- 17 Feb, 2016 6 commits
-
-
Daniel Jurgens authored
The PCI channel could go offline during reset due to EEH. Don't bug on in this case, the error is recoverable. Fixes: f6bc11e4 ('net/mlx4_core: Enhance the catas flow to support device reset') Signed-off-by:
Daniel Jurgens <danielj@mellanox.com> Reviewed-by:
Yishai Hadas <yishaih@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Eran Ben Elisha authored
The error flow in procedure handle_existing_counter() is wrong. The procedure should exit after encountering the error, not continue as if everything is OK. Fixes: 68230242 ('net/mlx4_core: Add port attribute when tracking counters') Signed-off-by:
Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by:
Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Eugenia Emantayev authored
Previously, the shift value used for time-stamping was constant and didn't depend on the HW chip frequency. Change that to take the frequency into account and calculate the maximal value in cycles per wraparound of ten seconds. This time slot was chosen since it gives a good accuracy in time synchronization. Algorithm for shift value calculation: * Round up the maximal value in cycles to nearest power of two * Calculate maximal multiplier by division of all 64 bits set to above result * Then, invert the function clocksource_khz2mult() to get the shift from maximal mult value Fixes: ec693d47 ('net/mlx4_en: Add HW timestamping (TS) support') Signed-off-by:
Eugenia Emantayev <eugenia@mellanox.com> Reviewed-by:
Matan Barak <matanb@mellanox.com> Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Amir Vadai authored
RdropOvflw counts overrun of HW buffer, therefore should be used for rx_fifo_errors only. Currently RdropOvflw counter is mistakenly also set into rx_missed_errors and rx_over_errors too, which makes the device total dropped packets accounting to show wrong results. Fix that. Use it for rx_fifo_errors only. Fixes: c27a02cd ('mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC') Signed-off-by:
Amir Vadai <amir@vadai.me> Signed-off-by:
Eugenia Emantayev <eugenia@mellanox.com> Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Bjørn Mork authored
Thomas reports: T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=05c6 ProdID=6001 Rev=00.00 S: Manufacturer=USB Modem S: Product=USB Modem S: SerialNumber=1234567890ABCDEF C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage Reported-by:
Thomas Schäfer <tschaefer@t-online.de> Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
If tcp_v4_inbound_md5_hash() returns an error, we must release the refcount on the request socket, not on the listener. The bug was added for IPv4 only. Fixes: 079096f1 ("tcp/dccp: install syn_recv requests into ehash table") Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- 16 Feb, 2016 34 commits
-
-
Eric Dumazet authored
There are some cases where rtt_us derives from deltas of jiffies, instead of using usec timestamps. Since we want to track minimal rtt, better to assume a delta of 0 jiffie might be in fact be very close to 1 jiffie. It is kind of sad jiffies_to_usecs(1) calls a function instead of simply using a constant. Fixes: f6722583 ("tcp: track min RTT using windowed min-filter") Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
Neal Cardwell <ncardwell@google.com> Cc: Yuchung Cheng <ycheng@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ken Kawasaki authored
add new id (CONTEC C-NET(PC)C-100TX2) Signed-off-by:
Ken Kawasaki <ken_kawasaki@nifty.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Sascha Hauer authored
The phy has not been initialized, disconnecting it in the error path results in a NULL pointer exception. Drop the phy_disconnect from the error path. Signed-off-by:
Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Acked-by:
Neil Armstrong <narmstrong@baylibre.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Sascha Hauer authored
The Marvell 88E6240 has been tested successfully without further changes. Add entry to the table of supported devices. Signed-off-by:
Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jon Paul Maloy authored
