to clean PCIe buffer only when PCIe device is
present else this results into crash because of invalid memory
access.

Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Scan results from Marvell 8388 and 8686 have probe responses from
hidden APs and OLPC XO-1 mesh with a zero length SSID IE.

Bug in lbs_ret_scan discarded any remaining BSS in scan response,
leading to user not seeing APs in dense environments.

With LBS_DEB_SCAN, dmesg shows

libertas scan: scan response: 5 BSSs (419 bytes); resp size 474 bytes
libertas scan: scan: 00:1a:2b:84:de:e8, capa 0401, chan  1, qz, -51 dBm
libertas scan: scan: 5c:63:bf:d8:eb:0c, capa 0411, chan  1, qw129, -23 dBm
libertas scan: scan response: invalid IE fmt

With LBS_DEB_HEX, dmesg shows valid BSS in scan response were not
processed.

Change is to ignore zero length IE and continue processing.

Fixes OLPC 12757, http://dev.laptop.org/ticket/12757Signed-off-by: James Cameron <quozl@laptop.org>
Reported-by: T Gillett <tgillett@gmail.com>
Tested-by: T Gillett <tgillett@gmail.com>
CC: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Function del_timer() does not guarantee that timer was really deleted.
If the timer handler is beeing executed at the moment, the function
does nothing. So, it's possible to use already freed memory in the handler:

[ref: Documentation/DocBook/kernel-locking.tmpl]

This was found using grep and compile-tested only. Please, consider
applying or something similar to it.
Signed-off-by: Kirill Tkhai <ktkhai@parallels.com>
CC: Jouni Malinen <j@w1.fi>
CC: John W. Linville <linville@tuxdriver.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Consider the following (relatively unlikely) scenario:
 1) station goes to sleep while frames are buffered in driver
 2) driver blocks wakeup (until no more frames are buffered)
 3) station wakes up again
 4) driver unblocks wakeup

In this case, the current mac80211 code will do the following:
 1) WLAN_STA_PS_STA set
 2) WLAN_STA_PS_DRIVER set
 3) - nothing -
 4) WLAN_STA_PS_DRIVER cleared

As a result, no frames will be delivered to the client, even
though it is awake, until it sends another frame to us that
triggers ieee80211_sta_ps_deliver_wakeup() in sta_ps_end().

Since we now take the PS spinlock, we can fix this while at
the same time removing the complexity with the pending skb
queue function. This was broken since my commit 50a9432d
("mac80211: fix powersaving clients races") due to removing
the clearing of WLAN_STA_PS_STA in the RX path.

While at it, fix a cleanup path issue when a station is
removed while the driver is still blocking its wakeup.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There's a race condition in mac80211 because we add stations
to the internal lists after adding them to the driver, which
means that (for example) the following can happen:
 1. a station connects and is added
 2. first, it is added to the driver
 3. then, it is added to the mac80211 lists

If the station goes to sleep between steps 2 and 3, and the
firmware/hardware records it as being asleep, mac80211 will
never instruct the driver to wake it up again as it never
realized it went to sleep since the RX path discarded the
frame as a "spurious class 3 frame", no station entry was
present yet.

Fix this by adding the station in software first, and only
then adding it to the driver. That way, any state that the
driver changes will be reflected properly in mac80211's
station state. The problematic part is the roll-back if the
driver fails to add the station, in that case a bit more is
needed. To not make that overly complex prevent starting BA
sessions in the meantime.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There is a race between the TX path and the STA wakeup: while
a station is sleeping, mac80211 buffers frames until it wakes
up, then the frames are transmitted. However, the RX and TX
path are concurrent, so the packet indicating wakeup can be
processed while a packet is being transmitted.

This can lead to a situation where the buffered frames list
is emptied on the one side, while a frame is being added on
the other side, as the station is still seen as sleeping in
the TX path.

As a result, the newly added frame will not be send anytime
soon. It might be sent much later (and out of order) when the
station goes to sleep and wakes up the next time.

