- 29 Jul, 2016 1 commit
-
-
Ulf Hansson authored
The system PM callbacks isn't used unless CONFIG_PM_SLEEP is set, thus it triggers a compiler warning about unused functions. Avoid this by changing from CONFIG_PM to CONFIG_PM_SLEEP. Reported-by:
Arnd Bergmann <arnd@arndb.de> Fixes: b70d0b3b5b29 ("mmc: sdhci-esdhc-imx: add esdhc specific suspend resume callback") Cc: Dong Aisheng <aisheng.dong@nxp.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Acked-by:
Dong Aisheng <aisheng.dong@nxp.com>
-
- 27 Jul, 2016 6 commits
-
-
Ulf Hansson authored
The SIMPLE_DEV_PM_OPS macro deals with the CONFIG_PM options when assigning the PM callbacks, thus it's not needed to control this when using the macro. By removing the non needed #ifdef, the code becomes a bit cleaner. Signed-off-by: -
Ulf Hansson authored
As the SET_SYSTEM_SLEEP_PM_OPS and the SET_RUNTIME_PM_OPS macro deals with the CONFIG_PM options when assigning the callbacks, it becomes redundant to control this when declaring the struct dev_pm_ops. Instead let's always declare it as it simplifies the code. Signed-off-by: -
Ulf Hansson authored
As the SET_SYSTEM_SLEEP_PM_OPS and the SET_RUNTIME_PM_OPS macro deals with the CONFIG_PM options when assigning the callbacks, it becomes redundant to control this when declaring the struct dev_pm_ops. Instead let's always declare it as it simplifies the code. Signed-off-by: -
Ulf Hansson authored
Let's use the SIMPLE_DEV_PM_OPS macro when declaring/assigning the system PM callbacks, as the code gets simplified. Signed-off-by: -
Ulf Hansson authored
By using the SET_SYSTEM_SLEEP_PM_OPS when assigning the system PM callbacks, we can remove some #ifdefs so code becomes a bit cleaner. Signed-off-by: -
Ulf Hansson authored
Convert to define the system PM callbacks to be build for CONFIG_PM_SLEEP and use the SET_SYSTEM_SLEEP_PM_OPS. In this way the code becomes cleaner. Signed-off-by:
-
- 25 Jul, 2016 33 commits
-
-
Baolin Wang authored
When mmc host HW supports busy signalling (using R1B as response), don't use the host->max_busy_timeout as the limitation when deciding the max discard sectors, which we inform the generic BLOCK layer about. Instead, let's use at least one preferred erase size as the max discard sectors. In cases when the host controller supports HW busy signalling and the timeout for the erase operation doesn't exceed the max_busy_timeout, we keep the R1B response, otherwise we prevent the host from doing HW busy detection by converting to a R1 response. Signed-off-by:
Baolin Wang <baolin.wang@linaro.org> Signed-off-by:
-
Douglas Anderson authored
Two times out of 2000 reboots I ran into the error message "rockchip_emmc_phy_power: dllrdy timeout". Presumably there is some corner case where the DLL just takes a little longer to timeout. Let's give it even more time to handle these corner cases. Signed-off-by:
Douglas Anderson <dianders@chromium.org> Acked-by:
Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by:
-
Douglas Anderson authored
It's possible that there are some reasons to turn the PHY on while the clock is 0. In this case we just won't wait for the DLL to lock. This is a bit of a stopgap until we figure out exactly when we're supposed to wait for the DLL to lock and when we're supposed to power cycle the PHY. Note: this patch should help with suspend/resume where the system will try to turn the PHY back on when the clock is 0. Signed-off-by:
-
Douglas Anderson authored
This reverts commit 4ac0d5f245e1 ("mmc: sdhci-of-arasan: Always power the PHY off/on when clock changes"), resolving conflicts with other patches that have come after. It appears that on some boards / with some eMMC devices that the patch is causing problems. Presumably turning the phy off and on again at the wrong time while initially setting up the card is confusing the card, the host, or the PHY. We have lots of power cycles while initially setting up the card because the main sdhci driver often turns off the clock by clearing SDHCI_CLOCK_CARD_EN and then calls host->ops->set_clock() to set the clock again. With all of those, we ended up with lots of