In commit 52666986 ("tipc: let broadcast packet reception use new link receive function") we introduced a new per-node broadcast reception link instance. This link is created at the moment the node itself is created. Unfortunately, the allocation is done after the node instance has already been added to the node lookup hash table. This creates a potential race condition, where arriving broadcast packets are able to find and access the node before it has been fully initialized, and before the above mentioned link has been created. The result is occasional crashes in the function tipc_bcast_rcv(), which is trying to access the not-yet existing link. We fix this by deferring the addition of the node instance until after it has been fully initialized in the function tipc_node_create(). Acked-by:
Ying Xue <ying.xue@windriver.com> Signed-off-by:
Jon Maloy <jon.maloy@ericsson.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Michael Chan says: ==================== bnxt_en: Bug fixes. Fixed autoneg logic and some related cleanups, fixed tx push operation, and reduced default ring sizes. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Michael Chan authored
The current default tx ring size of 512 causes an extra page to be allocated for the tx ring with only 1 entry in it. Reduce it to 511. The default rx ring size is also reduced to 511 to use less memory by default. Signed-off-by:
Michael Chan <mchan@broadcom.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Michael Chan authored
tx push is supported for small packets to reduce DMA latency. The following bugs are fixed in this patch: 1. Fix the definition of the push BD which is different from the DMA BD. 2. The push buffer has to be zero padded to the next 64-bit word boundary or tx checksum won't be correct. 3. Increase the tx push packet threshold to 164 bytes (192 bytes with the BD) so that small tunneled packets are within the threshold. Signed-off-by:
Michael Chan <mchan@broadcom.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Michael Chan authored
20G is not supported by production hardware and only the 40GbaseCR4 standard is supported. Signed-off-by:
Michael Chan <mchan@broadcom.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Michael Chan authored
Cleanup bnxt_probe_phy() to cleanly separate 2 code blocks for autoneg on and off. Autoneg flow control is possible only if autoneg is enabled. In bnxt_get_settings(), Pause and Asym_Pause are always supported. Only the advertisement bits change depending on the ethtool -A setting in auto mode. Signed-off-by:
Michael Chan <mchan@broadcom.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Michael Chan authored
1. Determine autoneg on|off setting from link_info->autoneg. Using the firmware returned setting can be misleading if autoneg is changed and there hasn't been a phy update from the firmware. 2. If autoneg is disabled, link_info->autoneg should be set to 0 to indicate both speed and flow control autoneg are disabled. 3. To enable autoneg flow control, speed autoneg must be enabled. Signed-off-by:
Michael Chan <mchan@broadcom.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Arnd Bergmann authored
A recent change to the mdb code confused the compiler to the point where it did not realize that the port-group returned from br_mdb_add_group() is always valid when the function returns a nonzero return value, so we get a spurious warning: net/bridge/br_mdb.c: In function 'br_mdb_add': net/bridge/br_mdb.c:542:4: error: 'pg' may be used uninitialized in this function [-Werror=maybe-uninitialized] __br_mdb_notify(dev, entry, RTM_NEWMDB, pg); Slightly rearranging the code in br_mdb_add_group() makes the problem go away, as gcc is clever enough to see that both functions check for 'ret != 0'. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Fixes: 9e8430f8 ("bridge: mdb: Passing the port-group pointer to br_mdb module") Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Hariprasad Shenai authored
Signed-off-by:
Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Alexander Kochetkov says: ==================== Fixes for rockchip EMAC Here is a set of 3 patches what fix koops, memory leak and rockchip EMAC hang. Tested on radxarock lite. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Alexander Kochetkov authored
