Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Vincent Penquerc'h <vincent.penquerch@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Change 130f315a (staging: zram: remove special handle of uncompressed page)
introduced a bug in the handling of incompressible pages which resulted in
memory allocation failure for such pages.

When a page expands on compression, say from 4K to 4K+30, we were trying to
do zsmalloc(pool, 4K+30). However, the maximum size which zsmalloc can
allocate is PAGE_SIZE (for obvious reasons), so such allocation requests
always return failure (0).

For a page that has compressed size larger than the original size (this may
happen with already compressed or random data), there is no point storing
the compressed version as that would take more space and would also require
time for decompression when needed again. So, the fix is to store any page,
whose compressed size exceeds a threshold (max_zpage_size), as-it-is i.e.
without compression.  Memory required for storing this uncompressed page can
then be requested from zsmalloc which supports PAGE_SIZE sized allocations.

Lastly, the fix checks that we do not attempt to "decompress" the page which
we stored in the uncompressed form -- we just memcpy() out such pages.
Signed-off-by: Nitin Gupta <ngupta@vflare.org>
Reported-by: viechweg@gmail.com
Reported-by: paerley@gmail.com
Reported-by: wu.tommy@gmail.com
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The default kernel mapping for the pages allocated for the binder
buffers is never used. Set the __GFP_HIGHMEM flag when allocating
these pages so we don't needlessly use low memory pages that may
be required elsewhere.
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If a thread or process exited while a reply, one-way transaction or
death notification was pending, the struct holding the pending work
was leaked.
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

`labpc_common_detach()` is called by the comedi core to clean up if
either `labpc_attach()` (including the one in the "ni_labpc_cs" module)
or `labpc_attach_pci()` returns an error.  It assumes the `thisboard`
macro (expanding to `((struct labpc_board_struct *)dev->board_ptr)`) is
non-null.  This is a valid assumption if `labpc_attach()` fails, but not
if `labpc_attach_pci()` fails, leading to a possible NULL pointer
dereference.

Check `thisboard` at the top of `labpc_common_detach()` and return early
if it is `NULL`.  This is okay because the only other thing that could
have been allocated is `dev->private` and that is freed by the comedi
core, not by this function.

Cc: <stable@vger.kernel.org> # 3.6.x
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

`das08_detach()` is called by the comedi core to clean up if either
`das08_attach()` or `das08_attach_pci()` returns an error.  It sets
`thisboard` to the return value of `comedi_board(dev)` and assumes it is
non-null.  This is a valid assumption if `das08_attach()` fails, but not
if `das08_attach_pci()` fails, leading to a possible NULL pointer
dereference.

Check `thisboard` at the top of `das08_detach()` and return early if it
is `NULL`.  This is okay because the only other thing that could have
been allocated is `dev->private` and that is freed by the comedi core,
not by this function.

Cc: <stable@vger.kernel.org> # 3.6.x
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

`pc263_detach()` is called by the comedi core to clean up if either
`pc263_attach()` or `pc263_attach_pci()` returns an error.  It sets
`thisboard` to the return value of `comedi_board(dev)` and assumes it is
non-null.  This is a valid assumption if `pc263_attach()` fails, but not
if `pc263_attach_pci()` fails, leading to a possible NULL pointer
dereference.

Check `thisboard` at the top of `pc263_detach()` and return early if it
is `NULL`.  This is okay because no other resources need cleaning up in
this case.

Cc: <stable@vger.kernel.org> # 3.6.x
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

`pc236_detach()` is called by the comedi core to clean up if either
`pc236_attach()` or `pc236_attach_pci()` returns an error.  It sets
`thisboard` to the return value of `comedi_board(dev)` and assumes it is
non-null.  This is a valid assumption if `pc236_attach()` fails, but not
if `pc236_attach_pci()` fails, leading to a possible NULL pointer
dereference.

Check `thisboard` at the top of `pc236_detach()` and return early if it
is `NULL`.  This is okay because the only other thing that could have
been allocated is `dev->private` and that is freed by the comedi core,
not by this function.

Cc: <stable@vger.kernel.org> # 3.6.x
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

`pc236_detach()` is called by the comedi core if it attempted to attach
a device and failed.  `pc236_detach()` calls `pc236_intr_disable()` if
the comedi device private data pointer (`devpriv`) is non-null.  This
test is insufficient as `pc236_intr_disable()` accesses hardware
registers and the attach routine may have failed before it has saved
their I/O base addresses.

