- 05 May, 2014 19 commits
-
-
Leon Ma authored
commit 012a45e3 upstream. If a cpu is idle and starts an hrtimer which is not pinned on that same cpu, the nohz code might target the timer to a different cpu. In the case that we switch the cpu base of the timer we already have a sanity check in place, which determines whether the timer is earlier than the current leftmost timer on the target cpu. In that case we enqueue the timer on the current cpu because we cannot reprogram the clock event device on the target. If the timers base is already the target CPU we do not have this sanity check in place so we enqueue the timer as the leftmost timer in the target cpus rb tree, but we cannot reprogram the clock event device on the target cpu. So the timer expires late and subsequently prevents the reprogramming of the target cpu clock event device until the previously programmed event fires or a timer with an earlier expiry time gets enqueued on the target cpu itself. Add the same target check as we have for the switch base case and start the timer on the current cpu if it would become the leftmost timer on the target. [ tglx: Rewrote subject and changelog ] Signed-off-by:
Leon Ma <xindong.ma@intel.com> Link: http://lkml.kernel.org/r/1398847391-5994-1-git-send-email-xindong.ma@intel.comSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Stuart Hayes authored
commit 6c6c0d5a upstream. If the last hrtimer interrupt detected a hang it sets hang_detected=1 and programs the clock event device with a delay to let the system make progress. If hang_detected == 1, we prevent reprogramming of the clock event device in hrtimer_reprogram() but not in hrtimer_force_reprogram(). This can lead to the following situation: hrtimer_interrupt() hang_detected = 1; program ce device to Xms from now (hang delay) We have two timers pending: T1 expires 50ms from now T2 expires 5s from now Now T1 gets canceled, which causes hrtimer_force_reprogram() to be invoked, which in turn programs the clock event device to T2 (5 seconds from now). Any hrtimer_start after that will not reprogram the hardware due to hang_detected still being set. So we effectivly block all timers until the T2 event fires and cleans up the hang situation. Add a check for hang_detected to hrtimer_force_reprogram() which prevents the reprogramming of the hang delay in the hardware timer. The subsequent hrtimer_interrupt will resolve all outstanding issues. [ tglx: Rewrote subject and changelog and fixed up the comment in hrtimer_force_reprogram() ] Signed-off-by:
Stuart Hayes <stuart.w.hayes@gmail.com> Link: http://lkml.kernel.org/r/53602DC6.2060101@gmail.comSigned-off-by:
-
Grant Likely authored
commit 58b116bc upstream. When the kernel is built with CONFIG_PREEMPT it is possible to reach a state when all modules loaded but some driver still stuck in the deferred list and there is a need for external event to kick the deferred queue to probe these drivers. The issue has been observed on embedded systems with CONFIG_PREEMPT enabled, audio support built as modules and using nfsroot for root filesystem. The following log fragment shows such sequence when all audio modules were loaded but the sound card is not present since the machine driver has failed to probe due to missing dependency during it's probe. The board is am335x-evmsk (McASP<->tlv320aic3106 codec) with davinci-evm machine driver: ... [ 12.615118] davinci-mcasp 4803c000.mcasp: davinci_mcasp_probe: ENTER [ 12.719969] davinci_evm sound.3: davinci_evm_probe: ENTER [ 12.725753] davinci_evm sound.3: davinci_evm_probe: snd_soc_register_card [ 12.753846] davinci-mcasp 4803c000.mcasp: davinci_mcasp_probe: snd_soc_register_component [ 12.922051] davinci-mcasp 4803c000.mcasp: davinci_mcasp_probe: snd_soc_register_component DONE [ 12.950839] davinci_evm sound.3: ASoC: platform (null) not registered [ 12.957898] davinci_evm sound.3: davinci_evm_probe: snd_soc_register_card DONE (-517) [ 13.099026] davinci-mcasp 4803c000.mcasp: Kicking the deferred list [ 13.177838] davinci-mcasp 4803c000.mcasp: really_probe: probe_count = 2 [ 13.194130] davinci_evm sound.3: snd_soc_register_card