EMAC could be disabled, while there is some sb_buff in use. That buffers got lost for linux. In order to reproduce run on device during active ethernet work: ifconfig eth0 down Signed-off-by:
Alexander Kochetkov <al.kochet@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Alexander Kochetkov authored
EMAC reset internal tx ring pointer to zero at statup. txbd_curr and txbd_dirty can be different from zero. That cause ethernet transfer hang (no packets transmitted). In order to reproduce, run on device: ifconfig eth0 down ifconfig eth0 up Signed-off-by:
Alexander Kochetkov <al.kochet@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Alexander Kochetkov authored
There is a race between arc_emac_tx() and arc_emac_tx_clean(). sk_buff got freed by arc_emac_tx_clean() while arc_emac_tx() submitting sk_buff. In order to free sk_buff arc_emac_tx_clean() checks: if ((info & FOR_EMAC) || !txbd->data) break; ... dev_kfree_skb_irq(skb); If condition false, arc_emac_tx_clean() free sk_buff. In order to submit txbd, arc_emac_tx() do: priv->tx_buff[*txbd_curr].skb = skb; ... priv->txbd[*txbd_curr].data = cpu_to_le32(addr); ... ... <== arc_emac_tx_clean() check condition here ... <== (info & FOR_EMAC) is false ... <== !txbd->data is false ... *info = cpu_to_le32(FOR_EMAC | FIRST_OR_LAST_MASK | len); In order to reproduce the situation, run device: # iperf -s run on host: # iperf -t 600 -c <device-ip-addr> [ 28.396284] ------------[ cut here ]------------ [ 28.400912] kernel BUG at .../net/core/skbuff.c:1355! [ 28.414019] Internal error: Oops - BUG: 0 [#1] SMP ARM [ 28.419150] Modules linked in: [ 28.422219] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G B 4.4.0+ #120 [ 28.429516] Hardware name: Rockchip (Device Tree) [ 28.434216] task: c0665070 ti: c0660000 task.ti: c0660000 [ 28.439622] PC is at skb_put+0x10/0x54 [ 28.443381] LR is at arc_emac_poll+0x260/0x474 [ 28.447821] pc : [<c03af580>] lr : [<c028fec4>] psr: a0070113 [ 28.447821] sp : c0661e58 ip : eea68502 fp : ef377000 [ 28.459280] r10: 0000012c r9 : f08b2000 r8 : eeb57100 [ 28.464498] r7 : 00000000 r6 : ef376594 r5 : 00000077 r4 : ef376000 [ 28.471015] r3 : 0030488b r2 : ef13e880 r1 : 000005ee r0 : eeb57100 [ 28.477534] Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none [ 28.484658] Control: 10c5387d Table: 8eaf004a DAC: 00000051 [ 28.490396] Process swapper/0 (pid: 0, stack limit = 0xc0660210) [ 28.496393] Stack: (0xc0661e58 to 0xc0662000) [ 28.500745] 1e40: 00000002 00000000 [ 28.508913] 1e60: 00000000 ef376520 00000028 f08b23b8 00000000 ef376520 ef7b6900 c028fc64 [ 28.517082] 1e80: 2f158000 c0661ea8 c0661eb0 0000012c c065e900 c03bdeac ffff95e9 c0662100 [ 28.525250] 1ea0: c0663924 00000028 c0661ea8 c0661ea8 c0661eb0 c0661eb0 0000001e c0660000 [ 28.533417] 1ec0: 40000003 00000008 c0695a00 0000000a c066208c 00000100 c0661ee0 c0027410 [ 28.541584] 1ee0: ef0fb700 2f158000 00200000 ffff95e8 00000004 c0662100 c0662080 00000003 [ 28.549751] 1f00: 00000000 00000000 00000000 c065b45c 0000001e ef005000 c0647a30 00000000 [ 28.557919] 1f20: 00000000 c0027798 00000000 c005cf40 f0802100 c0662ffc c0661f60 f0803100 [ 28.566088] 1f40: c0661fb8 c00093bc c000ffb4 60070013 ffffffff c0661f94 c0661fb8 c00137d4 [ 28.574267] 1f60: 00000001 00000000 00000000 c001ffa0 00000000 c0660000 00000000 c065a364 [ 28.582441] 1f80: c0661fb8 c0647a30 00000000 00000000 00000000 c0661fb0 c000ffb0 c000ffb4 [ 28.590608] 1fa0: 60070013 ffffffff 00000051 00000000 00000000 c005496c c0662400 c061bc40 [ 28.598776] 1fc0: ffffffff ffffffff 00000000 c061b680 00000000 c0647a30 00000000 c0695294 [ 28.606943] 1fe0: c0662488 c0647a2c c066619c 6000406a 413fc090 6000807c 00000000 00000000 [ 28.615127] [<c03af580>] (skb_put) from [<ef376520>] (0xef376520) [ 28.621218] Code: e5902054 e590c090 e3520000 0a000000 (e7f001f2) [ 28.627307] ---[ end trace 4824734e2243fdb6 ]--- [ 34.377068] Internal error: Oops: 17 [#1] SMP ARM [ 34.382854] Modules linked in: [ 34.385947] CPU: 0 PID: 3 Comm: ksoftirqd/0 Not tainted 4.4.0+ #120 [ 34.392219] Hardware name: Rockchip (Device Tree) [ 34.396937] task: ef02d040 ti: ef05c000 task.ti: ef05c000 [ 34.402376] PC is at __dev_kfree_skb_irq+0x4/0x80 [ 34.407121] LR is at