Fix it by checking `dev->iobase` is non-zero before calling
`pc236_intr_disable()` as that means the I/O base addresses have been
saved and the hardware registers can be accessed.  It also implies the
comedi device private data pointer is valid, so there is no need to
check it.

Cc: <stable@vger.kernel.org> # 3.5.x, 3.6.x
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

`dio200_detach()` is called by the comedi core to clean up if either
`dio200_attach()` or `dio200_attach_pci()` return an error.  It assigns
`thisboard` to the return value of `comedi_board(dev)` and assumes it is
non-null.  In the case of a previous call to `dio200_attach()` it won't
be `NULL` because the comedi core will have pointed it to one of the
elements of `dio200_boards[]`, but in the case of a previous call to
`dio200_attach_pci()` it could be `NULL`, leading to a null pointer
dereference.

Check that `thisboard` is valid at the top of `dio200_detach()` and
return early if it is `NULL`.  This is okay because the only other thing
that could have been allocated is `dev->private` and that is freed by
the comedi core, not by this function.

Cc: <stable@vger.kernel.org> # 3.6.x
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

`pci_8255_detach()` will be called by the comedi core if
`pci_8255_attach_pci()` returns an error.  It currently assumes that
both `board` (assigned from the return value of `comedi_board(dev)`) and
`devpriv` (assigned from `dev->private`) are non-null, but they might
be null, leading to a null pointer dereference.

`pci_8255_detach()` doesn't need to do anything if either `board` or
`devpriv` are null, so just return early in this case.

Cc: <stable@vger.kernel.org> # 3.6.x
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Here is a small patch to fix a problem caused by a previous patch that
removed the  callback function.  The callback remove patch:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=1de02225358988e8fd48d1dc3fd12336bbae258a

I finally booted my dev machine on the latest kernel (running Debian
here so it's still on 3.2 normally) to test the ni_daq_700 driver with
my test program and noticed this bug.

Shift the DIO_R read result to bits 8..15 Digital direction
configuration: channels 0-7 output, 8-15 input (8225 device emu as port
A output, port B input, port C N/A).

Cc: <stable@vger.kernel.org> # 3.6.x
Signed-off-by: Fred Brooks <nsaspook@nsaspook.com>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'iio-fixes-for-3.7a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus

First round of fixes for IIO in 3.7 cycle, applies to 3.7-rc1.

Mostly a round of fixes for Analog Devices MEMs devices where some
offset values were either completely incorrect, or in the wrong units.

Also removal of an accidental duplicate entry in a Kconfig file.

Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The temperature channel has a calibbias attribute which it should not have, but
the offset attribute is missing.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Temperature scale and offset differ between the different devices supported by
this driver. Right now the driver always reports the temperature scale and
offset of the adis16400 regardless of which chip variant is used. This patch
adds two new attributes to the chip_info struct, one for the temperature scale
and one for the temperature offset.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Most of the channel offsets and scales in the adis16400 are incorrect:
    * Voltage scale is off by a factor of 1000
    * Temperature scale is off by a factor of 1000
	* Temperature offset is completely wrong
	* Some of the acceleration scales are either completely wrong or have the
	  wrong unit
	* Some of the angular velocity scale are either completely wrong or have
	  the wrong unit

This patch fixes these issues. For consistency it also converts scales which are
correct to use the IIO_G_TO_M_S_2 and IIO_DEGREE_TO_RAD macro. This makes it
much easier to compare it to the value given in the datasheet.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Most of the channel offsets and scales in the adis16260 are incorrect:
	* Temperature scale is off by a factor of 1000
	* Voltage scale is off by a factor of 1000
	* Temperature offset is completely wrong

This patch fixes these issues. Also use the IIO_DEGREE_TO_RAD for the angle
velocity since this makes it much easier to compare it to the value given in the
datasheet.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Most of the channel offsets and scales in the adis16240 are incorrect:
    * Temperature scale is of by a factor of 1000
    * Voltage scale is of by a factor of 1000
    * Temperature offset is completely wrong
	* Peak scale is completely wrong

This patch fixes these issues. Also use the IIO_G_TO_M_S_2 macro for the
acceleration scale since this makes it much easier to compare it to the value
given in the datasheet.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Most of the channel offsets and scales in the adis16220 are incorrect:
	* Temperature scale is off by a factor of 1000
	* Voltage scale is off by a factor of 1000
	* Acceleration seems to have a typo "187042" since it should be instead of
	  "1887042"
	* Temperature offset is completely wrong

