- 05 Nov, 2021 26 commits
-
-
Maxime Ripard authored
The X-Powers AXP PMICs are supported by Linux thanks to its device tree binding. Now that we have the DT validation in place, let's convert the device tree bindings for that driver over to a YAML schema. Signed-off-by:
Maxime Ripard <maxime@cerno.tech> Reviewed-by:
Rob Herring <robh@kernel.org> Acked-by:
Chen-Yu Tsai <wens@csie.org> Signed-off-by:
Lee Jones <lee.jones@linaro.org> Link: https://lore.kernel.org/r/20210924071614.868307-2-maxime@cerno.tech
-
Maxime Ripard authored
The X-Powers AC100 hybrid devices are supported by Linux thanks to its device tree binding. Now that we have the DT validation in place, let's convert the device tree bindings for that driver over to a YAML schema. Signed-off-by:
-
Dmitry Baryshkov authored
PM8xxx PMIC family uses GPIO as parent IRQ. Using it together with the irq_set_chained_handler_and_data() results in warnings from the GPIOLIB (see 461c1a7d ("gpiolib: override irq_enable/disable")) as in this path the IRQ resources are not allocated (and thus the corresponding GPIO is not marked as used for the IRQ. Use request_irq so that the IRQ resources are proprely setup. [ 0.803271] ------------[ cut here ]------------ [ 0.803338] WARNING: CPU: 3 PID: 1 at drivers/gpio/gpiolib.c:3207 gpiochip_enable_irq+0xa4/0xa8 [ 0.803470] Modules linked in: [ 0.803542] CPU: 3 PID: 1 Comm: swapper/0 Not tainted 5.14.0-rc6-next-20210820-postmarketos-qcom-apq8064+ #1 [ 0.803645] Hardware name: Generic DT based system [ 0.803710] Backtrace: [ 0.803777] [<c0e3493c>] (dump_backtrace) from [<c0e34d00>] (show_stack+0x20/0x24) [ 0.803911] r7:00000c87 r6:c07062dc r5:60000093 r4:c11d0f54 [ 0.803980] [<c0e34ce0>] (show_stack) from [<c0e38314>] (dump_stack_lvl+0x48/0x54) [ 0.804097] [<c0e382cc>] (dump_stack_lvl) from [<c0e38338>] (dump_stack+0x18/0x1c) [ 0.804217] r5:00000009 r4:c11fe208 [ 0.804274] [<c0e38320>] (dump_stack) from [<c03219c8>] (__warn+0xfc/0x114) [ 0.804387] [<c03218cc>] (__warn) from [<c0e35334>] (warn_slowpath_fmt+0x74/0xd0) [ 0.804509] r7:c07062dc r6:00000c87 r5:c11fe208 r4:00000000 [ 0.804577] [<c0e352c4>] (warn_slowpath_fmt) from [<c07062dc>] (gpiochip_enable_irq+0xa4/0xa8) [ 0.804716] r8:c27b6200 r7:c27aec00 r6:c27aec18 r5:cf77a448 r4:c02225f0 [ 0.804789] [<c0706238>] (gpiochip_enable_irq) from [<c0706348>] (gpiochip_irq_enable+0x28/0x38) [ 0.804921] r5:cf77a448 r4:c27aec18 [ 0.804977] [<c0706320>] (gpiochip_irq_enable) from [<c03897a0>] (irq_enable+0x48/0x78) [ 0.805111] r5:00000000 r4:c27aec00 [ 0.805167] [<c0389758>] (irq_enable) from [<c0389850>] (__irq_startup+0x80/0xbc) [ 0.805286] r5:00000000 r4:c27aec00 [ 0.805343] [<c03897d0>] (__irq_startup) from [<c038996c>] (irq_startup+0xe0/0x18c) [ 0.805468] r7:c27aec00 r6:00000001 r5:00000000 r4:c27aec00 [ 0.805535] [<c038988c>] (irq_startup) from [<c0389a54>] (irq_activate_and_startup+0x3c/0x74) [ 0.805669] r7:c27aec00 r6:00000001 r5:c27aec00 r4:00000000 [ 0.805736] [<c0389a18>] (irq_activate_and_startup) from [<c0389b58>] (__irq_do_set_handler+0xcc/0x1c0) [ 0.805875] r7:c27aec00 r6:c0383710 r5:c08a16b0 r4:00000001 [ 0.805943] [<c0389a8c>] (__irq_do_set_handler) from [<c0389d80>] (irq_set_chained_handler_and_data+0x60/0x98) [ 0.806087] r7:c27b5c10 r6:c27aed40 r5:c08a16b0 r4:c27aec00 [ 