- 17 Jun, 2015 24 commits
-
-
Michal Kubeček authored
commit 35f1b4e9 upstream. If adding a nexthop of an IPv6 multipath route fails, comment in ip6_route_multipath() says we are going to delete all nexthops already added. However, current implementation deletes even the routes it hasn't even tried to add yet. For example, running ip route add 1234:5678::/64 \ nexthop via fe80::aa dev dummy1 \ nexthop via fe80::bb dev dummy1 \ nexthop via fe80::cc dev dummy1 twice results in removing all routes first command added. Limit the second (delete) run to nexthops that succeeded in the first (add) run. Fixes: 51ebd318 ("ipv6: add support of equal cost multipath (ECMP)") Signed-off-by:
Michal Kubecek <mkubecek@suse.cz> Acked-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Kamal Mostafa <kamal@canonical.com>
-
Eric W. Biederman authored
commit 381c759d upstream. ip_error does not check if in_dev is NULL before dereferencing it. IThe following sequence of calls is possible: CPU A CPU B ip_rcv_finish ip_route_input_noref() ip_route_input_slow() inetdev_destroy() dst_input() With the result that a network device can be destroyed while processing an input packet. A crash was triggered with only unicast packets in flight, and forwarding enabled on the only network device. The error condition was created by the removal of the network device. As such it is likely the that error code was -EHOSTUNREACH, and the action taken by ip_error (if in_dev had been accessible) would have been to not increment any counters and to have tried and likely failed to send an icmp error as the network device is going away. Therefore handle this weird case by just dropping the packet if !in_dev. It will result in dropping the packet sooner, and will not result in an actual change of behavior. Fixes: 251da413 ("ipv4: Cache ip_error() routes even when not forwarding.") Reported-by:
Vittorio Gambaletta <linuxbugs@vittgam.net> Tested-by:
"Eric W. Biederman" <ebiederm@xmission.com> Acked-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Thadeu Lima de Souza Cascardo authored
commit 47cc84ce upstream. When more than a multicast address is present in a MLDv2 report, all but the first address is ignored, because the code breaks out of the loop if there has not been an error adding that address. This has caused failures when two guests connected through the bridge tried to communicate using IPv6. Neighbor discoveries would not be transmitted to the other guest when both used a link-local address and a static address. This only happens when there is a MLDv2 querier in the network. The fix will only break out of the loop when there is a failure adding a multicast address. The mdb before the patch: dev ovirtmgmt port vnet0 grp ff02::1:ff7d:6603 temp dev ovirtmgmt port vnet1 grp ff02::1:ff7d:6604 temp dev ovirtmgmt port bond0.86 grp ff02::2 temp After the patch: dev ovirtmgmt port vnet0 grp ff02::1:ff7d:6603 temp dev ovirtmgmt port vnet1 grp ff02::1:ff7d:6604 temp dev ovirtmgmt port bond0.86 grp ff02::fb temp dev ovirtmgmt port bond0.86 grp ff02::2 temp dev ovirtmgmt port bond0.86 grp ff02::d temp dev ovirtmgmt port vnet0 grp ff02::1:ff00:76 temp dev ovirtmgmt port bond0.86 grp ff02::16 temp dev ovirtmgmt port vnet1 grp ff02::1:ff00:77 temp dev ovirtmgmt port bond0.86 grp ff02::1:ff00:def temp dev ovirtmgmt port bond0.86 grp ff02::1:ffa1:40bf temp Fixes: 08b202b6 ("bridge br_multicast: IPv6 MLD support.") Reported-by:
Rik Theys <Rik.Theys@esat.kuleuven.be> Signed-off-by:
Thadeu Lima de Souza Cascardo <cascardo@redhat.com> Tested-by:
-
Florian Fainelli authored
commit 7e140696 upstream. RGMII interfaces come in multiple flavors: RGMII with transmit or receive internal delay, no delays at all, or delays in both direction. This change extends the initial check for PHY_INTERFACE_MODE_RGMII to cover all of these variants since EEE should be allowed for any of these modes, since it is a property of the RGMII, hence Gigabit PHY capability more than the RGMII electrical interface and its delays. Fixes: a59a4d19 ("phy: add the EEE support and the way to access to the MMD registers") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Tommi Rantala authored