arc_emac_poll+0x130/0x474 [ 34.411583] pc : [<c03bb640>] lr : [<c028fd94>] psr: 60030013 [ 34.411583] sp : ef05de68 ip : 0008e83c fp : ef377000 [ 34.423062] r10: c001bec4 r9 : 00000000 r8 : f08b24c8 [ 34.428296] r7 : f08b2400 r6 : 00000075 r5 : 00000019 r4 : ef376000 [ 34.434827] r3 : 00060000 r2 : 00000042 r1 : 00000001 r0 : 00000000 [ 34.441365] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none [ 34.448507] Control: 10c5387d Table: 8f25c04a DAC: 00000051 [ 34.454262] Process ksoftirqd/0 (pid: 3, stack limit = 0xef05c210) [ 34.460449] Stack: (0xef05de68 to 0xef05e000) [ 34.464827] de60: ef376000 c028fd94 00000000 c0669480 c0669480 ef376520 [ 34.473022] de80: 00000028 00000001 00002ae4 ef376520 ef7b6900 c028fc64 2f158000 ef05dec0 [ 34.481215] dea0: ef05dec8 0000012c c065e900 c03bdeac ffff983f c0662100 c0663924 00000028 [ 34.489409] dec0: ef05dec0 ef05dec0 ef05dec8 ef05dec8 ef7b6000 ef05c000 40000003 00000008 [ 34.497600] dee0: c0695a00 0000000a c066208c 00000100 ef05def8 c0027410 ef7b6000 40000000 [ 34.505795] df00: 04208040 ffff983e 00000004 c0662100 c0662080 00000003 ef05c000 ef027340 [ 34.513985] df20: ef05c000 c0666c2c 00000000 00000001 00000002 00000000 00000000 c0027568 [ 34.522176] df40: ef027340 c003ef48 ef027300 00000000 ef027340 c003edd4 00000000 00000000 [ 34.530367] df60: 00000000 c003c37c ffffff7f 00000001 00000000 ef027340 00000000 00030003 [ 34.538559] df80: ef05df80 ef05df80 00000000 00000000 ef05df90 ef05df90 ef05dfac ef027300 [ 34.546750] dfa0: c003c2a4 00000000 00000000 c000f578 00000000 00000000 00000000 00000000 [ 34.554939] dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 34.563129] dfe0: 00000000 00000000 00000000 00000000 00000013 00000000 ffffffff dfff7fff [ 34.571360] [<c03bb640>] (__dev_kfree_skb_irq) from [<c028fd94>] (arc_emac_poll+0x130/0x474) [ 34.579840] [<c028fd94>] (arc_emac_poll) from [<c03bdeac>] (net_rx_action+0xdc/0x28c) [ 34.587712] [<c03bdeac>] (net_rx_action) from [<c0027410>] (__do_softirq+0xcc/0x1f8) [ 34.595482] [<c0027410>] (__do_softirq) from [<c0027568>] (run_ksoftirqd+0x2c/0x50) [ 34.603168] [<c0027568>] (run_ksoftirqd) from [<c003ef48>] (smpboot_thread_fn+0x174/0x18c) [ 34.611466] [<c003ef48>] (smpboot_thread_fn) from [<c003c37c>] (kthread+0xd8/0xec) [ 34.619075] [<c003c37c>] (kthread) from [<c000f578>] (ret_from_fork+0x14/0x3c) [ 34.626317] Code: e8bd8010 e3a00000 e12fff1e e92d4010 (e59030a4) [ 34.632572] ---[ end trace cca5a3d86a82249a ]--- Signed-off-by:
Alexander Kochetkov <al.kochet@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Alexander Duyck authored
This patch corrects the unaligned accesses seen on GRE TEB tunnels when generating hash keys. Specifically what this patch does is make it so that we force the use of skb_copy_bits when the GRE inner headers will be unaligned due to NET_IP_ALIGNED being a non-zero value. Signed-off-by:
Alexander Duyck <aduyck@mirantis.com> Acked-by:
Tom Herbert <tom@herbertland.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Saeed Mahameed says: ==================== mlx5 driver fixes for 4.5-rc2 We added here a patch from Matan and Alaa for addressing Linus comments on the mess w.r.t reserved field names in the driver/firmware auto-generated file. Once the patch hits linus tree, we'll ask Doug to rebase his tree on that rc so both net-next and rdma-next development for 4.6 will be done under the fixed robust form. Also provided two patches that addresses the dynamic ndo initialization issue of mlx5e netdevice. Or and Saeed. changes from V1: (Only first patch was changed) In this V we fixed the issues addressed in Or's previous e-mail. 1. Offsets took into account two dimensional u8 arrays 2. Offsets took into account nesting unions and structs 3. Offsets for unions 4. Offsets for any reserved field ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Saeed Mahameed authored
Currently our netdevice ops is a one static global variable which is referenced by all mlx5e netdevice instances. This can be problematic when different driver instances do not share same HW capabilities (e.g SRIOV PF and VFs probed to the host). Now we have two constant global netdevice ops variables, one for basic netdevice ops and the other with extended SRIOV ops, on netdevice construction we choose the one suitable for current device capabilities. Fixes: 66e49ded ("net/mlx5e: Add support for SR-IOV ndos") Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Saeed Mahameed authored