power cycles. Presumably the arguments made in the original patch still hold. That is, whenever the card clock is turned off and on again (or changed) we really should wait for the DLL to lock again. However, perhaps it's really not that critical for the lower speeds. It's possible that the right answer here is: * Whenever set_clock() is called we should double-check that the DLL is locked. * Whenever set_clock() is called and we're actually changing clocks we should do a power cycle around that. * When we're doing a power cycle just because the clock changed, we probably shouldn't do quite as many things (maybe don't need to recalibarate, etc). Unfortunately the interaction between SDHCI and the PHY is extremely limited because of the limited PHY API. The PHY does have a reference to the card clock and could theoretically register for notifications, except that our clock is query only (it uses CLK_GET_RATE_NOCACHE) and so can't really be notified about updates. I believe we would need a major redesign of clock handling in SDHCI core to do better than that, or we would need to make our one fake notifications. :( Let's hope that we can eventually get more information from Arasan on how all this should be handled before doing tons more work. Until then, let's get back to a known working state. Note that the rest of the patches in the 150 MHz series should still work fine even without this one. Signed-off-by:Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
-
Georgi Djakov authored
Enabling support for ultra high speed mode cards requires some voltage switching and interaction with the PMIC via a special power IRQ. Add support for this. Signed-off-by:
Georgi Djakov <georgi.djakov@linaro.org> Acked-by:
-
Ritesh Harjani authored
To allow UHS mode to work properly, we need to implement a Qualcomm specific set_uhs_signaling() callback function. This function differs from the sdhci_set_uhs_signaling() in that we need check the clock rate and enable UHS timing only if the frequency is above 100MHz. This patch resolves the mmc_select_hs200 timeouts noticed after merging commit a5c1f3e55c99 ("mmc: mmc: do not use CMD13 to get status after speed mode switch") mmc0: mmc_select_hs200 failed, error -110 mmc0: error -110 whilst initialising MMC card mmc0: Reset 0x1 never completed. sdhci: =========== REGISTER DUMP (mmc0)=========== sdhci: Sys addr: 0x00000000 | Version: 0x00002e02 sdhci: Blk size: 0x00004000 | Blk cnt: 0x00000000 sdhci: Argument: 0x00000000 | Trn mode: 0x00000000 sdhci: Present: 0x01f80000 | Host ctl: 0x00000000 sdhci: Power: 0x00000000 | Blk gap: 0x00000000 sdhci: Wake-up: 0x00000000 | Clock: 0x00000003 sdhci: Timeout: 0x00000000 | Int stat: 0x00000000 sdhci: Int enab: 0x00000000 | Sig enab: 0x00000000 sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000 sdhci: Caps: 0x322dc8b2 | Caps_1: 0x00008007 sdhci: Cmd: 0x00000000 | Max curr: 0x00000000 sdhci: Host ctl2: 0x00000000 sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x0000000000000000 sdhci: =========================================== Fixes: a5c1f3e55c99 ("mmc: mmc: do not use CMD13 to get status after...") Signed-off-by:Ritesh Harjani <riteshh@codeaurora.org> Signed-off-by:
-
Georgi Djakov authored
The controller does not clear the "reset bit" when it is reset without a card in the slot. Because of this, the following error message is seen while booting with no plugged SD card. mmc1: Reset 0x1 never completed. Add the SDHCI_QUIRK_NO_CARD_NO_RESET quirk to avoid this. Signed-off-by:
Ivan T. Ivanov <ivan.ivanov@linaro.org> Signed-off-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Acked-by:
-
Jon Hunter authored