failed (-517) [ 13.346755] davinci_mcasp_driver_init: LEAVE [ 13.377446] platform sound.3: Driver davinci_evm requests probe deferral [ 13.592527] platform sound.3: really_probe: probe_count = 0 In the log the machine driver enters it's probe at 12.719969 (this point it has been removed from the deferred lists). McASP driver already executing it's probing (since 12.615118). The machine driver tries to construct the sound card (12.950839) but did not found one of the components so it fails. After this McASP driver registers all the ASoC components (the machine driver still in it's probe function after it failed to construct the card) and the deferred work is prepared at 13.099026 (note that this time the machine driver is not in the lists so it is not going to be handled when the work is executing). Lastly the machine driver exit from it's probe and the core places it to the deferred list but there will be no other driver going to load and the deferred queue is not going to be kicked again - till we have external event like connecting USB stick, etc. The proposed solution is to try the deferred queue once more when the last driver is asking for deferring and we had drivers loaded while this last driver was probing. This way we can avoid drivers stuck in the deferred queue. Signed-off-by:
Grant Likely <grant.likely@linaro.org> Reviewed-by:
Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Mark Brown <broonie@kernel.org> Signed-off-by:
-
Fam Zheng authored
commit 0c8482ac upstream. virtscsi_init calls virtscsi_remove_vqs on err, even before initializing the vqs. The latter calls virtscsi_set_affinity, so let's check the pointer there before setting affinity on it. This fixes a panic when setting device's num_queues=2 on RHEL 6.5: qemu-system-x86_64 ... \ -device virtio-scsi-pci,id=scsi0,addr=0x13,...,num_queues=2 \ -drive file=/stor/vm/dummy.raw,id=drive-scsi-disk,... \ -device scsi-hd,drive=drive-scsi-disk,... [ 0.354734] scsi0 : Virtio SCSI HBA [ 0.379504] BUG: unable to handle kernel NULL pointer dereference at 0000000000000020 [ 0.380141] IP: [<ffffffff814741ef>] __virtscsi_set_affinity+0x4f/0x120 [ 0.380141] PGD 0 [ 0.380141] Oops: 0000 [#1] SMP [ 0.380141] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.14.0+ #5 [ 0.380141] Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2007 [ 0.380141] task: ffff88003c9f0000 ti: ffff88003c9f8000 task.ti: ffff88003c9f8000 [ 0.380141] RIP: 0010:[<ffffffff814741ef>] [<ffffffff814741ef>] __virtscsi_set_affinity+0x4f/0x120 [ 0.380141] RSP: 0000:ffff88003c9f9c08 EFLAGS: 00010256 [ 0.380141] RAX: 0000000000000000 RBX: ffff88003c3a9d40 RCX: 0000000000001070 [ 0.380141] RDX: 0000000000000002 RSI: 0000000000000000 RDI: 0000000000000000 [ 0.380141] RBP: ffff88003c9f9c28 R08: 00000000000136c0 R09: ffff88003c801c00 [ 0.380141] R10: ffffffff81475229 R11: 0000000000000008 R12: 0000000000000000 [ 0.380141] R13: ffffffff81cc7ca8 R14: ffff88003cac3d40 R15: ffff88003cac37a0 [ 0.380141] FS: 0000000000000000(0000) GS:ffff88003e400000(0000) knlGS:0000000000000000 [ 0.380141] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b [ 0.380141] CR2: 0000000000000020 CR3: 0000000001c0e000 CR4: 00000000000006f0 [ 0.380141] Stack: [ 0.380141] ffff88003c3a9d40 0000000000000000 ffff88003cac3d80 ffff88003cac3d40 [ 0.380141] ffff88003c9f9c48 ffffffff814742e8 ffff88003c26d000 ffff88003c26d000 [ 0.380141] ffff88003c9f9c68 ffffffff81474321 ffff88003c26d000 ffff88003c3a9d40 [ 0.380141] Call Trace: [ 0.380141] [<ffffffff814742e8>] virtscsi_set_affinity+0x28/0x40 [ 0.380141] [<ffffffff81474321>] virtscsi_remove_vqs+0x21/0x50 [ 0.380141] [<ffffffff81475231>] virtscsi_init+0x91/0x240 [ 0.380141] [<ffffffff81365290>] ? vp_get+0x50/0x70 [ 0.380141] [<ffffffff81475544>] virtscsi_probe+0xf4/0x280 [ 0.380141] [<ffffffff81363ea5>] virtio_dev_probe+0xe5/0x140 [ 0.380141] [<ffffffff8144c669>] driver_probe_device+0x89/0x230 [ 0.380141] [<ffffffff8144c8ab>] __driver_attach+0x9b/0xa0 [ 0.380141] [<ffffffff8144c810>] ? driver_probe_device+0x230/0x230 [ 0.380141] [<ffffffff8144c810>] ? driver_probe_device+0x230/0x230 [ 0.380141] [<ffffffff8144ac1c>] bus_for_each_dev+0x8c/0xb0 [ 0.380141] [<ffffffff8144c499>] driver_attach+0x19/0x20 [ 0.380141] [<ffffffff8144bf28>] bus_add_driver+0x198/0x220 [ 0.380141] [<ffffffff8144ce9f>] driver_register+0x5f/0xf0 [ 0.380141] [<ffffffff81d27c91>] ? spi_transport_init+0x79/0x79 [ 0.380141] [<ffffffff8136403b>] register_virtio_driver+0x1b/0x30 [ 0.380141] [<ffffffff81d27d19>] init+0x88/0xd6 [ 0.380141] [<ffffffff81d27c18>] ? scsi_init_procfs+0x5b/0x5b [ 0.380141] [<ffffffff81ce88a7>] do_one_initcall+0x7f/0x10a [ 0.380141] [<ffffffff81ce8aa7>] kernel_init_freeable+0x14a/0x1de [ 0.380141] [<ffffffff81ce8b3b>] ? kernel_init_freeable+0x1de/0x1de [ 0.380141] [<ffffffff817dec20>] ? rest_init+0x80/0x80 [ 0.380141] [<ffffffff817dec29>] kernel_init+0x9/0xf0 [ 0.380141] [<ffffffff817e68fc>] ret_from_fork+0x7c/0xb0 [ 0.380141] [<ffffffff817dec20>] ? rest_init+0x80/0x80 [ 0.380141] RIP [<ffffffff814741ef>] __virtscsi_set_affinity+0x4f/0x120 [ 0.380141] RSP <ffff88003c9f9c08> [ 0.380141] CR2: 0000000000000020 [ 0.380141] ---[ end trace 8074b70c3d5e1d73 ]--- [ 0.475018] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000009 [ 0.475018] [ 0.475068] Kernel Offset: 0x0 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffff9fffffff) [ 0.475068] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000009 [jejb: checkpatch fixes] Signed-off-by:
Fam Zheng <famz@redhat.com> Acked-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
James Bottomley <JBottomley@Parallels.com> Signed-off-by:
-
Tyler Stachecki authored
commit af61e27c upstream. On suspend, _scsih_suspend calls mpt2sas_base_free_resources, which in turn calls pci_disable_device if the device is enabled prior to suspending. However, _scsih_suspend also calls pci_disable_device itself. Thus, in the event that the device is enabled prior to suspending, pci_disable_device will be called twice. This patch removes the duplicate call to pci_disable_device in _scsi_suspend as it is both unnecessary and results in a kernel oops. Signed-off-by:
Tyler Stachecki <tstache1@binghamton.edu> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit a949ae56 upstream. A race exists between module loading and enabling of function tracer. CPU 1 CPU 2 ----- ----- load_module() module->state = MODULE_STATE_COMING register_ftrace_function() mutex_lock(&ftrace_lock); ftrace_startup() update_ftrace_function(); ftrace_arch_code_modify_prepare() set_all_module_text_rw(); <enables-ftrace> ftrace_arch_code_modify_post_process() set_all_module_text_ro(); [ here all module text is set to RO, including the module that is loading!! ] blocking_notifier_call_chain(MODULE_STATE_COMING); ftrace_init_module() [ tries to modify code, but it's RO, and fails! ftrace_bug() is called] When this race happens, ftrace_bug() will produces a nasty warning and all of the function tracing features will be disabled until reboot. The simple solution is to treate module load the same way the core kernel is treated at boot. To hardcode the ftrace function modification of converting calls to mcount into nops. This is done in init/main.c there's no reason it could not be done in load_module(). This gives a better control of the changes and doesn't tie the state of the module to its notifiers as much. Ftrace is special, it needs to be treated as such. The reason this would work, is that the ftrace_module_init() would be called while the module is in MODULE_STATE_UNFORMED, which is ignored by the set_all_module_text_ro() call. Link: http://lkml.kernel.org/r/1395637826-3312-1-git-send-email-indou.takao@jp.fujitsu.comReported-by:
Takao Indoh <indou.takao@jp.fujitsu.com> Acked-by:
Rusty Russell <rusty@rustcorp.com.au> Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Haibin Wang authored
commit 91021a6c upstream. When dispatch SGI(mode == 0), that is the vcpu of VM should send sgi to the cpu which the target_cpus list. So, there must add the "break" to branch of case 0. Signed-off-by:
Haibin Wang <wanghaibin.wang@huawei.com> Acked-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by:
-
Mark Salter authored
