The ksz_switch_chips[] element for KSZ9477 says that port 5 is an xMII
port and it supports speeds of 10/100/1000. The device tree example does
declare a fixed-link at 1000, and RGMII is the only one of those modes
that supports this speed, so use this phy-mode.

The microchip,ksz8565 compatible string is not supported by the
microchip driver, however on Microchip's product page it says that there
are 5 ports, 4 of which have internal PHYs and the 5th is an
MII/RMII/RGMII port. It's a bit strange that this is port@6, but it is
probably just the way it is. Select an RGMII phy-mode for this one as
well.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Looking at b53_srab_phylink_get_caps() I get no indication of what PHY
modes does port 8 support, since it is implemented circularly based on
the p->mode retrieved from the device tree (and in PHY_INTERFACE_MODE_NA
it reports nothing to supported_interfaces).

However if I look at the b53_switch_chips[] element for BCM58XX_DEVICE_ID,
I see that port 8 is the IMP port, and SRAB means the IMP port is
internal to the SoC. So use phy-mode = "internal" in the example.

Note that this will make b53_srab_phylink_get_caps() go through the
"default" case and report PHY_INTERFACE_MODE_INTERNAL to
supported_interfaces, which is probably a good thing.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Looking at hellcreek_phylink_get_caps(), I see that depending on whether
is_100_mbits is set, speeds of 1G or of 100M will be advertised. The
de1soc_r1_pdata sets is_100_mbits to true.

The PHY modes declared in the capabilities are MII, RGMII and GMII. GMII
doesn't support 100Mbps, and as for RGMII, it would be a bit implausible
to me to support this PHY mode but limit it to only 25 MHz. So I've
settled on MII as a phy-mode in the example, and a fixed-link of
100Mbps.

As a side note, there exists such a thing as "rev-mii", because the MII
protocol is asymmetric, and "mii" is the designation for the MAC side
(expected to be connected to a PHY), and "rev-mii" is the designation
for the PHY side (expected to be connected to a MAC). I wonder whether
"mii" or "rev-mii" should actually be used here, since this is a CPU
port and presumably connected to another MAC.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Judging by xrs700x_phylink_get_caps(), I deduce that this switch
supports the RGMII modes on port 3, so state this phy-mode in the
example, such that users are encouraged to not rely on avoiding phylink
for this port.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Port event data must stored to port-state cache regardless of whether
the port uses phylink or not since this data is used by ethtool.

Fixes: 52323ef7 ("net: marvell: prestera: add phylink support")
Signed-off-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu>
Signed-off-by: Maksym Glubokiy <maksym.glubokiy@plvision.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to make the underneath API easier to change in the future,
prevent users from dereferencing fwnode from struct device.
Instead, use the specific dev_fwnode() API for that.
Signed-off-by: zhaoxiao <zhaoxiao@uniontech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

DECnet is an obsolete network protocol that receives more attention
from kernel janitors than users. It belongs in computer protocol
history museum not in Linux kernel.

It has been "Orphaned" in kernel since 2010. The iproute2 support
for DECnet was dropped in 5.0 release. The documentation link on
Sourceforge says it is abandoned there as well.

Leave the UAPI alone to keep userspace programs compiling.
This means that there is still an empty neighbour table
for AF_DECNET.

The table of /proc/sys/net entries was updated to match
current directories and reformatted to be alphabetical.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: David Ahern <dsahern@kernel.org>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Horatiu Vultur says:

====================
net: lan966x: Add lag support

Add lag support for lan966x.
First 4 patches don't do any changes to the current behaviour, they
just prepare for lag support. While the rest is to add the lag support.

v3->v4:
- aggregation configuration is global for all bonds, so make sure that
  there can't be enabled multiple configurations at the same time
- return error faster from lan966x_foreign_bridging_check, don't
  continue the search if the error is seen already
- flush fdb workqueue when a port leaves a bridge or lag.