commit f30bf2a5 upstream. Fix memory leak introduced in commit a0840e2e ("IPVS: netns, ip_vs_ctl local vars moved to ipvs struct."): unreferenced object 0xffff88005785b800 (size 2048): comm "(-localed)", pid 1434, jiffies 4294755650 (age 1421.089s) hex dump (first 32 bytes): bb 89 0b 83 ff ff ff ff b0 78 f0 4e 00 88 ff ff .........x.N.... 04 00 00 00 a4 01 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<ffffffff8262ea8e>] kmemleak_alloc+0x4e/0xb0 [<ffffffff811fba74>] __kmalloc_track_caller+0x244/0x430 [<ffffffff811b88a0>] kmemdup+0x20/0x50 [<ffffffff823276b7>] ip_vs_control_net_init+0x1f7/0x510 [<ffffffff8231d630>] __ip_vs_init+0x100/0x250 [<ffffffff822363a1>] ops_init+0x41/0x190 [<ffffffff82236583>] setup_net+0x93/0x150 [<ffffffff82236cc2>] copy_net_ns+0x82/0x140 [<ffffffff810ab13d>] create_new_namespaces+0xfd/0x190 [<ffffffff810ab49a>] unshare_nsproxy_namespaces+0x5a/0xc0 [<ffffffff810833e3>] SyS_unshare+0x173/0x310 [<ffffffff8265cbd7>] system_call_fastpath+0x12/0x6f [<ffffffffffffffff>] 0xffffffffffffffff Fixes: a0840e2e ("IPVS: netns, ip_vs_ctl local vars moved to ipvs struct.") Signed-off-by:
Tommi Rantala <tt.rantala@gmail.com> Acked-by:
Julian Anastasov <ja@ssi.bg> Signed-off-by:
Simon Horman <horms@verge.net.au> Signed-off-by:
-
Harald Freudenberger authored
commit a1cae34e upstream. Multitheaded tests showed that the icv buffer in the current ghash implementation is not handled correctly. A move of this working ghash buffer value to the descriptor context fixed this. Code is tested and verified with an multithreaded application via af_alg interface. Signed-off-by:
Harald Freudenberger <freude@linux.vnet.ibm.com> Signed-off-by:
Gerald Schaefer <geraldsc@linux.vnet.ibm.com> Reported-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Ilya Dryomov authored
commit b0494532 upstream. This commit does two things. First, if there are any homeless lingering requests, we now request a new osdmap even if the osdmap that is being processed brought no changes, i.e. if a given lingering request turned homeless in one of the previous epochs and remained homeless in the current epoch. Not doing so leaves us with a stale osdmap and as a result we may miss our window for reestablishing the watch and lose notifies. MON=1 OSD=1: # cat linger-needmap.sh #!/bin/bash rbd create --size 1 test DEV=$(rbd map test) ceph osd out 0 rbd map dne/dne # obtain a new osdmap as a side effect (!) sleep 1 ceph osd in 0 rbd resize --size 2 test # rbd info test | grep size -> 2M # blockdev --getsize $DEV -> 1M N.B.: Not obtaining a new osdmap in between "osd out" and "osd in" above is enough to make it miss that resize notify, but that is a bug^Wlimitation of ceph watch/notify v1. Second, homeless lingering requests are now kicked just like those lingering requests whose mapping has changed. This is mainly to recognize that a homeless lingering request makes no sense and to preserve the invariant that a registered lingering request is not sitting on any of r_req_lru_item lists. This spares us a WARN_ON, which commit ba9d114e ("libceph: clear r_req_lru_item in __unregister_linger_request()") tried to fix the _wrong_ way. Signed-off-by:
Ilya Dryomov <idryomov@gmail.com> Reviewed-by:
Sage Weil <sage@redhat.com> Signed-off-by:
-
Mark Hounschell authored
commit 74856fbf upstream. 256 bytes per sector support has been broken since 2.6.X, and no-one stepped up to fix this. So disable support for it. Signed-off-by:
Mark Hounschell <dmarkh@cfl.rr.com> Signed-off-by:
Hannes Reinecke <hare@suse.de> Signed-off-by:
James Bottomley <JBottomley@Odin.com> Signed-off-by:
-
Ludovic Desroches authored
commit 60c8f783 upstream. clkdiv is declared as an u32 but it can be set to a negative value causing a huge divisor value. Change its type to int to avoid this case. Signed-off-by:
Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
David Henningsson authored
commit 6ffc0898 upstream. This patch adds support for Conexant HD Audio codecs CX20721, CX20722, CX20723 and CX20724. BugLink: https://bugs.launchpad.net/bugs/1454656Signed-off-by:
David Henningsson <david.henningsson@canonical.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Anton Blanchard authored
commit 5e95235c upstream. Recent toolchains force the TOC to be 256 byte aligned. We need to enforce this alignment in our linker script, otherwise pointers to our TOC variables (__toc_start, __prom_init_toc_start) could be incorrect. If they are bad, we die a few hundred instructions into boot. Signed-off-by:
Anton Blanchard <anton@samba.org> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Benjamin Tissoires authored
commit 3c0213d1 upstream. When the v3 hardware sees more than one finger, it uses the semi-mt protocol to report the touches. However, it currently works when num_fingers is 0, 1 or 2, but when it is 3 and above, it sends only 1 finger as if num_fingers was 1. This confuses userspace which knows how to deal with extra fingers when all the slots are used, but not when some are missing. Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=90101Signed-off-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Zidan Wang authored
commit 17fc2e0a upstream. According to the RM of wm8958, BCLK DIV 348 doesn't exist, correct it to 384. Signed-off-by:
Zidan Wang <zidan.wang@freescale.com> Acked-by:
Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Zidan Wang authored
commit 85e36a1f upstream. It should be "RINPUT3" instead of "LINPUT3" route to "Right Input Mixer". Signed-off-by:
-
K. Y. Srinivasan authored
commit dc45708c upstream. Set the SRB flags correctly when there is no data transfer. Without this change some IHV drivers will fail valid commands such as TEST_UNIT_READY. Signed-off-by:
K. Y. Srinivasan <kys@microsoft.com> Reviewed-by:
Long Li <longli@microsoft.com> Signed-off-by:
-
Xiao Guangrong authored
commit 0be0226f upstream. KVM may turn a user page to a kernel page when kernel writes a readonly user page if CR0.WP = 1. This shadow page entry will be reused after SMAP is enabled so that kernel is allowed to access this user page Fix it by setting SMAP && !CR0.WP into shadow page's role and reset mmu once CR4.SMAP is updated Signed-off-by:
Xiao Guangrong <guangrong.xiao@linux.intel.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> [ kamal: backport to 3.13-stable: context ] Signed-off-by:
-
Paolo Bonzini authored
commit 89876115 upstream. smep_andnot_wp is initialized in kvm_init_shadow_mmu and shadow pages should not be reused for different values of it. Thus, it has to be added to the mask in kvm_mmu_pte_write. Reviewed-by:
-
Xiao Guangrong authored
commit 7cbeed9b upstream. Current permission check assumes that RSVD bit in PFEC is always zero, however, it is not true since MMIO #PF will use it to quickly identify MMIO access Fix it by clearing the bit if walking guest page table is needed Signed-off-by:
-
Janusz Dziedzic authored
commit 47b4e1fc upstream. Remove checking tailroom when adding IV as it uses only headroom, and move the check to the ICV generation that actually needs the tailroom. In other case I hit such warning and datapath don't work, when testing: - IBSS + WEP - ath9k with hw crypt enabled - IPv6 data (ping6) WARNING: CPU: 3 PID: 13301 at net/mac80211/wep.c:102 ieee80211_wep_add_iv+0x129/0x190 [mac80211]() [...] Call Trace: [<ffffffff817bf491>] dump_stack+0x45/0x57 [<ffffffff8107746a>] warn_slowpath_common+0x8a/0xc0 [<ffffffff8107755a>] warn_slowpath_null+0x1a/0x20 [<ffffffffc09ae109>] ieee80211_wep_add_iv+0x129/0x190 [mac80211] [<ffffffffc09ae7ab>] ieee80211_crypto_wep_encrypt+0x6b/0xd0 [mac80211] [<ffffffffc09d3fb1>] invoke_tx_handlers+0xc51/0xf30 [mac80211] [...] Signed-off-by:
Janusz Dziedzic <janusz.dziedzic@tieto.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Vasily Khoruzhick authored
commit 810e4425 upstream. set_dai_fmt_both() callback is called from snd_soc_runtime_set_dai_fmt() which is called from snd_soc_register_card(), but at this time codec is not powered on yet. Replace direct i2c write with regcache write. Fixes: 5f0acedd (ASoC: rx1950_uda1380: Use static DAI format setup) Fixes: 5cc10b9b (ASoC: h1940_uda1380: Use static DAI format setup) Signed-off-by:
Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by:
-
Axel Lin authored
commit 545774bd upstream. mc13xxx_reg_rmw() won't change any bit if passing 0 to the mask field. Pass AUDIO_SSI_SEL instead of 0 for the mask field to set AUDIO_SSI_SEL bit. Signed-off-by:
Axel Lin <axel.lin@ingics.com> Signed-off-by:
-
Takashi Iwai authored
commit 88776f36 upstream. Fujitsu Lifebook E752 laptop needs a similar quirk done for Lifebook T731. Otherwise the headphone is always muted. Reported-and-tested-by:
Christian Weber <we_chris@hotmail.com> Signed-off-by:
-
Nick Meier authored