0.806154] [<c0389d20>] (irq_set_chained_handler_and_data) from [<c08a1660>] (pm8xxx_probe+0x1fc/0x24c) [ 0.806298] r6:0000003a r5:0000003a r4:c27b5c00 [ 0.806359] [<c08a1464>] (pm8xxx_probe) from [<c0871420>] (platform_probe+0x6c/0xc8) [ 0.806495] r10:c2507080 r9:e8bea2cc r8:c165e0e0 r7:c165e0e0 r6:c15f08f8 r5:c27b5c10 [ 0.806582] r4:00000000 [ 0.806632] [<c08713b4>] (platform_probe) from [<c086e280>] (really_probe+0xe8/0x460) [ 0.806769] r7:c165e0e0 r6:c15f08f8 r5:00000000 r4:c27b5c10 [ 0.806837] [<c086e198>] (really_probe) from [<c086e6a8>] (__driver_probe_device+0xb0/0x22c) [ 0.806975] r7:c27b5c10 r6:cf70fba4 r5:c15f08f8 r4:c27b5c10 [ 0.807042] [<c086e5f8>] (__driver_probe_device) from [<c086e868>] (driver_probe_device+0x44/0xe0) [ 0.807188] r9:e8bea2cc r8:00000000 r7:c27b5c10 r6:cf70fba4 r5:c16ae4b4 r4:c16ae4b0 [ 0.807271] [<c086e824>] (driver_probe_device) from [<c086ecd8>] (__device_attach_driver+0xb4/0x12c) [ 0.807421] r9:e8bea2cc r8:c15eec08 r7:c27b5c10 r6:cf70fba4 r5:c15f08f8 r4:00000001 [ 0.807506] [<c086ec24>] (__device_attach_driver) from [<c086c06c>] (bus_for_each_drv+0x94/0xe4) [ 0.807651] r7:c16ae484 r6:c086ec24 r5:cf70fba4 r4:00000000 [ 0.807718] [<c086bfd8>] (bus_for_each_drv) from [<c086e0e0>] (__device_attach+0x104/0x19c) [ 0.807852] r6:00000001 r5:c27b5c54 r4:c27b5c10 [ 0.807913] [<c086dfdc>] (__device_attach) from [<c086eef4>] (device_initial_probe+0x1c/0x20) [ 0.808050] r6:c27b5c10 r5:c15ef1b0 r4:c27b5c10 [ 0.808111] [<c086eed8>] (device_initial_probe) from [<c086d00c>] (bus_probe_device+0x94/0x9c) [ 0.808240] [<c086cf78>] (bus_probe_device) from [<c086a60c>] (device_add+0x404/0x8f4) [ 0.808370] r7:c16ae484 r6:c251ba10 r5:00000000 r4:c27b5c10 [ 0.808439] [<c086a208>] (device_add) from [<c0a82f50>] (of_device_add+0x44/0x4c) [ 0.808581] r10:c144c854 r9:00000001 r8:e8bea314 r7:c251ba10 r6:00000000 r5:00000000 [ 0.808669] r4:c27b5c00 [ 0.808718] [<c0a82f0c>] (of_device_add) from [<c0a836cc>] (of_platform_device_create_pdata+0xa0/0xc8) [ 0.808850] [<c0a8362c>] (of_platform_device_create_pdata) from [<c0a83908>] (of_platform_bus_create+0x1f0/0x514) [ 0.809005] r9:00000001 r8:c251ba10 r7:00000000 r6:00000000 r5:00000000 r4:e8bea2b0 [ 0.809086] [<c0a83718>] (of_platform_bus_create) from [<c0a83e04>] (of_platform_populate+0x98/0x128) [ 0.809233] r10:c144c854 r9:00000001 r8:c251ba10 r7:00000000 r6:00000000 r5:e8bea170 [ 0.809321] r4:e8bea2b0 [ 0.809371] [<c0a83d6c>] (of_platform_populate) from [<c0a83f20>] (devm_of_platform_populate+0x60/0xa8) [ 0.809521] r9:0000011d r8:c165e0e0 r7:e8bea170 r6:c2c34f40 r5:c2cac140 r4:c251ba10 [ 0.809604] [<c0a83ec0>] (devm_of_platform_populate) from [<c08a212c>] (ssbi_probe+0x138/0x16c) [ 0.809738] r6:c2c34f40 r5:c251ba10 r4:ff822700 [ 0.809800] [<c08a1ff4>] (ssbi_probe) from [<c0871420>] (platform_probe+0x6c/0xc8) [ 0.809923] r7:c165e0e0 r6:c15f0a80 r5:c251ba10 r4:00000000 [ 0.809989] [<c08713b4>] (platform_probe) from [<c086e280>] (really_probe+0xe8/0x460) [ 0.810120] r7:c165e0e0 r6:c15f0a80 r5:00000000 r4:c251ba10 [ 0.810187] [<c086e198>] (really_probe) from [<c086e6a8>] (__driver_probe_device+0xb0/0x22c) [ 0.810325] r7:c251ba10 r6:c15f0a80 r5:c15f0a80 r4:c251ba10 [ 0.810393] [<c086e5f8>] (__driver_probe_device) from [<c086e868>] (driver_probe_device+0x44/0xe0) [ 0.810539] r9:0000011d