Additionally, it can lead to the crash below.

Fix all this by synchronising both paths with a new lock.
Both path are not fastpath since they handle PS situations.

In a later patch we'll remove the extra skb queue locks to
reduce locking overhead.

BUG: unable to handle kernel
NULL pointer dereference at 000000b0
IP: [<ff6f1791>] ieee80211_report_used_skb+0x11/0x3e0 [mac80211]
*pde = 00000000
Oops: 0000 [#1] SMP DEBUG_PAGEALLOC
EIP: 0060:[<ff6f1791>] EFLAGS: 00210282 CPU: 1
EIP is at ieee80211_report_used_skb+0x11/0x3e0 [mac80211]
EAX: e5900da0 EBX: 00000000 ECX: 00000001 EDX: 00000000
ESI: e41d00c0 EDI: e5900da0 EBP: ebe458e4 ESP: ebe458b0
 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
CR0: 8005003b CR2: 000000b0 CR3: 25a78000 CR4: 000407d0
DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
DR6: ffff0ff0 DR7: 00000400
Process iperf (pid: 3934, ti=ebe44000 task=e757c0b0 task.ti=ebe44000)
iwlwifi 0000:02:00.0: I iwl_pcie_enqueue_hcmd Sending command LQ_CMD (#4e), seq: 0x0903, 92 bytes at 3[3]:9
Stack:
 e403b32c ebe458c4 00200002 00200286 e403b338 ebe458cc c10960bb e5900da0
 ff76a6ec ebe458d8 00000000 e41d00c0 e5900da0 ebe458f0 ff6f1b75 e403b210
 ebe4598c ff723dc1 00000000 ff76a6ec e597c978 e403b758 00000002 00000002
Call Trace:
 [<ff6f1b75>] ieee80211_free_txskb+0x15/0x20 [mac80211]
 [<ff723dc1>] invoke_tx_handlers+0x1661/0x1780 [mac80211]
 [<ff7248a5>] ieee80211_tx+0x75/0x100 [mac80211]
 [<ff7249bf>] ieee80211_xmit+0x8f/0xc0 [mac80211]
 [<ff72550e>] ieee80211_subif_start_xmit+0x4fe/0xe20 [mac80211]
 [<c149ef70>] dev_hard_start_xmit+0x450/0x950
 [<c14b9aa9>] sch_direct_xmit+0xa9/0x250
 [<c14b9c9b>] __qdisc_run+0x4b/0x150
 [<c149f732>] dev_queue_xmit+0x2c2/0xca0

Cc: stable@vger.kernel.org
Reported-by: Yaara Rozenblum <yaara.rozenblum@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
[reword commit log, use a separate lock]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

After processing hint_user, we would want to schedule the
timeout work only if we are actually waiting to CRDA. This happens
when the status is not "IGNORE" nor "ALREADY_SET".
Signed-off-by: Inbal Hacohen <Inbal.Hacohen@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

remove_proc_subtree() doesn't work here as local->ddev has already
been removed, and NULLed out.  Use proc_remove() instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes regression caused by commit a16dad77 "MIPS: Fix
potencial corruption". That commit fixes one corruption scenario in
cost of adding another one, which actually start to cause crashes
on Yeeloong laptop when rtl8187 driver is used.

For correct DMA read operation on machines without DMA coherence, kernel
have to invalidate cache, such it will refill later with new data that
device wrote to memory, when that data is needed to process. We can only
invalidate full cache line. Hence when cache line includes both dma
buffer and some other data (written in cache, but not yet in main
memory), the other data can not hit memory due to invalidation. That
happen on rtl8187 where struct rtl8187_priv fields are located just
before and after small buffers that are passed to USB layer and DMA
is performed on them.

To fix the problem we align buffers and reserve space after them to make
them match cache line.

This patch does not resolve all possible MIPS problems entirely, for
that we have to assure that we always map cache aligned buffers for DMA,
what can be complex or even not possible. But patch fixes visible and
reproducible regression and seems other possible corruptions do not
happen in practice, since Yeeloong laptop works stable without rtl8187
driver.