commit 5d4e08c4 upstream. The kvm/mmu code shared by arm and arm64 uses kalloc() to allocate a bounce page (if hypervisor init code crosses page boundary) and hypervisor PGDs. The problem is that kalloc() does not guarantee the proper alignment. In the case of the bounce page, the page sized buffer allocated may also cross a page boundary negating the purpose and leading to a hang during kvm initialization. Likewise the PGDs allocated may not meet the minimum alignment requirements of the underlying MMU. This patch uses __get_free_page() to guarantee the worst case alignment needs of the bounce page and PGDs on both arm and arm64. Signed-off-by:
Mark Salter <msalter@redhat.com> Acked-by:
-
Martin Schwidefsky authored
commit 6e0de817 upstream. The A register needs to be initialized to zero in the prolog if the first instruction of the BPF program is BPF_S_LDX_B_MSH to prevent leaking the content of %r5 to user space. Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Thomas Hellstrom authored
commit cbd75e97 upstream. We already check that the buffer object we're accessing is registered with the file. Now also make sure that we can't DMA across buffer object boundaries. v2: Code commenting update. Signed-off-by:
Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by:
Jakob Bornecrantz <jakob@vmware.com> Signed-off-by:
-
Daniel Vetter authored
commit 9953599b upstream. ... our current modeset code isn't good enough yet to handle this. The scenario is: 1. BIOS sets up a cloned config with lvds+external screen on the same pipe, e.g. pipe B. 2. We read out that state for pipe B and assign the gmch_pfit state to it. 3. The initial modeset switches the lvds to pipe A but due to lack of atomic modeset we don't recompute the config of pipe B. -> both pipes now claim (in the sw pipe config structure) to use the gmch_pfit, which just won't work. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=74081Tested-by:
max <manikulin@gmail.com> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
Jani Nikula <jani.nikula@intel.com> [ luis: backported to 3.11: adjusted context ] Signed-off-by:
-
Sebastian Ott authored
commit 06cd7a87 upstream. Using a notification type mask for the store event information chsc is unsupported on some firmware levels. Retry SEI with that mask set to zero (which is the old way of requesting only channel subsystem related events). Reported-and-tested-by:
Stefan Haberland <stefan.haberland@de.ibm.com> Reviewed-by:
Peter Oberparleiter <oberpar@linux.vnet.ibm.com> Signed-off-by:
Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by:
-
Sergey Dyasly authored
commit 3159f372 upstream. With LPAE enabled, physical address space is larger than 4GB. Allow mapping any part of it via /dev/mem by using PHYS_MASK to determine valid range. PHYS_MASK covers 40 bits with LPAE enabled and 32 bits otherwise. Reported-by:
Vassili Karpov <av1474@comtv.ru> Signed-off-by:
Sergey Dyasly <dserrg@gmail.com> Acked-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Cc: hujianyang <hujianyang@huawei.com> Signed-off-by:
-
Dan Carpenter authored
commit e2c70425 upstream. The original code always set the upper 32 bits to zero because it was doing a shift of the wrong variable. Fixes: 1a4f550a ('[SCSI] arcmsr: 1.20.00.15: add SATA RAID plus other fixes') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Dan Carpenter authored
commit b2a72ec3 upstream. qla2x00_mem_alloc() returns 1 on success and -ENOMEM on failure. On the one hand the caller assumes non-zero is success but on the other hand the caller also assumes that it returns an error code. I've fixed it to return zero on success and a negative error code on failure. This matches the documentation as well. [jejb: checkpatch fix] Fixes: e315cd28 ('[SCSI] qla2xxx: Code changes for qla data structure refactoring') Signed-off-by:
Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by:
-
Igor Gnatenko authored
commit 6db249eb upstream. After suspend another Renesas PCI-X USB 3.0 card doesn't work. [root@fedora-20 ~]# lspci -vmnnd 1912: Device: 03:00.0 Class: USB controller [0c03] Vendor: Renesas Technology Corp. [1912] Device: uPD720202 USB 3.0 Host Controller [0015] SVendor: Renesas Technology Corp. [1912] SDevice: uPD720202 USB 3.0 Host Controller [0015] Rev: 02 ProgIf: 30 This patch should be applied to stable kernel 3.14 that contain the commit 1aa9578c "xhci: Fix resume issues on Renesas chips in Samsung laptops" Reported-and-tested-by:
Anatoly Kharchenko <rfr-bugs@yandex.ru> Reference: http://redmine.russianfedora.pro/issues/1315Signed-off-by:
Igor Gnatenko <i.gnatenko.brain@gmail.com> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Nishanth Menon authored
commit 07484ca3 upstream. Just like IS_PM34XX_ERRATUM, IS_PM44XX_ERRATUM is valid only if CONFIG_PM is enabled, else, disabling CONFIG_PM results in build failure complaining about the following: arch/arm/mach-omap2/built-in.o: In function `omap4_boot_secondary': :(.text+0x8a70): undefined reference to `pm44xx_errata' Fixes: c9621844 (ARM: OMAP4: PM: add errata support) Reported-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
Nishanth Menon <nm@ti.com> Acked-by:
Santosh Shilimkar <santosh.shilimkar@ti.ocm> Acked-by:
Kevin Hilman <khilman@linaro.org> Signed-off-by:
-
Roger Quadros authored
commit c6c56697 upstream. OMAP3 doesn't contain "l3_init_clkdm" clock domain. Use the proper clock domains for USB Host and USB TLL modules. Gets rid of the following warnings during boot omap_hwmod: usb_host_hs: could not associate to clkdm l3_init_clkdm omap_hwmod: usb_tll_hs: could not associate to clkdm l3_init_clkdm Reported-by:
Roger Quadros <rogerq@ti.com> Fixes: de231388 ("ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP3") Cc: Keshava Munegowda <keshava_mgowda@ti.com> Cc: Partha Basak <parthab@india.ti.com> Signed-off-by:
Paul Walmsley <paul@pwsan.com> Signed-off-by:
-
Thomas Petazzoni authored
commit a6e03dd4 upstream. The mvmdio driver accesses some register of the Ethernet unit. It therefore takes a reference and enables a clock. However, on Armada 370/XP, no clock specification was given in the Device Tree, which leads the mvmdio driver to fail when being used as a module and loaded before the mvneta driver: it tries to access a register from a hardware unit that isn't clocked. Signed-off-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Link: https://lkml.kernel.org/r/1395790439-21332-2-git-send-email-thomas.petazzoni@free-electrons.comAcked-by:
Andrew Lunn <andrew@lunn.ch> Acked-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by:
Jason Cooper <jason@lakedaemon.net> [ luis: backported to 3.11: adjusted context ] Signed-off-by:
-
- 02 May, 2014 3 commits
-
-
Christopher Covington authored
commit 95c52fe0 upstream. The kcmp system call was ported to ARM in commit 3f7d1fe1 "ARM: 7665/1: Wire up kcmp syscall". Fixes: 3f7d1fe1 ("ARM: 7665/1: Wire up kcmp syscall") Signed-off-by:
Christopher Covington <cov@codeaurora.org> Signed-off-by:
-
Tedd Ho-Jeong An authored
commit ef4e5e4a upstream. This patch adds support for new Intel Bluetooth device. T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=8087 ProdID=0a2a Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by:
Tedd Ho-Jeong An <tedd.an@intel.com> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Petr Mladek authored
commit 12729f14 upstream. If a failure occurs while modifying ftrace function, it bails out and will remove the tracepoints to be back to what the code originally was. There is missing the final sync run across the CPUs after the fix up is done and before the ftrace int3 handler flag is reset. Here's the description of the problem: CPU0 CPU1 ---- ---- remove_breakpoint(); modifying_ftrace_code = 0; [still sees breakpoint] <takes trap> [sees modifying_ftrace_code as zero] [no breakpoint handler] [goto failed case] [trap exception - kernel breakpoint, no handler] BUG() Link: http://lkml.kernel.org/r/1393258342-29978-2-git-send-email-pmladek@suse.cz Fixes: 8a4d0a68 "ftrace: Use breakpoint method to update ftrace caller" Acked-by:
Frederic Weisbecker <fweisbec@gmail.com> Acked-by:
H. Peter Anvin <hpa@linux.intel.com> Signed-off-by:
Petr Mladek <pmladek@suse.cz> Signed-off-by:
-
- 30 Apr, 2014 3 commits
-
-
Chew, Kean ho authored
commit 1b31e9b7 upstream. Add Device ID of Intel BayTrail SMBus Controller. Signed-off-by:
Chew, Kean ho <kean.ho.chew@intel.com> Signed-off-by:
Chew, Chiau Ee <chiau.ee.chew@intel.com> Reviewed-by:
Jean Delvare <jdelvare@suse.de> Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Cc: Rebecca Swee Fun Chang <rebecca.swee.fun.chang@intel.com> Signed-off-by:
-
James Ralston authored
commit afc65924 upstream. This patch adds the SMBus Device IDs for the Intel Wildcat Point-LP PCH. Signed-off-by:
James Ralston <james.d.ralston@intel.com> Signed-off-by:
-
Tim Chen authored
commit 130fa5bc upstream. The crypto algorithm modules utilizing the crypto daemon could be used early when the system start up. Using module_init does not guarantee that the daemon's work queue is initialized when the cypto alorithm depending on crypto_wq starts. It is necessary to initialize the crypto work queue earlier at the subsystem init time to make sure that it is initialized when used. Signed-off-by:
Tim Chen <tim.c.chen@linux.intel.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
- 29 Apr, 2014 15 commits
-
-
Bjørn Mork authored
commit 34f972d6 upstream. A number of older CMOTech modems are based on Qualcomm chips. The blacklisted interfaces are QMI/wwan. Reported-by:
Lars Melin <larsm17@gmail.com> Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Bjørn Mork authored
commit dd6b48ec upstream. Device interface layout: 0: ff/ff/ff - serial 1: ff/00/00 - serial AT+PPP 2: ff/ff/ff - QMI/wwan 3: 08/06/50 - storage Signed-off-by:
-
Bjørn Mork authored
commit 533b3994 upstream. Device interface layout: 0: ff/ff/ff - serial 1: ff/ff/ff - serial AT+PPP 2: 08/06/50 - storage 3: ff/ff/ff - serial 4: ff/ff/ff - QMI/wwan Reported-by:
Julio Araujo <julio.araujo@wllctel.com.br> Signed-off-by:
-
Bjørn Mork authored
commit bce4f588 upstream. Signed-off-by:
-
Bjørn Mork authored
commit 70a3615f upstream. Signed-off-by:
-
Bjørn Mork authored
commit a00986f8 upstream. Signed-off-by:
-
Johan Hovold authored
commit 5509076d upstream. During firmware download the device expects memory addresses in big-endian byte order. As the wIndex parameter which hold the address is sent in little-endian byte order regardless of host byte order, we need to use swab16 rather than cpu_to_be16. Also make sure to handle the struct ti_i2c_desc size parameter which is returned in little-endian byte order. Reported-by:
Ludovic Drolez <ldrolez@debian.org> Tested-by:
Johan Hovold <jhovold@gmail.com> Signed-off-by:
-
David Cohen authored
commit 01bb59eb upstream. When CONFIG_PCI and CONFIG_PM are not selected, xhci.c gets this warning: drivers/usb/host/xhci.c:409:13: warning: ‘xhci_msix_sync_irqs’ defined but not used [-Wunused-function] Instead of creating nested #ifdefs, this patch fixes it by defining the xHCI PCI stubs as inline. This warning has been in since 3.2 kernel and was caused by commit 421aa841 "usb/xhci: hide MSI code behind PCI bars", but wasn't noticed until 3.13 when a configuration with these options was tried Signed-off-by:
David Cohen <david.a.cohen@linux.intel.com> Signed-off-by:
-
Denis Turischev authored
commit c09ec25d upstream. The same issue like with Panther Point chipsets. If the USB ports are switched to xHCI on shutdown, the xHCI host will send a spurious interrupt, which will wake the system. Some BIOS have work around for this, but not all. One example is Compulab's mini-desktop, the Intense-PC2. The bug can be avoided if the USB ports are switched back to EHCI on shutdown. This patch should be backported to stable kernels as old as 3.12, that contain the commit 638298dc "xhci: Fix spurious wakeups after S5 on Haswell" Signed-off-by:
Denis Turischev <denis@compulab.co.il> Signed-off-by:
-
Julius Werner authored
