- 23 Apr, 2020 3 commits
-
-
Alexey Minnekhanov authored
This adds the initial device tree support for Xiaomi Redmi Note 7 (codename lavender) phone. It is based on SDM660 SoC. Currently it can be booted into initrd with a shell over UART and you can also get kernel boot logs from a pstore-ramoops. Signed-off-by:
Alexey Minnekhanov <alexey.min@gmail.com> Link: https://lore.kernel.org/r/20200417012630.222352-4-alexey.min@gmail.comSigned-off-by:
Bjorn Andersson <bjorn.andersson@linaro.org>
-
Craig Tatlor authored
Initial device tree support for Qualcomm SDM660 SoC. SDM660 is based off MSM8998 and uses some of its drivers. SDM630/636 are based off SDM660 SoC and they are pin and software compatible. The device tree is based on the CAF 4.4 kernel tree. Features: * CPU nodes * Timer nodes * Interrupt controller * Global Clock Controller * Top Level Mode Multiplexer (pin controller) * UART node This is inspired by and based on the work of Craig Tatlor in https://patchwork.kernel.org/patch/10563667/Signed-off-by:
Craig Tatlor <ctatlor97@gmail.com> Signed-off-by:
-
Alexey Minnekhanov authored
Add a SoC strings for the Qualcomm SDM630 and SDM660 SoCs. Also document the new xiaomi,lavender compatible used in a device tree binding. Signed-off-by:
-
- 21 Apr, 2020 5 commits
-
-
Bjorn Andersson authored
The pdc node suffers from both too narrow compatible and insufficient cells in the reg, fix these. Fixes: 60378f1a ("arm64: dts: qcom: sm8250: Add sm8250 dts file") Tested-by:
Vinod Koul <vkoul@kernel.org> Reviewed-by:
-
Bryan O'Donoghue authored
Add nodes for the UFS controller and PHY, and enable these for the MTP with relevant supplies specified. Tested-by:
Bryan O'Donoghue <bryan.odonoghue@linaro.org> Link: https://lore.kernel.org/r/20200415061430.740854-3-bjorn.andersson@linaro.orgSigned-off-by:
-
Bryan O'Donoghue authored
Add RPMh controlled regulators for the three PMICs and specify voltage ranges and mode for relevant regulators. Tested-by:
-
Bjorn Andersson authored
Tested-by:
-
Sai Prakash Ranjan authored
Add coresight components found on Qualcomm SC7180 SoC. Signed-off-by:
Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org> Reviewed-by:
Stephen Boyd <swboyd@chromium.org> Reviewed-by:
Mathieu Poirier <mathieu.poirier@linaro.org> Tested-by:
-
- 20 Apr, 2020 1 commit
-
-
Jonathan Marek authored
This was mistakenly copied from the downstream dts, however the upstream driver works differently. I only tested this with the pm8150_gpios node (used with volume button), but the 2 others should be the same. Fixes: e92b61c8 ("arm64: dts: qcom: pm8150l: Add base dts file") Fixes: 229d5bca ("arm64: dts: qcom: pm8150b: Add base dts file") Fixes: 5101f22a ("arm64: dts: qcom: pm8150: Add base dts file") Reviewed-by:
Jonathan Marek <jonathan@marek.ca> Link: https://lore.kernel.org/r/20200420153543.14512-1-jonathan@marek.caSigned-off-by:
-
- 14 Apr, 2020 28 commits
-
-
Sandeep Maheswaram authored
Overriding the QUSB2 V2 Phy tuning parameters for SC7180 IDP device. Signed-off-by:
Sandeep Maheswaram <sanm@codeaurora.org> Reviewed-by:
-
Sandeep Maheswaram authored
Use generic QUSB2 V2 Phy configuration for SC7180. Signed-off-by:
Matthias Kaehlcke <mka@chromium.org> Reviewed-by:
-
Sandeep Maheswaram authored
Use generic QUSB2 V2 Phy configuration for sdm845. Signed-off-by:
-
Maulik Shah authored
Add device bindings for cpuidle states for cpu devices. Cc: devicetree@vger.kernel.orgi Signed-off-by:
Maulik Shah <mkshah@codeaurora.org> Reviewed-by:
Srinivas Rao L <lsrao@codeaurora.org> Reviewed-by:
-
Sivaprakash Murugesan authored
This patch re-arranges ipq8074 device nodes based on node address followed by node names followed by node labels. Suggested-by:
Sivaprakash Murugesan <sivaprak@codeaurora.org> Link: https://lore.kernel.org/r/1586572830-22727-1-git-send-email-sivaprak@codeaurora.orgSigned-off-by:
-
Matthias Kaehlcke authored
Add the interconnect path configuration for the venus video codec of the SC7180. Signed-off-by:
-
Rajeshwari authored
Changed polling-delay and polling-delay-passive to zero to disable polling mode of the framework as interrupts for tsens are already configured. Signed-off-by:
Rajeshwari <rkambl@codeaurora.org> Reviewed-by:
Amit Kucheria <amit.kucheria@linaro.org> Reviewed-by:
Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/1586244677-14399-1-git-send-email-rkambl@codeaurora.orgSigned-off-by:
-
Douglas Anderson authored
Devices are supposed to be sorted by unit address. These two got swapped when they landed. Fix. Reviewed-by:
-
Amit Kucheria authored
The thermal trip points have unit name but no reg property, so we can remove them. It also fixes the following warnings from 'make dtbs_check' after adding the thermal yaml bindings. arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones: cpu0-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones: cpu1-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones: cpu2-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones: cpu3-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones: cpu4-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones: cpu5-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones: cpu6-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones: cpu7-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones: clust0-mhm-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones: clust1-mhm-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones: cluster1-l2-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones: modem-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones: mem-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones: wlan-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones: q6-dsp-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones: camera-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones: multimedia-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones: cpu0-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones: cpu1-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones: cpu2-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones: cpu3-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones: cpu4-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones: cpu5-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones: cpu6-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones: cpu7-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones: clust0-mhm-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones: clust1-mhm-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones: cluster1-l2-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones: modem-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones: mem-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones: wlan-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones: q6-dsp-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones: camera-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones: multimedia-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' Signed-off-by: -
Amit Kucheria authored
The thermal trip points have unit name but no reg property, so we can remove them. It also fixes the following warnings from 'make dtbs_check' after adding the thermal yaml bindings. arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones: cpu0-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones: cpu1-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones: cpu2-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones: cpu3-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones: m4m-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones: l3-or-venus-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones: cluster0-l2-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones: cluster1-l2-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones: camera-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones: q6-dsp-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones: mem-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones: modemtx-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones: cpu0-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones: cpu1-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones: cpu2-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones: cpu3-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones: m4m-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones: l3-or-venus-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones: cluster0-l2-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones: cluster1-l2-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones: camera-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones: q6-dsp-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones: mem-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones: modemtx-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' Signed-off-by: -
Amit Kucheria authored
The thermal trip points have unit name but no reg property, so we can remove them. It also fixes the following warnings from 'make dtbs_check' after adding the thermal yaml bindings. arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: thermal-zones: gpu-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: thermal-zones: camera-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: thermal-zones: modem-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml: thermal-zones: gpu-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml: thermal-zones: camera-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml: thermal-zones: modem-thermal:trips: 'trip-point@0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' Signed-off-by: -
Krishna Manikandan authored
Add DISP_CC_MDSS_ROT_CLK and DISP_CC_MDSS_AHB_CLK in the assigned clocks list as these are display specific clocks and needs to be initialized from the client side. Adding the default rate of 19.2 mhz for these clocks for sc7180 target. Signed-off-by:
Krishna Manikandan <mkrishn@codeaurora.org> Link: https://lore.kernel.org/r/1584709864-5587-1-git-send-email-mkrishn@codeaurora.orgSigned-off-by:
-
Evan Green authored
Re-introduce the include of the sc7180 interconnect node name definitions. Though this was part of v5 of the interconnect provider series [1], it was dropped because the DT changes went through a different tree than the header. Re-add that now. Interconnect clients being introduced can reference this patch as a dependency, rather than racing each other to add the include. [1] https://patchwork.kernel.org/patch/11417989/Signed-off-by:
Evan Green <evgreen@chromium.org> Link: https://lore.kernel.org/r/20200310161502.1.Ia2884ed3c8826f52fbd5dcfa7a376a2fac4f31e6@changeidSigned-off-by:
-
Robert Foss authored
Enable the ov8856 main camera and the ov7251 b/w tracking camera used on the Qualcomm RB3 kit. Currently the camera nodes have not yet been attached to an to a CSI2 endpoint, since no driver currently supports the ISP that the the SDM845/db845c ships with. Signed-off-by:
Robert Foss <robert.foss@linaro.org> Reviewed-by:
-
Robert Foss authored
Add pm_8998 GPIO trace names. These names are defined in the 96boards db845c mezzanine schematic. Signed-off-by:
-
Robert Foss authored
The sdm845 SOC ships with a CCI controller, which has two CCI/I2C buses. Signed-off-by:
-
Loic Poulain authored
Add cci device to msm8916.dtsi. Add default 96boards camera node for db410c (apq8016-sbc). Signed-off-by:
Loic Poulain <loic.poulain@linaro.org> Signed-off-by:
-
Loic Poulain authored
The msm8916 CCI controller provides one CCI/I2C bus. Signed-off-by:
-
Bryan O'Donoghue authored
This patch enables the primary and secondary USB controllers on the qcs404-evb. Primary: The primary USB controller has - One USB3 SS PHY using gpio-usb-conn - One USB2 HS PHY in device mode only and no connector driver associated. Secondary: The second DWC3 controller which has one USB Hi-Speed PHY attached to it. Cc: Andy Gross <agross@kernel.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Rob Herring <robh+dt@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: linux-arm-msm@vger.kernel.org Cc: devicetree@vger.kernel.org Cc: linux-kernel@vger.kernel.org Tested-by:
-
Bryan O'Donoghue authored
Rather than set the minimum microvolt for this regulator in the USB SS PHY driver, set it in the DTS. Suggested-by:
-
Bryan O'Donoghue authored
VBUS is supplied by an external regulator controlled by a GPIO pin. This patch models the regulator as regulator-usb3-vbus. Cc: Andy Gross <agross@kernel.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Rob Herring <robh+dt@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: linux-arm-msm@vger.kernel.org Cc: devicetree@vger.kernel.org Cc: linux-kernel@vger.kernel.org Tested-by:
-
Bryan O'Donoghue authored
The USB ID pin is used to tell if a system is a Host or a Device. For our purposes we will bind this pin into gpio-usb-conn later. For now define the pin with its pinmux. Cc: Andy Gross <agross@kernel.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Rob Herring <robh+dt@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: linux-arm-msm@vger.kernel.org Cc: devicetree@vger.kernel.org Cc: linux-kernel@vger.kernel.org Tested-by:
-
Bryan O'Donoghue authored
Defines VBUS detect and VBUS boost for the QCS404 EVB. Detect: VBUS present/absent is presented to the SoC via a GPIO on the EVB. Define the pin mapping for later use by gpio-usb-conn. Boost: An external regulator is used to trigger VBUS on/off via GPIO. This patch defines the relevant GPIO in the EVB dts. Cc: Andy Gross <agross@kernel.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Rob Herring <robh+dt@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: linux-arm-msm@vger.kernel.org Cc: devicetree@vger.kernel.org Cc: linux-kernel@vger.kernel.org Tested-by:
-
Bjorn Andersson authored
QCS404 sports HS and SS USB controllers based on dwc3 block with two HS PHYs and one SS PHY. Add nodes for these devices and enable them for EVB board. Signed-off-by:
Shawn Guo <shawn.guo@linaro.org> Cc: Andy Gross <agross@kernel.org> Cc: Rob Herring <robh+dt@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: linux-arm-msm@vger.kernel.org Cc: devicetree@vger.kernel.org Cc: linux-kernel@vger.kernel.org Tested-by:
-
Amit Kucheria authored
"arm,armv8" compatible should only be used for software models. Replace it with the real cpu type. Reviewed-by:
Rajendra Nayak <rnayak@codeaurora.org> Signed-off-by:
-
Amit Kucheria authored
Kryo468 is found in sc7180, so add it to the list of cpu compatibles Reviewed-by:
-
Ulf Hansson authored
Subnodes for PSCI should start with "power-domain-", so let's adopt to this. Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Link: https://lore.kernel.org/r/20200326103932.5809-3-ulf.hansson@linaro.orgSigned-off-by:
-
Ulf Hansson authored
As the domain-idle-state DT binding got converted to the json-schema, a few minor changes were introduced. For example, the states needs to be specified within a separate node, named domain-idle-states. Let's conform to the updated binding. This also silence the below errors for msm8916 from of 'make dtbs_check': idle-states: cluster-retention:compatible:0: 'arm,idle-state' was expected idle-states: cluster-gdhs:compatible:0: 'arm,idle-state' was expected Signed-off-by:
-
- 12 Apr, 2020 3 commits
-
-
Linus Torvalds authored
-
Linus Torvalds authored
This sorts the actual field names too, potentially causing even more chaos and confusion at merge time if you have edited the MAINTAINERS file. But the end result is a more consistent layout, and hopefully it's a one-time pain minimized by doing this just before the -rc1 release. This was entirely scripted: ./scripts/parse-maintainers.pl --input=MAINTAINERS --output=MAINTAINERS --order Requested-by:
Joe Perches <joe@perches.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Linus Torvalds authored
They are all supposed to be sorted, but people who add new entries don't always know the alphabet. Plus sometimes the entry names get edited, and people don't then re-order the entry. Let's see how painful this will be for merging purposes (the MAINTAINERS file is often edited in various different trees), but Joe claims there's relatively few patches in -next that touch this, and doing it just before -rc1 is likely the best time. Fingers crossed. This was scripted with /scripts/parse-maintainers.pl --input=MAINTAINERS --output=MAINTAINERS but then I also ended up manually upper-casing a few entry names that stood out when looking at the end result. Requested-by:
-