Bug report:
https://bugzilla.kernel.org/show_bug.cgi?id=54391Reported-by: Petr Pisar <petr.pisar@atlas.cz>
Bisected-by: Tom Li <biergaizi2009@gmail.com>
Reported-and-tested-by: Tom Li <biergaizi2009@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Larry Finger <Larry.Finger@lwfinger.next>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In the original code we shift "AR5K_PHY(256) >> 28" which is zero but
the intent was to shift the return value of ath5k_hw_reg_read() like we
do a couple lines later.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl_ps_enable_nic() is called from loops that will loop until this function returns true or a
maximum number of retries is performed.

hw_init() returns non-zero on error. In that situation return false to
restore the original design intent to retry hw init when it fails.
Signed-off-by: Olivier Langlois <olivier@trillion01.com>
Cc: Stable <stable@vger.kernel.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl8192ce is disabling for too long the local interrupts during hw initiatialisation when performing scans

The observable symptoms in dmesg can be:

- underruns from ALSA playback
- clock freezes (tstamps do not change for several dmesg entries until irqs are finaly reenabled):

[  250.817669] rtlwifi:rtl_op_config():<0-0-0> 0x100
[  250.817685] rtl8192ce:_rtl92ce_phy_set_rf_power_state():<0-1-0> IPS Set eRf nic enable
[  250.817732] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[  250.817796] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[  250.817910] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[  250.818024] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[  250.818139] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[  250.818253] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[  250.818367] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[  250.818472] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[  250.818472] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[  250.818472] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[  250.818472] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[  250.818472] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:98053f15:10
[  250.818472] rtl8192ce:rtl92ce_sw_led_on():<0-1-0> LedAddr:4E ledpin=1
[  250.818472] rtl8192c_common:rtl92c_download_fw():<0-1-0> Firmware Version(49), Signature(0x88c1),Size(32)
[  250.818472] rtl8192ce:rtl92ce_enable_hw_security_config():<0-1-0> PairwiseEncAlgorithm = 0 GroupEncAlgorithm = 0
[  250.818472] rtl8192ce:rtl92ce_enable_hw_security_config():<0-1-0> The SECR-value cc
[  250.818472] rtl8192c_common:rtl92c_dm_check_txpower_tracking_thermal_meter():<0-1-0> Schedule TxPowerTracking direct call!!
[  250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> rtl92c_dm_txpower_tracking_callback_thermalmeter
[  250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> Readback Thermal Meter = 0xe pre thermal meter 0xf eeprom_thermalmeter 0xf
[  250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> Initial pathA ele_d reg0xc80 = 0x40000000, ofdm_index=0xc
[  250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> Initial reg0xa24 = 0x90e1317, cck_index=0xc, ch14 0
[  250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> Readback Thermal Meter = 0xe pre thermal meter 0xf eeprom_thermalmeter 0xf delta 0x1 delta_lck 0x0 delta_iqk 0x0
[  250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> <===
[  250.818472] rtl8192c_common:rtl92c_dm_initialize_txpower_tracking_thermalmeter():<0-1-0> pMgntInfo->txpower_tracking = 1
[  250.818472] rtl8192ce:rtl92ce_led_control():<0-1-0> ledaction 3
[  250.818472] rtl8192ce:rtl92ce_sw_led_on():<0-1-0> LedAddr:4E ledpin=1
[  250.818472] rtlwifi:rtl_ips_nic_on():<0-1-0> before spin_unlock_irqrestore
[  251.154656] PCM: Lost interrupts? [Q]-0 (stream=0, delta=15903, new_hw_ptr=293408, old_hw_ptr=277505)

The exact code flow that causes that is:

1. wpa_supplicant send a start_scan request to the nl80211 driver
2. mac80211 module call rtl_op_config with IEEE80211_CONF_CHANGE_IDLE
3.   rtl_ips_nic_on is called which disable local irqs
4.     rtl92c_phy_set_rf_power_state() is called
5.       rtl_ps_enable_nic() is called and hw_init()is executed and then the interrupts on the device are enabled

A good solution could be to refactor the code to avoid calling rtl92ce_hw_init() with the irqs disabled
but a quick and dirty solution that has proven to work is
to reenable the irqs during the function rtl92ce_hw_init().

