OrangePi 3 can optionally have 8 GiB eMMC (soldered on board). Because
those pins are dedicated to eMMC exclusively, node can be added for both
variants (with and without eMMC). Kernel will then scan bus for presence
of eMMC and act accordingly.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

A64 contains deinterlace core, compatible to the one found in H3.
It can be used in combination with VPU unit to decode and process
interlaced videos.

Add a node for it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

Allwinner A64 SoC also contains deinterlace core, compatible to H3.

Add compatible string for it.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

A64 contains MBUS, which is the bus used by DMA devices to access
system memory.

MBUS controller is responsible for arbitration between channels based
on set priority and can do some other things as well, like report
bandwidth used. It also maps RAM region to different address than CPU.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

A64 contains MBUS controller. Add a compatible for it.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

There are two sensors, sensor0 for CPU, sensor1 for GPU.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

Add the regulators for each bank on this boards.
For VCC-PL only add a comment on what regulator is used. We cannot add
the property without causing a circular dependency as the PL pins are
used to talk to the PMIC.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

Now that AXP803 GPIO support is available, we can properly model
the hardware. Replace the use of GPIO0-LDO with a fixed regulator
controlled by GPIO0. This boost regulator is used to power the
(internal and external) USB ports, as well as the speakers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

The output from the backlight regulator is labeled as "VBKLT" in the
schematic. Using the equation and resistor values from the schematic,
the output is approximately 18V, not 3.3V. Since the regulator in use
(SS6640STR) is a boost regulator powered by PS (battery or AC input),
which are both >3.3V, the output could not be 3.3V anyway.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

Allwinner A64 SoC has separate supplies for PC, PD, PE, PG and PL.

VCC-PC and VCC-PG are supplied by ELDO1 at 1.8v.
VCC-PD is supplied by DCDC1 (VCC-IO) at 3.3v.
VCC-PE is supplied by ALDO1, and is unused.

VCC-PL creates a circular dependency, so it is omitted for now.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

Normally GPIO pin references are followed by a comment giving the pin
name for searchability. Add the comment here where it was missing.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

Boards generally reference the simplefb nodes from the SoC dtsi by
label, not by full path. simplefb_hdmi is already like this in the
Pinebook DTS. Update simplefb_lcd to match.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

The r_i2c node should come before r_rsb, and in any case should not
separate the axp803 node from its subnodes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

This fixed regulator has no consumers, GPIOs, or other connections.
Remove it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

The Orange Pi PC2 features a GPIO button. As the button is connected to
Port L (pin PL3), it can be used as a wakeup source. Enable this.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

PineTab is a 10.1" tablet by Pine64 with Allwinner A64 inside.

It includes the following peripherals:

USB:
- A microUSB Type-B port connected to the OTG-capable USB PHY of
Allwinner A64. The ID pin is connected to a GPIO of the A64 SoC, and the
Vbus is connected to the Vbus of AXP803 PMIC. These enables OTG
functionality on this port.
- A USB Type-A port is connected to the internal hub attached to the
non-OTG USB PHY of Allwinner A64.
- There are reserved pins for an external keyboard connected to the
internal hub.

Power:
- The microUSB port has its Vbus connected to AXP803, mentioned above.
- A DC jack (of a strange size, 2.5mm outer diameter) is connected to
the ACIN of AXP803.
- A Li-Polymer battery is connected to the battery pins of AXP803.

Storage:
- An tradition Pine64 eMMC slot is on the board, mounted with an eMMC
module by factory.
- An external microSD slot is hidden under a protect case.

Display:
- A MIPI-DSI LCD panel (800x1280) is connected to the DSI port of A64 SoC.
- A mini HDMI port.

Input:
- A touch panel attached to a Goodix GT9271 touch controller.
- Volume keys connected to the LRADC of the A64 SoC.

Camera:
- An OV5640 CMOS camera is at rear, connected to the CSI bus of A64 SoC.
- A GC2145 CMOS camera is at front, shares the same CSI bus with OV5640.

Audio:
- A headphone jack is conencted to the SoC's internal codec.
- A speaker connected is to the Line Out port of SoC's internal codec, via
an amplifier.

Misc:
- Debug UART is muxed with the headphone jack, with the switch next to
the microSD slot.
- A bosch BMA223 accelerometer is connected to the I2C bus of A64 SoC.
- Wi-Fi and Bluetooth are available via a RTL8723CS chip, similar to the
one in Pinebook.

