*ep->reg_udccs is always set to 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

In the non highmem case, if two memory banks of 1GB each are provided,
the second bank would evade suppression since its virtual base would
be 0.  Fix this by disallowing any memory bank which virtual base
address is found to be lower than PAGE_OFFSET.
Reported-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The GPIO interrupts can be configured as either level triggered or edge
triggered, with a default of level triggered.  When an edge triggered
interrupt is requested, the gpio_irq_set_type method is called which
currently switches the given IRQ descriptor between two struct irq_chip
instances: orion_gpio_irq_level_chip and orion_gpio_irq_edge_chip. This
happens via __setup_irq() which also calls irq_chip_set_defaults() to
assign default methods to uninitialized ones.  The problem is that
irq_chip_set_defaults() is called before the irq_chip reference is
switched, leaving the new irq_chip (orion_gpio_irq_edge_chip in this
case) with uninitialized methods such as chip->startup() causing a kernel
oops.

Many solutions are possible, such as making irq_chip_set_defaults() global
and calling it from gpio_irq_set_type(), or calling __irq_set_trigger()
before irq_chip_set_defaults() in __setup_irq().  But those require
modifications to the generic IRQ code which might have adverse effect on
other architectures, and that would still be a fragile arrangement.
Manually copying the missing methods from within gpio_irq_set_type()
would be really ugly and it would break again the day new methods with
automatic defaults are added.

A better solution is to have a single irq_chip instance which can deal
with both edge and level triggered interrupts.  It is also a good idea
to switch the IRQ handler instead, as the edge IRQ handler allows for
one edge IRQ event to be queued as the IRQ is actually masked only when
that second IRQ is received, at which point the hardware can queue an
additional IRQ event, making edge triggered interrupts a bit more
reliable.
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Add support for inverted rdy_busy pin for Atmel nand device controller
It will fix building error on NeoCore926 board.
Acked-by: Andrew Victor <linux@maxim.org.za>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Gregory CLEMENT <gclement@adeneo.adetelgroup.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Enable the GPIO clocks earlier in the initialization sequence.  This
allow the board-setup code to read and set GPIO pins.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The recently merged AT91SAM9 watchdog driver uses the
AT91SAM9X_WATCHDOG config variable, whereas the original version of
the driver (and the platform support code) used AT91SAM9_WATCHDOG.
This causes the watchdog platform_device to never be registered, and
therefore the driver not to be initialized.

This patch:
- updates the platform support code to use AT91SAM9X_WATCHDOG.
- includes <linux/io.h> to fix compile error (same fix as was applied
to at91rm9200_wdt.c)
- fixes comment regarding watchdog clock-rates in at91rm9200.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Add Wan ZongShun to MAINTAINERS for W90P910.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

_omap2_clksel_get_src_field() was returning the first entry which was
either the default _or_ applicable to the SoC.  This is wrong - we
should be returning the first default which is applicable to the SoC.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The error checks for omap2_divisor_to_clksel() and comment disagree with
the actual value returned on error.  Fix this to return the correct error
value.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ASoC: Only register AC97 bus if it's not done already
  ALSA: hda - Add snd_hda_multi_out_dig_cleanup()
  ALSA: hda - Add missing terminator in slave dig-out array
  ALSA: hda - Change HP dv7 (103c:30f4) quirk from hp-m4 to hp-dv5 model
  ALSA: hda - Register (new) devices at reconfig
  ALSA: mtpav - Fix initial value for input hwport
  ALSA: hda - add id for Intel IbexPeak integrated HDMI codec
  ALSA: hda - compute checksum in HDMI audio infoframe
  ALSA: hda - enable HDMI audio pin out at module loading time
  ALSA: hda - allow multi-channel HDMI audio playback when ELD is not present
  ASoC: Update SDP3430 machine driver for snd_soc_card
  ALSA: hda - Add quirk for Asus z37e (1043:8284)
  sound: Remove OSSlib stuff from linux/soundcard.h
  ASoC: WM8990: Fix kcontrol's private value use in put callback
  ASoC: TLV320AIC3X: Fix kcontrol's private value use in put callback

uids in namespaces other than init don't get a sysfs entry.

For those in the init namespace, while we're waiting to remove
the sysfs entry for the uid the uid is still hashed, and
alloc_uid() may re-grab that uid without getting a new
reference to the user_ns, which we've already put in free_user
before scheduling remove_user_sysfs_dir().
Reported-and-tested-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Acked-by: David Howells <dhowells@redhat.com>
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ASoC supports both explicit codec drivers for AC97 devices and a simple
driver which uses the standard ALSA AC97 framework for codec support.
When used with the generic AC97 codec support that will provide the
ad hoc AC97 device for drivers like touchscreens to attach to so the
core shouldn't do so.
Reported-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Added the helper function snd_hda_multi_out_dig_cleanup() to clean up
the digital outputs with multi setup.  This call is needed in cases
the codec supports multiple digital outputs as slaves.  Otherwise the
slave widgets aren't properly cleaned up.

For a single digital output (e.g. in patch_conexant.c), this call isn't
needed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Added the missing terminator for ad1989b_slave_dig_outs[].

Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Change HP dv7 quirk: although reported to work with hp-m4 model
(https://bugzilla.novell.com/show_bug.cgi?id=445321), the original
report doesn't contain info about testing of internal microphone.