I think that it is safe doing so since the device interrupt will only be enabled after the init function succeed.
Signed-off-by: Olivier Langlois <olivier@trillion01.com>
Cc: Stable <stable@vger.kernel.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

NICs supported by iwldvm don't handle well TX AMPDU.
Disable it by default, still leave the possibility to
the user to force enable it with a debug parameter.

NICs supported by iwlmvm don't suffer from the same issue,
leave TX AMPDU enabled by default for these.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Improves reliability of wifi connections with WPA, since authentication
frames are prioritized over normal traffic and also typically exempt
from aggregation.

Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In case ieee80211_prep_connection() fails to dereference
sdata->vif.chanctx_conf, the function returns and doesn't
free new_sta. fixed.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In case we were not suspended, the reconfig function returns without
configuring the scheduled scan.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Orignal code will not detect a DMA mapping failure, causing the HW
to attempt a DMA from an invalid address.

This patch add the error check and eventually simply drops the TX
packet if we can't map it for DMA.
Signed-off-by: andrea merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In original code the old RX DMA buffer is unmapped and processed and at the end
of the isr a new buffer is mapped with pci_map_single and attached to the RX
descriptor.

If pci_map_single fails then the RX descriptor remains with no valid DMA buffer
attached.
In this condition the DMA will target where it shouldn't with obvious evil
consequences.

Simply avoiding re-arming the descriptor will prevent buggy DMA but it will
result soon in RX stuck.

This patch move the DMA mapping of the new buffer at the beginning of the ISR
(and it adds error check for pci_map_single success/fail).

If the DMA mapping fails then we do not unmap the old buffer and we re-arm the
descriptor without processing it, with the old DMA buffer still attached.

In this way we lose the currently RX-ed packet, but whenever next calls to
pci_map_single will succeed again,then the RX process will go on without stuck.
Signed-off-by: andrea merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

During channel context assignment, the interface should
be found by interface iteration, so we need to assign the
pointer before the channel context.
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Tested-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The "new" fragmentation code (since my rewrite almost 5 years ago)
erroneously sets skb->len rather than using skb_trim() to adjust
the length of the first fragment after copying out all the others.
This leaves the skb tail pointer pointing to after where the data
originally ended, and thus causes the encryption MIC to be written
at that point, rather than where it belongs: immediately after the
data.

The impact of this is that if software encryption is done, then
 a) encryption doesn't work for the first fragment, the connection
    becomes unusable as the first fragment will never be properly
    verified at the receiver, the MIC is practically guaranteed to
    be wrong
 b) we leak up to 8 bytes of plaintext (!) of the packet out into
    the air

This is only mitigated by the fact that many devices are capable
of doing encryption in hardware, in which case this can't happen
as the tail pointer is irrelevant in that case. Additionally,
fragmentation is not used very frequently and would normally have
to be configured manually.

Fix this by using skb_trim() properly.

Cc: stable@vger.kernel.org
Fixes: 2de8e0d9 ("mac80211: rewrite fragmentation")
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Currently, when a station leaves an IBSS network, the
corresponding BSS is not dropped from cfg80211 if there are
other active stations in the network. But, the small
window that is present when trying to determine a station's
status based on IEEE80211_IBSS_MERGE_INTERVAL introduces
a race.

Instead of trying to keep the BSS, always remove it when
leaving an IBSS network. There is not much benefit to retain
the BSS entry since it will be added with a subsequent join
operation.

This fixes an issue where a dangling BSS entry causes ath9k
to wait for a beacon indefinitely.