commit 1f81b6d2 upstream. We have observed a rare cycle state desync bug after Set TR Dequeue Pointer commands on Intel LynxPoint xHCs (resulting in an endpoint that doesn't fetch new TRBs and thus an unresponsive USB device). It always triggers when a previous Set TR Dequeue Pointer command has set the pointer to the final Link TRB of a segment, and then another URB gets enqueued and cancelled again before it can be completed. Further investigation showed that the xHC had returned the Link TRB in the TRB Pointer field of the Transfer Event (CC == Stopped -- Length Invalid), but when xhci_find_new_dequeue_state() later accesses the Endpoint Context's TR Dequeue Pointer field it is set to the first TRB of the next segment. The driver expects those two values to be the same in this situation, and uses the cycle state of the latter together with the address of the former. This should be fine according to the XHCI specification, since the endpoint ring should be stopped when returning the Transfer Event and thus should not advance over the Link TRB before it gets restarted. However, real-world XHCI implementations apparently don't really care that much about these details, so the driver should follow a more defensive approach to try to work around HC spec violations. This patch removes the stopped_trb variable that had been used to store the TRB Pointer from the last Transfer Event of a stopped TRB. Instead, xhci_find_new_dequeue_state() now relies only on the Endpoint Context, requiring a small amount of additional processing to find the virtual address corresponding to the TR Dequeue Pointer. Some other parts of the function were slightly rearranged to better fit into this model. This patch should be backported to kernels as old as 2.6.31 that contain the commit ae636747 "USB: xhci: URB cancellation support." Signed-off-by:
Julius Werner <jwerner@chromium.org> Signed-off-by:
-
Miao Xie authored
commit 1c70d8fb upstream. Currently, with inode cache enabled, we will reuse its inode id immediately after unlinking file, we may hit something like following: |->iput inode |->return inode id into inode cache |->create dir,fsync |->power off An easy way to reproduce this problem is: mkfs.btrfs -f /dev/sdb mount /dev/sdb /mnt -o inode_cache,commit=100 dd if=/dev/zero of=/mnt/data bs=1M count=10 oflag=sync inode_id=`ls -i /mnt/data | awk '{print $1}'` rm -f /mnt/data i=1 while [ 1 ] do mkdir /mnt/dir_$i test1=`stat /mnt/dir_$i | grep Inode: | awk '{print $4}'` if [ $test1 -eq $inode_id ] then dd if=/dev/zero of=/mnt/dir_$i/data bs=1M count=1 oflag=sync echo b > /proc/sysrq-trigger fi sleep 1 i=$(($i+1)) done mount /dev/sdb /mnt umount /dev/sdb btrfs check /dev/sdb We fix this problem by adding unlinked inode's id into pinned tree, and we can not reuse them until committing transaction. Signed-off-by:
Miao Xie <miaox@cn.fujitsu.com> Signed-off-by:
Wang Shilong <wangsl.fnst@cn.fujitsu.com> Signed-off-by:
Chris Mason <clm@fb.com> [ luis: backported to 3.11: adjusted context ] Signed-off-by:
-
Loic Poulain authored
commit f8fd1b03 upstream. __dma_tx_complete is not protected against concurrent call of serial8250_tx_dma. it can lead to circular tail index corruption or parallel call of serial_tx_dma on the same data portion. This patch fixes this issue by holding the port lock. Signed-off-by:
Loic Poulain <loic.poulain@intel.com> Reviewed-by:
Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by:
-
Loic Poulain authored
commit b08c9c31 upstream. On transmit-hold-register empty, serial8250_tx_chars should be called only if we don't use DMA. DMA has its own tx cycle. Signed-off-by:
-
Johan Hovold authored
commit 10164c2a upstream. Fix driver new_id sysfs-attribute removal deadlock by making sure to not hold any locks that the attribute operations grab when removing the attribute. Specifically, usb_serial_deregister holds the table mutex when deregistering the driver, which includes removing the new_id attribute. This can lead to a deadlock as writing to new_id increments the attribute's active count before trying to grab the same mutex in usb_serial_probe. The deadlock can easily be triggered by inserting a sleep in usb_serial_deregister and writing the id of an unbound device to new_id during module unload. As the table mutex (in this case) is used to prevent subdriver unload during probe, it should be sufficient to only hold the lock while manipulating the usb-serial driver list during deregister. A racing probe will then either fail to find a matching subdriver or fail to get the corresponding module reference. Since v3.15-rc1 this also triggers the following lockdep warning: ====================================================== [ INFO: possible circular locking dependency detected ] 3.15.0-rc2 #123 Tainted: G W ------------------------------------------------------- modprobe/190 is trying to acquire lock: (s_active#4){++++.