Add FW ABI defines and code for basic init of TLS offload.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Parse TLV containing a bitmask of supported crypto operations.
The TLV contains a capability bitmask (supported operations)
and enabled bitmask.  Each operation describes the crypto
protocol quite exhaustively (protocol, AEAD, direction).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

FW may prefer to handle some communication via a mailbox
or the vNIC may simply not have a control queue (VFs).
Add a way of exchanging ccm-compatible messages via a
mailbox.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Parse the mailbox TLV.  When control message queue is not available
we can fall back to passing the control messages via the vNIC
mailbox.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We will need to release the bar lock from a workqueue
so move from a mutex to a semaphore.  This lock should
not be too hot.  Unfortunately semaphores don't have
lockdep support.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently if we need to modify the head of the skb and allocation
fails we would free the skb and not increment the error counter.
Make sure all errors are counted.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add 1000BaseX to the link modes which are detected based on the
MII_ESTATUS register as per 802.3 Clause 22. This allows PHYs which
support 1000BaseX to work properly with drivers using phylink.

Previously 1000BaseX support was not detected, and if that was the only
mode the PHY indicated support for, phylink would refuse to attach it
due to the list of supported modes being empty.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix sparse warning:

drivers/net/ethernet/mscc/ocelot_ace.c:96:3:
 warning: symbol 'vcap_data_t' was not declared. Should it be static?

'vcap_data_t' never used so can be removed
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a valid MAC address is not found the current messages
are shown:

fec 2188000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00
fec 2188000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: aa:9f:25:eb:7e:aa

Since the network device has not been registered at this point, it is better
to use dev_err()/dev_info() instead, which will provide cleaner log
messages like these:

fec 2188000.ethernet: Invalid MAC address: 00:00:00:00:00:00
fec 2188000.ethernet: Using random MAC address: aa:9f:25:eb:7e:aa

Tested on a imx6dl-pico-pi board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The monolithic hash_lock could cause huge contention when
inserting/deletiing vxlan_fdbs into the fdb_head.

Use FDB_HASH_SIZE hash_locks to protect insertions/deletions
of vxlan_fdbs into the fdb_head hash table.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Litao jiao <jiaolitao@raisecom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a spelling mistake in a NL_SET_ERR_MSG message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The opts[] array is of type u32. Therefore remove the wrong
cpu_to_le32(). The opts[] array members are converted to little endian
later when being assigned to the respective descriptor fields.

This is not a new issue, it just popped up due to r8169.c having
been renamed and more thoroughly checked. Due to the renaming
this patch applies to net-next only.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
ipv6: tcp: more control on RST flowlabels

First patch allows to reflect incoming IPv6 flowlabel
on RST packets sent when no socket could handle the packet.

Second patch makes sure we send the same flowlabel
for RST or ACK packets on behalf of TIME_WAIT sockets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit 1d13a96c ("ipv6: tcp: fix flowlabel value in ACK
messages"), we stored in tw_flowlabel the flowlabel, in the
case ACK packets needed to be sent on behalf of a TIME_WAIT socket.

We can use the same field so that RST packets sent from
TIME_WAIT state also use a consistent flowlabel.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Florent Fourcot <florent.fourcot@wifirst.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

When RST packets are sent because no socket could be found,
it makes sense to use flowlabel_reflect sysctl to decide
if a reflection of the flowlabel is requested.

This extends commit 22b6722b ("ipv6: Add sysctl for per
namespace flow label reflection"), for some TCP RST packets.

In order to provide full control of this new feature,
flowlabel_reflect becomes a bitmask.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct objagg_stats {
	...
        struct objagg_obj_stats_info stats_info[];
};

size = sizeof(*objagg_stats) + sizeof(objagg_stats->stats_info[0]) * count;
instance = kzalloc(size, GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = kzalloc(struct_size(instance, stats_info, count), GFP_KERNEL);

Notice that, in this case, variable alloc_size is not necessary, hence it
is removed.

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

small cleanup: "struct request_sock_queue *queue" parameter of reqsk_queue_unlink
func is never used in the func, so we can remove it.
Signed-off-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the early days of phylib we had a functionality that changed to the
next lower speed in fixed mode if no link was established after a
certain period of time. This functionality has been removed years ago,
and state PHY_FORCING isn't needed any longer. Instead we can go from
UP to RUNNING or NOLINK directly (same as in autoneg mode).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The variable cache_allocs is to indicate how many frags (KiB) are in one
rds connection frag cache.
The command "rds-info -Iv" will output the rds connection cache
statistics as below:
"
RDS IB Connections:
      LocalAddr RemoteAddr Tos SL  LocalDev            RemoteDev
      1.1.1.14 1.1.1.14   58 255  fe80::2:c903:a:7a31 fe80::2:c903:a:7a31
      send_wr=256, recv_wr=1024, send_sge=8, rdma_mr_max=4096,
      rdma_mr_size=257, cache_allocs=12
"
This means that there are about 12KiB frag in this rds connection frag
cache.
Since rds.h in rds-tools is not related with the kernel rds.h, the change
in kernel rds.h does not affect rds-tools.
rds-info in rds-tools 2.0.5 and 2.0.6 is tested with this commit. It works
well.
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Biao Huang says:

====================
complete dwmac-mediatek driver and fix flow control issue

Changes in v2:
        patch#1: there is no extra action in mediatek_dwmac_remove, remove it

v1:
This series mainly complete dwmac-mediatek driver:
        1. add power on/off operations for dwmac-mediatek.
        2. disable rx watchdog to reduce rx path reponding time.
        3. change the default value of tx-frames from 25 to 1, so
           ptp4l will test pass by default.

and also fix the issue that flow control won't be disabled any more
once being enabled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Current dwmac4_flow_ctrl will not clear
GMAC_RX_FLOW_CTRL_RFE/GMAC_RX_FLOW_CTRL_RFE bits,
so MAC hw will keep flow control on although expecting
flow control off by ethtool. Add codes to fix it.