r8:00000000 r7:c251ba10 r6:c15f0a80 r5:c16ae4b4 r4:c16ae4b0 [ 0.810623] [<c086e824>] (driver_probe_device) from [<c086ee2c>] (__driver_attach+0xdc/0x188) [ 0.810766] r9:0000011d r8:c144c834 r7:00000000 r6:c15f0a80 r5:c251ba10 r4:00000000 [ 0.810849] [<c086ed50>] (__driver_attach) from [<c086bf60>] (bus_for_each_dev+0x88/0xd4) [ 0.810985] r7:00000000 r6:c086ed50 r5:c15f0a80 r4:00000000 [ 0.811052] [<c086bed8>] (bus_for_each_dev) from [<c086dad4>] (driver_attach+0x2c/0x30) [ 0.811182] r6:c15ef1b0 r5:c2c34e80 r4:c15f0a80 [ 0.811243] [<c086daa8>] (driver_attach) from [<c086d2dc>] (bus_add_driver+0x180/0x21c) [ 0.811364] [<c086d15c>] (bus_add_driver) from [<c086fa6c>] (driver_register+0x84/0x118) [ 0.811492] r7:00000000 r6:ffffe000 r5:c1428210 r4:c15f0a80 [ 0.811558] [<c086f9e8>] (driver_register) from [<c0871174>] (__platform_driver_register+0x2c/0x34) [ 0.811683] r5:c1428210 r4:c16524a0 [ 0.811739] [<c0871148>] (__platform_driver_register) from [<c1428234>] (ssbi_driver_init+0x24/0x28) [ 0.811868] [<c1428210>] (ssbi_driver_init) from [<c0302394>] (do_one_initcall+0x68/0x2c8) [ 0.811990] [<c030232c>] (do_one_initcall) from [<c140147c>] (kernel_init_freeable+0x1dc/0x23c) [ 0.812135] r7:cf7b0400 r6:c130339c r5:00000007 r4:c147f6a0 [ 0.812204] [<c14012a0>] (kernel_init_freeable) from [<c0e40e60>] (kernel_init+0x20/0x138) [ 0.812345] r10:00000000 r9:00000000 r8:00000000 r7:00000000 r6:00000000 r5:c0e40e40 [ 0.812433] r4:00000000 [ 0.812483] [<c0e40e40>] (kernel_init) from [<c0300150>] (ret_from_fork+0x14/0x24) [ 0.812596] Exception stack(0xcf70ffb0 to 0xcf70fff8) [ 0.812684] ffa0: 00000000 00000000 00000000 00000000 [ 0.812809] ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 0.812923] ffe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 0.813008] r5:c0e40e40 r4:00000000 [ 0.813075] ---[ end trace ad2443eee078d094 ]--- Signed-off-by:
Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Tested-by: David Heidelberg <david@ixit.cz> # on Nexus 7 (deb) Signed-off-by:
-
Mark Brown authored
Currently autoloading for SPI devices does not use the DT ID table, it uses SPI modalises. Supporting OF modalises is going to be difficult if not impractical, an attempt was made but has been reverted, so ensure that module autoloading works for this driver by adding a SPI device ID table. Fixes: 96c8395e ("spi: Revert modalias changes") Signed-off-by:
Mark Brown <broonie@kernel.org> Reviewed-by:
Baolin Wang <baolin.wang7@gmail.com> Signed-off-by:
-
Mark Brown authored
Currently autoloading for SPI devices does not use the DT ID table, it uses SPI modalises. Supporting OF modalises is going to be difficult if not impractical, an attempt was made but has been reverted, so ensure that module autoloading works for this driver by adding a SPI device ID table. Fixes: 96c8395e ("spi: Revert modalias changes") Signed-off-by:
-
Mark Brown authored
Currently autoloading for SPI devices does not use the DT ID table, it uses SPI modalises. Supporting OF modalises is going to be difficult if not impractical, an attempt was made but has been reverted, so ensure that module autoloading works for this driver by adding a SPI device ID table. Fixes: 96c8395e ("spi: Revert modalias changes") Signed-off-by:
-
Krzysztof Kozlowski authored