v2->v3:
- return error code from 'switchdev_bridge_port_offload()'
- fix lan966x_foreign_dev_check(), it was missing lag support
- remove lan966x_lag_mac_add_entry and lan966x_mac_del_entry as
  they are not needed
- fix race conditions when accessing port->bond
- move FDB entries when a new port joins the lag if it has a lower

v1->v2:
- fix the LAG PGIDs when ports go down, in this way is not
  needed anymore the last patch of the series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend MAC support to support also lag interfaces:
1. In case an entry is learned on a port that is part of lag interface,
   then notify the upper layers that the entry is learned on the bond
   interface
2. If a port leaves the bond and the port is the first port in the lag
   group, then it is required to update all MAC entries to change the
   destination port.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Offload FDB entries when the original device is a lag interface. Because
all the ports under the lag have the same chip id, which is the chip id
of first port, then add the entries only for the first port.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add link aggregation hardware offload support for lan966x
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend lan966x_foreign_bridging_check to check also if the upper
interface is a lag device. Don't allow a lan966x port to be part of a
lag if it has foreign interfaces.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Expose lan966x_switchdev_nb and lan966x_switchdev_blocking_nb to the
lan966x_main.h file because they will be needed by the lag driver.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Whenever a port leaves a bridge, flush the workqueue of the FDB work.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Split the function lan966x_fdb_event_work. One case for when the
orig_dev is a bridge and one case when orig_dev is lan966x port.
This is preparation for lag support. There is no functional change.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the registers used by lan966x to configure the lag interface.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Gerhard Engleder says:

====================
tsnep: Various minor driver improvements

During XDP development some general driver improvements has been done
which I want to keep out of future patch series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Other drivers record RX queue so it should make sense to do that also.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

DMA addresses up to 64bit are supported by the device. Configure DMA
mask according to the capabilities of the device.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TX length can by calculated more efficient during map and unmap of
fragments. Another reason is that, by moving TX statistic counting to
tsnep_tx_poll() it can be used there for XDP too.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for NETIF_F_LOOPBACK feature. Loopback mode is used for
testing.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixed register define is not used, but register definition shall be kept
in sync.

Fixes: 403f69bb ("tsnep: Add TSN endpoint Ethernet MAC driver")
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently queue_userspace_packet will call kfree_skb for all frames,
whether or not an error occurred. This can result in a single dropped
frame being reported as multiple drops in dropwatch. This functions
caller may also call kfree_skb in case of an error. This patch will
consume the skbs instead and allow caller's to use kfree_skb.
Signed-off-by: Mike Pattrick <mkp@redhat.com>
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2109957Signed-off-by: David S. Miller <davem@davemloft.net>

Frames sent to userspace can be reported as dropped in
ovs_dp_process_packet, however, if they are dropped in the netlink code
then netlink_attachskb will report the same frame as dropped.

This patch checks for error codes which indicate that the frame has
already been freed.
Signed-off-by: Mike Pattrick <mkp@redhat.com>
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2109946Signed-off-by: David S. Miller <davem@davemloft.net>

Maxime Chevallier says:

====================
net: Introduce QUSGMII phy mode

Re-sending, since the previous v4 was sent while net-next was closed.

This is a resend of the V4 of a previous series [1] initially aimed at
introducing inband extensions, with modes like QUSGMII. This mode allows
passing info in the ethernet preamble between the MAC and the PHY, such as
timestamps.

This series has now become a preliminary series, that simply introduces
the new interface mode, without support for inband extensions, that will
come later.

The reasonning is that work will need to be done in the networking
subsystem, but also in the generic phy driver subsystem to allow serdes
configuration for qusgmii.

This series add the mode, the relevant binding changes, adds support for
it in the lan966x driver, and also introduces a small helper to get the
number of links a given phy mode can carry (think 1 for SGMII and 4 for
QSGMII). This allows for better readability and will prove useful
when (if) we support PSGMII (5 links on 1 interface) and OUSGMII (8
links on one interface).

V4 contains no change but the collected Reviewed-by from Andrew.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The Lan996x controller supports the QUSGMII mode, which is very similar
to QSGMII in the way it's configured and the autonegociation
capababilities it provides.

This commit adds support for that mode, treating it most of the time
like QSGMII, making sure that we do configure the PCS how we should.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some phy modes such as QSGMII multiplex several MAC<->PHY links on one
single physical interface. QSGMII used to be the only one supported, but
other modes such as QUSGMII also carry multiple links.

This helper allows getting the number of links that are multiplexed
on a given interface.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new QUSGMII mode, standing for "Quad Universal Serial Gigabit
Media Independent Interface", a derivative of USGMII which, similarly to
QSGMII, allows to multiplex 4 1Gbps links to a Quad-PHY.

