- 23 Jul, 2022 1 commit
-
-
Luiz Augusto von Dentz authored
This adds the initial implementation of CIS connections and introduces the ISO packets/links. == Central: Set CIG Parameters, create a CIS and Setup Data Path == > tools/isotest -s <address> < HCI Command: LE Extended Create... (0x08|0x0043) plen 26 ... > HCI Event: Command Status (0x0f) plen 4 LE Extended Create Connection (0x08|0x0043) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 31 LE Enhanced Connection Complete (0x0a) ... < HCI Command: LE Create Connected... (0x08|0x0064) plen 5 ... > HCI Event: Command Status (0x0f) plen 4 LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 29 LE Connected Isochronous Stream Established (0x19) ... < HCI Command: LE Setup Isochronou.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 < HCI Command: LE Setup Isochronou.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 == Peripheral: Accept CIS and Setup Data Path == > tools/isotest -d HCI Event: LE Meta Event (0x3e) plen 7 LE Connected Isochronous Stream Request (0x1a) ... < HCI Command: LE Accept Co.. (0x08|0x0066) plen 2 ... > HCI Event: LE Meta Event (0x3e) plen 29 LE Connected Isochronous Stream Established (0x19) ... < HCI Command: LE Setup Is.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 < HCI Command: LE Setup Is.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 Signed-off-by:Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
-
- 22 Jul, 2022 39 commits
-
-
Luiz Augusto von Dentz authored
This introduces hci_recv_event_data to make it simpler to access the contents of last received event rather than having to pass its contents to the likes of *_ind/*_cfm callbacks. Signed-off-by: -
Brian Gix authored
The timed ending of Discoverability was handled in hci_requst.c, with calls using the deprecated hci_req_add() mechanism. Converted to live inside mgmt.c using the same delayed work queue, but with hci_sync version of hci_update_discoverable(). Signed-off-by:
Brian Gix <brian.gix@intel.com> Signed-off-by:
-
Brian Gix authored
This removes the remaining calls to HCI_OP_WRITE_SCAN_ENABLE from hci_request call chains, and converts them to hci_sync calls. Signed-off-by:
-
Brian Gix authored
The discov_update work queue is no longer used as a result of the hci_sync rework. The __hci_req_hci_power_on() function is no longer referenced in the code as a result of the hci_sync rework. Signed-off-by:
-
shaomin Deng authored
Delete the repeated word "that" in comments. Signed-off-by:
shaomin Deng <dengshaomin@cdjrlc.com> Signed-off-by:
-
Luiz Augusto von Dentz authored
This removes the use of hci_conn_hold from Get Conn Info and Get Clock Info since the callback can just do a lookup by address using the cmd data and only then set cmd->user_data to pass to the complete callback. Signed-off-by: -
Luiz Augusto von Dentz authored
This fixes using hci_conn_abort instead of using hci_conn_abort_sync. Signed-off-by: -
Luiz Augusto von Dentz authored
If a command cannot be sent or there is a internal error an errno maybe set instead of a command status. Signed-off-by: -
Luiz Augusto von Dentz authored
This adds bt_status which can be used to convert Unix errno to Bluetooth status. Signed-off-by: -
Luiz Augusto von Dentz authored
This splits hci_dev_open_sync so each stage is handle by its own function so it is easier to identify each stage. Signed-off-by: -
Manish Mandlik authored
Make use of hci_cmd_sync_queue for removing an advertisement monitor. Signed-off-by:
Manish Mandlik <mmandlik@google.com> Reviewed-by:
Miao-chen Chou <mcchou@google.com> Signed-off-by:
-
Manish Mandlik authored
Make use of hci_cmd_sync_queue for adding an advertisement monitor. Signed-off-by:
-
Zijun Hu authored
Core driver addtionally checks LMP feature bit "Erroneous Data Reporting" instead of quirk HCI_QUIRK_BROKEN_ERR_DATA_REPORTING to decide if HCI commands HCI_Read|Write_Default_Erroneous_Data_Reporting are broken, so remove this unnecessary quirk. Signed-off-by:
Zijun Hu <quic_zijuhu@quicinc.com> Tested-by:
-
Zijun Hu authored
Core driver addtionally checks LMP feature bit "Erroneous Data Reporting" instead of quirk HCI_QUIRK_BROKEN_ERR_DATA_REPORTING to decide if HCI commands HCI_Read|Write_Default_Erroneous_Data_Reporting are broken, so remove this unnecessary quirk for fake CSR controllers. Signed-off-by:
-
Zijun Hu authored
Core driver addtionally checks LMP feature bit "Erroneous Data Reporting" instead of quirk HCI_QUIRK_BROKEN_ERR_DATA_REPORTING to decide if HCI commands HCI_Read|Write_Default_Erroneous_Data_Reporting are broken, so remove this unnecessary quirk for QCA controllers. The reason why these two HCI commands are broken for QCA controllers is that feature "Erroneous Data Reporting" is not enabled by their firmware as shown by below log: @ RAW Open: hcitool (privileged) version 2.22 < HCI Command: Read Local Supported Commands (0x04|0x0002) plen 0 > HCI Event: Command Complete (0x0e) plen 68 Read Local Supported Commands (0x04|0x0002) ncmd 1 Status: Success (0x00) Commands: 288 entries ...... Read Default Erroneous Data Reporting (Octet 18 - Bit 2) Write Default Erroneous Data Reporting (Octet 18 - Bit 3) ...... < HCI Command: Read Default Erroneous Data Reporting (0x03|0x005a) plen 0 > HCI Event: Command Complete (0x0e) plen 4 Read Default Erroneous Data Reporting (0x03|0x005a) ncmd 1 Status: Unknown HCI Command (0x01) < HCI Command: Read Local Supported Features (0x04|0x0003) plen 0 > HCI Event: Command Complete (0x0e) plen 12 Read Local Supported Features (0x04|0x0003) ncmd 1 Status: Success (0x00) Features: 0xff 0xfe 0x0f 0xfe 0xd8 0x3f 0x5b 0x87 3 slot packets ...... Signed-off-by: -
Zijun Hu authored
BT core driver should addtionally check LMP feature bit "Erroneous Data Reporting" instead of quirk HCI_QUIRK_BROKEN_ERR_DATA_REPORTING set by BT device driver to decide if HCI commands HCI_Read|Write_Default_Erroneous_Data_Reporting are broken. BLUETOOTH CORE SPECIFICATION Version 5.3 | Vol 2, Part C | page 587 This feature indicates whether the device is able to support the Packet_Status_Flag and the HCI commands HCI_Write_Default_- Erroneous_Data_Reporting and HCI_Read_Default_Erroneous_- Data_Reporting. the quirk was introduced by 'commit cde1a8a9 ("Bluetooth: btusb: Fix and detect most of the Chinese Bluetooth controllers")' to mark HCI commands HCI_Read|Write_Default_Erroneous_Data_Reporting broken by BT device driver, but the reason why these two HCI commands are broken is that feature "Erroneous Data Reporting" is not enabled by firmware, this scenario is illustrated by below log of QCA controllers with USB I/F: @ RAW Open: hcitool (privileged) version 2.22 < HCI Command: Read Local Supported Commands (0x04|0x0002) plen 0 > HCI Event: Command Complete (0x0e) plen 68 Read Local Supported Commands (0x04|0x0002) ncmd 1 Status: Success (0x00) Commands: 288 entries ...... Read Default Erroneous Data Reporting (Octet 18 - Bit 2) Write Default Erroneous Data Reporting (Octet 18 - Bit 3) ...... < HCI Command: Read Default Erroneous Data Reporting (0x03|0x005a) plen 0 > HCI Event: Command Complete (0x0e) plen 4 Read Default Erroneous Data Reporting (0x03|0x005a) ncmd 1 Status: Unknown HCI Command (0x01) < HCI Command: Read Local Supported Features (0x04|0x0003) plen 0 > HCI Event: Command Complete (0x0e) plen 12 Read Local Supported Features (0x04|0x0003) ncmd 1 Status: Success (0x00) Features: 0xff 0xfe 0x0f 0xfe 0xd8 0x3f 0x5b 0x87 3 slot packets ...... Signed-off-by:
-
Zijun Hu authored
Event HCI_Truncated_Page_Complete should belong to central and HCI_Peripheral_Page_Response_Timeout should belong to peripheral, but hci_set_event_mask_page_2_sync() take these two events for wrong roles, so correct it by this change. Signed-off-by:
-
He Wang authored
Add VID/PID 0489:e0e2 for MediaTek MT7922 Bluetooth chip. Found and tested with Asus UM5302TA. From /sys/kernel/debug/usb/devices: T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0e2 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by:
He Wang <xw897002528@gmail.com> Signed-off-by:
-
Yuri D'Elia authored
This sets HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN for MTK controllers since SCO appear to not work when using HCI_OP_ENHANCED_SETUP_SYNC_CONN. Link: https://bugzilla.kernel.org/show_bug.cgi?id=215576Signed-off-by:
Yuri D'Elia <wavexx@thregr.org> Signed-off-by:
-
Hakan Jansson authored
Add device specific data for max baudrate in autobaud mode. This allows the host to use a baudrate higher than "init speed" when loading FW in autobaud mode. The device specific max baudrate in autobaud mode for CYW55572 is set to 921600 bps. Devices without device specific max baudrate in autobaud mode will use init speed as before. If no device specific init speed has been specified, it will default to the bcm_proto default 115200 bps. The increased baud rate improves FW load time. The exact load time will depend on the specific system and FW being used. As a rough indication, the FW load time dropped from ~9s @ 115.2kbps to ~1.7s @ 921.6kbps in one test. Signed-off-by:
Hakan Jansson <hakan.jansson@infineon.com> Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Hakan Jansson authored
Always prevent trying to set device baudrate before calling setup() when using autobaud mode. This was previously happening for devices which had device specific data with member no_early_set_baudrate set to 0. Signed-off-by:
-
Hakan Jansson authored
CYW55572 is a Wi-Fi + Bluetooth combo device from Infineon. Signed-off-by:
-
Hakan Jansson authored
Add conditional constraint to make property "reset-gpios" available only for compatible devices acually having the reset pin. Make property "brcm,requires-autobaud-mode" depend on property "shutdown-gpios" as the shutdown pin is required to enter autobaud mode. I looked at all compatible devices and compiled the matrix below before formulating the conditional constraint. This was a pure paper exercise and no verification testing has been performed. d e v h i o c s s e t h - - u w w v t r a a v d d e k k b d o s e e a i w e u u t o n t p p - - - - - - s s g g g g u u p p p p t p p i i i i x l p p o o o o c p l l s s s s o o y y --------------------------------------- brcm,bcm20702a1 X X X X X X X X brcm,bcm4329-bt X X X X X X X X brcm,bcm4330-bt X X X X X X X X brcm,bcm4334-bt X - X X X X X X brcm,bcm43438-bt X - X X X X X X brcm,bcm4345c5 X - X X X X X X brcm,bcm43540-bt X - X X X X X X brcm,bcm4335a0 X - X X X X X X brcm,bcm4349-bt X - X X X X X X infineon,cyw55572-bt X - X X X X X X Signed-off-by:Rob Herring <robh@kernel.org> Reviewed-by:
-
Hakan Jansson authored
CYW55572 is a Wi-Fi + Bluetooth combo device from Infineon. Extend the binding with its DT compatible. Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by:
-
Dan Carpenter authored
The bt_skb_sendmsg() function can't return NULL so there is no need to check for that. Several of these checks were removed previously but this one was missed. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Hilda Wu authored
Add the support ID(0x13D3, 0x3586) to usb_device_id table for Realtek RTL8852C. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3586 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by:
Hilda Wu <hildawu@realtek.com> Signed-off-by:
-
Hilda Wu authored
Add the support ID(0x13D3, 0x3587) to usb_device_id table for Realtek RTL8852C. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3587 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by:
-
Hilda Wu authored
Add the support ID(0x0CB8, 0xC558) to usb_device_id table for Realtek RTL8852C. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cb8 ProdID=c558 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by:
-
Hilda Wu authored
Add the support ID(0x04c5, 0x1675) to usb_device_id table for Realtek RTL8852C. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04c5 ProdID=1675 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by:
-
Hilda Wu authored
Add the support ID(0x04CA, 0x4007) to usb_device_id table for Realtek RTL8852C. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04ca ProdID=4007 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by:
-
Ying Hsu authored
Bluetooth HCI devices indicate if they are able to wakeup in the wakeup callback since 'commit 4539ca67 ("Bluetooth: Rename driver .prevent_wake to .wakeup")'. This patch adds a default wakeup callback for Bluetooth HCI UAR devices. It assumes Bluetooth HCI UART devices are wakeable for backward compatibility. For those who need a customized behavior, one can override it before calling hci_uart_register_device(). Fixes: 4539ca67 ("Bluetooth: Rename driver .prevent_wake to .wakeup") Signed-off-by:
Ying Hsu <yinghsu@chromium.org> Reviewed-by:
Alain Michaud <alainm@chromium.org> Signed-off-by:
-
Luiz Augusto von Dentz authored
These devices are likely going to be reprogrammed when disconnected so this avoid a whole bunch of commands attempt to remove and the add back to the list. Signed-off-by:
Zhengping Jiang <jiangzp@google.com>
-
Luiz Augusto von Dentz authored
When programming a new entry into the resolving list it shall default to network mode since the params may contain the mode programmed when the device was last added to the resolving list. Link: https://bugzilla.kernel.org/show_bug.cgi?id=209745 Fixes: 853b70b5 ("Bluetooth: hci_sync: Set Privacy Mode when updating the resolving list") Signed-off-by:
-
Tamas Koczka authored
Annotate hci_rx_work() with kcov_remote_start() and kcov_remote_stop() calls, so remote KCOV coverage is collected while processing the rx_q queue which is the main incoming Bluetooth packet queue. Coverage is associated with the thread which created the packet skb. The collected extra coverage helps kernel fuzzing efforts in finding vulnerabilities. This change only has effect if the kernel is compiled with CONFIG_KCOV, otherwise kcov_ functions don't do anything. Signed-off-by:
Tamas Koczka <poprdi@google.com> Tested-by:
Aleksandr Nogikh <nogikh@google.com> Reviewed-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
-
Zhengping Jiang authored
After resuming, remove setting scanning_paused to false, because it is checked and set to false in hci_resume_scan_sync. Also move setting the value to false before updating passive scan, because the value is used when resuming passive scan. Fixes: 3b420553 (Bluetooth: hci_sync: Fix attempting to suspend with unfiltered passive scan) Signed-off-by:
Abhishek Pandit-Subedi <abhishekpandit@chromium.org> Signed-off-by:
-
Sean Wang authored
Commit ce64b3e9 ("Bluetooth: mt7921s: Support wake on bluetooth") adds the wake on bluethooth via a dedicated GPIO. Extend the wake-on-bluetooth to use the SDIO DAT1 pin (in-band wakeup), when supported by the SDIO host driver. Co-developed-by:
Yake Yang <yake.yang@mediatek.com> Signed-off-by:
Sean Wang <sean.wang@mediatek.com> Reviewed-by:
AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by:
-
Zhengping Jiang authored
Set the connection data before calling get_conn_info_sync, so it can be verified the connection is still connected, before refreshing cached values. Fixes: 47db6b42 ("Bluetooth: hci_sync: Convert MGMT_OP_GET_CONN_INFO") Signed-off-by:
-
Luiz Augusto von Dentz authored
The scan response and advertising data needs to be tracked on a per instance (adv_info) since when these instaces are removed so are their data, to fix that new flags are introduced which is used to mark when the data changes and then checked to confirm when the data needs to be synced with the controller. Tested-by:
Tedd Ho-Jeong An <tedd.an@intel.com> Signed-off-by:
-
Luiz Augusto von Dentz authored
Both dev_name and short_name are not guaranteed to be NULL terminated so this instead use strnlen and then attempt to determine if the resulting string needs to be truncated or not. Link: https://bugzilla.kernel.org/show_bug.cgi?id=216018Signed-off-by:
-