Cc: <stable@vger.kernel.org>
Reported-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When the driver cannot start the AP or when the assignement
of the beacon goes wrong, we need to unassign the vif.

Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Due to the previous commit, when a scan finishes, it is in theory
possible to hit the following sequence:
 1. interface starts being removed
 2. scan is cancelled by driver and cfg80211 is notified
 3. scan done work is scheduled
 4. interface is removed completely, rdev->scan_req is freed,
    event sent to userspace but scan done work remains pending
 5. new scan is requested on another virtual interface
 6. scan done work runs, freeing the still-running scan

To fix this situation, hang on to the scan done message and block
new scans while that is the case, and only send the message from
the work function, regardless of whether the scan_req is already
freed from interface removal. This makes step 5 above impossible
and changes step 6 to be
 5. scan done work runs, sending the scan done message

As this can't work for wext, so we send the message immediately,
but this shouldn't be an issue since we still return -EBUSY.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When an interface/wdev is removed, any ongoing scan should be
cancelled by the driver. This will make it call cfg80211, which
only queues a work struct. If interface/wdev removal is quick
enough, this can leave the scan request pending and processed
only after the interface is gone, causing a use-after-free.

Fix this by making sure the scan request is not pending after
the interface is destroyed. We can't flush or cancel the work
item due to locking concerns, but when it'll run it shouldn't
find anything to do. This leaves a potential issue, if a new
scan gets requested before the work runs, it prematurely stops
the running scan, potentially causing another crash. I'll fix
that in the next patch.

This was particularly observed with P2P_DEVICE wdevs, likely
because freeing them is quicker than freeing netdevs.
Reported-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Fixes: 4a58e7c3 ("cfg80211: don't "leak" uncompleted scans")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

sdata->u.ap.request_smps_work can’t be flushed synchronously
under wdev_lock(wdev) since ieee80211_request_smps_ap_work
itself locks the same lock.
While at it, reset the driver_smps_mode when the ap is
stopped to its default: OFF.

This solves:

======================================================
[ INFO: possible circular locking dependency detected ]
3.12.0-ipeer+ #2 Tainted: G           O
-------------------------------------------------------
rmmod/2867 is trying to acquire lock:
  ((&sdata->u.ap.request_smps_work)){+.+...}, at: [<c105b8d0>] flush_work+0x0/0x90

but task is already holding lock:
  (&wdev->mtx){+.+.+.}, at: [<f9b32626>] cfg80211_stop_ap+0x26/0x230 [cfg80211]

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #1 (&wdev->mtx){+.+.+.}:
        [<c10aefa9>] lock_acquire+0x79/0xe0
        [<c1607a1a>] mutex_lock_nested+0x4a/0x360
        [<fb06288b>] ieee80211_request_smps_ap_work+0x2b/0x50 [mac80211]
        [<c105cdd8>] process_one_work+0x198/0x450
        [<c105d469>] worker_thread+0xf9/0x320
        [<c10669ff>] kthread+0x9f/0xb0
        [<c1613397>] ret_from_kernel_thread+0x1b/0x28