Recently I received a report about internal mic not working
(https://qa.mandriva.com/show_bug.cgi?id=44855#c193), this must be
related with the forced line in on pin 0x0e done with hp-m4 model. Thus
change the current quirk from STAC_HP_M4 to STAC_HP_DV5, later reported
to be fixed on a provided kernel with this change
(https://qa.mandriva.com/show_bug.cgi?id=44855#c196).
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (32 commits)
  wimax: fix oops in wimax_dev_get_by_genl_info() when looking up non-wimax iface
  net: 4 bytes kernel memory disclosure in SO_BSDCOMPAT gsopt try #2
  netxen: fix compile waring "label ‘set_32_bit_mask’ defined but not used" on IA64 platform
  bnx2: Update version to 1.9.2 and copyright.
  bnx2: Fix jumbo frames error handling.
  bnx2: Update 5709 firmware.
  bnx2: Update 5706/5708 firmware.
  3c505: do not set pcb->data.raw beyond its size
  Documentation/connector/cn_test.c: don't use gfp_any()
  net: don't use in_atomic() in gfp_any()
  IRDA: cnt is off by 1
  netxen: remove pcie workaround
  sun3: print when lance_open() fails
  qlge: bugfix: Add missing rx buf clean index on early exit.
  qlge: bugfix: Fix RX scaling values.
  qlge: bugfix: Fix TSO breakage.
  qlge: bugfix: Add missing dev_kfree_skb_any() call.
  qlge: bugfix: Add missing put_page() call.
  qlge: bugfix: Fix fatal error recovery hang.
  qlge: bugfix: Use netif_receive_skb() and vlan_hwaccel_receive_skb().
  ...

When a non-wimax interface is looked up by the stack, a bad pointer is
returned when the looked-up interface is not found in the list (of
registered WiMAX interfaces). This causes an oops in the caller when
trying to use the pointer.

Fix by properly setting the pointer to NULL if we don't exit from the
list_for_each() with a found entry.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In function sock_getsockopt() located in net/core/sock.c, optval v.val
is not correctly initialized and directly returned in userland in case
we have SO_BSDCOMPAT option set.

This dummy code should trigger the bug:

int main(void)
{
	unsigned char buf[4] = { 0, 0, 0, 0 };
	int len;
	int sock;
	sock = socket(33, 2, 2);
	getsockopt(sock, 1, SO_BSDCOMPAT, &buf, &len);
	printf("%x%x%x%x\n", buf[0], buf[1], buf[2], buf[3]);
	close(sock);
}

Here is a patch that fix this bug by initalizing v.val just after its
declaration.
Signed-off-by: Clément Lecigne <clement.lecigne@netasq.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When compile the latest kernel on IA64 platform,I got a warning:
drivers/net/netxen/netxen_nic_main.c:203: warning: label ‘set_32_bit_mask’ 
defined but not used

We do not need label ‘set_32_bit_mask’  on IA64 platform,So move it to #else.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If errors are reported on a frame descriptor, we need to
account for the buffer pages that may have been used for this
error packet and recycle them.  Otherwise, we may get the wrong
pages for the next packet.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

New firmware fixes a data corruption issue when receiving and
placing jumbo frames into host buffers.  In some cases, the
buffer descriptor is not updated correctly and this will lead
to the driver linking the wrong number of pages into the SKB.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

New firmware fixes a data corruption issue when receiving and
placing jumbo frames into host buffers.  In some cases, the
buffer descriptor is not updated correctly and this will lead
to the driver linking the wrong number of pages into the SKB.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ensure that we do not set pcb->data.raw beyond its size, print an error message
and return false if we attempt to. A timout message was printed one too early.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cn_test_timer_func() is a timer handler and can never use GFP_KERNEL -
there's no point in using gfp_any() here.

Also, use setup_timer().
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The problem is that in_atomic() will return false inside spinlocks if
CONFIG_PREEMPT=n.  This will lead to deadlockable GFP_KERNEL allocations
from spinlocked regions.

Secondly, if CONFIG_PREEMPT=y, this bug solves itself because networking
will instead use GFP_ATOMIC from this callsite.  Hence we won't get the
might_sleep() debugging warnings which would have informed us of the buggy
callsites.

Solve both these problems by switching to in_interrupt().  Now, if someone
runs a gfp_any() allocation from inside spinlock we will get the warning
if CONFIG_PREEMPT=y.

I reviewed all callsites and most of them were too complex for my little
brain and none of them documented their interface requirements.  I have no
idea what this patch will do.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

If no prior break occurs, cnt reaches 101 after the loop, so we are still able
to change speed when cnt has become 100.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove workaround for pcie bug in early revisions of NX3031
(rev 41 or earlier). This is taken care of during firmware init.

The workaround required writing pcie config reg of every
pcie function on a card, not all of which are enabled.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With while (--i > 0) { ... } i reaches 0; print when lance_open() fails
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The large receive buffer queue is not properly tracking the current
index in the case where an early exit occurs.  This can happen when a
page alloc or dma mapping fails.  If this occurs the queue will get
out of sync and invalid indexes can be written to the hardware.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Receive packets were only scaling across 2 of the receive queues. The
value was hardcoded to 2 instead of being based on how many rx queues
were running.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Moved the buffer mapping to a point after TSO logic has modified the
iph->check field. We were seeing stale data on the PCIe bus.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We put the skb back if we can't get mapping for it.  We don't
want unmapped buffers on our receive buffer queue.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We put the page back if we can't get mapping for it.  We don't
want unmapped buffers on our receive buffer queue.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>