This patch fixes these issues.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Most of the channel offsets and scales in the adis16209 are incorrect:
	* Temperature scale is of by a factor of 1000
	* Voltage scale is of by a factor of 1000
	* Temperature offset is completely wrong
	* Rotational position scale is missing

This patch fixes these issues. Also use the IIO_G_TO_M_S_2 macro for the
acceleration scale since this makes it much easier to compare it with the value
given in the datasheet.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Most of the channel offsets and scales in the adis16204 are incorrect:
	* Temperature scale is off by a factor of 1000
	* Voltage scale is off by a factor of 1000
	* Acceleration is scale is in g instead of m/(s**2)
	* Temperature offset is completely wrong

This patch fixes these issues.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Most of the channel offsets and scales in the adis16203 are incorrect:
	* Temperature scale is off by a factor of 1000
	* Voltage scale is off by a factor of 1000
	* Temperature offset is completely wrong

This patch fixes these issues.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Most of the channel offsets and scales in the adis16201 are incorrect:
	* Temperature scale is off by a factor of 1000
	* Voltage scale is off by a factor of 1000
	* Acceleration scale is in g instead of m/(s**2)
	* Temperature offset is completely wrong

This patch fixes these issues.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Some datasheets use a different unit to specify the channel scale than what IIO
expects it to be. This patch adds two helper macros which allow to convert units
commonly used in datasheets to IIO units:

 * acceleration: g -> meter / second**2
 * angular velocity: degree (/ second) -> rad (/ second)

This makes it much more convenient to specify and also easier to verify a
channel's scale attribute.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Pull MIPS update from Ralf Baechle:
 "Cleanups and fixes for breakage that occured earlier during this merge
  phase.  Also a few patches that didn't make the first pull request.
  Of those is the Alchemy work that merges code for many of the SOCs and
  evaluation boards thus among other code shrinkage, reduces the number
  of MIPS defconfigs by 5."

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (22 commits)
  MIPS: SNI: Switch RM400 serial to SCCNXP driver
  MIPS: Remove unused empty_bad_pmd_table[] declaration.
  MIPS: MT: Remove kspd.
  MIPS: Malta: Fix section mismatch.
  MIPS: asm-offset.c: Delete unused irq_cpustat_t struct offsets.
  MIPS: Alchemy: Merge PB1100/1500 support into DB1000 code.
  MIPS: Alchemy: merge PB1550 support into DB1550 code
  MIPS: Alchemy: Single kernel for DB1200/1300/1550
  MIPS: Optimize TLB refill for RI/XI configurations.
  MIPS: proc: Cleanup printing of ASEs.
  MIPS: Hardwire detection of DSP ASE Rev 2 for systems, as required.
  MIPS: Add detection of DSP ASE Revision 2.
  MIPS: Optimize pgd_init and pmd_init
  MIPS: perf: Add perf functionality for BMIPS5000
  MIPS: perf: Split the Kconfig option CONFIG_MIPS_MT_SMP
  MIPS: perf: Remove unnecessary #ifdef
  MIPS: perf: Add cpu feature bit for PCI (performance counter interrupt)
  MIPS: perf: Change the "mips_perf_event" table unsupported indicator.
  MIPS: Align swapper_pg_dir to 64K for better TLB Refill code.
  vmlinux.lds.h: Allow architectures to add sections to the front of .bss
  ...

Pull module signing support from Rusty Russell:
 "module signing is the highlight, but it's an all-over David Howells frenzy..."

Hmm "Magrathea: Glacier signing key". Somebody has been reading too much HHGTTG.

* 'modules-next' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (37 commits)
  X.509: Fix indefinite length element skip error handling
  X.509: Convert some printk calls to pr_devel
  asymmetric keys: fix printk format warning
  MODSIGN: Fix 32-bit overflow in X.509 certificate validity date checking
  MODSIGN: Make mrproper should remove generated files.
  MODSIGN: Use utf8 strings in signer's name in autogenerated X.509 certs
  MODSIGN: Use the same digest for the autogen key sig as for the module sig
  MODSIGN: Sign modules during the build process
  MODSIGN: Provide a script for generating a key ID from an X.509 cert
  MODSIGN: Implement module signature checking
  MODSIGN: Provide module signing public keys to the kernel
  MODSIGN: Automatically generate module signing keys if missing
  MODSIGN: Provide Kconfig options
  MODSIGN: Provide gitignore and make clean rules for extra files
  MODSIGN: Add FIPS policy
  module: signature checking hook
  X.509: Add a crypto key parser for binary (DER) X.509 certificates
  MPILIB: Provide a function to read raw data into an MPI
  X.509: Add an ASN.1 decoder
  X.509: Add simple ASN.1 grammar compiler
  ...