This commit adds a basically usable device tree for it, implementing
most of the features mentioned above. HDMI is not supported now because
bad LCD-HDMI coexistence situation of mainline A64 display driver, the
front camera currently lacks a driver and a facility to share the bus
with the rear one, and the accelerometer currently lacks a DT binding.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

Add the device tree binding for Pine64's PineTab tablet, which uses
Allwinner A64 SoC.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

The Allwinner H6 SPI controller has advanced features over the H3
version, but remains compatible with it.
Document the usual "specific", "fallback" compatible string pair.
Also add the R40 version while at it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

The Pine H64 board comes with SPI flash soldered on the board, connected
to the SPI0 pins (so it can also boot from there).

Add the required SPI flash DT node to describe this.

Unfortunately the SPI CS0 pin collides with the eMMC CMD pin, so we can't
use both eMMC and SPI flash at the same time (the first to claim the pin
would win, the other's probe routine would then fail).

To avoid losing the more useful eMMC device by chance, mark the SPI
device as "disabled" for now. A user or some U-Boot code could fix this
up if needed, for instance if no eMMC has been detected (it's socketed).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

The Allwinner H6 SoC contains two SPI controllers similar to the H3/A64,
but with the added capability of 3-wire and 4-wire operation modes.
For now the driver does not support those, but the SPI registers are
fully backwards-compatible, just adding bits and registers which were
formerly reserved. So we can use the existing driver in "legacy" SPI
modes, for instance to access the SPI NOR flash soldered on the PineH64
board.
We use an H6 specific compatible string in addition to the existing H3
string, so when the driver later gains QSPI support, it should work
automatically without any DT changes.

Tested by accessing the SPI flash on a Pine H64 board (SPI0), also
connecting another SPI flash to the SPI1 header pins.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

Pull more Kbuild updates from Masahiro Yamada:

 - fix randconfig to generate a sane .config

 - rename hostprogs-y / always to hostprogs / always-y, which are more
   natual syntax.

 - optimize scripts/kallsyms

 - fix yes2modconfig and mod2yesconfig

 - make multiple directory targets ('make foo/ bar/') work

* tag 'kbuild-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kbuild: make multiple directory targets work
  kconfig: Invalidate all symbols after changing to y or m.
  kallsyms: fix type of kallsyms_token_table[]
  scripts/kallsyms: change table to store (strcut sym_entry *)
  scripts/kallsyms: rename local variables in read_symbol()
  kbuild: rename hostprogs-y/always to hostprogs/always-y
  kbuild: fix the document to use extra-y for vmlinux.lds
  kconfig: fix broken dependency in randconfig-generated .config

Pull new zonefs file system from Damien Le Moal:
 "Zonefs is a very simple file system exposing each zone of a zoned
  block device as a file.

  Unlike a regular file system with native zoned block device support
  (e.g. f2fs or the on-going btrfs effort), zonefs does not hide the
  sequential write constraint of zoned block devices to the user. As a
  result, zonefs is not a POSIX compliant file system. Its goal is to
  simplify the implementation of zoned block devices support in
  applications by replacing raw block device file accesses with a richer
  file based API, avoiding relying on direct block device file ioctls
  which may be more obscure to developers.

  One example of this approach is the implementation of LSM
  (log-structured merge) tree structures (such as used in RocksDB and
  LevelDB) on zoned block devices by allowing SSTables to be stored in a
  zone file similarly to a regular file system rather than as a range of
  sectors of a zoned device. The introduction of the higher level
  construct "one file is one zone" can help reducing the amount of
  changes needed in the application while at the same time allowing the
  use of zoned block devices with various programming languages other
  than C.

  Zonefs IO management implementation uses the new iomap generic code.
  Zonefs has been successfully tested using a functional test suite
  (available with zonefs userland format tool on github) and a prototype
  implementation of LevelDB on top of zonefs"

* tag 'zonefs-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs:
  zonefs: Add documentation
  fs: New zonefs file system

In order to allow the GICv4 code to link properly on 32bit ARM,
make sure we don't use 64bit divisions when it isn't strictly
necessary.

Fixes: 4e6437f1 ("irqchip/gic-v4.1: Ensure L2 vPE table is allocated at RD level")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull cifs fixes from Steve French:
 "13 cifs/smb3 patches, most from testing at the SMB3 plugfest this week:

   - Important fix for multichannel and for modefromsid mounts.

