Enable deflate/lz77_zstd algorithm for uacce device on Kunpeng930.
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

If the hardware reports the 'CQ' overflow or 'CQE' error by the abnormal
interrupt, disable the queue and stop tasks send to hardware.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

If the hardware reports the event queue overflow by the abnormal interrupt,
the driver needs to reset the function and re-enable the event queue
interrupt and abnormal interrupt.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The abnormal interrupt method needs to be changed, and the changed method
needs to be locked in order to maintain atomicity. Therefore,
replace request_irq() with request_threaded_irq().
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

After processing an interrupt event and the interrupt function is
enabled by writing the QM_DOORBELL_CMD_AEQ register, the hardware
may generate new interrupt events due to processing other user's task
when the subsequent interrupt events have not been processed. The new
interrupt event will disrupt the current normal processing flow and
cause other problems.

Therefore, the operation of writing the QM_DOORBELL_CMD_AEQ doorbell
register needs to be placed after all interrupt events processing
are completed.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

This patch does not change any code, just code movement. Preparing for
next patch.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The internal memory of the device needs to be reset only when
the device is globally initialized. Other scenarios, such as
function reset, do not need to perform reset.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

When remove the driver and executing the task occur at the same time,
the following deadlock will be triggered:

Chain exists of:
    sva_lock --> uacce_mutex --> &qm->qps_lock
    Possible unsafe locking scenario:
		CPU0                    CPU1
		----                    ----
	lock(&qm->qps_lock);
					lock(uacce_mutex);
					lock(&qm->qps_lock);
	lock(sva_lock);

And the lock 'qps_lock' is used to protect qp. Therefore, it's reasonable
cycle is to continue until the qp memory is released. So move the release
lock infront of 'uacce_remove'.
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

For Kunpeng 920, the bit 0 of register 'HZIP_SGL_RUSER_32_63' stand for
whether the ssid is valid. So this bit should be set as valid for sva mode.
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

hpre_curve25519_src_init() allocates memory for 'ptr' before calling
memcmp(). If memcmp() returns 0, the function will return '-EINVAL'
without freeing memory.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

When kernel.h is used in the headers it adds a lot into dependency hell,
especially when there are circular dependencies are involved.

Replace kernel.h inclusion with the list of what is really being used.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Use 2-factor multiplication argument form kcalloc() instead
of kzalloc().

Link: https://github.com/KSPP/linux/issues/162Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Use 2-factor multiplication argument form kcalloc() instead
of kzalloc().

Link: https://github.com/KSPP/linux/issues/162Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Add new module parameter to allow users to use SEV_INIT_EX instead of
SEV_INIT. This helps users who lock their SPI bus to use the PSP for SEV
functionality. The 'init_ex_path' parameter defaults to NULL which means
the kernel will use SEV_INIT, if a path is specified SEV_INIT_EX will be
used with the data found at the path. On certain PSP commands this
file is written to as the PSP updates the NV memory region. Depending on
file system initialization this file open may fail during module init
but the CCP driver for SEV already has sufficient retries for platform
initialization. During normal operation of PSP system and SEV commands
if the PSP has not been initialized it is at run time. If the file at
'init_ex_path' does not exist the PSP will not be initialized. The user
must create the file prior to use with 32Kb of 0xFFs per spec.
Signed-off-by: David Rientjes <rientjes@google.com>
Co-developed-by: Peter Gonda <pgonda@google.com>
Signed-off-by: Peter Gonda <pgonda@google.com>
Reviewed-by: Marc Orr <marcorr@google.com>
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Brijesh Singh <brijesh.singh@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Marc Orr <marcorr@google.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Rientjes <rientjes@google.com>
Cc: John Allen <john.allen@amd.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Add psp_init_on_probe module parameter that allows for skipping the
PSP's SEV platform initialization during module init. User may decouple
module init from PSP init due to use of the INIT_EX support in upcoming
patch which allows for users to save PSP's internal state to file. The
file may be unavailable at module init.

