- 27 Jun, 2013 1 commit
-
-
Wei Yongjun authored
There is a error message within devm_ioremap_resource already, so remove the dev_err call to avoid redundant error message. Signed-off-by:
Wei Yongjun <yongjun_wei@trendmicro.com.cn> Acked-by:
Tony Prisk <linux@prisktech.co.nz> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org>
-
- 25 Jun, 2013 5 commits
-
-
Heiko Stübner authored
Some options currently take arguments in unspecified driver-specific units. As pointed out by Stephen Warren, driver specific values should not be part of generic devicetree bindings describing the hardware. Therefore remove the critical bindings again, before they become part of an official release. Signed-off-by:
Heiko Stuebner <heiko@sntech.de> Reviewed-by:
James Hogan <james.hogan@imgtec.com> Signed-off-by:
-
Heiko Stübner authored
As the binding for slew-rate is under discussion and seems to need more tought it will get removed for now, so it doesn't get an offical release. Therefore remove it again from the only current user, tz1090. Signed-off-by:
-
Heiko Stübner authored
Currently the debounce time pinconfig option uses an unspecified "time units" unit. As pinconfig options should use SI units and a real unit is also necessary for generic dt bindings, change it to usec. Currently no driver is using the generic pinconfig option for this, so the unit change is safe to do. Signed-off-by:
-
Heiko Stübner authored
PULL_PIN_DEFAULT is meant for hardware completely hiding any pull settings from the driver, so that it's really only possible to turn the pull on or off, but it not being possible to determine any pull settings from software. Also the binding-documentation for the pull arguments did not match the changes to the expected values. Signed-off-by:
-
Linus Walleij authored
From the inception ot the pin config API there has been the possibility to get a handle at a pin directly and configure its electrical characteristics. For this reason we had: int pin_config_get(const char *dev_name, const char *name, unsigned long *config); int pin_config_set(const char *dev_name, const char *name, unsigned long config); int pin_config_group_get(const char *dev_name, const char *pin_group, unsigned long *config); int pin_config_group_set(const char *dev_name, const char *pin_group, unsigned long config); After the introduction of the pin control states that will control pins associated with devices, and its subsequent introduction to the device core, as well as the introduction of pin control hogs that can set up states on boot and optionally also at sleep, this direct pin control API is a thing of the past. As could be expected, it has zero in-kernel users. Let's delete this API and make our world simpler. Reported-by:Tony Lindgren <tony@atomide.com> Reviewed-by:
Stephen Warren <swarren@nvidia.com> Acked-by:
-
- 24 Jun, 2013 11 commits
-
-
James Hogan authored
Add a pin control driver for the TZ1090's low power pins via the powerdown controller SOC_GPIO_CONTROL registers. These pins have individually controlled pull-up, and group controlled schmitt, slew-rate, drive-strength, and power-on-start (pos). The pdc_gpio0 and pdc_gpio1 pins can also be muxed onto the ir_mod_stable_out and ir_mod_power_out functions respectively. If no function is set they remain in GPIO mode. These muxes can be overridden by requesting them as GPIOs. Signed-off-by:
-
James Hogan authored
Add a pin control driver for the main pins on the TZ1090 SoC. This doesn't include the low-power pins as they're controlled separately via the Powerdown Controller (PDC) registers. Signed-off-by:
-
Sachin Kamat authored
'drvdata_list' is used only in this file. Make it static. Signed-off-by:
Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by:
-
Axel Lin authored
Signed-off-by:
Axel Lin <axel.lin@ingics.com> Acked-by:
-
Patrice Chotard authored
At several places, return value was not tested and error output was missing. Signed-off-by:
Patrice Chotard <patrice.chotard@st.com> Signed-off-by:
-
Patrice Chotard authored
Replace hardcoded value by corresponding #define's. Signed-off-by:
-
Patrice Chotard authored
Factorize code by adding abx500_pullud_supported() which improve code readability. Signed-off-by:
-
Patrice Chotard authored
- allow to get output GPIO value - as there is no GPIO0 on ABX500, use correct offset with abx500_gpio_get_bit() Signed-off-by:
-
Patrice Chotard authored
- Update abx500_pin_config_set() in order to take in account PIN_CONFIG_BIAS_DISABLE state to disable pull up or pull down. - Rework error path. Signed-off-by:
-
Patrice Chotard authored
We use the same way to define pin muxing and pin configuration than for nomadik. So pickup code from pinctrl_nomadik.c to be able to implement pin multiplexing and pin configuration using the device tree. Pin configuration uses generic parsing code. Signed-off-by:
Gabriel Fernandez <gabriel.fernandez@st.com> Signed-off-by:
-
Laurent Pinchart authored
Fix a compilation error caused by pinconf_generic_parse_dt_config() not being defined on !CONFIG_OF platforms by guarding the whole DT node parsing code with #ifdef CONFIG_OF. Defining a pinconf_generic_parse_dt_config() on !CONFIG_OF would have been possible as well, but would have resulted in a larger code size on !CONFIG_OF platforms (such as arch/sh). Signed-off-by:
Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by:
Simon Horman <horms+renesas@verge.net.au> Signed-off-by:
-
- 18 Jun, 2013 10 commits
-
-
Mathias Nyman authored