   - Two reconnect fixes

   - Addition of SMB3 change notify support

   - Backup tools fix

   - A few additional minor debug improvements (tracepoints and
     additional logging found useful during testing this week)"

* tag '5.6-rc-smb3-plugfest-patches' of git://git.samba.org/sfrench/cifs-2.6:
  smb3: Add defines for new information level, FileIdInformation
  smb3: print warning once if posix context returned on open
  smb3: add one more dynamic tracepoint missing from strict fsync path
  cifs: fix mode bits from dir listing when mounted with modefromsid
  cifs: fix channel signing
  cifs: add SMB3 change notification support
  cifs: make multichannel warning more visible
  cifs: fix soft mounts hanging in the reconnect code
  cifs: Add tracepoints for errors on flush or fsync
  cifs: log warning message (once) if out of disk space
  cifs: fail i/o on soft mounts if sessionsetup errors out
  smb3: fix problem with null cifs super block with previous patch
  SMB3: Backup intent flag missing from some more ops

Pull vboxfs from Al Viro:
 "This is the VirtualBox guest shared folder support by Hans de Goede,
  with fixups for fs_parse folded in to avoid bisection hazards from
  those API changes..."

* 'work.vboxsf' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fs: Add VirtualBox guest shared folder (vboxsf) support

Pull x86 fixes from Thomas Gleixner:
 "A set of fixes for X86:

   - Ensure that the PIT is set up when the local APIC is disable or
     configured in legacy mode. This is caused by an ordering issue
     introduced in the recent changes which skip PIT initialization when
     the TSC and APIC frequencies are already known.

   - Handle malformed SRAT tables during early ACPI parsing which caused
     an infinite loop anda boot hang.

   - Fix a long standing race in the affinity setting code which affects
     PCI devices with non-maskable MSI interrupts. The problem is caused
     by the non-atomic writes of the MSI address (destination APIC id)
     and data (vector) fields which the device uses to construct the MSI
     message. The non-atomic writes are mandated by PCI.

     If both fields change and the device raises an interrupt after
     writing address and before writing data, then the MSI block
     constructs a inconsistent message which causes interrupts to be
     lost and subsequent malfunction of the device.

     The fix is to redirect the interrupt to the new vector on the
     current CPU first and then switch it over to the new target CPU.
     This allows to observe an eventually raised interrupt in the
     transitional stage (old CPU, new vector) to be observed in the APIC
     IRR and retriggered on the new target CPU and the new vector.

     The potential spurious interrupts caused by this are harmless and
     can in the worst case expose a buggy driver (all handlers have to
     be able to deal with spurious interrupts as they can and do happen
     for various reasons).

   - Add the missing suspend/resume mechanism for the HYPERV hypercall
     page which prevents resume hibernation on HYPERV guests. This
     change got lost before the merge window.

   - Mask the IOAPIC before disabling the local APIC to prevent
     potentially stale IOAPIC remote IRR bits which cause stale
     interrupt lines after resume"

* tag 'x86-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/apic: Mask IOAPIC entries when disabling the local APIC
  x86/hyperv: Suspend/resume the hypercall page for hibernation
  x86/apic/msi: Plug non-maskable MSI affinity race
  x86/boot: Handle malformed SRAT tables during early ACPI parsing
  x86/timer: Don't skip PIT setup when APIC is disabled or in legacy mode

Pull SMP fixes from Thomas Gleixner:
 "Two fixes for the SMP related functionality:

   - Make the UP version of smp_call_function_single() match SMP
     semantics when called for a not available CPU. Instead of emitting
     a warning and assuming that the function call target is CPU0,
     return a proper error code like the SMP version does.

   - Remove a superfluous check in smp_call_function_many_cond()"

* tag 'smp-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  smp/up: Make smp_call_function_single() match SMP semantics
  smp: Remove superfluous cond_func check in smp_call_function_many_cond()

Pull perf fixes from Thomas Gleixner:
 "A set of fixes and improvements for the perf subsystem:

  Kernel fixes:

   - Install cgroup events to the correct CPU context to prevent a
     potential list double add

   - Prevent an integer underflow in the perf mlock accounting

   - Add a missing prototype for arch_perf_update_userpage()

  Tooling:

   - Add a missing unlock in the error path of maps__insert() in perf
     maps.