The hostprogs need access to the CONFIG_* symbols found in
include/generated/autoconf.h.  But commit abbf1590 ("UAPI: Partition
the header include path sets and add uapi/ header directories") replaced
$(LINUXINCLUDE) with $(USERINCLUDE) which doesn't contain the necessary
include paths.

This has the undesirable effect of breaking the EFI boot stub because
the #ifdef CONFIG_EFI_STUB code in arch/x86/boot/tools/build.c is
never compiled.

It should also be noted that because $(USERINCLUDE) isn't exported by
the top-level Makefile it's actually empty in arch/x86/boot/Makefile.

Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The UAPI commits forgot to test tooling builds such as tools/perf/,
and this fixes the fallout.

Manual conversion.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ARM update from Russell King:
 "This is the final round of stuff for ARM, left until the end of the
  merge window to reduce the number of conflicts.  This set contains the
  ARM part of David Howells UAPI changes, and a fix to the ordering of
  'select' statements in ARM Kconfig files (see the appropriate commit
  for why this happened - thanks to Andrew Morton for pointing out the
  problem.)

  I've left this as long as I dare for this window to avoid conflicts,
  and I regenerated the config patch yesterday, posting it to our
  mailing list for review and testing.  I have several acks which
  include successful test reports for it.

  However, today I notice we've got new conflicts with previously unseen
  code...  though that conflict should be trivial (it's my changes vs a
  one liner.)"

* 'late-for-linus' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: config: make sure that platforms are ordered by option string
  ARM: config: sort select statements alphanumerically
  UAPI: (Scripted) Disintegrate arch/arm/include/asm

Fix up fairly conflict in arch/arm/Kconfig (the select re-organization
vs recent addition of GENERIC_KERNEL_EXECVE)

Pull UAPI disintegration for include/linux/{,byteorder/}*.h from David Howells:
 "The patches contained herein do the following:

 (1) Remove kernel-only stuff in linux/ppp-comp.h from the UAPI.  I checked
     this with Paul Mackerras before I created the patch and he suggested some
     extra bits to unexport.

 (2) Remove linux/blk_types.h entirely from the UAPI as none of it is userspace
     applicable, and remove from the UAPI that part of linux/fs.h that was the
     reason for linux/blk_types.h being exported in the first place.  I
     discussed this with Jens Axboe before creating the patch.

 (3) The big patch of the series to disintegrate include/linux/*.h as a unit.
     This could be split up, though there would be collisions in moving stuff
     between the two Kbuild files when the parts are merged as that file is
     sorted alphabetically rather than being grouped by subsystem.

     Of this set of headers, 17 files have changed in the UAPI exported region
     since the 4th and only 8 since the 9th so there isn't much change in this
     area - as one might expect.

     It should be pretty obvious and straightforward if it does come to fixing
     up: stuff in __KERNEL__ guards stays where it is and stuff outside moves
     to the same file in the include/uapi/linux/ directory.

     If a new file appears then things get a bit more complicated as the
     "headers +=" line has to move to include/uapi/linux/Kbuild.  Only one new
     file has appeared since the 9th and I judge this type of event relatively
     unlikely.

 (4) A patch to disintegrate include/linux/byteorder/*.h as a unit.