Add support for gpio on Intel BayTrail platforms. BayTrail supports 3 banks of gpios called SCORE, NCORE ans SUS with 102, 28 and 44 gpio pins. Supports gpio interrupts and ACPI gpio events Pins may be muxed to alternate function instead of gpio by firmware. This driver does not touch the pin muxing and expect firmare to set pin muxing and pullup/down properties properly. Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
James Hogan authored
The kerneldoc comment for struct pinconf_ops was missing pin_config_dbg_parse_modify, and instead described pin_config_group_dbg_set (which is presumably an old name for the same function). Rename it in the kerneldoc comment so they match. Signed-off-by:
-
Sachin Kamat authored
Symbols referenced only in this file are made static. Signed-off-by:
-
Sachin Kamat authored
'spear310_o2p' is referenced only in this file. Signed-off-by:
Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by:
-
Sachin Kamat authored
Some symbols referenced only in this file are made static. Signed-off-by:
-
Sachin Kamat authored
'bcm2835_gpio_pins' is used only in this file. Signed-off-by:
-
Laurent Pinchart authored
Signed-off-by:
-
Laurent Pinchart authored
Support device instantiation through the device tree. The compatible property is used to select the SoC pinmux information. Set the gpio_chip device field to the PFC device to enable automatic GPIO OF support. Cc: devicetree-discuss@lists.ozlabs.org Signed-off-by:
-
Laurent Pinchart authored
Platform data isn't used, support can thus be removed. Signed-off-by:
-
Wei Yongjun authored
Add the missing unlock before return from function pinctrl_find_gpio_range_from_pin() in the error handling case. Introduced by commit 2ff3477efd7086544b9e298fc63afab0645921b4. (pinctrl: add pin list based GPIO ranges) Signed-off-by:
-
- 17 Jun, 2013 13 commits
-
-
Doug Anderson authored
A level-triggered interrupt should be acked after the interrupt line becomes inactive and before it is unmasked, or else another interrupt will be immediately triggered. Acking before or after calling the handler is not enough. Signed-off-by:
Luigi Semenzato <semenzato@chromium.org> Signed-off-by:
Doug Anderson <dianders@chromium.org> Acked-by:
Tomasz Figa <t.figa@samsung.com> Signed-off-by:
-
Doug Anderson authored
It's convenient if get_maintainer suggests sending samsung/exynos pinctrl changes to linux-samsung-soc and to Tomasz and Thomas. Signed-off-by:
Kyungmin Park <kyungmin.park@samsung.com> Acked-by:
Olof Johansson <olof@lixom.net> Acked-by:
Kukjin Kim <kgene.kim@samsung.com> Signed-off-by:
-
Arnd Bergmann authored
The three functions pinctrl_pm_select_default_state, pinctrl_pm_select_sleep_state, and pinctrl_pm_select_idle_state are used in drivers that can be loadable modules, and should be exported. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Heiko Stübner authored
Change the rockchip pinctrl driver to handle the arguments to the pull pinconfig options correctly. So only accept non-0 values for the pull options as the rockchip pin-controller can only turn pulls on and off (this via BIAS_DISABLE). Signed-off-by:
-
Hebbar Gururaja authored
Make pinctrl-single able to handle suspend/resume events and change hogged pins states accordingly. Signed-off-by:
Hebbar Gururaja <gururaja.hebbar@ti.com> Acked-by:
-
Fabio Baltieri authored
Removes the warnings: drivers/spi/spi-pl022.c: In function 'pl022_suspend_resources': drivers/spi/spi-pl022.c:2322:24: warning: unused variable 'pins_state' [-Wunused-variable] drivers/spi/spi-pl022.c:2321:6: warning: unused variable 'ret' [-Wunused-variable] drivers/spi/spi-pl022.c: In function 'pl022_resume_resources': drivers/spi/spi-pl022.c:2334:6: warning: unused variable 'ret' [-Wunused-variable] introduced in: f1c9cf07 spi: pl022: use pinctrl PM helpers Signed-off-by:
Fabio Baltieri <fabio.baltieri@linaro.org> Acked-by:
Mark Brown <broonie@linaro.org> Signed-off-by:
-
Maxime Ripard authored
Signed-off-by:
Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by:
-
Maxime Ripard authored
It will allow us to have a cleaner separation between the data needed by the driver to work, and the core logic of the driver in itself, and will allow having too much noise in the core driver in the future. Signed-off-by:
-
Linus Walleij authored
It is counter-intuitive to have "0" mean disable in a boolean manner for electronic properties of pins such as pull-up and pull-down. Therefore, define that a pull-up/pull-down argument of 0 to such a generic option means that the pin is short-circuited to VDD or GROUND. Pull disablement shall be done using PIN_CONFIG_BIAS_DISABLE. Cc: James Hogan <james.hogan@imgtec.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by Heiko Stuebner <heiko@sntech.de> Acked-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Heiko Stübner authored
Allocating the temorary array in pinconf_generic_parse_dt_config on stack might cause problems later on, when the number of options grows over time. Therefore also allocate this array dynamically to be on the safe side. Suggested-by:
-
Heiko Stübner authored
This adds a shortcut when no valid pinconf properties are found in the parsed dt node, to set the values immediately and return. Suggested-by:
-
Heiko Stübner authored
The bias-pull-* options use values > 0 to indicate that the pull should be activated and optionally also indicate the strength of the pull. Therefore use an default value of 1 for these options. Split the low-power-mode option into low-power-enable and -disable. Update the documentation to describe the param arguments better. Reported-by:
-
Christian Ruppert authored
The comment introduced with the recently added pinctrl_gpio_range.pins element was wrong. This corrects it. Thanks to Patrice Chotard for pointing this out. Signed-off-by:
Christian Ruppert <christian.ruppert@abilis.com> Signed-off-by:
-