commit 5ef5b692 upstream. HV_CRASH_CTL_CRASH_NOTIFY is a 64 bit number. Depending on the usage context, the value may be truncated. This patch is in response from the following email from Wu Fengguang <fengguang.wu@intel.com>: From: Wu Fengguang <fengguang.wu@intel.com> Subject: [char-misc:char-misc-testing 25/45] drivers/hv/vmbus_drv.c:67:9: sparse: constant 0x8000000000000000 is so big it is unsigned long tree: git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc.git char-misc-testing head: b3de8e37 commit: 96c1d058 [25/45] Drivers: hv: vmbus: Add support for VMBus panic notifier handler reproduce: # apt-get install sparse git checkout 96c1d058 make ARCH=x86_64 allmodconfig make C=1 CF=-D__CHECK_ENDIAN__ sparse warnings: (new ones prefixed by >>) drivers/hv/vmbus_drv.c:67:9: sparse: constant 0x8000000000000000 is so big it is unsigned long ... Signed-off-by:
Nick Meier <nmeier@microsoft.com> Reported-by:
Wu Fengguang <fengguang.wu@intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Nick Meier authored
commit 96c1d058 upstream. BugLink: http://bugs.launchpad.net/bugs/1463584 Hyper-V allows a guest to notify the Hyper-V host that a panic condition occured. This notification can include up to five 64 bit values. These 64 bit values are written into crash MSRs. Once the data has been written into the crash MSRs, the host is then notified by writing into a Crash Control MSR. On the Hyper-V host, the panic notification data is captured in the Windows Event log as a 18590 event. Crash MSRs are defined in appendix H of the Hypervisor Top Level Functional Specification. At the time of this patch, v4.0 is the current functional spec. The URL for the v4.0 document is: http://download.microsoft.com/download/A/B/4/AB43A34E-BDD0-4FA6-BDEF-79EEF16E880B/Hypervisor Top Level Functional Specification v4.0.docx Signed-off-by:
Joseph Salisbury <joseph.salisbury@canonical.com> Signed-off-by:
-
- 16 Jun, 2015 16 commits
-
-
Nicolas Schichan authored
ARM: net: delegate filter to kernel interpreter when imm_offset() return value can't fit into 12bits. commit 0b59d880 upstream. The ARM JIT code emits "ldr rX, [pc, #offset]" to access the literal pool. #offset maximum value is 4095 and if the generated code is too large, the #offset value can overflow and not point to the expected slot in the literal pool. Additionally, when overflow occurs, bits of the overflow can end up changing the destination register of the ldr instruction. Fix that by detecting the overflow in imm_offset() and setting a flag that is checked for each BPF instructions converted in build_body(). As of now it can only be detected in the second pass. As a result the second build_body() call can now fail, so add the corresponding cleanup code in that case. Using multiple literal pools in the JITed code is going to require lots of intrusive changes to the JIT code (which would better be done as a feature instead of fix), just delegating to the kernel BPF interpreter in that case is a more straight forward, minimal fix and easy to backport. Fixes: ddecdfce ("ARM: 7259/3: net: JIT compiler for packet filters") Signed-off-by:
Nicolas Schichan <nschichan@freebox.fr> Acked-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
-
Toshiaki Makita authored
commit 2439fc4d upstream. adapter->tx_ring is set to NULL where rx_ring should be. Fixes: 5536d210 ("igb: Combine q_vector and ring allocation into a single function") Signed-off-by:
Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
-
Pelle Nilsson authored
commit 7d0ec8b6 upstream. Some controller drivers have no need of this callback (spi-altera even causes a NULL pointer dereference because it doesn't register the callback, falsely assuming that it is already optional). Fixes: 30af9b55 ("spi/bitbang: Drop empty setup() functions") Signed-off-by:
Pelle Nilsson <per.nilsson@xelmo.com> Reviewed-by:
Ezequiel Garcia <ezequiel.garcia@vanguardiasur.com.ar> Signed-off-by:
-
Mel Gorman authored
commit b0dc2b9b upstream. NUMA balancing is meant to be disabled by default on UMA machines but the check is using nr_node_ids (highest node) instead of num_online_nodes (online nodes). The consequences are that a UMA machine with a node ID of 1 or higher will enable NUMA balancing. This will incur useless overhead due to minor faults with the impact depending on the workload. These are the impact on the stats when running a kernel build on a single node machine whose node ID happened to be 1: vanilla patched NUMA base PTE updates 5113158 0 NUMA huge PMD updates 643 0 NUMA page range updates 5442374 0 NUMA hint faults 2109622 0 NUMA hint local faults 2109622 0 NUMA hint local percent 100 100 NUMA pages migrated 0 0 Signed-off-by:
Mel Gorman <mgorman@suse.de> Reviewed-by:
Rik van Riel <riel@redhat.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Darrick J. Wong authored
commit e531d0bc upstream. The journal revoke block recovery code does not check r_count for sanity, which means that an evil value of r_count could result in the kernel reading off the end of the revoke table and into whatever garbage lies beyond. This could crash the kernel, so fix that. However, in testing this fix, I discovered that the code to write out the revoke tables also was not correctly checking to see if the block was full -- the current offset check is fine so long as the revoke table space size is a multiple of the record size, but this is not true when either journal_csum_v[23] are set. Signed-off-by:
Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Reviewed-by:
Jan Kara <jack@suse.cz> Signed-off-by:
-
Eryu Guan authored
commit 2f974865 upstream. The following commit introduced a bug when checking for zero length extent 5946d089 ext4: check for overlapping extents in ext4_valid_extent_entries() Zero length extent could pass the check if lblock is zero. Adding the explicit check for zero length back. Signed-off-by:
Eryu Guan <guaneryu@gmail.com> Signed-off-by:
-
Lukas Czerner authored
commit 9d506594 upstream. Currently when journal restart fails, we'll have the h_transaction of the handle set to NULL to indicate that the handle has been effectively aborted. We handle this situation quietly in the jbd2_journal_stop() and just free the handle and exit because everything else has been done before we attempted (and failed) to restart the journal. Unfortunately there are a number of problems with that approach introduced with commit 41a5b913 "jbd2: invalidate handle if jbd2_journal_restart() fails" First of all in ext4 jbd2_journal_stop() will be called through __ext4_journal_stop() where we would try to get a hold of the superblock by dereferencing h_transaction which in this case would lead to NULL pointer dereference and crash. In addition we're going to free the handle regardless of the refcount which is bad as well, because others up the call chain will still reference the handle so we might potentially reference already freed memory. Moreover it's expected that we'll get aborted handle as well as detached handle in some of the journalling function as the error propagates up the stack, so it's unnecessary to call WARN_ON every time we get detached handle. And finally we might leak some memory by forgetting to free reserved handle in jbd2_journal_stop() in the case where handle was detached from the transaction (h_transaction is NULL). Fix the NULL pointer dereference in __ext4_journal_stop() by just calling jbd2_journal_stop() quietly as suggested by Jan Kara. Also fix the potential memory leak in jbd2_journal_stop() and use proper handle refcounting before we attempt to free it to avoid use-after-free issues. And finally remove all WARN_ON(!transaction) from the code so that we do not get random traces when something goes wrong because when journal restart fails we will get to some of those functions. Signed-off-by:
Lukas Czerner <lczerner@redhat.com> Signed-off-by:
-
Jean Delvare authored
commit 5c1ac56b upstream. In function dmi_present(), dmi_walk_early() calls dmi_table(), which calls dmi_decode(), which ultimately calls dmi_save_uuid(). This last function makes a decision based on the value of global variable dmi_ver. The problem is that this variable is set right _after_ dmi_walk_early() returns. So dmi_save_uuid() always sees dmi_ver == 0 regardless of the actual version implemented. This causes /sys/class/dmi/id/product_uuid to always use the old ordering even on systems implementing DMI/SMBIOS 2.6 or later, which should use the new ordering. This is broken since kernel v3.8 for legacy DMI implementations and since kernel v3.10 for SMBIOS 2 implementations. SMBIOS 3 implementations with the 64-bit entry point are not affected. The first breakage does not matter much as in practice legacy DMI implementations are always for versions older than 2.6, which is when the UUID ordering changed. The second breakage is more problematic as it affects the vast majority of x86 systems manufactured since 2009. Signed-off-by:
Jean Delvare <jdelvare@suse.de> Fixes: 9f9c9cbb ("drivers/firmware/dmi_scan.c: fetch dmi version from SMBIOS if it exists") Fixes: 79bae42d ("dmi_scan: refactor dmi_scan_machine(), {smbios,dmi}_present()") Acked-by:
Zhenzhong Duan <zhenzhong.duan@oracle.com> Cc: Ben Hutchings <ben@decadent.org.uk> Cc: Artem Savkov <artem.savkov@gmail.com> Cc: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Cc: Matt Fleming <matt.fleming@intel.com> Signed-off-by:
-
Alex Deucher authored
commit fcf3b542 upstream. Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Christian König authored
commit 607d4806 upstream. The mapping range is inclusive between starting and ending addresses. Signed-off-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
-
Nicolas Schichan authored
commit 19fc99d0 upstream. In that case, emit_udiv() will be called with rn == ARM_R0 (r_scratch) and loading rm first into ARM_R0 will result in jit_udiv() function being called the same dividend and divisor. Fix that by loading rn first into ARM_R1 and then rm into ARM_R0. Signed-off-by:
Mircea Gherzan <mgherzan@gmail.com> Signed-off-by:
-
Hans de Goede authored
commit 17211509 upstream. Without this flag some versions of these enclosures do not work. Reported-and-tested-by:
Christian Schaller <cschalle@redhat.com> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Joe Lawrence authored
commit 948fa135 upstream. If the xHCI host controller has died (ie, device removed) or suffered other serious fatal error (STS_FATAL), then xhci_irq should handle this condition with IRQ_HANDLED instead of -ESHUTDOWN. Signed-off-by:
Joe Lawrence <joe.lawrence@stratus.com> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Mathias Nyman authored
commit 18cc2f4c upstream. Our event ring consists of only one segment, and we risk filling the event ring in case we get isoc transfers with short intervals such as webcams that fill a TD every microframe (125us) With 64 TRB segment size one usb camera could fill the event ring in 8ms. A setup with several cameras and other devices can fill up the event ring as it is shared between all devices. This has occurred when uvcvideo queues 5 * 32TD URBs which then get cancelled when the video mode changes. The cancelled URBs are returned in the xhci interrupt context and blocks the interrupt handler from handling the new events. A full event ring will block xhci from scheduling traffic and affect all devices conneted to the xhci, will see errors such as Missed Service Intervals for isoc devices, and and Split transaction errors for LS/FS interrupt devices. Increasing the TRB_PER_SEGMENT will also increase the default endpoint ring size, which is welcome as for most isoc transfer we had to dynamically expand the endpoint ring anyway to be able to queue the 5 * 32TDs uvcvideo queues. The default size used to be 64 TRBs per segment Signed-off-by:
-
Mathias Nyman authored
commit d104d015 upstream. Isoc TDs usually consist of one TRB, sometimes two. When all goes well we receive only one success event for a TD, and move the dequeue pointer to the next TD. This fails if the TD consists of two TRBs and we get a transfer error on the first TRB, we will then see two events for that TD. Fix this by making sure the event we get is for the last TRB in that TD before moving the dequeue pointer to the next TD. This will resolve some of the uvc and dvb issues with the "ERROR Transfer event TRB DMA ptr not part of current TD" error message Signed-off-by:
-
NeilBrown authored
commit 6e9eac2d upstream. If any memory allocation in resize_stripes fails we will return -ENOMEM, but in some cases we update conf->pool_size anyway. This means that if we try again, the allocations will be assumed to be larger than they are, and badness results. So only update pool_size if there is no error. This bug was introduced in 2.6.17 and the patch is suitable for -stable. Fixes: ad01c9e3 ("[PATCH] md: Allow stripes to be expanded in preparation for expanding an array") Signed-off-by:
NeilBrown <neilb@suse.de> Signed-off-by:
-