  Signed-off-by: David Howells <dhowells@redhat.com>"

* tag 'disintegrate-main-20121013' of git://git.infradead.org/users/dhowells/linux-headers:
  UAPI: (Scripted) Disintegrate include/linux/byteorder
  UAPI: (Scripted) Disintegrate include/linux
  UAPI: Unexport linux/blk_types.h
  UAPI: Unexport part of linux/ppp-comp.h

Pull spi UAPI disintegration from David Howells:
 "This is to complete part of the Userspace API (UAPI) disintegration
  for which the preparatory patches were pulled recently.  After these
  patches, userspace headers will be segregated into:

        include/uapi/linux/.../foo.h

  for the userspace interface stuff, and:

        include/linux/.../foo.h

  for the strictly kernel internal stuff.
Signed-off-by: David Howells <dhowells@redhat.com>
  Acked-by: Grant Likely <grant.likely@secretlab.ca>"

* tag 'disintegrate-spi-20121009' of git://git.infradead.org/users/dhowells/linux-headers:
  UAPI: (Scripted) Disintegrate include/linux/spi

Pull OpenRISC uapi disintegration from Jonas Bonn:
 "OpenRISC UAPI disintegration work from David Howells"

* tag 'openrisc-uapi' of git://openrisc.net/jonas/linux:
  UAPI: (Scripted) Disintegrate arch/openrisc/include/asm

Pull user namespace compile fixes from Eric W Biederman:
 "This tree contains three trivial fixes.  One compiler warning, one
  thinko fix, and one build fix"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
  btrfs: Fix compilation with user namespace support enabled
  userns: Fix posix_acl_file_xattr_userns gid conversion
  userns: Properly print bluetooth socket uids

Pull md updates from NeilBrown:
 - "discard" support, some dm-raid improvements and other assorted bits
   and pieces.

* tag 'md-3.7' of git://neil.brown.name/md: (29 commits)
  md: refine reporting of resync/reshape delays.
  md/raid5: be careful not to resize_stripes too big.
  md: make sure manual changes to recovery checkpoint are saved.
  md/raid10: use correct limit variable
  md: writing to sync_action should clear the read-auto state.
  Subject: [PATCH] md:change resync_mismatches to atomic64_t to avoid races
  md/raid5: make sure to_read and to_write never go negative.
  md: When RAID5 is dirty, force reconstruct-write instead of read-modify-write.
  md/raid5: protect debug message against NULL derefernce.
  md/raid5: add some missing locking in handle_failed_stripe.
  MD: raid5 avoid unnecessary zero page for trim
  MD: raid5 trim support
  md/bitmap:Don't use IS_ERR to judge alloc_page().
  md/raid1: Don't release reference to device while handling read error.
  raid: replace list_for_each_continue_rcu with new interface
  add further __init annotations to crypto/xor.c
  DM RAID: Fix for "sync" directive ineffectiveness
  DM RAID: Fix comparison of index and quantity for "rebuild" parameter
  DM RAID: Add rebuild capability for RAID10
  DM RAID: Move 'rebuild' checking code to its own function
  ...

The large platform selection choice should be sorted by option string
so it's easy to find the platform you're looking for.  Fix the few
options which are out of this order.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

As suggested by Andrew Morton:

  This is a pet peeve of mine.  Any time there's a long list of items
  (header file inclusions, kconfig entries, array initalisers, etc) and
  someone wants to add a new item, they *always* go and stick it at the
  end of the list.

  Guys, don't do this.  Either put the new item into a randomly-chosen
  position or, probably better, alphanumerically sort the list.

lets sort all our select statements alphanumerically.  This commit was
created by the following perl:

while (<>) {
	while (/\\\s*$/) {
		$_ .= <>;
	}
	undef %selects if /^\s*config\s+/;
	if (/^\s+select\s+(\w+).*/) {
		if (defined($selects{$1})) {
			if ($selects{$1} eq $_) {
				print STDERR "Warning: removing duplicated $1 entry\n";
			} else {
				print STDERR "Error: $1 differently selected\n".
					"\tOld: $selects{$1}\n".
					"\tNew: $_\n";
				exit 1;
			}
		}
		$selects{$1} = $_;
		next;
	}
	if (%selects and (/^\s*$/ or /^\s+help/ or /^\s+---help---/ or
			  /^endif/ or /^endchoice/)) {
		foreach $k (sort (keys %selects)) {
			print "$selects{$k}";
		}
		undef %selects;
	}
	print;
}
if (%selects) {
	foreach $k (sort (keys %selects)) {
		print "$selects{$k}";
	}
}

It found two duplicates:

Warning: removing duplicated S5P_SETUP_MIPIPHY entry
Warning: removing duplicated HARDIRQS_SW_RESEND entry

and they are identical duplicates, hence the shrinkage in the diffstat
of two lines.

We have four testers reporting success of this change (Tony, Stephen,
Linus and Sekhar.)
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>