   - Fix the build with the latest libbfd

   - Fix the perf parser so it does not delete parse event terms, which
     caused a regression for using perf with the ARM CoreSight as the
     sink configuration was missing due to the deletion.

   - Fix the double free in the perf CPU map merging test case

   - Add the missing ustring support for the perf probe command"

* tag 'perf-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf maps: Add missing unlock to maps__insert() error case
  perf probe: Add ustring support for perf probe command
  perf: Make perf able to build with latest libbfd
  perf test: Fix test case Merge cpu map
  perf parse: Copy string to perf_evsel_config_term
  perf parse: Refactor 'struct perf_evsel_config_term'
  kernel/events: Add a missing prototype for arch_perf_update_userpage()
  perf/cgroups: Install cgroup events to correct cpuctx
  perf/core: Fix mlock accounting in perf_mmap()

Pull timer fixes from Thomas Gleixner:
 "Two small fixes for the time(r) subsystem:

   - Handle a subtle race between the clocksource watchdog and a
     concurrent clocksource watchdog stop/start sequence correctly to
     prevent a timer double add bug.

   - Fix the file path for the core time namespace file"

* tag 'timers-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource: Prevent double add_timer_on() for watchdog_timer
  MAINTAINERS: Correct path to time namespace source file

Pull interrupt fixes from Thomas Gleixner:
 "A set of fixes for the interrupt subsystem:

   - Provision only ACPI enabled redistributors on GICv3

   - Use the proper command colums when building the INVALL command for
     the GICv3-ITS

   - Ensure the allocation of the L2 vPE table for GICv4.1

   - Correct the GICv4.1 VPROBASER programming so it uses the proper
     size

   - A set of small GICv4.1 tidy up patches

   - Configuration cleanup for C-SKY interrupt chip

   - Clarify the function documentation for irq_set_wake() to document
     that the wakeup functionality is orthogonal to the irq
     disable/enable mechanism"

* tag 'irq-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/gic-v3-its: Rename VPENDBASER/VPROPBASER accessors
  irqchip/gic-v3-its: Remove superfluous WARN_ON
  irqchip/gic-v4.1: Drop 'tmp' in inherit_vpe_l1_table_from_rd()
  irqchip/gic-v4.1: Ensure L2 vPE table is allocated at RD level
  irqchip/gic-v4.1: Set vpe_l1_base for all redistributors
  irqchip/gic-v4.1: Fix programming of GICR_VPROPBASER_4_1_SIZE
  genirq: Clarify that irq wake state is orthogonal to enable/disable
  irqchip/gic-v3-its: Reference to its_invall_cmd descriptor when building INVALL
  irqchip: Some Kconfig cleanup for C-SKY
  irqchip/gic-v3: Only provision redistributors that are enabled in ACPI

Pull EFI fix from Thomas Gleixner:
 "A single fix for a EFI boot regression on X86 which was caused by the
  recent rework of the EFI memory map parsing. On systems with invalid
  memmap entries the cleanup function uses an value which cannot be
  relied on in this stage. Use the actual EFI memmap entry instead"

* tag 'efi-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  efi/x86: Fix boot regression on systems with invalid memmap entries

Pull misc SCSI fixes from James Bottomley:
 "Five small patches, all in drivers or doc, which missed the initial
  pull request.

  The qla2xxx and megaraid_sas are actual fixes and the rest are
  spelling and doc changes"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: ufs: fix spelling mistake "initilized" -> "initialized"
  scsi: pm80xx: fix spelling mistake "to" -> "too"
  scsi: MAINTAINERS: ufs: remove pedrom.sousa@synopsys.com
  scsi: megaraid_sas: fixup MSIx interrupt setup during resume
  scsi: qla2xxx: Fix unbound NVME response length

Pull networking fixes from David Miller:

 1) Unbalanced locking in mwifiex_process_country_ie, from Brian Norris.

 2) Fix thermal zone registration in iwlwifi, from Andrei
    Otcheretianski.

 3) Fix double free_irq in sgi ioc3 eth, from Thomas Bogendoerfer.

 4) Use after free in mptcp, from Florian Westphal.

 5) Use after free in wireguard's root_remove_peer_lists, from Eric
    Dumazet.

 6) Properly access packets heads in bonding alb code, from Eric
    Dumazet.

 7) Fix data race in skb_queue_len(), from Qian Cai.