Fixes: 477286b5 ("stmmac: add GMAC4 core support")
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

the default value of tx-frames is 25, it's too late when
passing tstamp to stack, then the ptp4l will fail:

ptp4l -i eth0 -f gPTP.cfg -m
ptp4l: selected /dev/ptp0 as PTP clock
ptp4l: port 1: INITIALIZING to LISTENING on INITIALIZE
ptp4l: port 0: INITIALIZING to LISTENING on INITIALIZE
ptp4l: port 1: link up
ptp4l: timed out while polling for tx timestamp
ptp4l: increasing tx_timestamp_timeout may correct this issue,
       but it is likely caused by a driver bug
ptp4l: port 1: send peer delay response failed
ptp4l: port 1: LISTENING to FAULTY on FAULT_DETECTED (FT_UNSPECIFIED)

ptp4l tests pass when changing the tx-frames from 25 to 1 with
ethtool -C option.
It should be fine to set tx-frames default value to 1, so ptp4l will pass
by default.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

disable rx watchdog for dwmac-mediatek, then the hw will
issue a rx interrupt once receiving a packet, so the responding time
for rx path will be reduced.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

add Ethernet power on/off operations in init/exit flow.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IS_ERR() already calls unlikely(), so this extra likely() call
around the !IS_ERR() is not needed.
Signed-off-by: Enrico Weigelt <info@metux.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

IS_ERR() already calls unlikely(), so this extra unlikely() call
around IS_ERR() is not needed.
Signed-off-by: Enrico Weigelt <info@metux.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

IS_ERR() already calls unlikely(), so this extra unlikely() call
around IS_ERR() is not needed.
Signed-off-by: Enrico Weigelt <info@metux.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

IS_ERR() already calls unlikely(), so this extra likely() call
around the !IS_ERR() is not needed.
Signed-off-by: Enrico Weigelt <info@metux.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

IS_ERR() already calls unlikely(), so this extra likely() call
around the !IS_ERR() is not needed.
Signed-off-by: Enrico Weigelt <info@metux.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct nfp_tun_active_tuns {
	...
        struct route_ip_info {
                __be32 ipv4;
                __be32 egress_port;
                __be32 extra[2];
        } tun_info[];
};

Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.

So, replace the following form:

sizeof(struct nfp_tun_active_tuns) + sizeof(struct route_ip_info) * count

with:

struct_size(payload, tun_info, count)

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PF driver state flag __I40E_VIRTCHNL_OP_PENDING needs to be
checked and set at the beginning of i40e_ndo_set_vf_mac. Otherwise,
if there are error conditions before it, the flag will be cleared
unexpectedly by this function to cause potential race conditions.
Hence move the check to the top of this function.
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The VF configuration returned in i40e_ndo_get_vf_config is
already stored by the PF. There is no dependency on any
specific state of the VF to return the configuration.
Drop the check against I40E_VF_STATE_INIT since it is not
needed.
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
10GbE Intel Wired LAN Driver Updates 2019-06-05

This series contains updates to mainly ixgbe, with a few updates to
i40e, net, ice and hns2 driver.

Jan adds support for tracking each queue pair for whether or not AF_XDP
zero copy is enabled.  Also updated the ixgbe driver to use the
netdev-provided umems so that we do not need to contain these structures
in our own adapter structure.

William Tu provides two fixes for AF_XDP statistics which were causing
incorrect counts.

Jake reduces the PTP transmit timestamp timeout from 15 seconds to 1 second,
which is still well after the maximum expected delay.  Also fixes an
issues with the PTP SDP pin setup which was not properly aligning on a
full second, so updated the code to account for the cyclecounter
multiplier and simplify the code to make the intent of the calculations
more clear.  Updated the function header comments to help with the code
documentation.  Added support for SDP/PPS output for x550 devices, which
is slightly different than x540 devices that currently have this
support.

Anirudh adds a new define for Link Layer Discovery Protocol to the
networking core, so that drivers do not have to create and use their own
definitions.  In addition, update all the drivers currently defining
their own LLDP define to use the new networking core define.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If ixgbevf_write_msg_read_ack fails, return its error code upstream
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Similar to the X540 hardware, enable support for generating a 1pps
output signal on SDP0.

This support is slightly different to the X540 hardware, because of the
register layout changes. First, the system time register is now
represented in 'cycles' and 'billions of cycles'. Second, we need to
also program the TSSDP register, as well as the ESDP register. Third,
the clock output uses only FREQOUT, instead of a full 64bit value for
the output clock period. Finally, we have to use the ST0 bit instead of
the SYNCLK bit in the TSAUXC register.

This support should work even for the hardware with a higher frequency
clock, as it carefully takes into account the multiply and shift of the
cycle counter used.

We also set the pps configuration to 1, since we now support generating
a pulse per second output.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove references to HCLGE_MAC_ETHERTYPE_LLDP and use ETH_P_LLDP instead.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Instead of using a local define for the LLDP ethertype, use the kernel
define ETH_P_LLDP.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove references to IXGBE_ETH_P_LLD and use ETH_P_LLDP instead.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove references to I40E_ETH_P_LLDP and use ETH_P_LLDP instead.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add a new define ETH_P_LLDP for Link Layer Discovery Protocol (LLDP)
ethertype.
Suggested-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>