+}, at: [<c0167aa0>] kernfs_remove_by_name_ns+0x4c/0x94 but task is already holding lock: (table_lock){+.+.+.}, at: [<bf004d84>] usb_serial_deregister+0x3c/0x78 [usbserial] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (table_lock){+.+.+.}: [<c0075f84>] __lock_acquire+0x1694/0x1ce4 [<c0076de8>] lock_acquire+0xb4/0x154 [<c03af3cc>] _raw_spin_lock+0x4c/0x5c [<c02bbc24>] usb_store_new_id+0x14c/0x1ac [<bf007eb4>] new_id_store+0x68/0x70 [usbserial] [<c025f568>] drv_attr_store+0x30/0x3c [<c01690e0>] sysfs_kf_write+0x5c/0x60 [<c01682c0>] kernfs_fop_write+0xd4/0x194 [<c010881c>] vfs_write+0xbc/0x198 [<c0108e4c>] SyS_write+0x4c/0xa0 [<c000f880>] ret_fast_syscall+0x0/0x48 -> #0 (s_active#4){++++.+}: [<c03a7a28>] print_circular_bug+0x68/0x2f8 [<c0076218>] __lock_acquire+0x1928/0x1ce4 [<c0076de8>] lock_acquire+0xb4/0x154 [<c0166b70>] __kernfs_remove+0x254/0x310 [<c0167aa0>] kernfs_remove_by_name_ns+0x4c/0x94 [<c0169fb8>] remove_files.isra.1+0x48/0x84 [<c016a2fc>] sysfs_remove_group+0x58/0xac [<c016a414>] sysfs_remove_groups+0x34/0x44 [<c02623b8>] driver_remove_groups+0x1c/0x20 [<c0260e9c>] bus_remove_driver+0x3c/0xe4 [<c026235c>] driver_unregister+0x38/0x58 [<bf007fb4>] usb_serial_bus_deregister+0x84/0x88 [usbserial] [<bf004db4>] usb_serial_deregister+0x6c/0x78 [usbserial] [<bf005330>] usb_serial_deregister_drivers+0x2c/0x4c [usbserial] [<bf016618>] usb_serial_module_exit+0x14/0x1c [sierra] [<c009d6cc>] SyS_delete_module+0x184/0x210 [<c000f880>] ret_fast_syscall+0x0/0x48 other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(table_lock); lock(s_active#4); lock(table_lock); lock(s_active#4); *** DEADLOCK *** 1 lock held by modprobe/190: #0: (table_lock){+.+.+.}, at: [<bf004d84>] usb_serial_deregister+0x3c/0x78 [usbserial] stack backtrace: CPU: 0 PID: 190 Comm: modprobe Tainted: G W 3.15.0-rc2 #123 [<c0015e10>] (unwind_backtrace) from [<c0013728>] (show_stack+0x20/0x24) [<c0013728>] (show_stack) from [<c03a9a54>] (dump_stack+0x24/0x28) [<c03a9a54>] (dump_stack) from [<c03a7cac>] (print_circular_bug+0x2ec/0x2f8) [<c03a7cac>] (print_circular_bug) from [<c0076218>] (__lock_acquire+0x1928/0x1ce4) [<c0076218>] (__lock_acquire) from [<c0076de8>] (lock_acquire+0xb4/0x154) [<c0076de8>] (lock_acquire) from [<c0166b70>] (__kernfs_remove+0x254/0x310) [<c0166b70>] (__kernfs_remove) from [<c0167aa0>] (kernfs_remove_by_name_ns+0x4c/0x94) [<c0167aa0>] (kernfs_remove_by_name_ns) from [<c0169fb8>] (remove_files.isra.1+0x48/0x84) [<c0169fb8>] (remove_files.isra.1) from [<c016a2fc>] (sysfs_remove_group+0x58/0xac) [<c016a2fc>] (sysfs_remove_group) from [<c016a414>] (sysfs_remove_groups+0x34/0x44) [<c016a414>] (sysfs_remove_groups) from [<c02623b8>] (driver_remove_groups+0x1c/0x20) [<c02623b8>] (driver_remove_groups) from [<c0260e9c>] (bus_remove_driver+0x3c/0xe4) [<c0260e9c>] (bus_remove_driver) from [<c026235c>] (driver_unregister+0x38/0x58) [<c026235c>] (driver_unregister) from [<bf007fb4>] (usb_serial_bus_deregister+0x84/0x88 [usbserial]) [<bf007fb4>] (usb_serial_bus_deregister [usbserial]) from [<bf004db4>] (usb_serial_deregister+0x6c/0x78 [usbserial]) [<bf004db4>] (usb_serial_deregister [usbserial]) from [<bf005330>] (usb_serial_deregister_drivers+0x2c/0x4c [usbserial]) [<bf005330>] (usb_serial_deregister_drivers [usbserial]) from [<bf016618>] (usb_serial_module_exit+0x14/0x1c [sierra]) [<bf016618>] (usb_serial_module_exit [sierra]) from [<c009d6cc>] (SyS_delete_module+0x184/0x210) [<c009d6cc>] (SyS_delete_module) from [<c000f880>] (ret_fast_syscall+0x0/0x48) Signed-off-by:
-
Liu Hua authored
commit 56b700fd upstream. For vmcore generated by LPAE enabled kernel, user space utility such as crash needs additional infomation to parse. So this patch add arch_crash_save_vmcoreinfo as what PAE enabled i386 linux does. Reviewed-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
Liu Hua <sdu.liu@huawei.com> Signed-off-by:
-