Describe better which driver applies to which SoC, to make configuring kernel for Samsung SoC easier. Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by:
-
Krzysztof Kozlowski authored
Early exits from for_each_child_of_node() should decrement the node reference counter. Reported by Coccinelle: drivers/mfd/mfd-core.c:197:2-24: WARNING: Function "for_each_child_of_node" should have of_node_put() before goto around lines 209. Fixes: c94bb233 ("mfd: Make MFD core code Device Tree and IRQ domain aware") Signed-off-by: -
Orlando Chamberlain authored
Added 8086:38a8 to the intel_lpss_pci driver. It is an Intel Ice Lake PCH-N UART controler present on the MacBookPro16,2. Signed-off-by:
Orlando Chamberlain <redecorating@protonmail.com> Reviewed-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Krzysztof Kozlowski authored
Interrupt line can be configured on different hardware in different way, even inverted. Therefore driver should not enforce specific trigger type - edge falling - but instead rely on Devicetree to configure it. The Maxim 14577/77836 datasheets describe the interrupt line as active low with a requirement of acknowledge from the CPU therefore the edge falling is not correct. The interrupt line is shared between PMIC and charger driver, so using level sensitive interrupt is here especially important to avoid races. With an edge configuration in case if first PMIC signals interrupt followed shortly after by the RTC, the interrupt might not be yet cleared/acked thus the second one would not be noticed. Signed-off-by:
Krzysztof Kozlowski <krzk@kernel.org> Acked-by:
-
Krzysztof Kozlowski authored
Interrupt line can be configured on different hardware in different way, even inverted. Therefore driver should not enforce specific trigger type - edge falling - but instead rely on Devicetree to configure it. The Maxim 77693 datasheet describes the interrupt line as active low with a requirement of acknowledge from the CPU therefore the edge falling is not correct. The interrupt line is shared between PMIC and RTC driver, so using level sensitive interrupt is here especially important to avoid races. With an edge configuration in case if first PMIC signals interrupt followed shortly after by the RTC, the interrupt might not be yet cleared/acked thus the second one would not be noticed. Signed-off-by:
-
Krzysztof Kozlowski authored
Interrupt line can be configured on different hardware in different way, even inverted. Therefore driver should not enforce specific trigger type - edge falling - but instead rely on Devicetree to configure it. The Maxim 77686 datasheet describes the interrupt line as active low with a requirement of acknowledge from the CPU therefore the edge falling is not correct. The interrupt line is shared between PMIC and RTC driver, so using level sensitive interrupt is here especially important to avoid races. With an edge configuration in case if first PMIC signals interrupt followed shortly after by the RTC, the interrupt might not be yet cleared/acked thus the second one would not be noticed. Signed-off-by:
-
Krzysztof Kozlowski authored