To support UHS modes for Tegra an external regulator must be present to adjust the IO voltage accordingly. Even if the regulator is not present but the host supports the UHS modes and the device supports the UHS modes, then we will attempt to switch to a high-speed mode. Without an external regulator, Tegra will fail to switch to the high-speed mode. It has been found that with some SD cards, that once it has been switch to operate at a high-speed mode, all subsequent commands issues to the card will fail and so it will not be possible to switch back to a non high-speed mode and so the SD card initialisation will fail. The SDHCI core does not require that the host have an external regulator when switching to UHS modes and therefore, the Tegra SDHCI host controller should only advertise the UHS modes as being supported if the regulator for the IO voltage is present. Fortunately, Tegra has a vendor specific register which can be used to control which modes are advertised via the SDHCI_CAPABILITIES register. Hence, if there is no IO voltage regulator available for the Tegra SDHCI host, then don't advertise the UHS modes. Note that if the regulator is not available, we also don't advertise that the SDHCI is compatible with v3.0 of the SDHCI specification because this will read the SDHCI_CAPABILITIES_1 register which will enable other UHS modes. This fixes commit 7ad2ed1d ("mmc: tegra: enable UHS-I modes") which enables UHS mode without checking if the board can support them. Fixes: 7ad2ed1d ("mmc: tegra: enable UHS-I modes") Signed-off-by:
Jon Hunter <jonathanh@nvidia.com> Acked-by:
-
Jon Hunter authored
The capabilities of the SDHCI host controller are read early during the SDHCI host initialisation in sdhci_setup_host() and before any regulators for the host have been requested. This means that if the host supports some high-speed modes (according to its capabilities register), but the board cannot because the appropriate voltage regulator is not available, then the host cannot easily override the capabilities that are supported. To allow a SDHCI host controller to determine if it can support UHS high speed modes via the presence of the MMC regulators, request the regulators before reading the capabilities of the host controller. This will allow the SDHCI host to use the 'reset' callback to take the appropriate action (set flags, configure registers, etc) before the capabilities register(s) are read. Please note that some SDHCI hosts, such as the Tegra SDHCI host, has the ability to mask bits in the capabilities register to prevent certain capabilities from being advertised. Signed-off-by:
-
Andy Shevchenko authored
Everywhere else in the code MRFLD abbreviation is used for Intel Merrifield. Do the same for sdhci-pci. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by:
-
Dong Aisheng authored
The tuning bits like FBCLK_SEL, SMP_CLK_SEL and DLY_CELL which affects timing may have already been set by ROM if booting from SD3.0 mode like SDR104. Let's clear it first during driver probe before doing the new card enumeration to avoid working on the wrong timing. Note that tuning bits are dynamical settings which may need to be kept during MMC_PM_KEEP_POWER suspend, so we did not put them into hwinit function. Signed-off-by:
-
Dong Aisheng authored
sdhci_esdhc_imx_hwinit() includes all basic hw intialization. Calling it after resume to re-initialize hw in case its state is already lost in low power mode. Signed-off-by:
-
Dong Aisheng authored
Move tuning static configuration into basic hwinit function. Tuning configuration may also be lost in low power mode, so need restore in hwinit(). Acked-by:
-
Dong Aisheng authored
Move all hw related static initializations into a separate function which helps concentrate the hw related initialization code. And that function could also be called by other places later as a basic hw state restore. e.g. suspend/resume where the hw state is possible to lost due to low power mode. Signed-off-by:
-
Dong Aisheng authored
When enable DDR, the clock factor definition is changed. e.g. original 200Mhz will become 100Mhz once MIX_CTRL_DDREN bit is set So we need to update the clock setting then the strobe dll can lock the correct clock rate. Additionally we also need disable the clock before locking strobe dll. Acked-by:
-
Dong Aisheng authored
Indicating hw auto retuning support for mx6qdl in the fake caps_1 register and enable auto retuning in post_tuning process after tuning completes. Acked-by:
-
Dong Aisheng authored