Currently mlx5e_select_queue is redundant since num_tc is always 1. Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Matan Barak authored
mlx5_ifc.h is a header file representing the API and ABI between the driver to the firmware and hardware. This file is used from both the mlx5_ib and mlx5_core drivers. Previously, this file used incrementing counter to indicate reserved fields, for example: struct mlx5_ifc_odp_per_transport_service_cap_bits { u8 send[0x1]; u8 receive[0x1]; u8 write[0x1]; u8 read[0x1]; u8 reserved_0[0x1]; u8 srq_receive[0x1]; u8 reserved_1[0x1a]; }; If one developer implements through net-next feature A that uses reserved_0, they replace it with featureA and renames reserved_1 to reserved_0. In the same kernel cycle, a 2nd developer could implement feature B through the rdma tree, that uses reserved_1 and split it to featureB and a smaller reserved_1 field. This will cause a conflict when the two trees are merged. The source of this conflict is that the 1st developer changed *all* reserved fields. As Linus suggested, we change the layout of structs to: struct mlx5_ifc_odp_per_transport_service_cap_bits { u8 send[0x1]; u8 receive[0x1]; u8 write[0x1]; u8 read[0x1]; u8 reserved_at_4[0x1]; u8 srq_receive[0x1]; u8 reserved_at_6[0x1a]; }; This makes the conflicts much more rare and preserves the locality of changes. Signed-off-by:
Matan Barak <matanb@mellanox.com> Signed-off-by:
Alaa Hleihel <alaa@mellanox.com> Reported-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jay Vosburgh authored
There is presently a race condition between the bonding periodic link monitor and the updating of a slave's speed and duplex. The former occurs on a periodic basis, and the latter in response to a driver's calling of netif_carrier_on. It is possible for the periodic monitor to run between the driver call of netif_carrier_on and the receipt of the NETDEV_CHANGE event that causes bonding to update the slave's speed and duplex. This manifests most notably as a report that a slave is up and "0 Mbps full duplex" after enslavement, but in principle could report an incorrect speed and duplex after any link up event if the device comes up with a different speed or duplex. This affects the 802.3ad aggregator selection, as the speed and duplex are selection criteria. This is fixed by updating the speed and duplex in the periodic monitor, prior to using that information. This was done historically in bonding, but the call to bond_update_speed_duplex was removed in commit 876254ae ("bonding: don't call update_speed_duplex() under spinlocks"), as it might sleep under lock. Later, the locking was changed to only hold RTNL, and so after commit 876254ae ("bonding: don't call update_speed_duplex() under spinlocks") this call is again safe. Tested-by:
"Tantilov, Emil S" <emil.s.tantilov@intel.com> Cc: Veaceslav Falico <vfalico@gmail.com> Cc: dingtianhong <dingtianhong@huawei.com> Fixes: 876254ae ("bonding: don't call update_speed_duplex() under spinlocks") Signed-off-by:
Jay Vosburgh <jay.vosburgh@canonical.com> Acked-by:
Ding Tianhong <dingtianhong@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Arnd Bergmann authored
The am79c961a.c driver fails to build with clang because of an unusual inline assembly construct: drivers/net/ethernet/amd/am79c961a.c:53:7: error: invalid % escape in inline assembly string "str%?h %1, [%2] @ NET_RAP\n\t" The same change has been done a decade ago in arch/arm as of 6a39dd62 ("[ARM] 3759/2: Remove uses of %?"), but apparently some drivers were missed. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Acked-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Robert Jarzmik authored
The smc91x driver doesn't honor the probe deferral mechanism when the interrupt source is not yet available, such as one provided by a gpio controller not probed. Fix this by propagating the platform_get_irq() error code as the probe return value. Signed-off-by:
Robert Jarzmik <robert.jarzmik@free.fr> Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Florian Fainelli says: ==================== Subject: [PATCH net v2 0/4] net: phy: bcm7xxx 40nm PHY fixes Here is a collection of fixes for the 40nm Ethernet PHY supported by the 7xxx PHY driver, please also queue these fixes for stable. Changes in v2: - dropped the cleanup patch, not appropriate - added another patch removing bogus wildcard entries ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
Remove the two wildcard entries, they serve no purpose and will match way too many devices, some of them being covered by the driver in drivers/net/phy/broadcom.c. Remove the now unused bcm7xxx_dummy_config_init() function which would produce a warning. Fixes: b560a58c ("net: phy: add Broadcom BCM7xxx internal PHY driver") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
Since we were wrongly advertising gigabit features for these 10/100 only Ethernet PHYs, bcm7xxx_config_init() which is supposed to apply workaround would have not run since the check would be true, now that we have fixed the PHY features, remove that check since it has no reasoning to be there anymore. Fixes: e18556ee ("net: phy: bcm7xxx: do not use PHY_BRCM_100MBPS_WAR") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
The PHY entries for BCM7425/29/35 declare the 40nm Ethernet PHY as being 10/100/1000 capable, while this is just a 10/100 capable PHY device, fix that. Fixes: d068b02c ("net: phy: add BCM7425 and BCM7429 PHYs") Fixes: 9458ceab ("net: phy: bcm7xxx: Add entry for BCM7435") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
The clear and set masks in the call to phy_set_clr_bits() called from bcm7xxx_config_init() are inverted. We need to fix this by swapping the two arguments, that is, set 0 bits, but clear the shade mode 2 enable bit. Fixes: b560a58c ("net: phy: add Broadcom BCM7xxx internal PHY driver") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Sergei Shtylyov says: ==================== ravb: fix the fallout of R-Car gen3 gPTP support Here's a set of 2 patches against DaveM's 'net.git' repo fixing up the incomplete commit f5d7837f ("ravb: ptp: Add CONFIG mode support"). I'm proposing these as fixes but they can be merged as cleanups as well... [1/2] ravb: kill duplicate setting of CCC.CSEL [2/2] ravb: skip gPTP start/stop on R-Car gen3 ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Sergei Shtylyov authored
When adding support for the R-Car gen3 gPTP active in configuration mode, some call sites of ravb_ptp_{init|stop}() were missed due to an oversight. Add checks for the R-Car gen2 SoCs around these... Fixes: f5d7837f ("ravb: ptp: Add CONFIG mode support") Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Sergei Shtylyov authored
When adding support for the R-Car gen3 gPTP active in configuration mode, the code setting the CCC.CSEL field was duplicated due to an oversight. For R-Car gen 2 it's just redundant and for R-Car gen3 the write at this time is probably ignored due to CCC.GAC bit being already set... Fixes: f5d7837f ("ravb: ptp: Add CONFIG mode support") Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nfDavid S. Miller authored
Pablo Neira Ayuso says: ==================== Netfilter fixes for net The following patchset contain a rather large batch for your net that includes accumulated bugfixes, they are: 1) Run conntrack cleanup from workqueue process context to avoid hitting soft lockup via watchdog for large tables. This is required by the IPv6 masquerading extension. From Florian Westphal. 2) Use original skbuff from nfnetlink batch when calling netlink_ack() on error since this needs to access the skb->sk pointer. 3) Incremental fix on top of recent Sasha Levin's lock fix for conntrack resizing. 4) Fix several problems in nfnetlink batch message header sanitization and error handling, from Phil Turnbull. 5) Select NF_DUP_IPV6 based on CONFIG_IPV6, from Arnd Bergmann. 6) Fix wrong signess in return values on nf_tables counter expression, from Anton Protopopov. Due to the NetDev 1.1 organization burden, I had no chance to pass up this to you any sooner in this release cycle, sorry about that. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-