Interrupt line can be configured on different hardware in different way, even inverted. Therefore driver should not enforce specific trigger type - edge falling - but instead rely on Devicetree to configure it. The Samsung PMIC drivers are used only on Devicetree boards. Additionally, the PMIC datasheets describe the interrupt line as active low with a requirement of acknowledge from the CPU therefore the edge falling is not correct. Marek Szyprowski reports that together with DTS change (proper level in DTS) it fixes RTC alarm failure that he observed from time to time on TM2e board. Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
-
Paul Kocialkowski authored
The LogiCVC multi-function device has a display part which is now described in its binding. Add a patternProperties match for it. Signed-off-by:
Paul Kocialkowski <paul.kocialkowski@bootlin.com> Acked-by:
-
Krzysztof Kozlowski authored
The MODULE_DEVICE_TABLE already creates proper alias. Having another MODULE_ALIAS causes the alias to be duplicated: $ modinfo cros_ec_dev.ko alias: platform:cros-ec-dev srcversion: F84A69D2156719A4F717A76 alias: platform:cros-ec-dev Signed-off-by:
-
Ramona Alexandra Nechita authored
The description mentioned AD5520, which is a different device. Fixed the typo. Signed-off-by:
Ramona Alexandra Nechita <ramona.nechita@analog.com> Signed-off-by:
-
Chunyan Zhang authored
SC2730 is a PMIC SoC integrated in UMS512. Signed-off-by:
Chunyan Zhang <chunyan.zhang@unisoc.com> Signed-off-by:
-
Baruch Siach authored
Signed-off-by:
Baruch Siach <baruch@tkos.co.il> Signed-off-by:
-
Carlos de Paula authored
This update adds new regmap to support the latest EA silicon which will be selected based on the chip and variant information read from the device. Signed-off-by:
Carlos de Paula <me@carlosedp.com> Reviewed-by:
Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by:
-
Ondrej Jirman authored
RK817 has a power-off bit in SYS_CFG3. Add support for powering off the PMIC. Signed-off-by:
Ondrej Jirman <megous@megous.com> Signed-off-by:
-
Prarit Bhargava authored
The intel_pmt driver shows up as a compile option for all arches but is 32-bit and 64-bit x86 specific. Add a CONFIG dependency on X86 for intel_pmt. Signed-off-by:
Prarit Bhargava <prarit@redhat.com> Reviewed-by:
David E. Box <david.e.box@linux.intel.com> Reviewed-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Colin Ian King authored
There is a spelling mistake in a dev_err message. Fix it. Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Rafał Miłecki authored
Northstar's USB 2.0 PHY is part of the CRU MFD. Signed-off-by:
Rafał Miłecki <rafal@milecki.pl> Reviewed-by:
-
Rafał Miłecki authored
CRU has a shared register that is used e.g. to control USB 2.0 PHY block access. It's a single 32 b register. Document it as syscon so it can be used with a regmap. Signed-off-by:
-
Rafał Miłecki authored
Broadcom's MISC is an MFD hardware block used on some of their SoCs like bcm63xx and bcm4908. At this point only PCIe reset is fully understood and documented. More functions may be added later. Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Reviewed-by:
-
Lee Jones authored
Merge branches 'ib-mfd-iio-touchscreen-clk-5.16', 'ib-mfd-misc-regulator-5.16' and 'tb-mfd-from-regulator-5.16' into ibs-for-mfd-merged
-
- 21 Oct, 2021 14 commits
-
-
Krzysztof Kozlowski authored
Document the properties with regulator supplies for bucks and LDOs. At least one board uses it (Exynos5250 Arndale). Signed-off-by:
-
Krzysztof Kozlowski authored
Convert the MFD part of Samsung S5M8767 PMIC to DT schema format. Previously the bindings were mostly in mfd/samsung,sec-core.txt. Since all of bindings for Samsung S2M and S5M family of PMICs were converted from mfd/samsung,sec-core.txt to respective dtschema file, remove the former one. Signed-off-by:
-
Krzysztof Kozlowski authored
Convert the MFD part of Samsung S2MPA01 PMIC to DT schema format. Previously the bindings were mostly in mfd/samsung,sec-core.txt. Signed-off-by:
-
Krzysztof Kozlowski authored
Convert the MFD part of Samsung S2MPS11/S2MPS13/S2MPS14/S2MPS15/S2MPU02 family of PMICs to DT schema format. Previously the bindings were mostly in mfd/samsung,sec-core.txt. The conversion copies parts of description from existing bindings therefore the license is not changed from GPLv2. Signed-off-by:
-
Lee Jones authored
regulator/clock: Convert the s2m and s5m DT bindings to schema Tagged to allow further bindings to rely on these. Signed-off-by: -
Miquel Raynal authored
This driver supports both the legacy controller (am33xx) and the extended one (am437x), so let's add a new compatible. Signed-off-by:
Miquel Raynal <miquel.raynal@bootlin.com> Acked-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by:
-
Miquel Raynal authored
Without the scale, the values returned to the user are just a picture of the input voltage against the full scale range of the ADC. We need to provide the actual conversion factor to get milli-Volts values. Signed-off-by:
-
Miquel Raynal authored
The lack of unit in the macro name kind of tricked me when I was troubleshooting an issue. Physical constants should always get a unit. Signed-off-by:
-
Miquel Raynal authored
Move the checks over the delays provided in the device tree to the location where these values are read to clarify where they come from. There are no functional changes besides the device structure used to display the warnings: let's use the ADC instead of the MFD device. Signed-off-by:
-
Miquel Raynal authored
Gotos jumping to a return statement are not really useful, drop them. Signed-off-by:
-
Miquel Raynal authored
These warnings are reported by checkpatch.pl essentially. Signed-off-by:
-
Miquel Raynal authored
Drop the text license and replace it with an equivalent SPDX license tag identifier which also matches the MODULE_LICENSE("GPL"). Signed-off-by: -
Miquel Raynal authored
At least on a am4372, a simple: $ cat /sys/bus/iio/devices/iio\:deviceX/in_voltage*_raw can stall forever. It seems that it comes from the fact that the internal state machine does not have enough time to return to its idle state in this situation before receiving another request, leading to an internal stall. Add a tiadc_wait_idle() helper to ensure no new conversion is requested while the FSM is still busy. Signed-off-by:
-
Miquel Raynal authored
There was in the past a typo in the coordinate readouts property. The bindings have been updated, the touchscreen driver as well and now supports both. However, the MFD driver that is in charge of verifying the validity of the property only checks the bogus one. Add support for the correctly spelled DT property. Fixes: c9aeb249 ("Input: ti_am335x_tsc - fix spelling mistake in TSC/ADC DT binding") Signed-off-by:
-
