For connac3 chipsets, setting of spe_idx is moved from TX descriptor to
the fixed rate table. This patch implements the setting to support
duplicate TX mode for beacon.
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

This patch adds support for thermal sensor device, including the
following features:
- Support to read current chip temperature.
- Support to set/get the trigger/restore temperature for thermal service.
- Support to read current chip tx cycle.
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Implement thermal protection commands and support Linux cooling device
control for mt7996 chipsets.
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add EHT statistics of beamforming feedback and BW320 in debugfs tx_stats
command.
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add support to correctly configure the rx chainmask of variants that
have additional auxiliary RX path. e.g., 4T5R.
The auxiliary RX path is transparent to driver, but driver needs to
correctly configure it in the set channel fw command.
Co-developed-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

wifi: mt76: mt7915: fallback to non-wed mode if platform_get_resource fails in mt7915_mmio_wed_init()

mt76 assumes mt7915_mmio_wed_init can fail just after wed driver has
been attached running mtk_wed_device_attach().
Fall back to non-wed mode if platform_get_resource fails in
mt7915_mmio_wed_init routines.

Fixes: eebb7097 ("wifi: mt76: mt7915: enable wed for mt7986-wmac chipset")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce the capability to clear WED rro session configured in the hw
according to the event reported by the MCU firmware
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Co-developed-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce the capability to reset mt7996 chipset if requested by wed
driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move WED reset code shared between mt7915 and mt7996 in common module.
This is a preliminary patch to introduce WED reset support for mt7996.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Similar to MT7915, enable Wireless Ethernet Ditpatcher for MT7996
to offload traffic received from the WLAN nic and transmitted on the
LAN one
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

This is a preliminary patch to introduce WED rx support for mt7996
driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

This is a preliminary patch to introduce WED support for mt7996
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Similar to MT7915, enable Wireless Ethernet Ditpatcher for MT7996
to offload traffic received from the LAN nic and transmitted on the
WLAN one
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

This is a preliminary patch to introduce WED support for mt7996
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce mtk_wed_device pointer in mt76_queue structure in order to
configure WED chip.
Get rid of dev parameter in Q_READ and Q_WRITE macros.
Introduce wed parameter to the following routine signatures:
- mt76_init_queue
- mt76_init_tx_queue

This is a preliminary patch to introduce WED support for mt7996 since
mt7996 runs two separate WED chips.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

This is a preliminary patch to introduce WED support for mt7996
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

This is a preliminary patch to introduce WED support for mt7996
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76_mmio_wed_offload_enable and mt76_mmio_wed_offload_disable routines
will be reused by mt7996 driver for wed support.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move mt76_mmio_wed_init_rx_buf and mt76_mmio_wed_release_rx_buf routines
in common code.
This is a preliminary patch to introduce WED support for mt7996
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

No need cast (void *) to (struct mt7615_phy *).
Signed-off-by: Wu Yunchuan <yunchuan@nfschina.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Permit to load precal from NVMEM cell for mt7915. The NVMEM cell must be
named "precal" to be correctly loaded.

NVMEM cell must already account the correct offset and be placed after
the EEPROM as the function expect the data right from the start.
Tested-by: Shiji Yang <yangshiji66@outlook.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Generilize mt76_get_of_eeprom_from_nvmem to use alternative cell name by
passing the cell name as an arg and expose it.

Rename it to mt76_get_of_data_from_nvmem to better reflect the now more
generic usage.

This is to permit driver to load additional cell, like precal cell.
Tested-by: Shiji Yang <yangshiji66@outlook.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Since mt76_get_of_eeprom is not used by mt7915 anymore, unexport it and
make it static again.

Also drop offset arg as it's only supported for MTD and was always set
to 0, hardcode the MTD functio instead.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Limit support for precal loading for mt7915 only to MTD. Passing data
from DT doesn't support offset and NVMEM require a different cell name
and doesn't support offset hence only MTD way is actually supported.

Rename mt76_get_of_eeprom_from_mtd to mt76_get_of_data_from_mtd as it is
now used for a more generic purpose and export it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fix typo in mt76_get_of_eeprom_from_nvmem where eeprom was misspelled as
epprom.

Fixes: 5bef3a40 ("wifi: mt76: add support for providing eeprom in nvmem cells")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Commit 495184ac ("mt76: mt7915: add support for applying
pre-calibration data") was fundamentally broken and never worked.

The idea (before NVMEM support) was to expand the MTD function and pass
an additional offset. For normal EEPROM load the offset would always be
0. For the purpose of precal loading, an offset was passed that was
internally the size of EEPROM, since precal data is right after the
EEPROM.