-> #0 ((&sdata->u.ap.request_smps_work)){+.+...}:
        [<c10ae9df>] __lock_acquire+0x183f/0x1910
        [<c10aefa9>] lock_acquire+0x79/0xe0
        [<c105b917>] flush_work+0x47/0x90
        [<c105d867>] __cancel_work_timer+0x67/0xe0
        [<c105d90f>] cancel_work_sync+0xf/0x20
        [<fb0765cc>] ieee80211_stop_ap+0x8c/0x340 [mac80211]
        [<f9b3268c>] cfg80211_stop_ap+0x8c/0x230 [cfg80211]
        [<f9b0d8f9>] cfg80211_leave+0x79/0x100 [cfg80211]
        [<f9b0da72>] cfg80211_netdev_notifier_call+0xf2/0x4f0 [cfg80211]
        [<c160f2c9>] notifier_call_chain+0x59/0x130
        [<c106c6de>] __raw_notifier_call_chain+0x1e/0x30
        [<c106c70f>] raw_notifier_call_chain+0x1f/0x30
        [<c14f8213>] call_netdevice_notifiers_info+0x33/0x70
        [<c14f8263>] call_netdevice_notifiers+0x13/0x20
        [<c14f82a4>] __dev_close_many+0x34/0xb0
        [<c14f83fe>] dev_close_many+0x6e/0xc0
        [<c14f9c77>] rollback_registered_many+0xa7/0x1f0
        [<c14f9dd4>] unregister_netdevice_many+0x14/0x60
        [<fb06f4d9>] ieee80211_remove_interfaces+0xe9/0x170 [mac80211]
        [<fb055116>] ieee80211_unregister_hw+0x56/0x110 [mac80211]
        [<fa3e9396>] iwl_op_mode_mvm_stop+0x26/0xe0 [iwlmvm]
        [<f9b9d8ca>] _iwl_op_mode_stop+0x3a/0x70 [iwlwifi]
        [<f9b9d96f>] iwl_opmode_deregister+0x6f/0x90 [iwlwifi]
        [<fa405179>] __exit_compat+0xd/0x19 [iwlmvm]
        [<c10b8bf9>] SyS_delete_module+0x179/0x2b0
        [<c1613421>] sysenter_do_call+0x12/0x32

Fixes: 687da132 ("mac80211: implement SMPS for AP")
Cc: <stable@vger.kernel.org> [3.13]
Reported-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Unfortunately I forgot this during the merge window, but the
patch seems small enough to go in as a fix. The userspace API
bug that was the reason for disabling it has long been fixed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When the netlink skb is exhausted split_start is left set. In the
subsequent retry, with a larger buffer, the dump is continued from the
failing point instead of from the beginning.

This was causing my rt28xx based USB dongle to now show up when
running "iw list" with an old iw version without split dump support.

Cc: stable@vger.kernel.org
Fixes: 3713b4e3 ("nl80211: allow splitting wiphy information in dumps")
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
[avoid the entire workaround when state->split is set]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

ieee80211_start_roc_work() might add a new roc
to existing roc, and tell cfg80211 it has already
started.

However, this might happen before the roc cookie
was set, resulting in REMAIN_ON_CHANNEL (started)
event with null cookie. Consequently, it can make
wpa_supplicant go out of sync.

Fix it by setting the roc cookie earlier.

Cc: stable@vger.kernel.org
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The commit, "ath9k_hw: Fix incorrect Tx control power in AR9003 template"
fixed the incorrect values in the eeprom templates, but if
boards have already been calibrated with incorrect values,
they would still be using the wrong TX power. Fix this by assigning
a default value in such cases.

Cc: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Even though we make sure PowerSave is not enabled by default
by disabling the flag, WIPHY_FLAG_PS_ON_BY_DEFAULT on init,
PS could be enabled by userspace based on various factors
like battery usage etc. Since PS in ath9k is just broken
and has been untested for years, remove support for it, but
allow a user to explicitly enable it using a module parameter.

Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use mdelay instead of udelay to fix this error:

ERROR: "__bad_udelay" [drivers/net/wireless/ath/ath9k/ath9k_hw.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
Reported-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211 ->sta_rc_update() callback must be atomic. Since we have to
take mutex and do other operations that can sleep when sending fimrware
commands to device, the only option to satisfy atomicity requirement of
->sta_rc_update(), that I can see, is introduce work_struct and defer
uploading new rates to that work.
Tested-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Raw id and FW id should be switched.
Tested-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It is a copy/paste of patch provided by Sujith for ath9k.

"Even though we make sure PowerSave is not enabled by default
by disabling the flag, WIPHY_FLAG_PS_ON_BY_DEFAULT on init,
PS could be enabled by userspace based on various factors
like battery usage etc. Since PS in ath9k is just broken
and has been untested for years, remove support for it, but
allow a user to explicitly enable it using a module parameter."

Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>