The main difference with QSGMII is that QUSGMII can include an extension
instead of the standard 7bytes ethernet preamble, allowing to convey
arbitrary data such as Timestamps.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The QUSGMII mode is a derivative of Cisco's USXGMII standard. This
standard is pretty similar to SGMII, but allows for faster speeds, and
has the build-in bits for Quad and Octa variants (like QSGMII).

The main difference with SGMII/QSGMII is that USXGMII/QUSGMII re-uses
the preamble to carry various information, named 'Extensions'.

As of today, the USXGMII standard only mentions the "PCH" extension,
which is used to convey timestamps, allowing in-band signaling of PTP
timestamps without having to modify the frame itself.

This commit adds support for that mode. When no extension is in use, it
behaves exactly like QSGMII, although it's not compatible with QSGMII.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

On the CPSW and ICSS peripherals, there is a possibility that the MDIO
interface returns corrupt data on MDIO reads or writes incorrect data
on MDIO writes. There is also a possibility for the MDIO interface to
become unavailable until the next peripheral reset.

The workaround is to configure the MDIO in manual mode and disable the
MDIO state machine and emulate the MDIO protocol by reading and writing
appropriate fields in MDIO_MANUAL_IF_REG register of the MDIO controller
to manipulate the MDIO clock and data pins.

More details about the errata i2329 and the workaround is available in:
https://www.ti.com/lit/er/sprz487a/sprz487a.pdf

Add implementation to disable MDIO state machine, configure MDIO in manual
mode and achieve MDIO read and writes via MDIO Bitbanging
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

RTL8211F(D)(I)-VD-CG is the pin-to-pin upgrade chip from
RTL8211F(D)(I)-CG.

Add new PHY ID for this chip.
It does not support RTL8211F_PHYCR2 anymore, so remove the w/r operation
of this register.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TCP_LISTEN sockets is a special case. They preserve skb with a newly
connected sock till accept() makes it fully functional socket.
Receive queue of such socket may grow after connected peer
send messages there. Since these messages may contain scm_fds,
we should expose correct fdinfo::scm_fds for listening socket too.
Signed-off-by: Kirill Tkhai <tkhai@ya.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

Size-check a type used for FW communication is packed as expected.
Signed-off-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu>
Signed-off-by: Maksym Glubokiy <maksym.glubokiy@plvision.eu>
Link: https://lore.kernel.org/r/20220818111419.414877-1-maksym.glubokiy@plvision.euSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The skb pointer will be checked in kfree_skb(), so remove the outside check.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Taehee Yoo <ap420073@gmail.com>
Link: https://lore.kernel.org/r/20220818093114.2449179-1-yangyingliang@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

There are currently 3 ip tunnels that are capable of carrying
L2 traffic: gretap, vxlan and geneve.
They all are capable to inherit the TOS/TTL for the outer
IP-header from the inner frame.

Add a test that verifies that these fields are correctly inherited.

These tests failed before the following commits:
b09ab9c9 ("ip6_tunnel: allow to inherit from VLAN encapsulated IP")
3f8a8447 ("ip6_gre: use actual protocol to select xmit")
41337f52 ("ip6_gre: set DSCP for non-IP")
7ae29fd1 ("ip_tunnel: allow to inherit from VLAN encapsulated IP")
7074732c ("ip_tunnels: allow VXLAN/GENEVE to inherit TOS/TTL from VLAN")
ca2bb695 ("geneve: do not use RT_TOS for IPv6 flowlabel")
b4ab94d6 ("geneve: fix TOS inheriting for ipv4")
Signed-off-by: Matthias May <matthias.may@westermo.com>
Link: https://lore.kernel.org/r/20220817073649.26117-1-matthias.may@westermo.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Sean Anderson says:

====================
net: dpaa: Cleanups in preparation for phylink conversion

This series contains several cleanup patches for dpaa/fman. While they
are intended to prepare for a phylink conversion, they stand on their
own. This series was originally submitted as part of [1].

[1] https://lore.kernel.org/netdev/20220715215954.1449214-1-sean.anderson@seco.com
====================

Link: https://lore.kernel.org/r/20220818161649.2058728-1-sean.anderson@seco.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This option is present in params, so use it instead of the fman private
version.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In preparation for moving each of the initialization functions to their
own file, export some common functions so they can be re-used. This adds
an fman prefix to set_multi to make it a bit less genericly-named.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

memac is the only mac which parses fixed links. Move the
parsing/configuring to its initialization function.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Move the reference to our device to mac_device. This way, macs can use
it in their log messages.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>