Also moves the PSP ABI version log message to after successful PSP init
instead of module init in case this new parameter is used.
Signed-off-by: Peter Gonda <pgonda@google.com>
Acked-by: Brijesh Singh <brijesh.singh@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Marc Orr <marcorr@google.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Rientjes <rientjes@google.com>
Cc: John Allen <john.allen@amd.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Create a helper function sev_fw_alloc() which can be used to allocate
aligned memory regions for use by the PSP firmware. Currently only used
for the SEV-ES TMR region but will be used for the SEV_INIT_EX NV memory
region.
Signed-off-by: Peter Gonda <pgonda@google.com>
Reviewed-by: Marc Orr <marcorr@google.com>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Brijesh Singh <brijesh.singh@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Marc Orr <marcorr@google.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Rientjes <rientjes@google.com>
Cc: John Allen <john.allen@amd.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Move the data corrupted retry of SEV_INIT into the
__sev_platform_init_locked() function. This is for upcoming INIT_EX
support as well as helping direct callers of
__sev_platform_init_locked() which currently do not support the
retry.
Signed-off-by: Peter Gonda <pgonda@google.com>
Reviewed-by: Marc Orr <marcorr@google.com>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Acked-by: Brijesh Singh <brijesh.singh@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Marc Orr <marcorr@google.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Rientjes <rientjes@google.com>
Cc: John Allen <john.allen@amd.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Currently only the firmware error code is printed. This is incomplete
and also incorrect as error cases exists where the firmware is never
called and therefore does not set an error code.
Signed-off-by: Peter Gonda <pgonda@google.com>
Reviewed-by: Marc Orr <marcorr@google.com>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Acked-by: Brijesh Singh <brijesh.singh@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Marc Orr <marcorr@google.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Rientjes <rientjes@google.com>
Cc: John Allen <john.allen@amd.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The variable nbytes is being assigned a value that is never read, it is
being re-assigned in the following statement. The assignment is redundant
and can be removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

When hisi_qm_resume() returns 0, it indicates that the device has started
successfully.  If the device fails to start, hisi_qm_resume() needs to
return the actual error code to the caller instead of 0.

Fixes: d7ea5339 ("crypto: hisilicon - add runtime PM ops")
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Added devlink parameters to create and delete custom CPT engine groups.

Example:
devlink dev param set pci/0002:20:00.0 name egrp_create value \
                "se:32;se.out" cmode runtime
devlink dev param set pci/0002:20:00.0 name egrp_delete value \
                "egrp:1" cmode runtime
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Shijith Thotton <sthotton@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Octeon TX2 CPT has three type of engines to handle symmetric, asymmetric
and ipsec specific workload. For better utilization, these engines can
be grouped to custom groups at runtime.

This patch adds APIs to create and delete custom CPT engine groups.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Shijith Thotton <sthotton@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

We should not call pm_runtime_resume_and_get where the reference
count is expected to be incremented unconditionally.  This patch
reverts these calls to the original unconditional get_sync call.
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: 747bf30f ("crypto: stm32/cryp - Fix PM reference leak...")
Fixes: 1cb3ad70 ("crypto: stm32/hash - Fix PM reference leak...")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The jitterentropy collection loop in jent_gen_entropy() can in principle
run indefinitely without making any progress if it only receives stuck
measurements as determined by jent_stuck(). After 31 consecutive stuck
samples, the Repetition Count Test (RCT) would fail anyway and the
jitterentropy RNG instances moved into ->health_failure == 1 state.
jent_gen_entropy()'s caller, jent_read_entropy() would then check for
this ->health_failure condition and return an error if found set. It
follows that there's absolutely no point in continuing the collection loop
in jent_gen_entropy() once the RCT has failed.

Make the jitterentropy collection loop more robust by terminating it upon
jent_health_failure() so that it won't continue to run indefinitely without
making any progress.
Signed-off-by: Nicolai Stange <nstange@suse.de>
Reviewed-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The jitterentropy's Repetition Count Test (RCT) as well as the Adaptive
Proportion Test (APT) are run unconditionally on any collected samples.
However, their result, i.e. ->health_failure, will only get checked if
fips_enabled is set, c.f. the jent_health_failure() wrapper.

I would argue that a RCT or APT failure indicates that something's
seriously off and that this should always be reported as an error,
independently of whether FIPS mode is enabled or not: it should be up to
callers whether or not and how to handle jitterentropy failures.

Make jent_health_failure() to unconditionally return ->health_failure,
independent of whether fips_enabled is set.

Note that fips_enabled isn't accessed from the jitterentropy code anymore
now. Remove the linux/fips.h include as well as the jent_fips_enabled()
wrapper.
Signed-off-by: Nicolai Stange <nstange@suse.de>
Reviewed-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

A subsequent patch will make the jitterentropy RNG to unconditionally
report health test errors back to callers, independent of whether
fips_enabled is set or not. The DRBG needs access to a functional
jitterentropy instance only in FIPS mode (because it's the only SP800-90B
compliant entropy source as it currently stands). Thus, it is perfectly
fine for the DRBGs to obtain entropy from the jitterentropy source only
on a best effort basis if fips_enabled is off.

