- 05 Feb, 2013 40 commits
-
-
Laurent Pinchart authored
The struct v4l2_capability card field stores the device name. That name can be hardcoded in drivers, or be retrieved directly from the device. The later is very common with USB devices. As several devices already report names that include non-ASCII characters, update the field description to use UTF-8. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Nickolai Zeldovich authored
The idx values passed to cx18_i2c_register() and ivtv_i2c_register() by cx18_init_subdevs() and ivtv_load_and_init_modules() respectively are always in-range, based on how the hw_all bitmask is populated. Previously, the checks were already ineffective because arrays were being dereferenced using the index before the check. Acked-by:
Andy Walls <awalls@md.metrocast.net> Signed-off-by:
Nickolai Zeldovich <nickolai@csail.mit.edu> Signed-off-by:
-
Nickolai Zeldovich authored
Fix bug introduced in 7757ddda, where instead of bit-negating the bitmask, the bit position was bit-negated instead. Signed-off-by:
-
Sean Young authored
On cold boot the device does not initialize until the first packet is received, and that packet is not processed. Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
-
Sean Young authored
Signed-off-by:
-
Sean Young authored
A sample resolution of 2us generates more than 300 interrupts per key and this resolution is not needed unless carrier reports are enabled. Revert to a resolution of 10us unless carrier reports are needed. This generates up to a fifth of the interrupts. Signed-off-by:
David Härdeman <david@hardeman.nu> Signed-off-by:
-
Lad, Prabhakar authored
Without this patch the adv7343 encoder was being set to default configuration which caused display not to work on this board. This patch passes the necessary platform data required for adv7343 encoder to work on da850 evm. Signed-off-by:
Lad, Prabhakar <prabhakar.lad@ti.com> Acked-by:
Sekhar Nori <nsekhar@ti.com> Signed-off-by:
-
Lad, Prabhakar authored
The current code was implemented with some default configurations, this default configuration works on board and doesn't work on other. This patch accepts the configuration through platform data and configures the encoder depending on the data passed. Signed-off-by:
-
Hans Verkuil authored
Two fixes: - the priv field wasn't set to 0. - only V4L2_FIELD_INTERLACED is supported. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
- add device_caps support - fix bus_info - fix numerous tuner-related problems due to incorrect tests and setting v4l2_tuner fields to wrong values. - remove (audio) input support from the radio: it doesn't belong there. This also fixed a nasty issue where opening the radio would set dev->input to 5 for no good reason. This was never set back to a valid TV input after closing the radio device, thus leaving it at 5 which is out of bounds of the vinput card array. Signed-off-by:
-
Hans Verkuil authored
Convert the meye driver to the control framework. Some private controls have been replaced with standardized controls (SHARPNESS and JPEGQUAL). The AGC control looks like it can be replaced by the AUTOGAIN control, but it isn't a boolean so I do not know how to interpret it. The FRAMERATE control looks like it can be replaced by S_PARM, but again, without knowing how to interpret it I decided to leave it alone. Signed-off-by:
-
Hans Verkuil authored
If you only poll for events, then vb2_poll will return POLLPRI | POLLERR if no streaming is in progress. That's not right, it's perfectly valid to poll just for events. Cc: Pawel Osciak <pawel@osciak.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by:
-
Hans Verkuil authored
These are already done elsewhere. Signed-off-by:
-
Hans Verkuil authored
I know, nobody really cares about this black-and-white webcam anymore, but it was fun to do. Tested with an actual webcam. Signed-off-by:
-
Hans Verkuil authored
Fix a v4l2-compliance problem: the priv field of v4l2_pix_format must be cleared by drivers. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
- instead of a mute module option, use audmode as per the spec. - clamp the frequency before setting it. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Such ioctls are not valid for radio devices. Signed-off-by:
-
Hans Verkuil authored
Don't set version (done by the v4l2 core), fill in bus_info, set correct driver name and add device_caps support. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
The inputmask for the tea6420 wasn't set and the wrong mute register value was used. Signed-off-by:
-
Hans Verkuil authored
The balance control did not do what it is supposed to do due to wrong calculations. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by:
-
Hans Verkuil authored
When the control IDs were split off from videodev2.h to v4l2-controls.h these new Digital Video controls were forgotten (the two patches may have crossed one another). Move these controls to their proper place in v4l2-controls.h. Signed-off-by:
-
Sylwester Nawrocki authored
Newer Exynos4 SoC are equipped with a local camera ISP that controls external raw image sensor directly. Such sensors can be connected through FIMC-LITEn (and MIPI-CSISn) IPs to the ISP, which then feeds image data to the FIMCn IP. Thus there can be two busses associated with an image source (sensor). Rename struct s5p_fimc_isp_info describing external image sensor (video decoder) to struct fimc_source_info to avoid confusion. bus_type is split into fimc_bus_type and sensor_bus_type. The bus type enumeration is extended to include both FIMC Writeback input types. The bus_type enumeration and the data structure name in the board files are modified according to the above changes. Signed-off-by:
Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by:
Kyungmin Park <kyungmin.park@samsung.com> Acked-by:
Kukjin Kim <kgene.kim@samsung.com> Signed-off-by:
-
Andrzej Hajda authored
Signed-off-by:
Andrzej Hajda <a.hajda@samsung.com> Signed-off-by:
-
Sachin Kamat authored
devm_regulator_bulk_get saves some cleanup and exit code. Signed-off-by:
Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by:
-
Sylwester Nawrocki authored
Add clk_prepare(), clk_unprepare() calls for the sclk_cam clocks to ensure the driver works on platforms with the common clocks API enabled. Signed-off-by:
-
Sylwester Nawrocki authored
The V4L2_SEL_TGT_CROP_BOUNDS, V4L2_SEL_TGT_COMPOSE_BOUNDS selection targets are not supposed to be handled in the set_selection ioctl. Remove the code that doesn't do anything sensible now and make sure ctx->state is modified with the spinlock held. Signed-off-by:
-
Sylwester Nawrocki authored
Make sure a valid image format is initially set on both the CAPTURE and the OUTPUT buffer queue. Signed-off-by:
-
Sylwester Nawrocki authored
With presence of some faults, e.g. caused by wrong platform data or the device tree structure the IDX_SENSOR entry in the array may be NULL, so make sure it is not dereferenced then. Signed-off-by:
-
Sachin Kamat authored
Fixes the following sparse warnings: drivers/media/i2c/s5c73m3/s5c73m3-core.c:42:5: warning: symbol 'boot_from_rom' was not declared. Should it be static? drivers/media/i2c/s5c73m3/s5c73m3-core.c:45:5: warning: symbol 'update_fw' was not declared. Should it be static? drivers/media/i2c/s5c73m3/s5c73m3-core.c:298:5: warning: symbol 's5c73m3_isp_comm_result' was not declared. Should it be static? Signed-off-by:
-
Sylwester Nawrocki authored
clk_set_rate(), clk_enable() functions can fail, so check the return values to avoid surprises. While at it use ERR_PTR() value to indicate an invalid clock. Signed-off-by:
-
Sylwester Nawrocki authored
clk_set_rate(), clk_enable() functions can fail, so check the return values to avoid surprises. While at it use ERR_PTR() value to indicate an invalid clock. Signed-off-by:
-