 8) Fix regression in r8169 on some chips, from Heiner Kallweit.

 9) Fix XDP program ref counting in hv_netvsc, from Haiyang Zhang.

10) Certain kinds of set link netlink operations can cause a NULL deref
    in the ipv6 addrconf code. Fix from Eric Dumazet.

11) Don't cancel uninitialized work queue in drop monitor, from Ido
    Schimmel.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
  net: thunderx: use proper interface type for RGMII
  mt76: mt7615: fix max_nss in mt7615_eeprom_parse_hw_cap
  bpf: Improve bucket_log calculation logic
  selftests/bpf: Test freeing sockmap/sockhash with a socket in it
  bpf, sockhash: Synchronize_rcu before free'ing map
  bpf, sockmap: Don't sleep while holding RCU lock on tear-down
  bpftool: Don't crash on missing xlated program instructions
  bpf, sockmap: Check update requirements after locking
  drop_monitor: Do not cancel uninitialized work item
  mlxsw: spectrum_dpipe: Add missing error path
  mlxsw: core: Add validation of hardware device types for MGPIR register
  mlxsw: spectrum_router: Clear offload indication from IPv6 nexthops on abort
  selftests: mlxsw: Add test cases for local table route replacement
  mlxsw: spectrum_router: Prevent incorrect replacement of local table routes
  net: dsa: microchip: enable module autoprobe
  ipv6/addrconf: fix potential NULL deref in inet6_set_link_af()
  dpaa_eth: support all modes with rate adapting PHYs
  net: stmmac: update pci platform data to use phy_interface
  net: stmmac: xgmac: fix missing IFF_MULTICAST checki in dwxgmac2_set_filter
  net: stmmac: fix missing IFF_MULTICAST check in dwmac4_set_filter
  ...

VirtualBox hosts can share folders with guests, this commit adds a
VFS driver implementing the Linux-guest side of this, allowing folders
exported by the host to be mounted under Linux.

This driver depends on the guest <-> host IPC functions exported by
the vboxguest driver.
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull powerpc fixes from Michael Ellerman:

 - Fix an existing bug in our user access handling, exposed by one of
   the bug fixes we merged this cycle.

 - A fix for a boot hang on 32-bit with CONFIG_TRACE_IRQFLAGS and the
   recently added CONFIG_VMAP_STACK.

Thanks to: Christophe Leroy, Guenter Roeck.

* tag 'powerpc-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc: Fix CONFIG_TRACE_IRQFLAGS with CONFIG_VMAP_STACK
  powerpc/futex: Fix incorrect user access blocking

This is a merge error on my part - the driver was merged into mainline
by commit c5951e7c ("Merge tag 'mips_5.6' of git://../mips/linux")
over a week ago, but nobody apparently noticed that it didn't actually
build due to still having a reference to the devm_ioremap_nocache()
function, removed a few days earlier through commit 6a1000bd ("Merge
tag 'ioremap-5.6' of git://../ioremap").

Apparently this didn't get any build testing anywhere.  Not perhaps all
that surprising: it's restricted to 64-bit MIPS only, and only with the
new SGI_MFD_IOC3 support enabled.

I only noticed because the ioremap conflicts in the ARM SoC driver
update made me check there weren't any others hiding, and I found this
one.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ARM SoC late updates from Olof Johansson:
 "This is some material that we picked up into our tree late, or that
  had more complex dependencies on more than one topic branch that makes
  sense to keep separately.

   - TI support for secure accelerators and hwrng on OMAP4/5

   - TI camera changes for dra7 and am437x and SGX improvement due to
     better reset control support on am335x, am437x and dra7

   - Davinci moves to proper clocksource on DM365, and regulator/audio
     improvements for DM365 and DM644x eval boards"

* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (32 commits)
  ARM: dts: omap4-droid4: Enable hdq for droid4 ds250x 1-wire battery nvmem
  ARM: dts: motorola-cpcap-mapphone: Configure calibration interrupt
  ARM: dts: Configure interconnect target module for am437x sgx
  ARM: dts: Configure sgx for dra7
  ARM: dts: Configure rstctrl reset for am335x SGX
  ARM: dts: dra7: Add ti-sysc node for VPE
  ARM: dts: dra7: add vpe clkctrl node
  ARM: dts: am43x-epos-evm: Add VPFE and OV2659 entries
  ARM: dts: am437x-sk-evm: Add VPFE and OV2659 entries
  ARM: dts: am43xx: add support for clkout1 clock
  arm: dts: dra76-evm: Add CAL and OV5640 nodes
  arm: dtsi: dra76x: Add CAL dtsi node
  arm: dts: dra72-evm-common: Add entries for the CSI2 cameras
  ARM: dts: DRA72: Add CAL dtsi node
  ARM: dts: dra7-l4: Add ti-sysc node for CAM
  ARM: OMAP: DRA7xx: Make CAM clock domain SWSUP only
  ARM: dts: dra7: add cam clkctrl node
  ARM: OMAP2+: Drop legacy platform data for omap4 des
  ARM: OMAP2+: Drop legacy platform data for omap4 sham
  ARM: OMAP2+: Drop legacy platform data for omap4 aes
  ...

Pull ARM SoC defconfig updates from Olof Johansson:
 "We keep this in a separate branch to avoid cross-branch conflicts, but
  most of the material here is fairly boring -- some new drivers turned
  on for hardware since they were merged, and some refreshed files due
  to time having moved a lot of entries around"

* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (38 commits)
  ARM: configs: at91: enable MMC_SDHCI_OF_AT91 and MICROCHIP_PIT64B
  arm64: defconfig: Enable Broadcom's GENET Ethernet controller
  ARM: multi_v7_defconfig: Enable devfreq thermal integration
  ARM: exynos_defconfig: Enable devfreq thermal integration
  ARM: multi_v7_defconfig: Enable NFS v4.1 and v4.2
  ARM: exynos_defconfig: Enable NFS v4.1 and v4.2
  arm64: defconfig: Enable Actions Semi specific drivers
  arm64: defconfig: Enable Broadcom's STB PCIe controller
  arm64: defconfig: Enable CONFIG_CLK_IMX8MP by default
  ARM: configs: at91: enable config flags for sam9x60 SoC
  ARM: configs: at91: use savedefconfig
  arm64: defconfig: Enable tegra XUDC support
  ARM: defconfig: gemini: Update defconfig
  arm64: defconfig: enable CONFIG_ARM_QCOM_CPUFREQ_NVMEM
  arm64: defconfig: enable CONFIG_QCOM_CPR
  arm64: defconfig: Enable HFPLL
  arm64: defconfig: Enable CRYPTO_DEV_FSL_CAAM
  ARM: imx_v6_v7_defconfig: Select the TFP410 driver
  ARM: imx_v6_v7_defconfig: Enable NFS_V4_1 and NFS_V4_2 support
  arm64: defconfig: Enable ATH10K_SNOC
  ...

Pull ARM SoC-related driver updates from Olof Johansson:
 "Various driver updates for platforms:

   - Nvidia: Fuse support for Tegra194, continued memory controller
     pieces for Tegra30

   - NXP/FSL: Refactorings of QuickEngine drivers to support
     ARM/ARM64/PPC

   - NXP/FSL: i.MX8MP SoC driver pieces

   - TI Keystone: ring accelerator driver

   - Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.

   - Xilinx ZynqMP: feature checking interface for firmware. Mailbox
     communication for power management

   - Overall support patch set for cpuidle on more complex hierarchies
     (PSCI-based)

  and misc cleanups, refactorings of Marvell, TI, other platforms"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
  drivers: soc: xilinx: Use mailbox IPI callback
  dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
  drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
  MAINTAINERS: Add brcmstb PCIe controller entry
  soc/tegra: fuse: Unmap registers once they are not needed anymore
  soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
  soc/tegra: fuse: Warn if straps are not ready
  soc/tegra: fuse: Cache values of straps and Chip ID registers
  memory: tegra30-emc: Correct error message for timed out auto calibration
  memory: tegra30-emc: Firm up hardware programming sequence
  memory: tegra30-emc: Firm up suspend/resume sequence
  soc/tegra: regulators: Do nothing if voltage is unchanged
  memory: tegra: Correct reset value of xusb_hostr
  soc/tegra: fuse: Add APB DMA dependency for Tegra20
  bus: tegra-aconnect: Remove PM_CLK dependency
  dt-bindings: mediatek: add MT6765 power dt-bindings
  soc: mediatek: cmdq: delete not used define
  memory: tegra: Add support for the Tegra194 memory controller
  memory: tegra: Only include support for enabled SoCs
  memory: tegra: Support DVFS on Tegra186 and later
  ...