This patch reformats the SSID to phy ID table, replacing constants with
preprocessor definitions.  This patch is also prep work for the
following patch, which will push line lengths beyond 80 chars.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The phy address will not change after it has been identified.  Move the
discovery code to a location that only gets executed once.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds an inverted "jumbo ring enable" test and jumps to the exit
if it succeeds.  The change reduces the indent level of the remaining
code making it more readable.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The STD part of this preprocessor definition is a bit of a misnomer.
This flag is a coarse control of the RGMII inband status facilities.
This patch renames the definition to be more accurate.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds 57765 asic partno entries for the path executed if VPD
is not present in NVRAM.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch loosens the restriction that the phylib interface must be up
and running to change the flow control parameters.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds new offsets to the bootcode version extraction code to
support NVRAM format versions 4 and 5.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the 57791 and 57795 to the list of devices that only
support 10 and 100 Mbps speeds.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan noted that there is nothing in the code that would prevent
the compiler from delaying the access of the "mapping" member of the
newly arrived packet until much later.  If this happened after the
skb = NULL assignment, it is possible for the driver to pass a bad
dma_addr value to pci_unmap_single().  To enforce this ordering, we need
a write memory barrier.  The pairing read memory barrier already exists
in tg3_rx_prodring_xfer() under the comments starting with
"Ensure that updates to the...".
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds Linux Socket Filter support to
tun driver.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Export sk_attach_filter/sk_detach_filter routines,
so that tun module can use them.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Removed whole t3_rx_mode structure and appropriate helpers cause they are no
longer needed.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use phy_find_first() function instead of manual lookup.
Signed-off-by: Denis Kirjanov <kirjanov@gmail.com>
Reviewed-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Traffic (tcp) doesnot start on a vlan interface when gro is enabled.
Even the tcp handshake was not taking place.
This is because, the eth_type_trans call before the netif_receive_skb
in napi_gro_finish() resets the skb->dev to napi->dev from the previously
set vlan netdev interface. This causes the ip_route_input to drop the
incoming packet considering it as a packet coming from a martian source.

I could repro this on 2.6.32.7 (stable) and 2.6.33-rc7.
With this fix, the traffic starts and the test runs fine on both vlan
and non-vlan interfaces.

CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix missing validate_addr hook.
Signed-off-by: Denis Kirjanov <kirjanov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adds device driver for Aeroflex Gaisler 10/100 and 10/100/1G Ethernet
MAC IP cores.
Signed-off-by: Kristoffer Glembo <kristoffer@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reduces CPU utilization significantly with sendfile for example.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes D-Link DGE-550T PCI ID (1186:4000) from the ipg
driver. The ipg driver is for IP2000-based cards and the DGE-550T is
a DL2000-based card. The driver loads and works for a few moments, but
once a real workload is applied it stops operating. The ipg driver
claimed this ID since it was introduced in 2.6.24 and it's forced many
users to blacklist it.

The correct driver for this hardware is the dl2k driver, which has been
claiming this PCI ID since the 2.4 days.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As reported by Alexey Dobriyan:

--------------------
setkey now takes several seconds to run this simple script
and it spits "recv: Resource temporarily unavailable" messages.

#!/usr/sbin/setkey -f
flush;
spdflush;

add A B ipcomp 44 -m tunnel -C deflate;
add B A ipcomp 45 -m tunnel -C deflate;

spdadd A B any -P in ipsec
        ipcomp/tunnel/192.168.1.2-192.168.1.3/use;
spdadd B A any -P out ipsec
        ipcomp/tunnel/192.168.1.3-192.168.1.2/use;
--------------------

Obviously applications want the events even when the table
is empty.  So we cannot make this behavioral change.
Signed-off-by: David S. Miller <davem@davemloft.net>

Adds half-duplex specific setup code (taken from SiS own GPL driver).
Without those, half-duplex connections are very unreliable, often
working on small transfers and failing after a while.
Signed-off-by: Riccardo Ghetta <birrachiara@tin.it>
Signed-off-by: David S. Miller <davem@davemloft.net>

The n-tuple list should be flushed if and only if the ETH_RESET_FILTER
flag is set and the driver is able to reset filtering/flow direction
hardware without also resetting a component whose flag is not set.
This test is best left to the driver.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Updated release version and date: 1.52.1-6 and 2010/02/16
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Switch to the new firmware version (5.2.13).
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

New firmware version (5.2.13).
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bug fix: Use the last unicast entry in CAM in bnx2x_test_int(). Relevant for 57710 only.

Author: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bug fix: Do not allow enabling LRO if disable_tpa=1.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bug fix: clean up MCP state in case of error in bnx2x_init_hw().

Author: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bug fix: Properly release allocated MSI-X/MSI vectors if ifup failed
due to lack of memory.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert from:
	if (netif_msg_<foo>(priv))
		dev_<level>(dev...
to
	netif_<level>(priv, foo, dev...

Also convert a few:

	if (i < REG_TIMEOUT) {
		etc...
		return ret;
       }
to
	if (i >= REG_TIMEOUT)
		goto fail;
	etc...
	return ret;
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These macros are too similar to the dev_<level> equivalents
but take a usbnet * argument.  Convert them to the recently
introduced netdev_<level> macros and remove the old macros.

The old macros had "\n" appended to the format string.
Add the "\n" to the converted uses.

Some existing uses of the dev<foo> macros in cdc_eem.c
probably mistakenly had trailing "\n".  No "\n" added there.

Fix net1080 this/other log message inversion.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The flush compl (compl with numfrags == 0; no data) is rcvd
from hw to indicate completion of RXQ destory operation. Fix
the RX path to not process it as RX data.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When an MCC cmd is issued (via a netdev/ethtool op)
while the device is not open, the MCC CQ gets processed but the EQ
is not processed (as isr is not registered.) This can cause the EQ
to become full. So, while the device is not open, CQ must not be re-armed
to prevent EQ entries.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce unlikely() for skb alloc failure and vlanf checks...
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On some servers we see the cleaning of the RX queue finish before all
the loopback packets are sent out.  This delay allows the queues to
settle before checking for successful completion.
Also, delay completion so link has time to come back up.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use local copy of current mac address when initializing.  In bonding
testing we saw cases where dev_addr was out of data causing failover
errors.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This was found with pings that were large enough to span multiple rx
buffers.  The split frame logic handles this case nicely.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A userland command to set the LLTEMAC MAC address,
i.e. "ifconfig eth0 hw addr xx:yy:zz:pp:dd:qq",
results in a device address of 00:01:xx:yy:zz:pp.
Correct this.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

LLTEMAC V1 cores place only received packet length in the app4 word.
V2 cores place additional information in app4.
Mask out the additional information when retrieving the packet length.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>