Enable HW auto retuning when set SDHCI_CTRL_EXEC_TUNING and clear it when clear SDHCI_CTRL_TUNED_CLK. Acked-by:
-
Dong Aisheng authored
If HW supports SDHCI_TUNING_MODE_3 which is auto retuning, we won't retune during runtime suspend and resume, instead we use Re-tuning Request signaled via SDHCI_INT_RETUNE interrupt to do retuning and hw auto retuning during data transfer to guarantee the signal sample window correction. This can avoid a mass of repeatedly retuning during small file system data access and improve the performance. Signed-off-by:
-
Dong Aisheng authored
add tuning start point binding Signed-off-by:
-
Dong Aisheng authored
The delay cells of some SoCs may have less delay per one cell, for such SoCs, user could set the start delay cell point to bypass the first a few meaningless tuning commands. Acked-by:
-
Dong Aisheng authored
Disable DLL delay line settings explicitly during driver initialization in case ROM/uBoot had set an invalid delay. e.g. MX6DL ROM has set the default delay line(DLLCTRL) to 0x1000021, the uSDHC clock timing will become marginal when works on DDR mode due to default delay and will possibly see CRC errors in case the board is not perfectly designed on the eMMC chip layout. Acked-by:
-
Dong Aisheng authored
Currently, we config the watermark_level register only in probe. This will cause the mmc write operation timeout issue after system resume back in LPSR mode. Because in LPSR mode, after system resume back, the watermark_level register(0x44) changes to 0x08000880, which set the write watermark level as 0, and set the read watermark level as 128. This value is incorrect. This patch restores the setting of watermark level register after system resume back. Signed-off-by:
-
Dong Aisheng authored
It will be used for platform specific suspend/resume state save/restore work for some low power mode like Mega/Fast or LPSR mode. Acked-by:
-
Dong Aisheng authored
The driver has already implemented the private .set_timeout() callback for common SDHCI code to do correct timeout value setting, it does not need call sdhci_calc_timeout(), so this quirk actually is not working. Remove it now. Acked-by:
-
Dong Aisheng authored
Switch to use the more robust common mmc_regulator_set_vqmmc() function in MMC core which set the target voltage as close as possible to target voltage. We did not re-factor the whole sdhci_start_signal_voltage_switch() cause we want to keep the original signal switch order between host and card to avoid potential break. Signed-off-by:
-
Andy Shevchenko authored
This makes the error handling much more simpler than open-coding everything and in addition makes the probe function smaller an tidier. Signed-off-by:
-
Bojan Prtvar authored
Export DSR register through sysfs same as we did for the CID, CSD and OCR registers. Signed-off-by:
Bojan Prtvar <prtvar.b@gmail.com> Signed-off-by:
-
Jaehoon Chung authored
In dw_mmc.c, it's enabled by default. It doesn't need to set MMC_CAP_ERASE in rockchip anymore. Signed-off-by:
Jaehoon Chung <jh80.chung@samsung.com> Acked-by:
Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by:
-
Jaehoon Chung authored
This flag needs to use the trim/discard/erase commands. dwmmc controller enables this flag by default. Signed-off-by:
-
Shawn Lin authored
The reason for why we expose these to dt is that some of the controller is unable to send special cmd type due to the hw limitation. Signed-off-by:
-
Shawn Lin authored
This patch adds description for no-sd, no-sdio, no-mmc. We expose these to DT as some of the controllers are unable to deal with special cmd type due to hw limitation. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Bojan Prtvar authored
Registers CID and CSD are already exported through sysfs so let's make this interface complete by adding missing OCR register. Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Stefan Wahren authored
The capabilities in iproc platform data are magic numbers. So replace them with the proper capability defines to make it readable. Signed-off-by:
Stefan Wahren <stefan.wahren@i2se.com> Acked-by:
Scott Branden <scott.branden@broadcom.com> Acked-by:
-