Problem is that the offset value passed is never handled and is actually
overwrite by

	offset = be32_to_cpup(list);
	ret = mtd_read(mtd, offset, len, &retlen, eep);

resulting in the passed offset value always ingnored. (and even passing
garbage data as precal as the start of the EEPROM is getting read)

Fix this by adding to the current offset value, the offset from DT to
correctly read the piece of data at the requested location.

Cc: stable@vger.kernel.org
Fixes: 495184ac ("mt76: mt7915: add support for applying pre-calibration data")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fix the uninitialized variable warning in mt7996_mac_tx_free.

Fixes: 2461599f ("wifi: mt76: mt7996: get tx_retries and tx_failed from txfree")
Signed-off-by: Yi-Chia Hsieh <yi-chia.hsieh@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

The mtcl table, configured by platform vendor, provides regulatory
information for 5.9/6 GHz channels. mt792x should work on
corresponding channels supported by mtcl. This patch would parse
the settings in mtcl table and apply the result into chip side.
Signed-off-by: Rong Yan <rong.yan@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add ability to explicitly forbid LED registration using DT led\status = "disabled".
Tested-by: Alexey D. Filimonov <alexey@filimonic.net>
Signed-off-by: Alexey D. Filimonov <alexey@filimonic.net>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Don't enable firmware debug mode to prevent SER flow stuck due to fail
to reset payload buffer, and clear HALT_C2H_INT to avoid handling
unexpected interrupt at beginning.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231204080751.15354-6-pkshih@realtek.com

To diagnose the reason why firmware or hardware get abnormal, add to dump
MAC registers related to counters and interrupt masks. With these values,
people can classify problems and check if registers values are unexpected,
and then correct them. However, it could possible false alarm because
firmware triggers this SER event by wrong conditions that we should
correct it at firmware or register settings.

In field, SER might happen under special conditions, and very hard to
happen again, so dump lots of registers to provide rich information to
catch the problem.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231204080751.15354-5-pkshih@realtek.com

To activate SER (system error recovery) in firmware, we have to configure
IMR to trigger interrupts, and then SER can check registers to know if it
need to reset hardware or notify driver to re-configure whole settings.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231204080751.15354-4-pkshih@realtek.com

Extend FW program counter dump for Wi-Fi 7 chip.
They poll different addresses.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231204080751.15354-3-pkshih@realtek.com

RTL8922A FW supports CRASH_TRIGGER feature from v0.34.30.0.
After it, debugfs fw_crash can accept type 1 on RTL8922A to
trigger firmware crash and verify L2 recovery.

Besides, RTL8922A sync address offset of reserved payload engine.
And, SER (system error recovery) tweaks conversion from WCPU address
to indirect access address for RTL8922A. The new conversion works
for all supported chips.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231204080751.15354-2-pkshih@realtek.com

This is just a collection of data and we only read it,
so make it const.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This function has so many arguments already, before adding
yet another one, refactor it to take a struct instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In concurrent mode, when STA interface is scanning, it causes
AP interface TX beacon on wrong channel. We modified it to scan
with the operating channel when one of the interfaces is already
connected. Additionally, STA interface need to stop scan when AP
interface is starting to avoid TX beacon on wrong channel. Finally,
AP interface need to stop TX beacon when STA interface is scanning
and switching to non-OP channel,This prevent other device to get
beacons on wrong channel.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231129070046.18443-5-pkshih@realtek.com

We add a scanning check to avoid entering IPS after ROC (remain on
channel) during scanning. Additionally, When P2P scanning, the flow is
`1. p2p_listen step` and `2. configure filter` and `3. p2p_scan starts`
in wpas, but in kernel, cfg80211 uses another workqueue to notify driver
the filter change, so sometimes we see (1 > 3 > 2), that will cause Rx
filter related to scan to be cleared. Therefore, we add a scanning check
when configure filter to avoid scan results to be filtered. Finally, we
cancel the ROC delayed workqueue before entering ROC to avoid entering
twice, which might cause leaving ROC too early.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231129070046.18443-4-pkshih@realtek.com

The interval between sending each probe request is regulated. Before
this patch, some packets are not sent out properly because of our HW
limit. Extend the 6 GHz channel dwell time to cope with this.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231129070046.18443-3-pkshih@realtek.com

The attempt to enter power save mode might fail if there are still
beacons pending in the queue. This sometimes happens after stopping
P2P GO or AP mode. Extend stop AP function and flush all beacons to
resolve this.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231129070046.18443-2-pkshih@realtek.com