Make the DRBGs to ignore jitterentropy failures if fips_enabled is not set.
Signed-off-by: Nicolai Stange <nstange@suse.de>
Reviewed-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The CRYP IP checks the written key depending of the configuration, it's
safer to write the whole configuration to hardware then the key to avoid
unexpected key rejection.
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Extra crypto manager auto test were crashing or failling due
to 2 reasons:
- block in a dead loop (dues to issues in cipher end process management)
- crash due to read/write unmapped memory (this crash was also reported
when using openssl afalg engine)

Rework interrupt management, interrupts are masked as soon as they are
no more used: if input buffer is fully consumed, "Input FIFO not full"
interrupt is masked and if output buffer is full, "Output FIFO not
empty" interrupt is masked.
And crypto request finish when input *and* outpout buffer are fully
read/write.

About the crash due to unmapped memory, using scatterwalk_copychunks()
that will map and copy each block fix the issue.
Using this api and copying full block will also fix unaligned data
access, avoid early copy of in/out buffer, and make useless the extra
alignment constraint.

Fixes: 9e054ec2 ("crypto: stm32 - Support for STM32 CRYP crypto module")
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

This fixes the lrw autotest if lrw uses the CRYP as the AES block cipher
provider (as ecb(aes)). At end of request, CRYP should not update the IV
in case of ECB chaining mode. Indeed the ECB chaining mode never uses
the IV, but the software LRW chaining mode uses the IV field as
a counter and due to the (unexpected) update done by CRYP while the AES
block process, the counter get a wrong value when the IV overflow.

Fixes: 5f49f18d ("crypto: stm32/cryp - update to return iv_out")
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Delete extraneous lines in probe error handling code: pm was
disabled twice.

Fixes: 65f9aa36 ("crypto: stm32/cryp - Add power management support")
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Some auto tests failed because driver wasn't returning the expected
error with some input size/iv value/tag size.
Now:
 Return 0 early for empty buffer. (We don't need to start the engine for
 an empty input buffer).
 Accept any valid authsize for gcm(aes).
 Return -EINVAL if iv for ccm(aes) is invalid.
 Return -EINVAL if buffer size is a not a multiple of algorithm block size.

Fixes: 9e054ec2 ("crypto: stm32 - Support for STM32 CRYP crypto module")
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Don't erase key:
If key is erased before the crypto_finalize_.*_request() call, some
pending process will run with a key={ 0 }.
Moreover if the key is reset at end of request, it breaks xts chaining
mode, as for last xts block (in case input len is not a multiple of
block) a new AES request is started without calling again set_key().

Fixes: 9e054ec2 ("crypto: stm32 - Support for STM32 CRYP crypto module")
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

STM32 CRYP hardware doesn't manage CTR counter bigger than max U32, as
a workaround, at each block the current IV is saved, if the saved IV
lower u32 is 0xFFFFFFFF, the full IV is manually incremented, and set
in hardware.
Fixes: bbb28326 ("crypto: stm32 - Fix sparse warnings")
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Change driver to not print an error message when the device
probe is deferred for a clock resource.
Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com>
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Change stm32 CRYP driver to defer its probe operation when
reset controller device is registered but has not been probed yet.
Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com>
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Remove a duplicate #include <linux/fips.h>.
Signed-off-by: Guo Zhengkui <guozhengkui@vivo.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

If kstrtoint() fails then "lfs_num" is uninitialized and the warning
doesn't make any sense.  Just delete it.

Fixes: 8ec8015a ("crypto: octeontx2 - add support to process the crypto request")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Use the FIELD_PREP() helper, instead of open-coding the same operation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

When caam queue is full (-ENOSPC), caam frees descriptor memory.
crypto-engine checks if retry support is true and h/w queue
is full(-ENOSPC), then requeue the crypto request.
During processing the requested descriptor again, caam gives below error.
(caam_jr 30902000.jr: 40000006: DECO: desc idx 0: Invalid KEY Command).

This patch adds a check to return when caam input ring is full
and retry support is true. so descriptor memory is not freed
and requeued request can be processed again.

Fixes: 2d653936 ("crypto: caam - enable crypto-engine retry mechanism")
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

On Dec 31 2023 NIST sunsets TDES for FIPS use. To prevent FIPS
validations to be completed in the future to be affected by the TDES
sunsetting, disallow TDES already now. Otherwise a FIPS validation would
need to be "touched again" end 2023 to handle TDES accordingly.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>